CONTENTS OF THE BOX
CHARGER - QUAD DOCK (RV4004)
Charger
This Guide
Power supply with cable and DC plug
ALSO NEEDED - NOT INCLUDED IN RV4004
External power cable - ordered separately (varies depending on region)
WALL BRACKET - QUAD DOCK
(RV4007)
Wall bracket
(wall anchors not provided)
This Guide
WALL MOUNTING
Attach the Bracket to the Wall
1
Attach the bracket to the wall, as shown below, using anchors
that are suitable for the wall type. See the location guide on
the next panel for the positioning of the anchors.
Mounting holes
Attach the Charger to the Bracket
2
Lower the keyhole slots on the base of the charger over the
tabs on the bracket. Then push the charger towards the back
of the bracket until it clicks into place.
2. Back
1. Down
LOCATION GUIDE FOR THE
MOUNTING SCREWS
WALL MOUNTING
Rear view of bracket
2.3 in
4.1 in
[103 mm]
4.1 in
[103 mm]
TABLETOP MOUNTING
Underside of charger
Back
Front
Cross-section of mounting tab
Tabletop
6.3 in
[161 mm]
9.5 in
[240 mm]
0.4 in
[10.00 mm]
0.23 in
[5.8 mm]
4.1 in
[103 mm]
[59 mm]
Ethernet socket
DC socket
0.06 in [1.6 mm]
0.12 in [3.0 mm]
0.9 in [25 mm]
1.4 in [35 mm]
2.6 in [65 mm]
TABLETOP INSTALLATION
CHARGER NOT ANCHORED TO THE TABLE
Set the charger down on its rubber feet as shown:
.
CHARGER ANCHORED TO THE TABLE
Attach 4 Anchoring Screws to the Tabletop
1
See location guide, on the previous panel, for the positions of
the screws and the size of the screwheads.
Attach Charger to Anchoring Screws
2
Lower the keyhole slots on the base of the charger over the
screwheads. Then push the charger backwards until it clicks
into place.
1. Down
2. Back
OVER >
CONNECT THE CHARGER TO
EXTERNAL POWER
Connect the Power Supply to the Charger
1
Insert the DC plug from the power supply into the socket
on the back of the charger:
Rear view of charger
Power indicator LED
DC socket
CHARGE
Insert an EP10 into the Charger
1
Slide an EP10, as shown, into each charge compartment until
a click is heard.
BATTERY CHARGE INDICATOR
The charge LED is the left LED on EP10.
EP10
™
RV4004
CHARGER QUAD DOCK
Ethernet socket
To power supply
Connect the Power Supply to an External
2
Power Source
For a Wall-Mounted Charger...
3
Place the power supply in the holder and route the cables as
shown here:
Rear view of charger on bracket
DC socket
To external
power
Power supply
DC plug
Power indicator
LED
Charge EP10 for 3 hours to 4 hours
2
Note: Full battery performance is only reached after the fi rst few
charge/discharge cycles.
3 hours to 4 hours
0 °C to 40 °C
32 °F to 104 °F
Charge LED Behaviour Description
Off No battery detected.
Solid Green Battery charging complete.
Flashing Green Charge in progress.
Flashing Yellow Battery is not charging due
to out-of-temperature conditions.
Solid Red Unable to read battery or non Psion battery.
© Copyright 2011 by Psion Inc.
Psion, Psion Teklogix, and EP10 are trademarks of Psion Inc. Other product names
mentioned in this document are trademarks or registered trademarks of other hardware,
software, or service providers and are used herein for identifi cation purposes only.
8000232
RV4007
WALL BRACKET QUAD DOCK
QUICK
START
GUIDE
April 21, 2011
PN 8000232.A
ISO 9001 Certifi ed
Quality Management System
Loading...