MC33XX
Mobile Computer
User Guide
for Android ™ 7.1.2 Nougat
MN-003131-04 Rev A
Copyright
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many
jurisdictions worldwide. Google, Android, Google Play and other marks are trademarks of Google LLC.All other
trademarks are the property of their respective owners. ©2019 Zebra Technologies Corporation and/or its affiliates.
All rights reserved.
COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to www.zebra.com/
copyright.
WARRANTY: For complete warranty information, go to www.zebra.com/warranty
END USER LICENSE AGREEMENT: For complete EULA information, go to www.zebra.com/eula
Terms of Use
• Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
• Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
• Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
• Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business
interruption, or loss of business information) arising out of the use of, the results of use of, or inability to
use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
.
.
Revision History
Changes to the original guide are listed below:
Change Date Description
-01 Rev A 12/2017 Initial release.
-02 Rev A 03/2018 Updated to include MC33XX-R and MC33XX-S Configurations.
2
Change Date Description
-03 Rev A 06/2019 Updated to include the Application Notification LED in the Features section and add
the topics Pulse Notification Light and Interactive Sensor Technology.
-04 Rev A 09/2019 Updated to indicate the lanyard is compatible only with the MC33XX-R and
MC33XX-S configurations, remove screws on the forklift mount, and replace the
Screen Protector Mode screen.
3
Table of Contents
Copyright ........................................................................................................................................... 2
Terms of Use .................................................................................................................................... 2
Revision History ................................................................................................................................ 2
About This Guide
Introduction ..................................................................................................................................... 12
Configurations ................................................................................................................................. 12
Software Versions ........................................................................................................................... 15
Chapter Descriptions ...................................................................................................................... 15
Notational Conventions ................................................................................................................... 15
Icon Conventions ............................................................................................................................ 16
Related Documents ........................................................................................................................ 16
Service Information ......................................................................................................................... 16
Provide Documentation Feedback .................................................................................................. 17
Getting Started
Introduction ..................................................................................................................................... 18
MC33XX-G Features ...................................................................................................................... 18
MC33XX-R Features ....................................................................................................................... 21
Rotating Scan Turret ................................................................................................................. 23
MC33XX-S Features ....................................................................................................................... 24
Unpacking ....................................................................................................................................... 26
Setup ............................................................................................................................................... 26
Installing a microSD Card ......................................................................................................... 26
Installing the MC33XX-G Battery .............................................................................................. 29
Installing the MC33XX-R/S Battery ........................................................................................... 30
Charging the Battery ................................................................................................................. 31
Backup Power ..................................................................................................................... 33
Charging Temperature ........................................................................................................ 33
Charging Spare Batteries .................................................................................................... 33
Hot Swap Mode ......................................................................................................................... 33
Google Account Setup .............................................................................................................. 33
Replacing the Battery in the MC33XX-G ........................................................................................ 34
Replacing the Battery in the MC33XX-R/S ..................................................................................... 36
Accessing Device Settings .............................................................................................................. 38
Battery Management ....................................................................................................................... 38
4
Table of Contents
Monitor Battery Usage .............................................................................................................. 38
Low Battery Notification ............................................................................................................ 39
Battery Optimization .................................................................................................................. 39
Turning Off the Radios ........................................................................................................ 40
Connecting a Wired Headset .......................................................................................................... 40
Real-Time Clock Backup ................................................................................................................ 40
Setting the Date and Time .............................................................................................................. 40
Display Setting ................................................................................................................................ 41
Setting the Screen Brightness ................................................................................................... 41
Changing the Screen Timeout Setting ...................................................................................... 41
Setting Font Size ....................................................................................................................... 41
Setting Screen Rotation ............................................................................................................ 42
Touch Panel Mode .................................................................................................................... 42
General Sound Setting .................................................................................................................... 43
Wake-Up Sources ........................................................................................................................... 44
Using the MC33XX
Introduction ..................................................................................................................................... 46
Google Mobile Services .................................................................................................................. 46
Home Screen .................................................................................................................................. 47
Setting Home Screen Rotation .................................................................................................. 48
Status Bar ................................................................................................................................. 48
Status Icons ........................................................................................................................ 49
Notification Icons ................................................................................................................. 50
Managing Notifications .............................................................................................................. 51
Setting Application Notifications .......................................................................................... 51
Viewing Notification Settings for All Apps ........................................................................... 51
Controlling Lock Screen Notifications ................................................................................. 51
Pulse Notification Light ........................................................................................................ 52
Quick Access Panel .................................................................................................................. 52
Edit Icons on Quick Settings ............................................................................................... 53
Application Shortcuts and Widgets ........................................................................................... 54
Adding an Application to the Home Screen ........................................................................ 54
Adding a Widget to the Home Screen ................................................................................. 54
Moving Items on the Home Screen ..................................................................................... 54
Removing an Application Shortcut or Widget from the Home Screen ................................ 54
Folders ............................................................................................................................................ 54
Creating Folders ........................................................................................................................ 54
Naming Folders ......................................................................................................................... 55
Removing Folders ..................................................................................................................... 55
Home Screen Wallpaper ................................................................................................................. 55
Using the Touchscreen ................................................................................................................... 55
Keyboards ....................................................................................................................................... 56
Keyboard Configuration ............................................................................................................ 56
Using the Enterprise Keyboard ................................................................................................. 56
Numberic Tab ...................................................................................................................... 57
Alpha Tab ............................................................................................................................ 57
Additional Character Tab .................................................................................................... 58
Scan Tab ............................................................................................................................. 58
Using the Android Keyboard ..................................................................................................... 58
5
Table of Contents
Editing Text ......................................................................................................................... 59
Entering Numbers, Symbols and Special Characters ......................................................... 59
Hiding On-Screen Keyboard ............................................................................................... 59
Switching Language Keyboards .......................................................................................... 59
Do Not Disturb Feature ................................................................................................................... 60
Limit Sounds and Vibrations ..................................................................................................... 60
Total Silence ....................................................................................................................... 60
Alarms Only ......................................................................................................................... 60
Priority Notifications Only .................................................................................................... 61
Automatically Block Sounds and Vibrations .................................................................................... 61
Silence Sounds During Certain Times ...................................................................................... 61
Silence Sounds During Events and Meetings ........................................................................... 62
Turn Sounds Back On ............................................................................................................... 62
Override Do Not Disturb for Specific Apps ................................................................................ 62
Applications ..................................................................................................................................... 62
Accessing Applications ............................................................................................................. 67
Switching Between Recent Applications ................................................................................... 68
Un-Locking the Screen ................................................................................................................... 68
Resetting the Device ....................................................................................................................... 70
Performing a Soft Reset ............................................................................................................ 71
Performing a Hard Reset .......................................................................................................... 71
Suspend Mode ................................................................................................................................ 71
Transferring Files with a Host Computer via USB .......................................................................... 71
Transferring Files using Media Transfer Protocol ..................................................................... 71
Transferring Files using Photo Transfer Protocol ...................................................................... 72
Disconnect from the Host Computer ......................................................................................... 73
Applications
Introduction ..................................................................................................................................... 74
Battery Manager ............................................................................................................................. 74
File Browser .................................................................................................................................... 76
Contacts .......................................................................................................................................... 78
Adding Contacts ........................................................................................................................ 78
Editing Contacts ........................................................................................................................ 78
Deleting Contacts ...................................................................................................................... 78
Camera ........................................................................................................................................... 79
Taking Photos ........................................................................................................................... 79
Taking a Panoramic Photo .....................................................................................................
Recording Videos ...................................................................................................................... 81
Photo Settings ........................................................................................................................... 81
Video Settings ........................................................................................................................... 82
Gallery ............................................................................................................................................. 83
Working with Albums ................................................................................................................. 85
Share an Album .................................................................................................................. 86
Get Album Information ........................................................................................................ 86
Deleting an Album ............................................................................................................... 87
Working with Photos ................................................................................................................. 87
Viewing and Browsing Photos ............................................................................................. 87
Cropping a Photo ................................................................................................................ 88
Setting a Photo as a Contact Icon ....................................................................................... 88
... 80
6
Table of Contents
Share a Photo ..................................................................................................................... 89
Deleting a Photo .................................................................................................................. 89
Working with Videos .................................................................................................................. 89
Watching Videos ................................................................................................................. 89
Sharing a Video ................................................................................................................... 89
Deleting a Video .................................................................................................................. 90
Photos ............................................................................................................................................. 90
Working with Albums ................................................................................................................. 90
Deleting an Album ............................................................................................................... 91
Working with Photos ................................................................................................................. 91
Viewing and Browsing Photos ............................................................................................. 91
Cropping a Photo ................................................................................................................ 91
Setting a Photo as a Contact Icon ....................................................................................... 92
Share a Photo ..................................................................................................................... 92
Deleting a Photo .................................................................................................................. 92
Working with Videos .................................................................................................................. 93
Watching Videos ................................................................................................................. 93
Sharing a Video ................................................................................................................... 93
Deleting a Video .................................................................................................................. 93
DataWedge Demonstration ............................................................................................................. 94
Sound Recorder .............................................................................................................................. 95
PTT Express Voice Client ............................................................................................................... 96
PTT Audible Indicators .............................................................................................................. 96
Notification Icons ....................................................................................................................... 97
Enabling PTT Communication .................................................................................................. 97
Selecting a Talk Group .............................................................................................................. 98
PTT Communication ................................................................................................................. 98
Creating a Group Call ......................................................................................................... 98
Responding with a Private Response ................................................................................. 98
Disabling PTT Express Voice Client Communication ......................................................... 98
RxLogger ........................................................................................................................................ 99
Enabling Logging ...................................................................................................................... 99
Disabling Logging ...................................................................................................................... 99
RxLogger Utility ............................................................................................................................. 100
Diagnostic Tool ..............................................................................................................
Settings ............................................................................................................................. 103
Battery Test Information .................................................................................................... 103
GPS Test Information ........................................................................................................ 103
System Test Information ................................................................................................... 103
WLAN Test Information ..................................................................................................... 104
WWAN Test Information ................................................................................................... 104
Bluetooth Test Information ................................................................................................ 104
Device Central .............................................................................................................................. 105
Device Central Tabs ................................................................................................................ 105
Paging an RS6000 Ring Scanner ........................................................................................... 106
SimulScan Demo .......................................................................................................................... 107
Exporting Sample Forms ......................................................................................................... 108
Postal, Transportation and Logistics Example ........................................................................ 108
Manufacturing Example .......................................................................................................... 110
Settings ................................................................................................................................... 112
Advanced Settings .................................................................................................................. 113
............... 101
7
Table of Contents
Demo Customization ............................................................................................................... 114
Default Templates ............................................................................................................. 115
Data Capture
Introduction ................................................................................................................................... 116
Imager ........................................................................................................................................... 116
Operational Modes .................................................................................................................. 116
Laser Scanner ............................................................................................................................... 117
RS507/RS507X Hands-Free Imager ............................................................................................ 117
RS6000 Bluetooth Ring Scanner .................................................................................................. 117
DS3678 Digital Scanner ................................................................................................................ 118
Scanning Considerations .............................................................................................................. 118
Barcode Capture with Imager ....................................................................................................... 119
Barcode Capture with Laser Scanner ........................................................................................... 120
Barcode Capture with RS507/RS507X Hands-Free Imager ......................................................... 121
Barcode Capture with RS6000 Bluetooth Ring Scanner .............................................................. 122
Barcode Capture with DS3678 Bluetooth Scanner ....................................................................... 123
Pairing the RS507/RS507X/RS6000/DS3578 .............................................................................. 124
Pairing Using Near Field Communication ............................................................................... 124
Pairing in HID Mode Using Near Field Communication .......................................................... 125
Pairing the RS507/RS507X/RS6000/DS3678 Using SSI ........................................................ 126
Pairing the RS507/RS507X/RS6000 Hands-Free Imager Bluetooth HID ............................... 127
Pairing the DS3678 Digital Scanner ............................................................................................. 128
Pairing the DS3678 Using Bluetooth HID ............................................................................... 128
DataWedge ................................................................................................................................... 128
Enabling DataWedge .............................................................................................................. 128
Disabling DataWedge ............................................................................................................. 129
Wireless
Introduction ................................................................................................................................... 130
Wireless Local Area Networks ...................................................................................................... 130
Scan and Connect to a Wi-Fi Network .................................................................................... 131
Advanced Wi-Fi Settings ......................................................................................................... 131
Wi-Fi Direct ....................................................................................................................... 132
WPS Pin Entry .................................................................................................................. 132
Additional Wi-Fi Settings ......................................................................................................... 133
Remove a Wi-Fi Network ........................................................................................................ 134
Bluetooth ....................................................................................................................................... 135
Adaptive Frequency Hopping .................................................................................................. 135
Security ................................................................................................................................... 135
Bluetooth Profiles ............................................
