CS3000 Series
Quick Reference Guide
2 CS3000 Series
No part of this publication may be reproduced or used in any form, or by
any electrical or mechanical means, without permission in writing from
Zebra. This includes electronic or mechanical means, such as
photocopying, recordin g, or information storage and retrieval system s.
The material in this manual is subject to change without notice.
The software is provided strictly on an “as is” basis. All software,
including firmware, furnished to the user is on a licensed basis. Zebra
grants to the user a non-transferable and non-exclusive license to use
each software or firmware program delivered hereunder (licensed
program). Except as note d below, such license may not be assign ed,
sublicensed, or otherwise transferred by the user without prior written
consent of Zebra. No right to copy a licensed program in whole or in part
is granted, except as permitted under copyright law. The user shall not
modify, merge, or incorporate any form or portion of a licensed program
with other program material, create a derivative work from a licensed
program, or use a licensed program in a network without written
permission from Zebra. The user agrees to maintain Zebra’s copyright
notice on the licensed pr ograms delivered hereunder, and to include the
same on any authorized copie s it makes, in whole or in part. The user
agrees not to decompile, disassemble, decode, or reverse engineer any
licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to
improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in
connection with, the application or use of any product, circuit, or
application described herein.
No license is granted, either expressly or by implication, estoppel, or
otherwise under any Zebra Technologies Corporation, intellectual
property rights. An i mplied license only exists for eq uipment, circuits, and
subsystems contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH
Corp. The Symbol logo is a r egistered trademark of Symbol
Technologies, Inc., a Zebra Technologies company.
Bluetooth is a registered trademark of Bluetooth SIG. Microsoft, Windows
and ActiveSync are either registered trademarks or trademarks of
Microsoft Corporation. All other product or service names are the
property of their respective owners.
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Quick Reference Guide 3
Mini-USB Port
Scan Button
LED
Bluetooth
Button/LED
Delete Button
Protective Cover
Introduction
The CS3000 Series scanner captures and stores
bar codes for a variety of uses, and transmits bar
code data to a host via USB connection or
Bluetooth.
This document provides basic instructions for
setting up, programming, and using the CS3000
series scanners. The scanner is available in the
following configurations:
• CS3000 - USB (batch), 0.5 GB Flash
• CS3070 - USB (batch) and Bluetooth,
0.5 GB Flash
Each scanner includes a USB host cable. A
charging cradle is also available for mounting,
charging, and host connection.
4 CS3000 Series
Charging
To charge the CS3000 series scanner, connect it
to a host PC via the USB host cable or charging
cradle. No power supply is necessary. Charge
time is approximately three hours for a fully
discharged battery.
Charging via USB Host Cable
1. Insert the mini-USB connector on the host
cable in the interface port on the scanner.
2. Connect the other end of the host cable to a
USB port on the host PC.
Quick Reference Guide 5
Charging via Charging Cradle
1. Insert the cradle’s USB connector into a USB
port on the host PC.
2. Remove the protective cover from the
scanner.
3. Place the scanner in the cradle, ensuring the
mini-USB connector in the cradle inserts into
the interface port on the scanner.
6 CS3000 Series
Connecting to a Host
Batch Connection
See Charging on page 4 for instructions on
connecting the scanner to a host PC via USB.
Note To enter batch scanning mode, the
scanner cannot be paired to a
Bluetooth host (applies to CS3070
model only).
Bluetooth Connection
Pairing
For RF-enabled scanners, to pair to a
Bluetooth-enabled host:
Note If the host does not support
Bluetooth communication, a
third-party Bluetooth adapter is
required.
1. Press the scan button (+) to wake the scanner.
2. Press and hold the Bluetooth button (round
button) for five seconds. The scanner beeps
and the Bluetooth button starts blinking quickly
to indicate that the scanner is discoverable by
the host.
3. On the host PC, launch the third party
Bluetooth pairing application and place the
application into discover Bluetooth device
mode.
4. Select the CS3070 from the discovered device
list. The Bluetooth application may prompt you
to scan a passkey it generated, or for you to
create and then scan a pin.
Quick Reference Guide 7
5. Scan Numeric Bar Codes on page 8
corresponding to the passkey, then scan Enter
on page 9.
The Bluetooth button blinks slowly to indicate that
the scanner paired with the host.
Note Bluetooth pairing suspends
temporarily while charging via a
USB cable. Disconnecting the cable
re-establishes the Bluetooth pairing.
Unpairing
To unpair the scanner and host, press the
Bluetooth button. Upon unpairing, the Bluetooth
button stops blinking.
Note To enter batch scanning mode, the
scanner cannot be paired to a
Bluetooth host (applies to CS3070
model only).
8 CS3000 Series
Numeric Bar Codes
0
1
2
3
4
5
Quick Reference Guide 9
6
7
8
9
Enter
Loading...