CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT
STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER DE
CLASSE 2 EN CAS D'OUVERTURE. NE PAS REGARDER
DANS LE FAISCEAU.VORSICHT- LASERLICHT KLASSE 2,
WENN ABDECKUNG GEÖFFNET. NICHT IN DEN STRAHL
BLICKEN. ⊼ᛣ˖ᠧᓔᯊঞ㘨䫕༅ᬜᯊ᳝▔ܝ䕤ᇘ࣓Ⳉ㾚ܝᴳ
COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR
DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED
JUNE 24, 2007 AND IEC 60825-1 (Ed.2.0),EN60825-1:2007 &
IEC62471:2006 (Ed. 1.0) EN62471:2008.
LASER LIGHT- DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT. LASERLICHT- NICHT
IN DEN STRAHL BLICKEN. LASER KLASSE 2.
LUMIÈRE LASER - NE PAS REGARDER DANS
LE FAISCEAU. APPAREIL À LASER DE
CLASSE 2 630-680nm, 1mW
▔ܝ䕤ᇘ࣓Ⳉ㾚ܝᴳ㉏▔ܝѻક
3
2
1
Installation
1. Power off the ET1.
2. Remove the battery.
3. If the handstrap is installed,
rotate the handstrap to access
the expansion module screws.
4. Remove two screws using a T8
®
To rx
screwdriver.
5. Remove the existing module. Do
not remove filler plate.
6. Install the new module.
Filler Plate
7. Secure the two screws using a
T8 Torx screwdriver.
8. Replace the battery.
Data Capture
MSR Swipe
Additional Information
For detailed information on setting up and using the
Scanning and Scanning/MSR module, refer to the
ET1 Enterprise Tablet User Guide and Integrator
Guide.
Regulatory Information
This guide applies to the following model numbers:
SCANMOD-ET1 and MSRSCAN-ET1.
All Zebra devices are designed to be compliant with
rules and regulations in locations they are sold and
will be labeled as required.
Local language translations are available at the
following website:
http://www.zebra.com/support.
Any changes or modifications to Zebra equipment,
not expressly approved by Zebra could void the
user’s authority to operate the equipment.
For use only with Zebra approved and UL Listed
mobile computers. Zebra approved and UL Listed
accessories and/or Zebra approved and UL Listed/
Recognized battery packs.
Declared maximum operating temperature: 50 °C.
Health and Safety
Recommendations
Ergonomic Recommendations
CAUTION In order to avoid or minimize the
potential risk of ergonomic injury
follow the recommendations below.
Consult with your local Health &
Safety Manager to ensure that you
are adhering to your company’s
safety programs to prevent
• Reduce or eliminate repetitive motion
• Maintain a neutral postures
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy
reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures
employee injury.
Laser Devices
Class 2 laser scanners use a low power, visible light
diode. As with any very bright light source, such as
the sun, the user should avoid staring directly into
the light beam. Momentary exposure to a Class 2
laser is not known to be harmful.
CAUTION: Use of controls, adjustments or
performance of procedures other than those
specified herein may result in hazardous laser light
exposure.
Labeling
Label read:
1. CAUTION - CLASS 2 LASER LIGHT WHEN
OPEN. DO NOT STARE INTO BEAM.
2. COMPLIES WITH 21CFR1040.10 & 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO
LASER NOTICE NO. 50, DATED JUNE 24, 2007
AND IEC/EN 60825-1:2007 AND/OR IEC/EN
60825-1:2014.
3. LASER LIGHT - DO NOT STARE INTO BEAM.
CLASS 2 LASER PRODUCT.
Radio Frequency Interference
Requirements-FCC
Note: This equipment has been
tested and found to comply with
the limits for a Class B digital
the FCC rules. These limits are designed to provide
reasonable protection against harmful interference
in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help.
device, pursuant to Part 15 of
Zebra reserves the right to make changes to any
(Parts) (Pb) (Hg) (Cd) (PBB) (PBDE)
(Metal Parts)
(Circuit Modules)
(Cables and Cable
Assemblies)
(Plastic and Polymeric
Parts)
(Optics and Optical
Components)
(Batteries)
OO O O O O
OO O OX
OO O O
OO O O OO
O
OX O O OX
OO O O OO
OO
ᴿᇩ⢟䍞
(Cr (VI))
This table was created to comply with China RoHS requirements.
ᵢ㺞Ṳדᦤ6-7Ⲻ㿺ᇐ㕌Ⱦ
2㺞⽰䈛ᴿᇩ⢟䍞൞䈛䜞Ԭᡶᴿൽ䍞ᶆᯏѣⲺ䠅ൽ൞*%7㿺ᇐⲺ䲆䠅
㾷≸ԛсȾ
;㺞⽰䈛ᴿᇩ⢟䍞㠩ቇ൞䈛䜞ԬⲺḆжൽ䍞ᶆᯏѣⲺ䠅䎻࠰*%7㿺ᇐ
Ⲻ䲆䠅㾷≸ȾԷѐ൞↚༺θṯᦤᇔ䱻߫ሯр㺞ѣᢉćhĈⲺᢶᵥഖ䘑
㺂䘑ж↛䈪᱄Ⱦε
product to improve reliability, function, or design.
Zebra does not assume any product liability arising
out of, or in connection with, the application or use of
any product, circuit, or application described herein.
No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent
right or patent, covering or relating to any
combination, system, apparatus, machine,
material, method, or process in which Zebra
products might be used. An implied license exists
only for equipment, circuits, and subsystems
contained in Zebra products.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of
ZIH Corp., registered in many jurisdictions worldwide.
All other trademarks are the property of their
respective owners.