Bluetooth Power States ........................................................................................................... 136
Bluetooth Radio Power ........................................................................................................... 137
Enabling Bluetooth ............................................................................................................ 137
Disabling Bluetooth ........................................................................................................... 137
Discovering Bluetooth Device(s) ............................................................................................. 137
Changing the Bluetooth Name ................................................................................................ 138
Connecting to a Bluetooth Device ........................................................................................... 138
Selecting Profiles on the Bluetooth Device ............................................................................. 138
........................................................................ 136
8
Table of Contents
Unpairing a Bluetooth Device .................................................................................................. 139
Using a Bluetooth Headset ..................................................................................................... 139
Near Field Communications .......................................................................................................... 139
Reading NFC Cards ................................................................................................................ 140
Sharing Information Using NFC .............................................................................................. 140
Accessories
Introduction ................................................................................................................................... 142
MC33XX Accessories ................................................................................................................... 142
Compatibility ................................................................................................................................. 147
Battery Comparison ................................................................................................................ 147
Battery Compatibility ............................................................................................................... 147
1-Slot USB Charge Cradle ............................................................................................................ 149
Charging the MC33XX Battery ................................................................................................ 149
Charging an MC33XX Spare Battery ...................................................................................... 150
Battery Charging in 1- Slot USB Charge Cradle ..................................................................... 151
Charging Temperature ...................................................................................................... 151
5-Slot Charge Only ShareCradle .................................................................................................. 153
Charging the MC33XX Battery ................................................................................................ 153
Battery Charging in the 5-Slot Charge Only ShareCradle ....................................................... 154
Charging Temperature ...................................................................................................... 154
5-Slot Ethernet ShareCradle ......................................................................................................... 155
Charging the MC33XX Battery ................................................................................................ 155
Battery Charging in the 5-Slot Ethernet ShareCradle ............................................................. 156
Charging Temperature ...................................................................................................... 156
5-Slot ShareCradle with 4-Slot Battery Charger ........................................................................... 157
Charging the MC33XX Battery ................................................................................................ 157
Charging Spare Batteries ........................................................................................................ 158
Battery Charging in the 5-Slot ShareCradle with 4-Slot Battery Charger ................................ 158
Charging Temperature ...................................................................................................... 158
5-Slot Ethernet ShareCradle with 4-Slot Battery Charger ............................................................. 159
Charging the MC33XX Battery ................................................................................................ 159
Charging Spare Batteries ........................................................................................................ 160
Battery Charging in the 5-Slot Ethernet ShareCradle with 4-Slot Battery Charger ................. 160
Charging Temperature ...................................................................................................... 160
4-Slot Spare Battery Charger ........................................................................................................ 160
Charging Spare Batteries ........................................................................................................ 161
Battery Charging ..................................................................................................................... 161
Spare Battery Charging ..................................................................................................... 161
Charging Temperature ...................................................................................................... 162
20-Slot Spare Battery Charger ...................................................................................................... 162
Charging Spare Batteries ........................................................................................................ 163
Battery Charging ..................................................................................................................... 163
Spare Battery Charging ..................................................................................................... 163
Charging Temperature ...................................................................................................... 164
USB Charge Cable ....................................................................................................................... 165
Connecting the USB Charge Cable to Device ........................................................................ 165
Connecting the USB Charge Cable to Host Computer ........................................................... 166
Main Battery Charging ...................................................................................................... 166
Charging the Device ................................................................................................................ 167
9
Table of Contents
Main Battery Charging ...................................................................................................... 167
Disconnecting the USB Charge Cable .................................................................................... 168
MC33XX Charge Only Adapter ..................................................................................................... 169
Adapter Installation ................................................................................................................. 169
Charging Temperature ...................................................................................................... 171
MC33XX-G Rubber Boot .............................................................................................................. 172
MC33XX-R Rubber Boot ............................................................................................................... 173
MC33XX-S Rubber Boot ............................................................................................................... 175
Rigid Holster ................................................................................................................................. 176
MC33XX-G Fabric Holster ............................................................................................................ 178
Belt Strap ................................................................................................................................ 178
Shoulder Strap ........................................................................................................................ 178
Using the Belt Strap ................................................................................................................ 179
Using the Shoulder Strap ........................................................................................................ 181
MC33XX-R/S Fabric Holster ......................................................................................................... 183
Belt Clip ................................................................................................................................... 183
Shoulder Strap ........................................................................................................................ 183
Using the Belt Clip ................................................................................................................... 184
Using the Shoulder Strap ........................................................................................................ 186
Un-powered Forklift Mount ............................................................................................................ 188
Replacement Hand Strap for MC33XX-G ..................................................................................... 190
Replacement Hand Strap for MC33XX-R/S .................................................................................. 192
Lanyard ......................................................................................................................................... 194
Install Lanyard on MC33XX .................................................................................................... 194
Using the Cross-body Strap .................................................................................................... 195
Using the Belt Clip ................................................................................................................... 196
Charging the MC33XX with the Lanyard ................................................................................. 197
Maintenance and Troubleshooting
Introduction ................................................................................................................................... 198
Maintaining the MC33XX .............................................................................................................. 198
Battery Safety Guidelines ............................................................................................................. 199
Cleaning Instructions .................................................................................................................... 199
Approved Cleanser Active Ingredients .................................................................................... 200
Harmful Ingredients ................................................................................................................. 200
Cleaning Instructions ............................................................................................................... 200
Special Cleaning Notes ........................................................................................................... 200
Cleaning Materials Required ................................................................................................... 200
Cleaning Frequency ................................................................................................................ 200
Cleaning the MC33XX .................................................................................................................. 201
Housing ................................................................................................................................... 201
Display .................................................................................................................................... 201
Exit Window ............................................................................................................................ 201
Connector Cleaning ................................................................................................................ 201
Cleaning Cradle Connectors ......................................................................................................... 201
Troubleshooting the MC33XX ....................................................................................................... 202
Technical Specifications
Introduction ................................................................................................................................... 205
10
Table of Contents
MC33XX Technical Specifications ................................................................................................ 205
MC33XX Keypads
Introduction ................................................................................................................................... 210
MC33XX 29-Key Keypad .............................................................................................................. 210
MC33XX 38-Key Keypad .............................................................................................................. 213
MC33XX 47-Key Keypad .............................................................................................................. 217
Index
11
About This Guide
Introduction
This guide provides information about using the MC33XX mobile computer and accessories.
NOTE: Screens and windows pictured in this guide are samples and can differ from actual screens.
Configurations
MC33XX used in this guide refers to all configurations, except where noted. MC33XX-G refers to the Trigger
configuration. MC33XX-R refers to the Rotate configuration. MC33XX-S refers to the Straight configuration.
MC33XX-S45 refers to the 45 degree angle Straight configuration.
This guide covers the following configurations:
Table 1 Configurations
Configuration Radios Display Memory
MC33XX–G
Standard
MC33XX–G
Premium
WLAN: IEEE
802.11a/b/g/n/ac/d
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
WLAN: IEEE
802.11a/b/g/n/ac/d
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
®
®
4.0” color 2 GB RAM /
16 GB Flash
4.0” color 4 GB RAM /
16 GB Flash
Data Capture
Options
SE965 1D,
SE4750-SR 2D
SE965 1D,
SE4750-SR 2D,
SE4850-ER 2D
Operating
System
Android-based
AOSP/GMS 7.1.2
Android-based
AOSP/GMS 7.1.2
12
Table 1 Configurations (Continued)
About This Guide
Configuration Radios Display Memory
MC33XX–G
Premium +
WLAN: IEEE
®
802.11a/b/g/n/ac/d
4.0” color 4 GB RAM /
32 GB Flash
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
MC33XX–R
Standard
WLAN: IEEE
802.11a/b/g/n/ac/d
®
4.0” color 2 GB RAM /
16 GB Flash
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
MC33XX–R
Premium
WLAN: IEEE
®
802.11a/b/g/n/ac/d
4.0” color 4 GB RAM /
16 GB Flash
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
Data Capture
Options
SE965 1D,
SE4750-SR 2D,
Operating
System
Android-based
AOSP/GMS 7.1.2
SE4850-ER 2D
SE965 1D Android-based
AOSP/GMS 7.1.2
SE965 1D Android-based
AOSP/GMS 7.1.2
MC33XX–R
Premium +
MC33XX–S
Standard
WLAN: IEEE
®
802.11a/b/g/n/ac/d
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
WLAN: IEEE
®
802.11a/b/g/n/ac/d
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
4.0” color 4 GB RAM /
32 GB Flash
4.0” color 2 GB RAM /
16 GB Flash
SE965 1D Android-based
AOSP/GMS 7.1.2
SE965 1D,
SE4750-SR 2D,
Android-based
AOSP/GMS 7.1.2
SE4850-ER 2D
13
Table 1 Configurations (Continued)
About This Guide
Configuration Radios Display Memory
MC33XX–S
Premium
WLAN: IEEE
®
802.11a/b/g/n/ac/d
4.0” color 4 GB RAM /
16 GB Flash
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
MC33XX–S
Premium +
WLAN: IEEE
802.11a/b/g/n/ac/d
®
4.0” color 4 GB RAM /
32 GB Flash
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
MC33XX–S45
Standard
WLAN: IEEE
802.11a/b/g/n/ac/d
®
4.0” color 2 GB RAM /
16 GB Flash
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
Data Capture
Options
SE965 1D,
SE4750-SR 2D,
Operating
System
Android-based
AOSP/GMS 7.1.2
SE4850-ER 2D
SE4750-SR 2D,
SE4850-ER 2D
Android-based
AOSP/GMS 7.1.2
SE4750-SR 2D Android-based
AOSP/GMS 7.1.2
MC33XX–S45
Premium
MC33XX–S45
Premium +
WLAN: IEEE
®
802.11a/b/g/n/ac/d
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
WLAN: IEEE
®
802.11a/b/g/n/ac/d
/h/i/k/r/w
WPAN: Bluetooth
V4.1, V2.1 + EDR
w/ Bluetooth Low
Energy (BLE)
NFC
4.0” color 4 GB RAM /
16 GB Flash
4.0” color 4 GB RAM /
32 GB Flash
SE4750-SR 2D Android-based
AOSP/GMS 7.1.2
SE4750-SR 2D Android-based
AOSP/GMS 7.1.2
14
Software Versions
To determine the current software versions touch > About phone.
• Model – Displays the model number.
• Android version – Displays the operating system version.
• Kernel version – Displays the kernel version number.
• Build number – Displays the software build number.
To determine the device serial number touch > About phone > Status.
• Serial number - Displays the serial number.
Chapter Descriptions
Topics covered in this guide are as follows:
• Getting Started provides information on getting the MC33XX up and running for the first time.
• Using the MC33XX provides basic instructions for using the MC33XX with Android OS, including powering
on and resetting the MC33XX.
• Applications describes the applications installed on the device.
• Data Capture provides information for capturing barcode data using the internal scanner and optional scan
modules and Bluetooth scanner.
• Wireless provides information on the various wireless options.
• Accessories describes the available accessories and how to use them with the MC33XX.
• Maintenance and Troubleshooting includes instructions on cleaning and storing the MC33XX, and
provides troubleshooting solutions for potential problems during MC33XX operation.
• Technical Specifications provides the technical specifications for the MC33XX.
• MC33XX Keypads provides keypad descriptions and special character generation tables.
About This Guide
Notational Conventions
The following conventions are used in this document:
• Bold text is used to highlight the following:
• Dialog box, window and screen names
• Drop-down list and list box names
• Check box and radio button names
• Icons on a screen
• Key names on a keypad
• Button names on a screen.
15
• Bullets (•) indicate:
• Action items
• Lists of alternatives
• Lists of required steps that are not necessarily sequential.
• Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists.
Icon Conventions
The documentation set is designed to give the reader more visual clues. The following graphic icons are used
throughout the documentation set. These icons and their associated meanings are described below.
NOTE: NOTE contains information more important than the surrounding text, such as exceptions or
preconditions. They also refer the reader elsewhere for additional information, remind the reader how to
complete an action (when it is not part of the current procedure, for instance), or tell the reader where
something is located on the screen. There is no warning level associated with a note.
CAUTION: The word CAUTION with the associated safety icon implies information that, if disregarded, may
About This Guide
result in minor or moderate injury, or serious product damage.
