Zanussi ZDT16030FA operation manual

GETTING STARTED?
EASY.
User Manual
ZDT16030FA
EN User Manual 2
Dishwasher
DE Benutzerinformation 21

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance door when it is
open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.

GENERAL SAFETY

This appliance is intended to be used in household and similar
applications such as:
farm houses; staff kitchen areas in shops, offices and other
working environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments.
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 8 (0.8) bar (MPa)
Obey the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard.
Put knives and cutlery with sharp points in the cutlery basket
with the points down or in a horizontal position.
2
Do not keep the appliance door open without supervision to
prevent to fall on it.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.

SAFETY INSTRUCTIONS

INSTALLATION

• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the temperature is less than 0 °C.
• Follow the installation instruction supplied with the appliance.
• Make sure that the appliance is installed below and adjacent to safe structures.

ELECTRICAL CONNECTION

WARNING! Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the electrical information on the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre.
• Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the mains plug.
• This appliance complies with the E.E.C. Directives.
• Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is necessary to change the
fuse in the mains plug, use fuse: 13 amp ASTA (BS 1362).

WATER CONNECTION

• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks during and after the first use of the appliance.
• The water inlet hose has a safety valve and a sheath with an inner mains cable.
WARNING! Dangerous voltage.
• If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose.
USE
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging.
3
• Do not drink and play with the water in the appliance.
• Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes.
• The appliance can release hot steam if you open the door while a programme operates.
• Do not put flammable products or items that are wet with flammable products in, near or on the appliance.

SERVICE

• Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts.
• When you contact the Authorised Service Centre, ensure that you have the following information that is available on the rating plate. Model : PNC : Serial Number :

DISPOSAL

WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children and pets to get closed in the appliance.
4

EASY START

41 2
3 5
On/off button
1
Display
2
Delay button
3

INDICATORS

XtraDry indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates.

PROGRAMMES

Programme
P1
1)
P2
P3
3)
P4 • Normal or light
Degree of soil
Type of load
• Normal soil
• Crockery and cutlery
• All
• Crockery, cutlery,
2)
pots and pans
• Heavy soil
• Crockery, cutlery, pots and pans
soil
• Delicate crockery and glassware
Programme buttons
4
Indicators
5
Programme phases Options
• Prewash
• Wash 50 °C
• Rinses
• Dry
• Prewash
• Wash from 45 °C to 70 °C
• Rinses
• Dry
• Prewash
• Wash 70 °C
• Rinses
• Dry
• Wash 45 °C
• Rinses
• Dry
• XtraDry
• XtraDry
• XtraDry
• XtraDry
5
Programme
Degree of soil
Type of load
Programme phases Options
P5
4)
1) With this programme you have the most efficient use of water and energy consumption for crockery and
cutlery with normal soil. (This is the standard programme for test institutes).
2) The appliance senses the degree of soil and the quantity of items in the baskets . It automatically ad­justs the temperature and the quantity of water, the energy consumption and the programme duration.
3) This programme has a high temperature rinsing phase for better hygiene results. During the rinsing phase, the temperature stays at 70 °C for at least 10 minutes.
4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.

CONSUMPTION VALUES

Programme
P1 10.2 0.932 225
P2 7 - 14 0.6 - 1.6 40 - 160
P3 12.5 - 14.5 1.4 - 1.8 169 - 179
P4 12 - 14 0.7 - 0.9 75 - 85
P5 10 0.9 30
• Fresh soil
• Crockery and cutlery
1)
Water
(l)
• Wash 60 °C or 65 °C
• Rinses
Energy
(kWh)
• XtraDry
Duration
(min)
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the values.

INFORMATION FOR TEST INSTITUTES

For all the necessary information for test performance, send an email to:
info.test@dishwasher-production.com
Write down the product number (PNC) that is on the rating plate.

SETTINGS

PROGRAMME SELECTION MODE AND USER MODE

When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode.
6
In user mode, the following settings can be changed:
• The level of the water softener according to the water hardness.
• The activation or the deactivation of the acoustic signal for end of programme.
• The activation or deactivation of the rinse aid empty notification.
• The level of rinse aid according to the required dosage.

How to set the programme selection mode

The appliance is in programme selection mode when the programme indicator is on and the display shows the programme duration.
When the appliance is in programme selection mode, it is possible to set a programme and to enter the user mode.
If the control panel does not show this condition, do the cancel function.

Cancel function

These settings will be saved until you change them again.
Press and hold simultaneously and until the appliance is in programme selection mode.
With this function you can cancel the running programme or the delay start.

User mode

Press and hold simultaneously and until the indicators , , and
start to flash and the display is blank.
7

THE WATER SOFTENER

The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance.
The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales.
Water hardness
The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water in your area. It is important to set the right level of the water softener to assure good washing results.
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1) Factory setting.
2) Do not use salt at this level.
Whether you use a standard detergent or multi-tabs (with or without salt), set the proper water hardness level to keep the salt
Multi-tabs containing salt are not effective enough to soften hard water.
refill indicator active.

