Zanussi ZWF1415 User Manual

INSTRUCTION BOOKLET
WASHING MACHINE
ZWF 1415W
132987620
GB
Quick Installation Guide:
visit our WEB SITE to view an install video
2
Installation
This appliance is heavy. Care should be taken when moving it.
It is dangerous to alter the specifications or attempt to modify this product in any way.
All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in instructions.
Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely.
Child Safety
This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product.
Pets and children have been known to climb into washing machines. Please check your drum before use.
The glass door becomes very hot during the washing cycle. Keep children away from the vicinity of the appliance whilst it is in operation.
Keep all packaging well away from children.
Keep all detergents in a safe place out of children’s reach.
Use
Always unplug the appliance and turn off the water supply after use.
Do not overload the appliance. See relevant section in the instruction book.
Only wash fabrics which are designed to be machine washed. If in doubt, consult the care label on the clothes.
Before washing, ensure that all pockets are empty and buttons and zips are fastened. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass before washing. Underwired bras must NOT be machine washed.
Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the machine.
Garments which have been in contact with volatile petroleum products should not be machine washed. If volatile cleaning fluids are used, care should be taken to ensure that the fluid is removed from the garment before placing in the machine.
Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum.
Only use the advised quantities of fabric softener. Damage to the fabric can ensue if you over-fill. Refer to the manufacturer’s recommendations of quantities.
As some duvets and eiderdowns should be washed in large commercial machines because of their bulk, please check with the manufacturer of the item before washing in a domestic machine.
Leave the porthole door slightly ajar between washes to preserve the door seal.
Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local Service Force Centre. Always insist on genuine spare parts.
Important Safety Information
It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the appliance.
3
Contents
For the User
Important Safety Information
2
Your New Washing Machine
4
Description of the Appliance
5 Detergent dispenser drawer 5 Child safety feature 5
The Control Panel
6-7
Programme information 7
Operating sequence
8-9 Washing 5 kg of white cotton at 90°C 8 Load the laundry 8 Measure out the detergent and the fabric softener 8 Select the required programme 8 Select the spin reduction or option 8 Select the required option (s) 8 Start the programme 9 Altering a programme 9 Interrupting a programme 9 Cancelling a programme 9 Opening the door after the programme has started 9 At the end of the programme 9
Washing 2 kg of mixed fabrics at 50°C 10 Load the laundry 10 Measure out the detergent and the fabric softener 10 Select the required programme 10 Select the spin reduction or option 10 Select the required option(s) 10 Start the machine 10 At the end of the programme 11
Washing Hints
12-13
Which detergent?.... 13
And in which form? 13
Wash Care Symbols
14
Washing Programmes
15-16
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions Hints and tips Environmental information
Maintenance and Cleaning
17-18 Descaling 17 After each wash 17 Maintenance Wash 17 External cleaning 17 Cleaning the dispenser drawer 17 Cleaning the drawer recess 17 Cleaning the pump 17-18 Cleaning the water inlet filter 18 The dangers of freezing 18 Emergency emptying out 18
Something Not Working
19-20
Service and Spare Parts
20
Guarantee Conditions
21
For the Installer
Installation Instructions
22
Technical Specifications
22
Unpacking 23 Positioning 23 Water inlet 23-24 Water drainage 24-25 Levelling 25 Special conditions 25 In the interest of the environment 25 Electrical connection 26
4
Your New Washing Machine
Your new washing machine meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption.
The programme selector dial combines the function of programme and temperature selection, making it easier to set the programme.
The programme progress display shows the washing phase and the end of the programme .
The special wool programme with its new delicate wash system treats your woollens with extreme care.
The ECO VALVE allows total use of detergent and reduces water consumption so saving energy.
Ecological hints
To save water and energy and help protect the environment, we recommend that you follow these hints:
Adjust the quantity of detergent according to the hardness of your water supply, the amount of laundry and the degree of soiling.
A programme without prewash is sufficient for normally soiled laundry.
The machine works more economically if it is fully loaded.
With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature, so saving energy.
In the interest
of the environment
Materials marked with the symbol are recyclable.