WARNING: The word WARNING with the associated safety icon implies information that, if disregarded,
Related Documents
• MC33XX Mobile Computer Quick Start Guide for Android 7.1.2 Nougat, p/n MN-003143-XX
• MC33XX Regulatory Guide, p/n MN-003144-XX
• MC33XX Mobile Computer Integrator Guide for Android 7.1.2 Nougat, p/n MN-003136-XX
For the latest version of this guide and all guides, go to: http://www.zebra.com/support
Service Information
If you have a problem with your equipment, contact Zebra Support Center for your region. Contact information is
available at: http://www.zebra.com/support
When contacting the Zebra Support Center, please have the following information available:
• Serial number of the unit (found on manufacturing label)
• Model number or product name (found on manufacturing label)
• Software type and version number
could result in death or serious injury, or serious product damage.
.
.
16
Figure 1 Manufacturing Label Location
Manufacturing Label
MC33XX-G
MC33XX-R/S
About This Guide
Zebra responds to calls by email or telephone within the time limits set forth in support agreements.
If your problem cannot be solved by the Zebra Support Center, you may need to return your equipment for
servicing and will be given specific directions. Zebra is not responsible for any damages incurred during shipment if
the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
Remove the microSD card from the device before shipping for service.
If you purchased your product from a Zebra business partner, contact that business partner for support.
Provide Documentation Feedback
If you have comments, questions, or suggestions about this guide, send an email to EVM-Techdocs@zebra.com.
17
Getting Started
1
2
9
8
7
5
3
6
4
Introduction
This chapter provides the features of the MC33XX and explains how to set it up for the first time.
MC33XX-G Features
Figure 2 MC33XX-G Front View
18
Getting Started
Table 2 MC33XX-G Features - Front View
Number Item Function
1 Display Displays all information needed to operate the MC33XX.
2 Charge
/Application
Notification LED
or Scan/Decode
Status
3 Trigger Initiates data capture when a scan application is enabled.
4 Battery Release
Latch
5 Hand Strap Use for securely holding the device.
6 Microphone Use for communications in Handset mode.
7 Power Button Press and hold to turn on the MC33XX. Press to turn on or off the
8 Keypad Use to enter data and navigate on screen functions.
9 Scan Button Initiates data capture when a scan application is enabled.
Indicates the battery charge state while charging, an application
notification was received, or the scan/decode status.
Release the battery from the device.
screen. Press and hold to select one of these options:
Power off - Turn off the MC33XX.
Reboot - Reboot the MC33XX when software stops responding.
Airplane mode - Disable all wireless connections.
Silent mode - All notifications are disabled except for alarms.
19
Figure 3 MC33XX-G Back View
11
10
12
13
14
Getting Started
Table 3 MC33XX-G Features - Back View
Number Item Function
10 Battery Provides power for operating the device.
11 Battery Release
Release the battery from the device.
Latch
12 Speaker Provides audio output for video and music playback.
13 Scanner Exit
Provides data capture using the scanner.
Window
14 NFC Antenna Provides communication with other NFC-enabled devices.
20
MC33XX-R Features
1
2
3
4
5
6
7
8
9
Figure 4 MC33XX-R Front View
Getting Started
Table 4 MC33XX-R Features - Front View
Number Item Function
1 Rotating Turret Rotates for easy scanning positions.
2 Display Displays all information needed to operate the MC33XX-R.
3 Charge
/Application
Notification LED
or Scan/Decode
Status
4 Side Key Scan
Button
5 Battery Release
Latch
6 Power Button Press and hold to turn on the MC33XX-R. Press to turn on or off the
Indicates the battery charge state while charging, an application
notification was received, or the scan/decode status.
Initiates data capture when a scan application is enabled.
Release the battery from the device.
screen. Press and hold to select one of these options:
Power off - Turn off the MC33XX-R.
Reboot - Reboot the MC33XX-R when software stops responding.
Airplane mode - Disable all wireless connections.
Silent mode - All notifications are disabled except for alarms.
21
Getting Started
10
11
12
13
14
15
16
17
18
Table 4 MC33XX-R Features - Front View (Continued)
Number Item Function
7 Microphone Use for communications in Handset mode.
8 Keypad Use to enter data and navigate on screen functions.
9 Scan Button Initiates data capture when a scan application is enabled.
Figure 5 MC33XX-R Back View
Table 5 MC33XX-R Features - Back View
Number Item Function
10 Battery Provides power for operating the device.
11 Battery Release
Release the battery from the device.
Latch
12 Side Key Scan
Button
Initiates data capture when a scan application is enabled.
13 Speaker Provides audio output for video and music playback.
14 Audio Jack Connects to headsets (2.5 mm jack).
15 Scanner Exit
Provides data capture using the scanner.
Window
22
Getting Started
Position Stop
Position Stop
Position Stop
Table 5 MC33XX-R Features - Back View (Continued)
Number Item Function
16 NFC Antenna Provides communication with other NFC-enabled devices.
17 Camera/Flash Provides illumination for the camera.
18 Hand Strap Use for securely holding the device.
Rotating Scan Turret
The MC33XX-R features a Rotating Turret with three position stops. This feature offers greater scanning flexibility.
CAUTION Do not try to rotate the turret past the side position stops. Damage to device may occur.
Figure 6 MC33XX-R Rotating Turret
23
MC33XX-S Features
1
2
3
4
5
6
7
8
Figure 7 MC33XX-S Front View
Getting Started
Table 6 MC33XX-S Features - Front View
Number Item Function
1 Display Displays all information needed to operate the MC33XX-S.
2 Charge
/Application
Notification LED
or Scan/Decode
Status
3 Side Key Scan
Button
4 Battery Release
Latch
5 Power Button Press and hold to turn on the MC33XX-S. Press to turn on or off the
6 Microphone Use for communications in Handset mode.
Indicates the battery charge state while charging, an application
notification was received, or the scan/decode status.
Initiates data capture when a scan application is enabled.
Release the battery from the device.
screen. Press and hold to select one of these options:
Power off - Turn off the MC33XX-S.
Reboot - Reboot the MC33XX-S when software stops responding.
Airplane mode - Disable all wireless connections.
Silent mode - All notifications are disabled except for alarms.
24
Getting Started
9
10
11
12
13
14
15
16
17
Table 6 MC33XX-S Features - Front View (Continued)
Number Item Function
7 Keypad Use to enter data and navigate on screen functions.
8 Scan Button Initiates data capture when a scan application is enabled.
Figure 8 MC33XX-S Back View
Number Item Function
9 Battery Provides power for operating the device.
Table 7 MC33XX-S Features - Back View
10 Battery Release
Latch
11 Side Key Scan
Release the battery from the device.
Initiates data capture when a scan application is enabled.
Button
12 Speaker Provides audio output for video and music playback.
13 Audio Jack Connects to headsets (2.5 mm jack).
14 Scanner Exit
Window
Provides data capture using the scanner.
15 NFC Antenna Provides communication with other NFC-enabled devices.
25
Table 7 MC33XX-S Features - Back View (Continued)
Number Item Function
16 Camera/Flash Provides illumination for the camera.
17 Hand Strap Use for securely holding the device.
Unpacking
Carefully remove all protective material from the MC33XX and save the shipping container for later storage and
shipping.
Verify the following items are in the box:
• MC33XX
• Lithium-ion battery
• Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Zebra Support Center
immediately. See Service Information on page 16 for contact information.
Getting Started
Setup
To start using the MC33XX for the first time:
• Install a microSD card (optional)
• Install the battery
• Charge the MC33XX
• Power on the MC33XX.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack. Refer to the
documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
CAUTION: Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card.
1. Using a coin or finger, remove the microSD card cover.
Figure 9 Remove microSD Card Cover
Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that
the operator is properly grounded.
26
Getting Started
2. Slide the microSD card holder to the Open position.
Figure 10 Unlock microSD Card Holder
3. Lift the microSD card holder.
Figure 11 Lift microSD Card Holder
4. Place the microSD card into the contact area with the contacts facing down.
Figure 12 Install microSD Card
5. Close the microSD card holder and slide the microSD card holder to the Lock position.
Figure 13 Lock microSD Card Holder
6. Replace the microSD card cover and ensure that it is installed properly.
27
Figure 14 Replace Cover
Getting Started
28
Getting Started
Installing the MC33XX-G Battery
The MC33XX-G is compatible with the following batteries:
• MC33XX 5200 mAh PowerPrecision+ extended battery.
• MC32N0 5200 mAh PowerPrecision extended battery.
To install the battery:
1. Loosen the hand strap, if needed.
2. Align the battery into the battery compartment.
Figure 15 Inserting the Battery
3. Rotate the bottom of the battery into the battery compartment.
4. Press battery down firmly. Ensure that both battery release buttons on the sides of the MC33XX-G return to the
home position.
29
Getting Started
Figure 16 Press Battery Down
5. Tighten the hand strap, if needed.
6. Press the Power button to turn on the device.
Installing the MC33XX-R/S Battery
The MC33XX-R/S is compatible with the following batteries:
• MC33XX 2740 mAh PowerPrecision+ standard battery.
• MC33XX 5200 mAh PowerPrecision+ extended battery.
• MC32N0 2740 mAh PowerPrecision standard battery.
• MC32N0 5200 mAh PowerPrecision extended battery.
To install the battery:
1. Loosen the hand strap, if needed.
2. Align the top of the battery into the battery compartment.
Figure 17 Inserting the Battery
30
Getting Started
3. Rotate the bottom of the battery into the battery compartment.
4. Press battery down firmly. Ensure that both battery release buttons on the sides of the MC33XX-R/S return to
the home position.
Figure 18 Press Battery Down
5. Tighten the hand strap, if needed.
6. Press the Power button to turn on the device.
Charging the Battery
CAUTION:Ensure that you follow the guidelines for battery safety described in Battery Safety Guidelines on
page 199.
Use the mobile computer cradles, cables and spare battery chargers to charge the mobile computer main battery.
The main battery can be charged before insertion into the mobile computer or after it is installed. There are two
main batteries for the MC33XX, the 2740 mAh PowerPrecision+ standard battery (1X) and the 5200 mAh
PowerPrecision+ extended battery (2X). The MC33XX-G is compatible with the 5200 mAh PowerPrecision+
extended battery. The MC33XX-R/S are compatible with both the 2740 mAh PowerPrecision+ standard battery
and the 5200 mAh PowerPrecision+ extended battery. Use one of the spare battery chargers to charge the main
battery (out of the mobile computer) or one of the cradles to charge the main battery while it is installed in the
mobile computer.
Before using the mobile computer for the first time, fully charge the main battery until the green Charge LED
indicator remains lit and charge the battery using a cable or a cradle with the appropriate power supply. For
information about the accessories available for the MC33XX, see Accessories. The 2740 mAh PowerPrecision+
standard battery fully charges (0% to 90% capacity) in less than 2.2 hours and the 5200 mAh PowerPrecision+
extended battery fully charges (0% to 90% capacity) in less than 3.8 hours.
The MC33XX retains data in memory for at least five minutes when the mobile computer’s main battery is
removed.
When the main battery reaches a very low battery state, the battery retains data in memory for at least 15 hours.
Batteries must be charged within the 0° to +40° C (32° to 104° F) ambient temperature range.
The following accessories can be used to charge batteries:
31
Getting Started
• Cradles (and a power supply):
• 1-Slot USB Charge Cradle
• 5-Slot Charge Only ShareCradle
• 5-Slot Ethernet ShareCradle
• 5-Slot Charge ShareCradle + 4-Slot Spare Battery Charger
• 5-Slot Ethernet ShareCradle + 4-Slot Spare Battery Charger.
• Cables (and a power supply):
• USB Charge Cable.
• Spare Battery Chargers (and a power supply):
• 4-Slot Spare Battery Charger
• 20-Slot Spare Battery Charger.
To charge the mobile computer using the cradles:
1. Insert the mobile computer into a cradle. See Accessories for accessory setup.
2. The mobile computer starts to charge automatically. The Charge LED Indicator indicates the charge status. See
the table below for charging indications.
To charge the mobile computer using the cables:
1. Connect the MC33XX Communication/Charge Cable to the appropriate power source and connect to the mobile
computer. See Accessories for accessory setup.
2. The mobile computer starts to charge automatically. The Charge LED Indicator indicates the charge status.
Table 8 LED Charge Indicators
Status Indications
Off • The battery is not charging.
• The battery is not inserted correctly in the cradle or connected to a
power source.
• Cradle is not powered.
Slow Blinking Amber
Every 3 seconds
Solid Amber • Battery is charging.
Solid Green • Battery charging is complete.
Fast Blinking Red
2 blinks/second
• Battery is charging, but the battery is fully depleted and does not yet
have sufficient charge to power the device.
Charging error, e.g.:
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight
hours).
Solid Red • Spare battery is charging and battery is at the end of useful life.
• Charging complete and battery is at the end of useful life.
The MC33XX 2740 mAh PowerPrecision+ standard battery charges from 0% to 90% in less than 2.2 hours at room
temperature.