©2016 Symbol Technologies LLC, a subsidiary of
72-162929-03 Rev. A — August 2016
Zebra Technologies Corporation. All
rights reserved.
Radio Frequency Interference
Requirements – Canada
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
Marking and European
Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this device is in
compliance with all applicable Directives, 2014/30/
EU, 2014/35/EU and 2011/65/EU. The full text of the
EU Declaration of Conformity is available at the
following internet address:
http://www.zebra.com/doc.
Japan (VCCI) - Voluntary Control
Council for Interference
Class B ITE
この装置は、情報処理装置等電波障害自主規制協議
会 （ＶＣＣＩ）の基準に基づくクラス B 情報技術
装置です。この装置は、家庭環境で使用することを
目的としていますが、この装置がラジオやテレビジ
ョン受信機に近接して使用されると、受信障害を引
き起こすことがあります。 取扱説明書に従って正
しい取り扱いをして下さい。
Korea Warning Statement for Class B ITE
기 종별 사 용 자 안 내 문
B급 기기
(가정용
방송통신기기
)
이 기기는 가정용 (B 급 ) 으로
전자파적합등록을
한 기기로서 주로 가정에서
사용하는 것을 목적
으로 하며, 모든 지역에서 사용할 수
있습니다 .
Waste Electrical and
Electronic Equipment (WEEE)
English: For EU Customers: All products at the end
of their life must be returned to Zebra for recycling.
For information on how to return product, please go
to: http://www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les
produits en fin de cycle de vie doivent être retournés
à Zebra pour recyclage. Pour de plus amples
informations sur le retour de produits, consultez :
http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos
los productos deberán entregarse a Zebra al final de
su ciclo de vida para que sean reciclados. Si desea
más información sobre cómo devolver un producto,
visite: http://www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на
полезния им живот всички продукти трябва да се
връщат на Zebra за рециклиране. За
информация относно връщането на продукти,
моля отидете на адрес:
http://www.zebra.com/weee.
Deutsch: Für Kunden innerhalb der EU: Alle
Produkte müssen am Ende ihrer Lebensdauer zum
Recycling an Zebra zurückgesandt werden.
Informationen zur Rücksendung von Produkten
finden Sie unter http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono
giunti al termine del rispettivo ciclo di vita devono
essere restituiti a Zebra al fine di consentirne il
riciclaggio. Per informazioni sulle modalità di
restituzione, visitare il seguente sito Web:
http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos
no fim de vida devem ser devolvidos à Zebra para
reciclagem. Para obter informações sobre como
devolver o produto, visite:
http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten
dienen aan het einde van hun levensduur naar Zebra
te worden teruggezonden voor recycling. Raadpleeg
http://www.zebra.com/weee voor meer informatie
over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty
wycofane z eksploatacji nale¿y zwróciæ do firmy
Zebra w celu ich utylizacji. Informacje na temat
zwrotu produktów znajduj¹ siê na stronie internetowej
http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je
nutné po skonèení jejich životnosti vrátit spoleènosti
Zebra k recyklaci. Informace o zpùsobu vrácení
produktu najdete na webové stránce:
http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea
lõppedes tagastada taaskasutamise eesmärgil
Zebra'ile. Lisainformatsiooni saamiseks toote
tagastamise kohta külastage palun aadressi:
http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement
terméket a Zebra vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék
visszajuttatásának módjával kapcsolatos
tudnivalókért látogasson el a
http://www.zebra.com/weee weboldalra.
Slovenski: Za kupce v EU: vsi izdelki se morajo po
poteku življenjske dobe vrniti podjetju Zebra za
reciklažo. Za informacije o vraèilu izdelka obišèite:
http://www.zebra.com/weee.
Svenska: För kunder inom EU: Alla produkter som
uppnått sin livslängd måste returneras till Zebra för
återvinning. Information om hur du returnerar
produkten finns på
http://www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki
tuotteet on palautettava kierrätettäväksi Zebrayhtiöön, kun tuotetta ei enää käytetä. Lisätietoja
tuotteen palauttamisesta on osoitteessa
http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres
til Zebra til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på:
http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα,
στο τέλος της διάρκειας ζωής τους, πρέπει να
επιστρέφονται στην Zebra για ανακύκλωση. Για
περισσότερες πληροφορίες σχετικά με την επιστροφή
ενός προϊόντος, επισκεφθείτε τη διεύθυνση
http://www.zebra.com/weee στο Διαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu
waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu
rritornati għand Zebra għar-riċiklaġġ. Għal aktar
tagħrif dwar kif għandek tirritorna l-prodott, jekk
jogħġbok żur: http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky
výrobky musia byť po uplynutí doby ich životnosti
vrátené spoločnosti Zebra na recykláciu. Bližšie
informácie o vrátení výrobkov nájdete na:
http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų
eksploatacijos laikui, turi būti grąžinti utilizuoti į
kompaniją „Zebra“. Daugiau informacijos, kaip
grąžinti gaminį, rasite: http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to
kalpošanas mūža beigām ir jānogādā atpakaļ Zebra
otrreizējai pārstrādei. Lai iegūtu informāciju par
produktu nogādāšanu Zebra, lūdzu, skatiet:
http://www.zebra.com/weee.
Warranty
For the complete Zebra hardware product warranty
statement, go to:
http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact
your facility’s Technical or Systems Support. If there
is a problem with the equipment, they will contact the
Zebra Global Support at:
http://www.zebra.com/support.
For the latest version of this guide go to:
http://www.zebra.com/support.
CMM Disclosure
SCANMOD-ET1
MSRSCAN-ET1
QUICK REFERENCE
GUIDE
Loading...