Check with your local Council or Environmental Health Office to see if there are facilities in your area for re-cycling this appliance.
When the appliance is to be scrapped, cut off the power supply cable and make the door lock device unusable to prevent young children from being trapped inside.
Help to keep your country tidy - use authorised disposal sites for your old appliance.
How do we help to protect the environment? We use recycled paper!
Important
Your machine is fitted with a balance control device, which ensures the machine is stable during the spin. If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the wash load manually and select a spin programme. For more detailed information see the section headed "Something Not Working".
5
Description of the Appliance
1Detergent dispenser drawer
2 Programme guide
3 Control panel
4 Door opening handle
5 Drain pump
6 Adjustable feet
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
Child safety feature
This machine incorporates a special child safety feature to prevent small children from being trapped inside the machine. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anti-clockwise until the groove is vertical.
1
2
3
4
5
6
C0094
P1131
6
1 Detergent dispenser drawer
Programme Option buttons
Depending on the programme, different functions can be combined. These must be selected after choosing the desired programme and before depressing the Start/Pause button. When these buttons are pressed, the corresponding pilot lights come on. When they are pressed again, the pilot lights go out. If an incorrect option is selected, the corresponding pilot light flashes for about 2 seconds.
2 Option button
By depressing this button you can reduce the final and the intermediate spin speeds or select the Rinse Hold (anti-crease) option. The corresponding pilot light comes on.
: by selecting this option the speed will be
reduced as follows:
Cotton: from 1400 to 650 r.p.m. Synthetics/Mixed fabrics and wool: from 900 to
450 r.p.m. Delicates: from 700 to 450 r.p.m.
: by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing. When the programme has finished the phase light End is on and the door is blocked to indicate that the water must be emptied out.
To do this:
turn the programme selector dial to “O”
select the drain or spin programme. The machine will perform the spin at the maximal speed .You can reduce the speed by means of the same button to adapt it to the fabrics to be spun.
depress Start/Pause button.
The Control Panel
1
234 567
8
-
3 Prewash button
Select this option if you wish your laundry to be prewashed before the main wash (not available for wool programmes and Worne once). The prewash ends with a short spin in programmes for cotton and synthetics/mixed fabrics, whereas in the programme for delicate fabrics the water is only drained.
4 Super Rinse button
This option can be selected with all programmes except the wool programmes and Worne once. The machine
will perform 2 additional rinses. This option is recommended for people who are allergic to detergents, and in areas where the water is very soft.
5 Half Load button
Select this button to reduce water consumption on the rinse cycle when washing a smaller load of cottons or linens (maximum load size = 2.5 kg).
The machine will perform 2 rinses instead of 3.
6 Start Pause button
After having selected the required programme, press this button to start the machine; the corresponding pilot light stops flashing.
To interrupt a programme which is running, depress the Start/Pause button: the corresponding pilot light starts to flash.
To restart the programme from the point at which it was interrupted, press the Start/Pause button again.
7 Programme progress display
At the beginning of the programme, only the WASHING light stays on. When the programme has finished, the End pilot light comes on.
7
The End light flashes in the event of operating problems:
4 flashes: door open
2 flashes: problem with water draining
1 flash: problem with water supply
For more information see paragraph “Something not working”?
8 Programme selector dial
The selector dial is divided into following sections:
Cotton and linen
Synthetics and Mixed fabrics
Delicates
Wool
Worne once 30°
/30’
Special programmes:
(rinses), (drain) and
(spin)
O Reset programme/OFF
The selector dial can be turned either clockwise or anticlockwise. Position correspond to cold wash and position O to Reset programme/Switching OFF of the machine.
At the end of the programme the selector dial must be turned to position O, to switch the machine off.
ATTENTION!
If you turn the programme selector dial to another programme when the machine is working, the lights of the programme progress display start to flash. The machine will not perform the new selected programme.
Programme information
The wool wash cycles of this machine have been approved by Woolmark for the washing of machine washable Woolmark products provided that the garments are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M9604.
With this programme it is possible to rinse and spin garments which have been washed by hand. The machine performs 3 rinses, followed by a final short spin at the the maximal speed that you can reduce by means of the relevant button if you are washing delicate fabrics.