32
Getting Started
The MC33XX 5200 mAh PowerPrecision+ extended battery charges from 0% to 90% in less than 3.8 hours at
room temperature.
The MC32N0 2740 mAh PowerPrecision standard battery charges from 0% to 90% in less than 3 hours at room
temperature.
The MC32N0 5200 mAh PowerPrecision extended battery charges from 0% to 90% in less than 5.5 hours at room
temperature.
Backup Power
The MC33XX is equipped with a supercapcitator (supercap) to provide backup power to the device when the main
battery is removed. The supercap will retain random access memory (RAM) data in memory for approximately five
minutes after the main battery is removed during Hot Swap.
IMPORTANT: The supercap is automatically charged from the main battery and requires approximately ten
minutes to fully charge.
Charging Temperature
Charge batteries in ambient temperatures from 0°C to 40°C (32°F to 104°F) or up to 45°C (113°F) as reported by
the battery. To view battery temperature, touch > About phone > Battery information.
Note that charging is intelligently controlled by the MC33XX. To accomplish this, for small periods of time, the
MC33XX or accessory alternately enables and disables battery charging to keep the battery at acceptable
temperatures. The MC33XX or accessory indicates when charging is disabled due to abnormal temperatures via
its LED.
Charging Spare Batteries
See Accessories for information on using accessories to charge spare batteries.
Hot Swap Mode
The MC33XX provides a Hot Swap mode where the user can replace the battery without powering off the device.
When the user removes the battery, the display turns off and the device enters a low power state while in Hot Swap
mode. In Hot Swap mode, the MC33XX retains RAM data for approximately five minutes. Replace the battery
within five minutes to preserve memory persistence. If the user does not install a charged battery within five
minutes, data in RAM will be lost. During Hot Swap mode, Wi-Fi and Bluetooth remain connected for 30 seconds.
If the battery is not inserted within 30 seconds, Wi-Fi is disabled and then re-enabled when the device comes out of
Hot Swap mode and Bluetooth is reset when the device comes out of Hot Swap mode.
IMPORTANT: The supercap requires time to recharge after performing a Hot Swap or after the main battery is
fully depleted. Hot Swap mode will not retain data unless the supercap is fully charged.
Google Account Setup
NOTE: The MC33XX has to be connected to the internet in-order to set up a Google ™ account.
Google account only required on devices with GMS software.
33
Getting Started
The first time the MC33XX starts, the Setup Wizard displays. Follow the on-screen instructions to set up a Google
account, configure Google Wallet for purchasing items from the Play Store, entering your personal information, and
enabling backup/restore features.
Replacing the Battery in the MC33XX-G
1. Push in the two Battery Release buttons.
The battery ejects slightly. With Hot Swap mode, when the user removes the battery, the display turns off and
the device enters a low power state. The MC33XX-G retains RAM data for approximately five minutes.
Replace the battery within five minutes to preserve memory persistence.
Figure 19 Release Battery
2. Remove the battery from the battery compartment.
34
Figure 20 Remove Battery
Getting Started
3. Align the battery into the battery compartment.
Figure 21 Inserting the Battery
4. Rotate the bottom of the battery into the battery compartment.
35
Getting Started
5. Press battery down firmly. Ensure that both battery release buttons on the sides of the MC33XX-G return to the
home position.
Figure 22 Press Battery Down
6. Press the Power button to turn on the device.
Replacing the Battery in the MC33XX-R/S
7. Push in the two Battery Release buttons.
The battery ejects slightly. With Hot Swap mode, when the user removes the battery, the display turns off and
the device enters a low power state. The MC33XX-R/S retains RAM data for approximately five minutes.
Replace the battery within five minutes to preserve memory persistence.
Figure 23 Release Battery
8. Remove the battery from the battery compartment.
36
Figure 24 Remove Battery
Getting Started
9. Align the battery into the battery compartment.
Figure 25 Inserting the Battery
10. Rotate the bottom of the battery into the battery compartment.
11. Press battery down firmly. Ensure that both battery release buttons on the sides of the MC33XX-R/S return to
the home position.
37
Figure 26 Press Battery Down
12. Press the Power button to turn on the device.
Accessing Device Settings
Throughout this guide, the user can access device settings:
Getting Started
1. Swipe down from the status bar and then touch .
2. On the Home screen, swipe up from the bottom of the screen and touch .
Battery Management
NOTE: Prior to checking the battery charge level, remove the MC33XX from any AC power source (cradle
or cable).
To check the charge status of the main battery, touch > About phone > Status.
Battery status indicates that the battery is discharging and Battery level lists the battery charge (as a percentage
of fully charged).
IMPORTANT: At temperatures below 0°C, the Battery Charge Level may report a reduced value. This is normal
due to temperature compensation.
Monitor Battery Usage
The Battery screen lists which applications consume the most battery power. Also use it to turn off applications
that were downloaded if they are consuming too much power.
Touch > Battery or swipe down from the status bar and then touch .
38
Getting Started
Figure 27 Battery Screen
The Battery screen lists the applications using the battery. The discharge graph at the top of the screen shows the
rate of the battery discharge since last charged (short periods of time when connected to a charger are shown as
thin green lines at the bottom of the chart), and how long it has been running on battery power.
Touch an application in the Battery screen to display details about its power consumption. Different applications
display different information. Some applications include buttons that open screens with settings to adjust power
use.
Low Battery Notification
When the battery charge drops below 23% (MC33XX 2740 mAh PowerPrecision+ standard battery) or 15%
(MC33XX 5200 mAh PowerPrecision+ extended battery) to a low level, the MC33XX displays a notice to connect
the MC33XX to power. The user should charge the battery using one of the charging accessories.
When the battery charge drops below 15% (MC33XX 2740 mAh PowerPrecision+ standard battery) or 8%
(MC33XX 5200 mAh PowerPrecision+ extended battery) to a very low level, the MC33XX displays a notice to
connect the MC33XX to power. The user should charge the battery using one of the charging accessories.
When the battery charge drops below 8% (MC33XX 2740 mAh PowerPrecision+ standard battery) or 4%
(MC33XX 5200 mAh PowerPrecision+ extended battery), the MC33XX goes into critical suspend mode to save
data. The screen turns off.
The user must replace the battery or charge the MC33XX using one of the charging accessories to retain data.
Battery Optimization
Observe the following battery saving tips:
• Leave the MC33XX connected to AC power at all times when not in use.
• Disable DataWedge Launcher profile. Refer to the MC33XX Mobile Computer Integrator Guide for
instructions.
• Set the screen to turn off after a short period of non-use. See Changing the Screen Timeout Setting on
page 41.
• Set the MC33XX to turn off when not in use. See Resetting the Device on page 70.
• Reduce the screen brightness. See Setting the Screen Brightness on page 41.
• Turn off all wireless radios when not in use.
39
• Turn off automatic syncing for Email, Calendar, Contacts, and other applications.
• Minimize use of applications that keep the MC33XX from suspending, for example, music and video
applications.
Turning Off the Radios
To turn off all the radios:
1. Press the Power button until the menu appears.
2. Touch Airplane mode. The airplane icon appears in the Status bar indicating that all the radios are off.
Connecting a Wired Headset
To connect a wired headset to the MC33XX-R/S:
Figure 28 Connect Headset to MC33XX–R/S
Getting Started
Real-Time Clock Backup
The MC33XX provides a Real-time Clock (RTC) backup feature. After boot-up, the device saves the system time in
a file in persistent storage. When the device re-boots, it compares the system time to the time saved in a file. If the
system time in not the latest, it restores the time from the file.
Setting the Date and Time
The user is only required to set the time zone or set the date and time when not connected to a wireless network.
1. Swipe down from the status bar and then touch .
2. Touch Date & time.
3. Touch Automatic date & time to disable automatic date and time synchronization.
4. Touch Set date.
5. In the calendar, set today’s date.
6. Touch OK.
7. Touch Set time.
8. Touch the green circle, drag to the current hour and then release.
9. Touch the green circle, drag to the current minute and then release.
40
10. Touch AM or PM.
11. Touch OK.
12. Touch Automatic time zone to disable automatic date and time synchronization.
13. Touch Select time zone.
14. Select the current time zone from the list.
15. Touch .
Display Setting
Use Display settings to change the screen brightness, change the background image, enable screen rotation, set
sleep time and change font size.
Setting the Screen Brightness
To manually set the screen brightness:
1. Swipe down from the status bar to open the quick access panel.
2. Slide the icon to adjust the screen brightness level.
Getting Started
Figure 29 Brightness Slider
Changing the Screen Timeout Setting
To set the screen sleep time:
1. Swipe down from the status bar and then touch .
2. Touch Display.
3. Touch Sleep
4. Select one of the sleep values.
• 15 seconds
• 30 seconds
• 1 minute (default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes
5. Touch .
Setting Font Size
To set the size of the font in system applications:
1. Swipe down from the status bar and then touch .
41
2. Touch Display.
3. Touch Font Size.
Figure 30 Font Settings
Getting Started
4. Select one of the font size values.
• Small
• Default (default)
• Large
• Largest.
5. Touch .
Setting Screen Rotation
By default, screen rotation is disabled. To enable screen rotation:
1. Swipe down from the status bar and then touch .
2. Touch Display.
3. Touch When device is rotated and select Rotate the contents of the screen to set the MC33XX to
automatically switch orientation when the MC33XX is rotated.
4. Touch .
Touch Panel Mode
The MC33XX display is able to detect touches using a glove and finger or a stylus and finger.
NOTE: A glove can be made of medical latex, leather, cotton or wool.
For optimal performance use Zebra certified stylus.
1. Swipe down from the status bar and then touch .
2. Touch Display.
42
3. Touch Touch panel mode.
4. Touch Glove and Finger to use a finger or a gloved finger on the screen or touch Stylus and Finger to use a
finger or a stylus on the screen.
Figure 31 Screen Protector Mode Dialog Box
5. Touch .
General Sound Setting
Getting Started
Use the Sounds settings to configure media and alarm volumes.
1. Swipe down from the status bar and then touch .
2. Touch Sound.
Figure 32 Sound Screen
• Zebra volume controls
• Ring volume - Controls the ringtone volume.
• Media volume - Controls the music, games and media volume.
• Alarm volume - Controls the alarm clock volume.
• Notification volume - Controls the notification volume.
• Scanner volume - Controls the scanner volume.
• Volume Presets
43
Getting Started
• - Mutes the ring, notifications and scanner so that the MC33XX does not make sounds or
vibrate.
• - Enables all sounds at the user defined levels.
• Do not disturb - Mutes the MC33XX so that it does not make sounds or vibrate when you do not want it to.
• Priority only allows - Use to set priorities.
• Alarms - Disabled.
• Reminders and Events - Switch on or off.
• Messages - Choose from anyone, from contacts only, from starred contacts only or none. To star
contacts, use the Contacts app.
• Repeat callers - Choose whether to let the MC33XX ring if the same person calls again within 15
minutes.
• Automatic rules - To automatically silence the MC33XX during certain times, like at night or on
weekends. Touch a default rule Weekend or Weeknight. Or, to make your own rule, tap Add rule and
then Time rule.
• Block visual disturbances
• Block when screen is on - option pertains to notifications you receive when you are actively
using the device. If you would like to disable the banner like notifications when Do not Disturb is
enabled, turn this option On. This will also prevent you from peeking at notifications.
• Block when screen is off - option pertains to notifications you receive when you are not using
your device i.e. the display is asleep. If you want to prevent the display from waking up when a
new notification is received, turn this option On. This will additionally disable the LED light alerts
your phone sends you when you have new notifications.
• Default notification ringtone - Touch to select a sound to play for all system notifications.
• Default alarm ringtone - Touch to select a sound to play for alarms.
• Other sounds
• Screen locking sounds - play a sound when locking and unlocking the screen (default – enabled)
• Charging sounds - Not applicable.
• Touch sounds - Play a sound when making screen selections (default – enabled).
Wake-Up Sources
By default, the MC33XX wakes from suspend mode when the user presses the power button. The MC33XX can be
configured to wake when the user presses the Trigger or the Scan button.
1. Swipe down from the status bar and then touch .
2. Touch Wake-Up Sources.
44
Getting Started
Figure 33 Wake-Up Sources
3. Touch SCAN checkbox. A check appears in the checkbox.
4. Touch GRIP_TRIGGER checkbox. A check appears in the checkbox.
5. Touch .
45
Using the MC33XX
Introduction
This chapter describes the screens, status and notification icons, and controls on the MC33XX, and provides basic
instructions for using the MC33XX.
Google Mobile Services
NOTE This section only applies to MC33XX devices with Google Mobile Services (GMS) software.
The MC33XX with GMS contains applications and services that provide additional functionality to the MC33XX.
GMS includes:
• Applications - GMS adds a variety of Google applications and associated widgets including Chrome,
Gmail, Drive and Maps.
• Services:
• Speech to Text - Allows for free format speech to text, in many languages for both connected and
disconnected network. Launch by touching the microphone icon on the keyboard.
• TalkBack Service - Provides spoken feedback on various parts of the user interface. To enable, go to
Settings > Accessibility.
• Network Location Provider - Adds a location provider which uses mobile network tower information
and Wi-Fi access point information to provide a location without using GPS. To enable, go to Settings
> Location access.
• Widevine DRM - Enables the digital rights management so that protected content can be played.
Enable via DRM Info from the Play Store.
• Google Cloud Messaging - Allows the sending of data from your server to your MC33XX and also to
receive messages from devices on the same connection.
• Backup and Restore - Allows the users settings and applications to be backed up to a Google server
and subsequently restored from that server after a factory reset.
• Google accounts - Create and use a Google account to synchronize mail, files, music, photos, contacts
and calendar events.
46
Home Screen
1
2
3
4
5
6
7
8
9
GMS
AOSP
The Home screen displays when the MC33XX turns on. Depending upon the configuration, the Home screen might
appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock sliders. Touch the screen and slide up
to unlock. For screen locking information see Un-Locking the Screen on page 68.
Figure 34 Home Screen
Using the MC33
NOTE: The Home screen icons can be configured by the user and may look different than shown.
The Home screen consists of the following:
Table 9 Home Screen Items
Item Description
1 — Status Bar Displays the time, status icons (right side), and notification icons (left side). For more
information see on page 48 and Managing Notifications on page 51.
2 — Widgets Launches stand-alone applications that run on the Home screen. See Application Shortcuts
and Widgets on page 54 for more information.
3 — Shortcut
Icons
4 — Folder Contains apps.
5 — Settings Icon Opens the Settings window.
6 — Back Displays the previous screen.
Opens applications installed on the MC33XX. See Application Shortcuts and Widgets on
page 54 for more information.
7 — Home Displays the Home screen.
47
Table 9 Home Screen Items (Continued)
Notifications icons
Status icons
Item Description
Using the MC33
8 — Recent
Button
9 — All Apps Icon Opens the APPS window.
The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left or
right to view the additional screens.
Displays recently used applications.
Setting Home Screen Rotation
By default, the Home screen rotation is disabled. To enable Home screen rotation:
1. Touch and hold anywhere on the Home screen until the options appear.
2. Touch .
3. Touch Allow Home screen rotation switch.
4. Touch .
5. Rotate the device.
Figure 35 Rotated Home Screen
Status Bar
The Status bar displays the notification icons (left side), time and status icons (right side).
NOTE: Some status icons may not appear in the Status Bar if there are too many icons to display.
Figure 36 Notification and Status Icons
If there are more notifications than can fit in the Status bar, displays indicating that more notifications exist.
Open the Notifications panel to view all notifications and status.
48
Using the MC33
Status Icons
Table 10 Status Icons
Icon Description
Indicates that all sounds except media and alarms are silenced.
Indicates that the Orange key is locked.
Indicates that the Blue key is pressed.
Indicates that the ALT key is pressed.
Indicates that the CTRL key is pressed.
Indicates that the Shift key is pressed.
Indicates that the Shift key is locked.
Indicates that a BT headset is connected to the MC33XX.
Indicates that the Alarm is active.
Indicates that the main battery is fully charged.
Indicates that the main battery is partially drained.
Indicates that the main battery charge is low.
Indicates that the main battery charge is very low.
Indicates that the main battery is charging.
Indicates that the Airplane Mode is active. All radios are turned off.
Indicates that Bluetooth is on.
Indicates that the MC33XX is connected to a Bluetooth device.
Connected to a Wi-Fi network.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Portable Wi-Fi Hotspot is active.
49
Using the MC33
Notification Icons
Table 11 Notification Icons
Icon Description
Indicates that the internal storage disc is almost full.
Screenshot captured.
Error capturing screenshot.
Indicates the status of the PTT Express Voice Client. For a complete list of PTT Express
notification icons see Table 16 on page 97
Indicates that more notifications are available for viewing.
Indicates that data is syncing.
Indicates an upcoming event.
Indicates that an open Wi-Fi network is available.
Indicates that a song is playing.
Indicates that a problem with sign-in or sync has occurred.
Indicates that the MC33XX is uploading data.
Indicates that the MC33XX is downloading data when animated and download is complete
when static.
Indicates that USB tethering is active.
Indicates that the MC33XX is connected to or disconnected from virtual private network (VPN).
Preparing Internal Storage.
Indicates that USB debugging is enabled on the MC33XX.
Headset is connected to device.
Indicates the status of the PTT Express Voice Client. See Notification Icons for complete list of
PTT Express notification icons.
Indicates that RxLogger application is running.
Indicates a Bluetooth scanner is connected to the MC33XX.
50
Using the MC33
Managing Notifications
Notification icons report the arrival of new messages, calendar events, and alarms, as well as ongoing events.
When a notification occurs, an icon appears in the Status bar with a brief description. See Notification Icons on
page 50 for a list of possible notification icons and their description. Open the Notifications panel to view a list of
all the notifications.
To open the Notification panel, drag the Status bar down from the top of the screen.
Figure 37 Notification Panel
To respond to a notification, open the Notifications Panel and then touch a notification. The Notifications Panel
closes and the subsequent activity is dependent on the notification.
To clear all notifications, open the Notifications Panel and then touch CLEAR ALL. All event-based notifications
disappear. Ongoing notifications remain in the list.
To close the Notification Panel, swipe the Notifications Panel up.
Setting Application Notifications
To change notification settings for a specific app:
1. Swipe down from the status bar and then touch .
2. Touch Notifications.
3. Select an app.
4. Select an available option:
• Block all
• Show silently
• Override Do Not Disturb.
IMPORTANT In the notification, slide the notification slightly left or right and touch .
Viewing Notification Settings for All Apps
1. Swipe down from the status bar and then touch .
2. Touch Notifications.
3. Touch down-arrow next to All apps.
4. To see all the apps currently set to a specific setting, touch that setting.
Controlling Lock Screen Notifications
To control notification content on the lock screen:
1. Swipe down from the status bar and then touch .
51
Using the MC33
2. Touch Notifications > .
3. Touch On the lock screen.
4. Select Show all notification content to or select Don’t show notifications at all.
Pulse Notification Light
The Notification LED lights blue when an app, such as email and VoIP, generates a programmable notification
or to indicate when the device is connected to a Bluetooth device. By default, LED notifications are enabled.
To change the notification setting:
1. Swipe down from the Status bar to open the Quick Settings bar and then touch .
2. Touch Notifications > .
3. Touch Pulse notification light to toggle the notification on or off.
Quick Access Panel
Use Quick Settings to get to frequently used settings, like turning on airplane mode. To open the Quick Settings
bar, swipe down once from the top of an unlocked screen.
Figure 38 Quick Settings Bar
To see the full Quick Settings panel:
• If the MC33XX is locked, swipe down once.
• If the MC33XX is unlocked, swipe down once with two fingers, or twice with one finger.
• If the Quick Settings bar is open, touch the Down arrow.
Figure 39 Full Quick Settings
Available setting tiles:
• Display brightness: Slide to lower or increase the brightness of the screen.
• Wi-Fi network: Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
• Battery Power - Indicates percentage of battery power remaining. Touch to view battery usage.
52
Using the MC33
• Do not disturb: Control how and when to receive notifications.
• Flashlight: Turn camera flash on or off.
The thermal protection safety feature for the camera provides the following behavior if the temperature
range is 40°C or above:
• If the flashlight is kept on for a certain period of time, it is automatically turned off and cannot be turned
back on for a period of time until it has cooled off.
• During the cooling off period, the camera cannot be turned on. If the user attempts to use the camera,
a message displays indicating to try again after a period of time.
• Auto-rotate: Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
• Bluetooth settings: Turn Bluetooth on or off. To open Bluetooth settings, touch the Bluetooth.
• Airplane mode: Turn airplane mode on or off. Airplane mode means device will not connect to Wi-Fi or
Bluetooth.
• Location - Turn locationing on or off.
• Invert colors - Invert the display colors.
• Data Saver - Turn on to prevent some apps from sending or receiving data in the background.
• Night Light - Tint the screen amber to make it easier to look at the screen in dim light. Set Night Light to
turn on automatically from sunset to sunrise, or at other times.
• Nearby - Helps find and interact with services and devices close to the device.
Edit Icons on Quick Settings
The first several setting tiles become the Quick Settings bar.
To move a setting tile:
1. Touch and drag a setting tile to another location.
2. Release the tile.
3. Touch to save tiles and return to quick settings.
To add a setting tile:
1. Open Quick Settings.
2. Touch .
3. Slide Quick Settings panel up to reveal additional tiles.
4. Touch and drag a setting tile from the Drag to add tiles area to the main area.
5. Release the tile.
6. Touch to save tiles and return to quick settings.
To remove a setting tile:
1. Open Quick Settings.
2. Touch .
3. Touch and drag a setting tile to the Drag here to remove area.
4. Release the tile.
5. Touch to save tiles and return to quick settings.
53
Using the MC33
Application Shortcuts and Widgets
Application shortcuts placed on the Home screen allow quick and easy access to applications. Widgets are
self-contained applications placed on the Home screen to access frequently used features.
Adding an Application to the Home Screen
1. Go to the desired Home screen.
2. Swipe up from the bottom of the screen.
3. Scroll through the list to find the application icon.
4. Touch and hold the icon until the Home screen appears.
5. Position the icon on the screen and then release.
Adding a Widget to the Home Screen
To add a widget to the Home screen:
1. Go to the desired Home screen.
2. Touch and hold until the menu appears.
3. Touch WIDGETS.
4. Scroll through the list to find the widget.
5. Touch and hold the widget until the Home screen appears.
6. Position the widget on the screen and then release.
Moving Items on the Home Screen
1. Touch and hold the item until it floats on the screen.
2. Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home
screen.
3. Lift finger to place the item on the Home screen.
Removing an Application Shortcut or Widget from the Home Screen
1. Go to the desired Home screen.
2. Touch and hold the application shortcut or widget icon until it floats on the screen.
3. Drag the icon to on the top of the screen and then release.
Folders
Use Folders to organize similar applications together. Tap the folder to open and display items in the folder.
Creating Folders
To create a folder, there must be at least two app icons on the Home screen.
1. Go to the desired Home screen.
2. Touch and hold on one application icon.
3. Drag the icon and stack on top of another icon.
4. Lift and release.
54
Using the MC33
Naming Folders
To name a folder:
1. Touch the folder.
Figure 40 Open Folder
2. Touch the title area and enter a folder name using the keyboard.
3. Touch on the keyboard.
4. Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.
Figure 41 Renamed Folder
Removing Folders
To remove a folder:
1. Touch and hold the folder icon until it enlarges.
2. Drag the folder to and release.
Home Screen Wallpaper
To change the Home screen wallpaper.
1. Touch and hold on the screen until the menu appears.
2. Touch WALLPAPERS.
3. Touch My photos to select a photo from Gallery or select one of the pre-installed photos.
4. Touch Save wallpaper.
Using the Touchscreen
Use the multi-tap sensitive screen to operate the device.
55
Using the MC33
• Tap - Tap to:
• select items on the screen
• type letters and symbols using the on-screen keyboard
• press on-screen buttons.
• Tap and Hold - Tap and hold:
• an item on the Home screen to move it to a new location or to the trash.
• an item in Apps to create a shortcut on the Home screen.
• the Home screen to open a menu for customizing the Home screen.
• an empty area on the Home screen until the menu appears.
• Drag - Tap and hold an item for a moment and then move finger on the screen until reaching the new
position.
• Swipe - Move finger up and down or left and right on the screen to:
• unlock the screen
• view additional Home screens
• view additional application icons in the Launcher window
• view more information on an application’s screen.
• Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.
• Pinch - In some applications, zoom in and out by placing two fingers on the screen and pinching them
together (to zoom out) or spreading them apart (to zoom in).
Keyboards
The MC33XX provides the following types of keyboards:
• Android Keyboard - Available on MC33XX with AOSP build.
• Google Keyboard - Available on MC33XX with GMS build.
• Enterprise Keyboard - Available on AOSP and GMS builds, if enabled.
NOTE: By default the Enterprise keyboard is disabled. To enable the Enterprise keyboard, refer to the MC33XX
Mobile Computer Integrator Guide.