For emptying out the water of the last rinse in programmes with the Rinse Hold option. Turn first the programme selector dial to O, then select drain programme and depress the Start/Pause button.
Separate spin for hand washed garments and after programmes with Rinse Hold option . Before selecting this programme the selector dial must be turned to “O”. You can reduce the speed by means of the relevant button to adapt it to the fabrics to be spun.
Note: if you have reduced the maximal spin speed by means of the relevant button to 650 r.p.m., the machine performs a short spin instaed of a long spin.
This is a complete programme to be used for lightly soiled laundry or for laundry which needs freshening up.
Max load: 2. kg . Washing temperature: 30°C Number of rinses: 2 . Programme duration: 30 minutes. Short spin at 700 r.p.m max.
Worne once 30°/30’
Spin
Drain
Rinses
Wool
8
Operating Sequence
Before the first wash, we recommend that you pour 2 litres of water into the main wash compartment of the detergent drawer in order to activate the ECO valve. Then run a synthetic cycle at 60°C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the dispenser drawer and start the machine.
WASHING 5 KG OF WHITE COTTON AT 90°C
Suppose you have 5 kg of heavy soiled laundry to wash. It is white cotton and is suitable for high temperature washing.
1. Load the laundry
Open the door by carefully pulling the door handle outwards. Place the laundry in the drum, one item at a time, shaking them out as much as possible. Close the door.
2. Measure out the detergent and the fabric softener
Pull out the dispenser drawer until it stops. Measure out the amount of detergent required, pour it into the main wash compartment and, if you wish to carry out the prewash phase, pour it into the compartment marked . If required, pour fabric softener into the compartment marked (the amount used must not exceed the “MAX” mark in the drawer). Close the drawer gently.
3. Select the required programme
Turn the programme selector dial to the 90 programme. The light Start/Pause starts to flash
.
4. Select the spin reduction or option
Press the option button repeatedly, to select the desired option. The relevant light illuminates.
5. Select the required option(s)
Select “Prewash” or “Super Rinse” option if required, the corresponding light illuminates.
P0004
C0095
C0096
9
6. Start the programme
Before starting up the machine check that:
the appliance is plugged in
the water supply tap is turned on
the drain hose is correctly and securely positioned
the door and the detergent dispenser drawer are closed.
To start the selected programme, press the Start/Pause button; the corresponding light stops flashing.
The Washing light illuminates.
The machine starts operating.
7. Altering a programme
It is possible to change any option before the programme carries it out. Before you make any change, you must pause the washing machine by pressing the “Start/Pause” button.
When the programme has started, you can only reset it by turning the programme selector dial to “O” and then to the new programme position. The washing water in the tub will not emptied out. Start the new programme by depressing the “Start/Pause” button.
8. Interrupting a programme
Depress the Start/Pause button to interrupt a programme which is running, the corresponding light starts to flash. Depress the button again to restart the programme.
9. Cancelling a programme
Turn the selector dial to O to cancel a programme which is running. Now you can select a new programme.
10. Opening the door after the
programme has started
First set the machine to PAUSE by pressing the Start/Pause button and wait about 2 minutes before opening the door to give the electric locking device time to release it. If the door still does not open, this means that the machine is already heating, that the water level is above the bottom edge of the door or that the drum is turning.
If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to “O”. After about 2 minutes the door can be opened (pay attention to the water level and temperature!).
Select again the washing programme and depress the Start/Pause button to restart the machine.
1
2. At the end of the programme
The machine stops automatically.
If the Rinse Hold option has been selected, the End phase light is on, the Start/Pause light is off and the door is blocked to indicate that the water must be emptied out before opening the door. To do this first turn the programme selector dial to “O” and then to drain programme or spin programme .
The door can then now be opened.
Release of the lock is also indicated by the illumination of the End light and the extinction of the Start/Pause button light.
Turn the programme selector dial to “O” to switch the machine off. Remove the laundry from the drum and carefully check that the drum is empty. If you do not intend to carry out another wash, close the water tap. Leave the door open to prevent the formation of mildew and unpleasant smells.
Loading...
+ 19 hidden pages