To switch between keyboards:
1. Touch in a text box to display the current keyboard.
2. On the Enterprise keyboard, touch or on the Android keyboard, touch .
Keyboard Configuration
To configure the keyboard, refer to the Keyboard Settings section in the MC33XX Mobile Computer Integrator
Guide.
Using the Enterprise Keyboard
The Enterprise Keyboard contains the following keyboards:
56
Using the MC33
• Numeric
• Alpha
• Special characters
• Data capture.
Numberic Tab
To access the numeric keyboard, touch the 123 tab. The keys displayed vary on the application being used. For
example, an arrow displays in Contacts, however Done displays in Email account setup.
Figure 42 Numeric Keyboard
Alpha Tab
To access the alpha keyboard, touch the EN tab.
NOTE: The Enterprise keyboard supports English (US), English (UK), French, German, Spanish and Italian.
When a keyboard language is selected in Settings, the corresponding keyboard language displays.
Figure 43 Alpha Keyboard
Touch to enter emoji icons in a text message.
57
Using the MC33
Figure 44 Emoji Keyboard
Touch ABC to return to the Alpha keyboard.
Additional Character Tab
To access additional characters, touch the #*/ tab.
Figure 45 Symbols Keyboard
Scan Tab
The Scan tab provides an easy data capture feature for scanning barcodes.
Figure 46 Scan Keyboard
Using the Android Keyboard
Use the on-screen keyboard to enter text in a text field. To configure the keyboard settings, touch and hold
(comma) > and then select Android keyboard settings.
58
Using the MC33
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across applications. Some
applications do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols and Special Characters
To enter numbers and symbols:
• Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate
characters display an ellipsis ( ... ) below the character.
• Touch the Shift key once for a single capital letter. Touch the Shift key twice to lock in uppercase. Touch
the Shift key a third time to unlock Capslock.
• Touch to switch to the numbers, symbols keyboard and additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.
• A larger version of the key displays briefly over the keyboard.
• Keys with alternate characters display an ellipsis ( ... ) below the character.
Hiding On-Screen Keyboard
On devices with keypads, the user can hide the on-screen keyboard.
Touch in a text field to display the on-screen keyboard. Touch at the bottom right corner of the screen.
Figure 47 Hide Keyboard Option
Touch the Show virtual keyboard switch to off. The on-screen keyboard automatically disappears.
To show the on-screen keyboard, Touch in a text field. Touch at the bottom right corner of the screen. Touch
the Show virtual keyboard switch to on. The keyboard re-appears.
Switching Language Keyboards
The user can enable multiple language keyboards.
Figure 48 Keyboard with Multiple Languages
To switch between language keyboard, touch at the bottom right corner of the screen.
59
Figure 49 Change Keyboard Option
Select one of the keyboard languages. The keyboard automatically changes to the selected language.
Do Not Disturb Feature
This mode mutes the MC33XX so that it does not make sounds or vibrate.
For example, use Do Not Disturb to:
• Automatically limit sounds at night or during events
• Mute interruptions other than alarms
• Get alerted to messages only from favorite contacts.
Using the MC33
Limit Sounds and Vibrations
Mute the MC33XX completely, or let through the important alarms or important calls.
Total Silence
To completely mute the MC33XX so that it does not make a sound or vibrate, choose Total silence.
In Total silence mode:
• Alarms do not make noise.
• MC33XX does not vibrate or make sounds when receiving a message, or notification.
• Sounds from music, videos, games, and other media are muted.
NOTE: The user will not hear alarms in Total silence mode.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Total silence.
3. Choose Until you turn it off or select a time period.
4. Touch Done.
When Total Silence is on, appears in the quick access panel and the Status Bar.
To turn off Total Silence, open quick access panel and touch Total silence.
Alarms Only
To mute the MC33XX so that the user hears alarms, choose Alarms only. This option does not mute sounds from
music, videos, games, or other media.
60
Using the MC33
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Alarms only.
3. Choose Until you turn it off or select a time period.
4. Tap Done.
When Alarms Only is on, appears in the quick access panel and the Status Bar.
To turn off Alarms Only, open quick access panel and touch Alarms only.
NOTE: To quickly turn on Alarms Only, with the screen on, press and hold the Volume Down button until the
volume is all the way down. Then, press Volume Down again to turn on Alarms Only.
To turn off Alarms Only, press either the Volume Up or Volume Down button and the touch END NOW in the alert
message. Then, press Volume Up again to turn on Alarms Only.
Priority Notifications Only
To only be interrupted by important notifications, choose Priority Only. This option does not mute sounds from
music, videos, games, or other media.
Before turning on Priority Only mode, set the notification priorities:
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Sound > Do not disturb > Priority only allows.
3. Set priorities.
• Alarms: Disabled by default.
• Reminders and Events: Switch on or off.
• Messages and Calls: Choose From anyone, From contacts only, From starred contacts only, or
none. To star contacts, use the Contacts app.
• Repeat callers: Choose whether to let the MC33XX ring if the same person calls again within 15 minutes.
After setting notification priorities, turn on Priority only mode to limit interruptions. The priority notifications make a
sound or vibrate based on the current ringer volume, but other notifications will be silenced.
1. Swipe down with two fingers from the status bar to open the quick access panel.
2. Touch Do not disturb > Priority only.
3. Choose Until you turn it off or select a time period.
4. Tap Done.
When Priority Only is on, appears in the quick access panel and the Status Bar.
To turn off Priority Only, open quick access panel and touch Priority only.
Automatically Block Sounds and Vibrations
Silence Sounds During Certain Times
To automatically silence the MC33XX during certain times, like at night or on weekends, set the time rules.
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
61
Using the MC33
2. Touch Sound > Do not disturb > Automatic rules.
3. Touch a default Weekend or Weeknight. Or, to make a new rule, touch Add rule and then Time rule.
4. Edit the new rule:
• Rule name: Name the rule.
• Days, Start time, and End time: Set the rule's schedule.
• Do not disturb: Choose whether the rule uses Alarms only, Priority only, or Total silence.
5. Touch the On/Off text or switch at the top to turn on the rule.
Silence Sounds During Events and Meetings
To automatically silence the MC33XX during events or meetings, set an event rules.
1. Swipe down with two fingers from the status bar to open the quick access panel and then touch .
2. Touch Sound & notification > Do not disturb > Automatic rules.
3. To edit the default rule, touch Event. Or, to create a new rule, touch Add rule > Event rule.
4. Edit the rule settings.
• During events for: Select which Google Calendar events the rule uses.
• Where reply is: Options: Yes, Maybe, or Not replied, Yes or Maybe, or Yes.
• Do not disturb: Choose whether the rule uses Priority only, Alarms only, or Total silence.
5. Touch the On/Off switch at the top to turn on the rule.
Turn Sounds Back On
When the MC33XX is in Do Not Disturb mode, Alarms or Priority only or Total silence display.
To turn off Do Not Disturb, either:
• In the quick access panel, touch Alarms only, Priority only, or Total silence.
• Press the Volume Down button and touch End Now.
Override Do Not Disturb for Specific Apps
To let through notifications from specific apps:
1. Open Settings > Notifications.
2. Touch an app.
3. Touch Override Do Not Disturb.
Applications
The APPS screen displays icons for all installed applications. The table below lists the applications installed on the
MC33XX. Refer to the MC33XX Integrator Guide
for information on installing and uninstalling applications.
62
Using the MC33
Table 12 Applications
Icon Description
AppGallery - Provides links to utilities and demonstration applications that can be installed on the
MC33XX.
Battery Manager – Displays battery information, including charge level, status, health and wear
level.
Bluetooth Pairing – Use to pair a Bluetooth Imager with the MC33XX by scanning a barcode.
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments.
Camera - Take photos or record videos.
Chrome - Use to access the Internet or intranet. MC33XX with GMS only.
Chromium - An open-source web browser project started by Google, which provides the source
code for the proprietary Google Chrome browser. MC33XX with AOSP only.
Clock - Use to schedule alarms for appointments or as a wake-up.
Contacts - Use to manage contact information. See Contacts on page 78 for more information.
DataWedge - Enables data capture using the camera, scanner or imager.
Device Central - Displays detailed information about the MC33XX and supported peripherals. See
Device Central for more information.
Diagnostic Tool - Use to diagnose the MC33XX. See Diagnostic Tool for more information.
Downloads - lists all downloads files.
Drive - Upload photos, videos, documents, and other files to personal storage site. MC33XX with
GMS only.
63
Using the MC33
Table 12 Applications (Continued)
Icon Description
DWDemo - Provides a way to demonstrate the data capture features using the Linear Imager. See
DataWedge Demonstration on page 94 for more information.
Email - Use to send and receive email.
File Browser - Organize and manage files on the MC33XX. See File Browser on page 76 for more
information.
Gallery - Use to view photos stored on the microSD card. For more information, see Gallery.
MC33XX with AOSP only.
Gmail - Use to send and receive email using a Google email account. MC33XX with GMS only.
Google - Launches Google search application. MC33XX with GMS only.
Hangouts - Use to communicate with friends using text messages and photos. MC33XX with GMS
only.
License Manager - Use to manage software licenses on the MC33XX.
Maps - Use to see your location on a map (with public transit, traffic or satellite overlays). Search
for any business or place of interest. Provides turn-by-turn navigation with voice guidance and
traffic-avoidance and alternate routes, for drivers, cyclists, walkers and users of public
transportation. MC33XX with GMS only.
MC33XX User Guide - Opens the on-device User Guide for the MC33XX.
Music - Play music stored on the microSD card and internal memory. MC33XX with AOSP only.
Notes - Use to take and save notes.
Phone - Use to dial a phone number when used with some Voice over IP (VoIP) clients (VoIP
telephony read only).
Photos – Use to sync photos with Google account. MC33XX with GMS only.
Play Movies & TV – View movies and video on your device. MC33XX with GMS only.
64
Using the MC33
Table 12 Applications (Continued)
Icon Description
Play Music – Use to listen to music. MC33XX with GMS only.
Play Store – Download music, movies, books, and Android apps and games from the Google
Play ™ Store. MC33XX with GMS only.
PTT Express – Use to launch the PTT Express client for Voice over IP (VoIP) communication.
RxLogger – Use to diagnose device and application issues. See RxLogger on page 99 for more
information.
RxLogger Utility – Use to monitor data from log files on the MC33XX while RxLogger is running.
See RxLogger Utility on page 100 for more information.
Search - Use the Google search engine to search the Internet and the MC33XX.
Settings - Use to configure the MC33XX.
SimulScan - Use to demonstrate the document capture feature of the MC33XX. See the Integrator
Guide for more information.
SMARTMU - A diagnostic intelligent app. Use to diagnose surrounding area and display network
stats, such as coverage hole detection, or AP in vicinity. See the Integrator Guide for more
information.
Sound Recorder - Use to record audio.
StageNow - Allows the MC33XX to stage a device for initial use by initiating the deployment of
settings, firmware and software.
Videos - Use to view videos on the MC33XX. MC33XX with AOSP only.
Velocity - Opens the Ivanti (formerly Wavelink) terminal emulation application.
Voice Search - Use to perform searches by asking questions. MC33XX with GMS only.
YouTube ™ - Use to view videos on the YouTube web site. MC33XX with GMS only.
65
Using the MC33
Accessing Applications
All applications installed on the device are accessed using the APPS window.
1. On the Home screen, swipe up from the bottom of the screen.
Figure 50 APPS Window Example
2. Slide the APPS window up or down to view more application icons. Touch an icon to open the application.
See Application Shortcuts and Widgets on page 54 for information on creating a shortcut on the Home screen.
Switching Between Recent Applications
1. Touch . A window appears on the screen with icons of recently used applications.
Figure 51 Recently Used Applications
2. Slide the window up and down to view all recently used applications.
3. Swipe left or right to remove application from the list and force close the application.
4. Touch an icon to open it or touch to return to the current screen.
66
Un-Locking the Screen
AOSP GMS
Use the Lock screen to protect access to data on the MC33XX. Some email accounts require locking the screen.
Refer to the MC33XX Integrator Guide for information on setting up the locking feature.
When locked, a pattern, PIN or password is required to unlock the device. Press the Power button to lock the
screen. The device also locks after a pre-defined time-out.
Press and release the Power button to wake the device. The Lock screen displays. Swipe the screen up to unlock.
If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
Figure 52 Lock Screen (AOSP & GMS)
Using the MC33
Figure 53 PIN Screen
67
Figure 54 Pattern Screen
Figure 55 Password Screen
Using the MC33
Interactive Sensor Technology
The device contains sensors that monitor movement, orientation and ambient light:
• Gyroscope - Measures angular rotational velocity to detect rotation of the device.
• Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
In order to take advantage of these sensors, applications use API commands. Refer to the Zebra Android EMDK
for more information.
Resetting the Device
There are two reset functions, soft reset and hard reset.
68
Using the MC33
Performing a Soft Reset
Perform a soft reset if applications stop responding.
1. Press and hold the Power button until the menu appears.
2. Touch Reboot.
3. The device reboots.
Performing a Hard Reset
CAUTION: Performing a hard reset with a microSD card installed in the MC33XX may cause damage or data
corruption to the micro SD card.
All un-saved data is lost after performing a hard reset.
Perform a Hard Reset if the device stops responding. To perform a Hard Reset:
1. Simultaneously press and hold the Power button, 1 and 9 keys for five seconds.
2. The device reboots.
Suspend Mode
The MC33XX goes into suspend mode when the user presses the Power button or after a period of inactivity (set in
the Display settings window).
To wake the MC33XX from Suspend mode, press the Power button. The Lock screen displays. Swipe the screen
up to unlock. If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock
screen. If the PIN or Password screen unlock feature is enabled, enter the PIN or Password after unlocking the
screen.
NOTE: If the user enters the PIN, password or pattern incorrectly five times, they must wait 30 seconds
before trying again.
If the user forgets the PIN, password or pattern contact the system administrator.
Transferring Files with a Host Computer via USB
Connect the MC33XX to a host computer using the USB Charging cable or the 1-Slot USB cradle to transfer files
between the MC33XX and the host computer. See Accessories for more information.
When connecting the MC33XX to a host computer, follow the host computer’s instructions for connecting and
disconnecting USB devices, to avoid damaging or corrupting files.
Transferring Files using Media Transfer Protocol
NOTE Use Media Transfer Protocol (MTP) to copy files between the MC33XX (internal memory or microSD
card) and the host computer.
1. Connect the Rugged Charge/USB Cable to the MC33XX or place the MC33XX into the 1-Slot USB/Charge
Only Cradle. See Accessories for setup information.
2. Pull down the Notification panel and touch USB charging this device.
69
Using the MC33
Figure 56 Use USB Dialog Box
3. Touch Transfer files.
4. On the host computer, open a file explorer application.
5. Locate the MC33XX as a portable device.
6. Open the SD card or the Internal storage folder.
7. Copy files to and from the MC33XX or delete files as required.
Transferring Files using Photo Transfer Protocol
NOTE Use Photo Transfer Protocol (PTP) to copy photos from either the microSD card or internal memory to the
host computer.
1. Connect the USB Cable to the MC33XX or place the MC33XX into the 1-Slot Ethernet Cradle. See
Accessories for setup information.
2. Pull down the Notification panel and touch USB charging this device.
Figure 57 Use USB Dialog Box
3. Touch Transfer photos (PTP).
4. On the host computer, open a file explorer application.
5. Open the SD card or the Internal storage folder.
70
Using the MC33
6. Copy or delete photos as required.
Disconnect from the Host Computer
CAUTION Carefully follow the host computer’s instructions to unmount the microSD card and disconnect USB
devices correctly to avoid losing information.
1. On the host computer, unmount the device.
2. Remove the USB cable from the device or remove the device from the cradle.
71
Using the MC33
72
Using the MC33
73
Applications
Introduction
This section describes the applications installed on the device.
Battery Manager
The Battery Manager provides detailed information about the battery.
To open Battery Manager, swipe up from the bottom of the Home screen and touch .
Figure 58 Battery Manager Screen
74
Applications
Table 13 Battery Icon Description
Battery Icon Description
Indicates battery charge level.
Indicates battery charging.
Indicates battery charge level is below 20%.
• Battery level - Indicate the current battery charge level as a percentage. Displays -% when level is unknown.
• Battery status
• Not charging - Indicates that the device is not connected to AC power.
• Charging over AC - Indicates that the device is connected to AC power and charging.
• Charging over USB - Indicates that the device is connected to a host computer with a USB cable and
charging.
• Discharging - Indicates that the battery is discharging.
• Full - Indicates that the battery is fully charged.
• Unknown - Indicates that the battery status is unknown.
• Battery health - Indicates the health of the battery. If a critical error occurs, appears. Touch to view error
description.
• Decommission - The battery is past it’s useful life and should be replaced. See system administrator.
• Good - The battery is good.
• Charge error - An error occurred while charging. See system administrator.
• Over Current - An over-current condition occurred. See system administrator.
• Dead - The battery has no charge. Replace the battery.
• Over Voltage - An over-voltage condition occurred. See system administrator.
• Below Temperature - The battery temperature is below the
• Failure Detected - A failure has been detected in the battery. See system administrator.
• Unknown - See system administrator.
• Wear level - Indicates the health of the battery in graphical form. When the wear level exceeds 80%, the bar
color changes to red.
75
Applications
• Advanced info - Touch to view additional battery information.
• Battery present status - Amount of usable charge remaining in the battery at present, under the current
discharge conditions.
• Battery level - Indicates battery charge level as a percentage of scale.
• Battery scale - Battery scale level used to determine battery level (100).
• Battery voltage - Indicates current battery voltage in millivolts.
• Battery temperature - Indicates current battery temperature in degrees Centigrade.
• Battery technology - Lists the type of battery.
• Battery Current - Lists battery current in uA.
• Battery manufacture date - Lists the date of manufacture.
• Battery serial number - Lists the battery serial number. The number matches the serial number printed
on the battery label.
• Battery part number - Lists the battery part number. The number matches the part number printed on the
battery label.
• Battery rated capacity - Lists the rated minimum capacity for the battery.
• Battery decommission status - Lists the status of the battery as Good or Decommissioned.
• Base cumulative charge - Cumulative charge using Zebra charging equipment only.
• Battery present capacity - Maximum amount of charge that could be pulled from the battery under the
present discharge conditions if the battery were fully charged.
• Battery health percentage - With a range from 0 to 100, this is the ratio of “present_capacity” to
“design_capacity” at a discharge rate of “design_capacity”.
• % decommission threshold - Lists the default % decommission threshold for a gifted battery as 80%.
• Battery present charge - Amount of usable charge remaining in the battery at present under the current
discharge conditions.
• Battery total cumulative charge - Lists the total accumulated charge in all chargers.
• Battery time since first use - Lists the time passed since the battery was placed in a Zebra terminal for
the first time.
• App version - Lists the application version number.
File Browser
Use the File Browser application to view and mange files on the device.
To open File Browser, swipe up from the bottom of the Home screen and touch .
76
Applications
Figure 59 File Browser Screen
The address bar indicates the current folder path. Touch the current folder path to manually enter a path and folder
name.
Use to select multiple files/folder.
Use to view the device root folder.
Use to view the internal storage folder.
Use to view the previous folder or to exit the application.
Touch and hold an item to perform an operation on that item. Select one of the options from the File Operations
menu:
• Information - View detailed information about the file or folder.
• Move - Move the file or folder to a new location.
• Copy - Copy the select file.
• Delete - Delete the selected file.
• Rename - Rename the select file.
• Open as - Open the selected file as a specific file type.
• Share - Share the file with other devices.
Touch to open menu options:
• New Folder - Create a new folder.
• Search - Search for a specific file on the device.
• Sort - Select the sort order of the files by name, type, size or date.
• Refresh - Refresh the current folder.
• List View - Change the folder to display item is a list.
• Grid View - Change the folder to display item is a grid.
• Change Size - Change the size of the icons.
• About File Browser - Displays the app version.
77
Contacts
Use the Contacts application to manage contacts.
From a Home or Apps screen, touch . Contacts opens to the main list of contacts. View contacts in three ways
at the top of the screen: Groups, All contacts, and Favorites. Touch the tabs to change how to view the contacts.
Swipe up or down to scroll through the lists.
Figure 60 Contacts Screen
Applications
Adding Contacts
1. In the Contacts application, touch .
2. If there are more than one account with contacts, touch the one to use.
3. Type the contact’s name and other information. Touch a field to start typing, and swipe down to view all
categories.
4. To open a menu with preset labels, such as Home or Work for an email address, touch the label to the right of
the contact information. Or to create your own label, touch Custom in the menu.
5. Touch .
Editing Contacts
1. In the Contacts application, touch a contact name to edit.
2. Touch .
3. Edit the contact information.
4. Touch .
Deleting Contacts
1. In the Contacts application, touch a contact name to delete.
2. Touch .
3. Touch Delete.
78
4. Touch Delete to confirm.
Camera Mode
Settings
Beautification
Scene Mode
Shutter Button
Gallery
Camera
This section provides information for taking photos and recording videos using the integrated digital cameras.
Taking Photos
1. Swipe up from the bottom of the Home screen and touch .
Figure 61 Camera Mode
Applications
NOTE: If a microSD card is installed and the storage path is changed manually, the MC33XX saves photos and
videos on the microSD card. By default, or if a microSD card is not installed, the MC33XX saves photos and
videos on the internal storage.
NOTE: Camera settings are described in Photo Settings on page 81.
2. If necessary, touch the Camera Mode icon and touch .
3. Frame the subject on the screen.
79
Applications
4. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on
the screen.
5. Touch an area on the screen to focus. The focus circle appears on the screen. The two bars turn green when
in focus.
6. Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
Taking a Panoramic Photo
Panorama mode lets the user create a single wide image by panning slowly across a scene.
1. Swipe up from the bottom of the Home screen and touch .
Figure 62 Panoramic Mode
2. Touch the Camera Mode and touch .
3. Frame one side of the scene to capture.
4. Touch and slowly start panning across the area to capture. A small white square appears inside the button
indicating the capture is in progress.
If panning too quickly, the message Too fast appears.
5. Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves
the image.
80
Applications
Camera Mode
Settings
Audio
Shutter Button
Gallery
Recording Videos
To record a video:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch the options bar and touch .
Figure 63 Video Mode
3. Point the camera and frame the scene.
4. To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on
the screen.
5. Touch to start recording.
The device starts recording the video. The video time remaining appears in the top left of the screen.
6. Touch to end recording.
The video momentarily displays as a thumbnail in the lower left corner.
Photo Settings
When in Photo mode, photo settings are displayed on screen. Touch to display the photo settings options.
81
Applications
• Flash - Touch to set whether the camera relies on its light meter to decide whether a flash is necessary, or
to turn it on or off for all shots.
• Off - Disable flash.
• Auto - Camera adjusts flash automatically depending upon light meter (default).
• On - Enable flash upon taking a photo.
• Torch - Turn flash on continuously.
• Picture size - Touch to set the size (in pixels) of the photo. Options: 13M pixels (default), 8M pixels, 5M
pixels, 3M pixels, HD 1080, 2M pixels, 1.3M pixels, HD 720, 1M pixels, WVGA, VGA, or QVGA.
• Picture quality - Touch to select picture quality setting. Options: Low, Standard (default) or High.
• Countdown timer - Options: Off (default), 2 seconds, 5 seconds or 10 seconds.
• Storage – Touch to select location to store the photo. Options: Phone or SD Card.
• Face Detection - Select to enable face detection. Options: Off (default) or On.
• ISO - Set how sensitive the camera is to light. Options: Auto (default), ISO Auto (HJR), ISO100, ISO200,
ISO400, ISO800 or ISO1600.
• Exposure - Touch to adjust the exposure settings. Options: +2, +1, 0(default), -1 or -2.
• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most
natural-looking colors.
• Incandescent - Adjust the white balance for incandescent lighting.
• Fluorescent - Adjust the white balance for florescent lighting.
• Auto - Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
• Focus mode - Touch to select the camera focus setting. Options: Auto, Infinity, Macro or CAF
(Continuous Auto Focus) (default).
• ZSL - Set the camera to immediately take a picture when the button is pressed (default – enabled)
Video Settings
When in Video mode, video settings are displayed on screen. Touch to display the video settings options.
• Flash - Touch to set whether Rear-facing Camera relies on its light meter to decide whether a flash is
necessary, or to turn it on or off for all shots.
• Off - Disable flash (default).
• Torch - Turn flash on continuously.
• Video quality - Touch to select video quality. Options: HD 1080p (default), HD 720p, or SD 480p.
• Video duration - Options: 30 seconds (MMS) or 30 minutes (default).
• Storage – Touch to select location to store the photo. Options: Phone (default) or SD Card.
• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most
natural-looking colors.
• Incandescent - Adjust the white balance for incandescent lighting.
82
Gallery
Use Gallery to:
Applications
• Fluorescent - Adjust the white balance for florescent lighting.
• Auto - Adjust the white balance automatically (default).
• Daylight - Adjust the white balance for daylight.
• Cloudy - Adjust the white balance for a cloudy environment.
NOTE: The device supports the following image formats: jpeg, gif, png and bmp.
The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Gallery is available on MC33XX with AOSP only.
• view photos
• play videos
• perform basic editing of photos
• set photos as wallpaper
• set photos as a contact photo
• share photos and videos.
Gallery presents all photos and videos stored on the microSD card and internal memory.
To open the Gallery application, swipe up from the bottom of the Home screen and touch or in the camera
application touch the thumbnail image at the bottom left.
By default, Gallery opens to the Timeline view.
83
Figure 64 Gallery - Timeline View
Applications
Touch > Albums to view photos sorted by albums or > Videos to view only videos.
84
Figure 65 Gallery — Albums
Applications
• Touch an album to open it and view its contents. The photos and videos in the album are displayed in
chronological order.
• Touch a photo or video in an album to view it.
• Touch > Timeline to return to the main Gallery screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in
a chronologically ordered grid. The name of the album displays at the top of the screen.
85
Figure 66 Photos Inside an Album
Applications
Swipe left or right to scroll images across the screen.
Share an Album
To share an album:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch and hold an album until it highlights.
3. Touch other albums as required.
4. Touch . The Share menu opens. Touch the application to use to share the selected albums.
5. Follow the instructions within the selected application.
Get Album Information
To get album information:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch and hold an album until it highlights.
3. Touch .
4. Touch Details.
86
Applications
Deleting an Album
To delete an album and its contents:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch and hold an album until it highlights.
3. Check other albums to delete. Ensure that other albums are selected.
4. Touch .
5. In the Delete selected item? menu, touch OK to delete the album.
Working with Photos
Use Gallery to view photos on the microSD card and edit and share photos.
Viewing and Browsing Photos
To view a photo:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch a photo.
Figure 67 Photo Example
4. Swipe left or right to view the next or previous photo in the album.
5. Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is
displayed (but not saved) in the new orientation.
87
Applications
6. Touch the photo to view the controls.
7. Double-tap the screen to zoom in or pinch two fingers together or spread them apart to zoom in or out.
8. Drag the photo to view parts that are not in view.
Cropping a Photo
To crop a photo:
1. In Gallery, touch a photo to view the controls.
2. Touch > . The cropping tool appears.
3. Use the cropping tool to select the portion of the photo to crop.
• Drag from the inside of the cropping tool to move it.
• Drag an edge of the cropping tool to resize it to any proportion.
Figure 68 Cropping Tool
4. Touch the check mark > SAVE to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
To set a photo as a contact icon:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch the photo to open it.
4. Touch .
88
Applications
5. Touch Set picture as.
6. Touch Contact photo.
7. In the People application, touch a contact.
8. Touch the white box and crop the photo accordingly.
9. Touch Save.
Share a Photo
To share a photo:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch the application to use to share the selected photo. The application selected opens with the photo
attached to a new message.
Deleting a Photo
To delete a photo:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch a photo to open it.
4. Touch .
5. Touch OK to delete the photo.
Working with Videos
Use Gallery to view videos and share videos.
Watching Videos
To watch a video:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch a video.
4. Touch . The video begins to play.
5. Touch the screen to view the playback controls.
Sharing a Video
To share a video:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch a video to open it.
89
4. Touch . The Share menu appears.
5. Touch the application to use to share the selected video. The application selected opens with the video
Deleting a Video
To delete a video:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch an album to open it.
3. Touch a video to open it.
4. Touch .
5. Touch OK.
Photos
Applications
attached to a new message.
NOTE: The device supports the following image formats: jpeg, gif, png and bmp.
The device supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Photos is available on MC33XX with GMS only.
Use Photos to:
• view photos
• play videos
• perform basic editing of photos
• set photos as wallpaper
• set photos as a contact photo
• share photos and videos.
Photos presents all photos and videos stored on the microSD card and internal memory.
To open the Photos application, swipe up from the bottom of the Home screen and touch .
By default, Photos open to the Photos view.
• Touch an album to open it and view its contents. The photos and videos in the album are displayed in
chronological order.
• Touch a photo or video in an album to view it.
• Press to return to the main screen.
Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in
a chronologically ordered grid. The name of the album displays at the top of the screen.
Swipe up to scroll images across the screen.
90
Applications
Deleting an Album
To delete an album and its contents:
1. Touch an album to open it.
2. Touch > Delete device folder.
3. In the delete folder dialog box, touch Delete.
Working with Photos
Use Photos to view photos on the internal memory and the microSD card.
Viewing and Browsing Photos
To view a photo:
1. Touch an album to open it.
2. Touch a photo.
Figure 69 Photo Example
• Swipe left or right to view the next or previous photo in the album.
• Turn the device to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is
displayed (but not saved) in the new orientation.
• Touch the photo to view the controls.
• Pinch two fingers together or spread them apart to zoom in or out.
• Drag the photo to view parts that are not in view.
Cropping a Photo
To crop a photo:
1. Touch a photo to view the controls.
2. Touch > . The cropping tool appears.
3. Use the cropping tool to select the portion of the photo to crop.
• Drag from the inside of the cropping tool to move it.
91
Applications
• Drag an edge of the cropping tool to resize it to any proportion.
Figure 70 Cropping Tool
4. Touch DONE.
5. Touch SAVE to save a copy of the cropped photo. The original version is retained.
Setting a Photo as a Contact Icon
To set a photo as a contact icon:
1. Touch the photo to open it.
2. Touch .
3. Touch Use as.
4. Touch Contact photo.
5. In the Contacts application, touch a contact.
6. Touch the white box and crop the photo accordingly.
7. Touch Done.
Share a Photo
To share a photo:
1. Touch an album to open it.
2. Touch a photo to open it.
3. Touch .
4. Touch the application to use to share the selected photo. The application selected opens with the photo
attached to a new message.
Deleting a Photo
To delete a photo:
1. Touch a photo to open it.
2. Touch .
92
Applications
3. Touch Move to Trash to delete the photo.
Working with Videos
Use Photos to view videos and share videos.
Watching Videos
To watch a video:
1. Touch an album to open it.
2. Touch a video. The video automatically starts playing.
3. Touch the screen to view the playback controls.
Sharing a Video
To share a video:
1. Touch an album to open it.
2. Touch a video to open it.
3. Touch . The Share menu appears.
4. Touch the application to use to share the selected video. The application selected opens with the video
attached to a new message.
Deleting a Video
To delete a video:
1. Touch an album to open it.
2. Touch a video to open it.
3. Touch .
4. Touch Move to trash to delete the video.
93
DataWedge Demonstration
NOTE See the MC33XX Mobile Computer Integrator Guide for information on DataWedge configuration.
Use DataWedge Demonstration to demonstrate data capture functionality.
Figure 71 DataWedge Demonstration Window
Applications
Table 14 DataWedge Demonstration Icons
Feature Icon Description
Illumination
Data Capture Indicates that the data capture function is through the internal imager.
Scan Mode Indicates imager is in picklist mode. Touch to change to normal scan
Menu Opens a menu to view the application information or to set the
Indicates imager illumination is off. Touch to turn illumination on.
Indicates imager illumination is on. Touch to turn illumination off.
Indicates that an RS6000 Bluetooth imager is not connected to the
MC33XX.
Indicates that an RS6000 Bluetooth imager is connected to the
MC33XX.
mode.
Indicates imager is in normal scan mode. Touch to change to picklist
mode.
application DataWedge profile.
Touch the Data Capture icon to select the data capture mode.
94
Applications
Figure 72 Data Capture Options Menu
Select a scanner to use. See Data Capture for configuring scanner options.
Either press the programmable button or touch the yellow scan button to enable data capture. The captured data
appears in the text field below the yellow button.
Sound Recorder
Use Sound Recorder to record audio messages.
Recordings are saved on the microSD card (if installed) or the Internal Storage and available in the Music
application playlist titled "Audio Recordings."
Figure 73 Sound Recorder Application
95
PTT Express Voice Client
Notification Icon
Service Notification
Talk Groups
Settings
Enable/Disable Switch
NOTE: PTT Express Voice Client creates Push-To-Talk (PTT) communication capability between
disparate enterprise devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT
Express delivers simple PTT communication without the need of a voice communication server.
• Group Call: Press and hold the Talk button (yellow Scan button on the MC33XX-G keypad or the right
Scan button on MC33XX-R/S) to start communicating with other voice client users.
• Private Response: Press and release and then press and hold the Talk button to respond to the originator
of the last broadcast or to make a Private Response.
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
• Talk Tone: Double chirp. Plays when the Talk button is depressed. This is a prompt for the user to start
talking.
• Access Tone: Single beep. Plays when another user just finished a broadcast or response. The user is
now able to initiate a Group Broadcast or Private Response.
• Busy Tone: Continuous tone. Plays when the Talk button is depressed and another user is already
communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60
seconds).
• Network Tone:
• Three increasing pitch beeps. Plays when PTT Express has acquired the WLAN connection and the
service is enabled.
• Three decreasing pitch beeps. Plays when PTT Express has lost the WLAN connection or the service
is disabled.
Applications
Figure 74 PTT Express Default User Interface
96
Applications
Table 15 PTT Express Default user Interface Descriptions
Item Description
Notification Icon Indicates the current state of the PTT Express client.
Service Indication Indicates the status of the PTT Express client. Options: Service Enabled, Service
Disabled or Service Unavailable.
Talk Group Lists all 32 Talk Groups available for PTT communication.
Settings Opens the PTT Express Settings screen.
Enable/Disable Switch Turns the PTT service on and off.
Notification Icons
Indicates the current state of the PTT Express Voice Client.
Table 16 PTT Express Default Notification Icons
Icon Description
Indicates that PTT Express Voice client is disabled.
Indicates that PTT Express Voice client is enabled but not connected to a WLAN.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and listening on the
Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and communicating
on the Talk Group indicated by the number next to the icon.
Indicates that PTT Express Voice client is enabled, connected to a WLAN and in a private
response.
Indicates that PTT Express Voice client is enabled and muted.
Indicates that the PTT Express Voice client is enabled but it is not able to communicate due to
a VoIP telephony call is in progress.
Enabling PTT Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the Enable/Disable Switch to the ON position. The button changes to an ON button.
97
Applications
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a
time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE: This section describes the default PTT Express client configuration. See the PTT Express V1.2
User Guide for detailed information on using the client.
In order to use a PTT Key with PTT Express, remap BUTTON_L2 key to any available physical key, such as
LEFT_TRIGGER_1, RIGHT_TRIGGER_1, SCAN, P1 or P2. By default, a PTT button is not assigned. When the
wired headset is used, Group Calls can also be initiated using the headset Talk button. For information on how to
remap a key, refer to the MC33XX Integrator Guide.
PTT communication may be established as a Group Call.
Creating a Group Call
1. Press and hold the Scan button (or the Talk button on the headset) and listen for the talk tone to play.
If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTT
Express and the WLAN are enabled.
2. Start talking after the talk tone is heard.
If the user holds the button for more than 60 seconds (default), the call is dropped allowing others to make
Group calls. The user should release the button when finished talking to allow others to make calls.
3. Release the button when finished talking.
Responding with a Private Response
The Private Response can only be initiated once a Group Call has been established. The initial Private Response
is made to the originator of the Group Call.
1. Wait until an access tone is heard.
2. Press and release and then press and hold the Talk button and listen for the talk tone to play.
3. If a busy tone is heard, release the button and wait a moment before making another attempt. Ensure that PTT
Express and the WLAN are enabled.
4. Start talking after the talk tone plays.
5. Release the button when finished talking.
Disabling PTT Express Voice Client Communication
1. Swipe up from the bottom of the Home screen and touch .
2. Slide the Enable/Disable Switch to the OFF position. The button changes to OFF.
3. Touch .
98
RxLogger
RxLogger is a comprehensive diagnostic tool that provides application and system metrics. It allows for custom
plug-ins to be created and work seamlessly with this tool. RxLogger is used to diagnose device and application
issues. Its information tracking includes the following: CPU load, memory load, memory snapshots, battery
consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat,
FTP push/pull, ANR dumps, etc. All logs and files generated are saved onto flash storage on the device (internal or
external).
Figure 75 RxLogger
Applications
Enabling Logging
To enable RxLogger:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch START. RxLogger begins collecting data.
3. Touch .
Disabling Logging
To disable RxLogger:
1. Swipe up from the bottom of the Home screen and touch .
2. Touch STOP. RxLogger stops collecting data.
3. Touch .
99
RxLogger Utility
RxLogger Utility is a data monitoring application for viewing logs in the MC33XX while RxLogger is running. The
user can access the logs and RxLogger Utility features in the App View or the Overlay View.
In the App View the user views logs in the RxLogger Utility.
Figure 76 RxLogger Utility App View
Applications
Refer to the MC33XX Mobile Computer Integrator Guide for detailed information about using RxLogger Utility.
100
Loading...