Adjusting the water softener

Water softener level
1)
5
2)
1
While the appliance is in user mode:
1. Press .
• The indicators , and go off.
• The indicator continues to flash.
8
• The display shows the current setting: e.g. = level 5.
2. Press to change the setting. Each time you press the button, the level increases. After level 10 you
will start again from level 1.
3. Press the on/off button to confirm the setting.

THE RINSE AID DISPENSER

The rinse aid helps to dry the dishes without streaks and stains.
The rinse aid is automatically released during the hot rinse phase.
You can set the released quantity of rinse aid between level 1 (minimum quantity) and level 6

Adjusting the rinse aid level

While the appliance is in user mode:
1. Press .
• The indicators , and go off.
• The indicator continues to flash.
• The display shows the current setting: e.g. = level 4.
2. Press to change the setting.
3. Press the on/off button to confirm the setting.

THE RINSE AID EMPTY NOTIFICATION

The rinse aid helps to dry the dishes without streaks and stains.
The rinse aid is automatically released during the hot rinse phase.
When rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid. If you are using multi-tabs containing rinse aid and
(maximum quantity). Level 0 will deactivate the rinse aid dispenser and no rinse aid will be released.
Factory setting: level 4.
you are satisfied with the drying result, you can deactivate the notification for refilling rinse aid. However, we recommend that you always use rinse aid for best drying performance.
If you use standard detergent or multi-tablets without rinse aid, activate the notification to keep the rinse aid refill indicator active.

Deactivating the rinse aid dispenser

9
While the appliance is in user mode:
1. Press
• The indicators , and go off.
• The indicator continues to flash.
• The display shows the current setting: = rinse aid dispenser activated (factory setting).
2. Press to change the setting. = rinse aid dispenser deactivated.
3. Press the on/off button to confirm the setting.
.

ACOUSTIC SIGNALS

Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals.
There is also an acoustic signal that sounds when the programme is completed. By default this

Activating the acoustic signal for the end of programme

By default this acoustic signal is deactivated but it is possible to activate it. While the appliance is in user mode:
1. Press .
• The indicators , and go off.
• The indicator continues to flash.
• The display shows the current setting: – = acoustic signal off. – = acoustic signal on.
2. Press to change the setting.
3. Press the on/off button to confirm the setting.
acoustic signal is deactivated but it is possible to activate it.

OPTIONS

Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running.
10
Not all options are compatible with each other. If you have selected non compatible options, the appliance will automatically deactivate one or more of them. Only the indicators of the options still active will stay on.

XTRADRY

Activate this option when you want to boost the drying performance. With the use of this option, the
duration of some programmes, water consumption
A
and the last rinse temperature can be affected. The option XtraDry is not a permanent option and
must be selected at every cycle.

How to activate XtraDry

Press and hold simultaneously and until the indicator comes on.

BEFORE FIRST USE

If the option is not applicable to the program, the related indicator does not come on or it flashes quickly for a few seconds and then goes off. The display shows the updated program duration.
1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start a programme to remove any processing
residuals that can still be inside the appliance.

ADDING SALT

Before first use put one litre of water in the salt container. Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after
you fill the salt container, start a programme.

ADDING RINSE AID

Do not use detergent and do not load the baskets.
When you start a programme, the appliance can take up to 5 minutes to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure will be repeated periodically.
The rinse aid helps to dry dishes without streaks ans stains. It is automatically released during the hot rinse phase.
• Fill the rinse aid dispenser until the rinse aid dispenser reaches the marking "MAX".
• Remove the spilled rinse aid with an absorbent cloth to prevent too much foam.
• Fill the rinse aid dispenser when the indicator (A) becomes clear.
11

DAILY USE

30
2
1
30
30
2
1
30
1. Open the water tap.
2. Press the on/off button to activate the
appliance.
Make sure that the appliance is in programme selection mode.
• If the salt indicator is on, fill the salt
• Make sure that there is rinse aid in the rinse aid dispenser.
3. Load the baskets.
4. Add the detergent.
5. Set and start the correct programme for the
type of load and the degree of soil.
container.
• If the rinse aid indicator is on, fill the rinse aid dispenser.

ADDING DETERGENT

If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance door.

ADDING MULTI-TABLETS

• Do not fill the salt container and the rinse aid dispenser.
• Adjust the water softener to the lowest level.
• Set the rinse aid dispenser to the lowest position.

THE AUTO OFF FUNCTION

This function decreases energy consumption by deactivating automatically the appliance when it is not operating.
The function comes into operation:
• 5 minutes after the completion of the programme.
• After 5 minutes if the programme has not started.
12

STARTING A PROGRAMME

max.
1. Keep the appliance door ajar.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme
selection mode.
3. Press the programme button until the indicator of the programme you want to set comes on. The display shows the programme duration.
4. Set the applicable options.
5. Close the appliance door to start the programme.

OPTION DELAY

1. Set the programme.
2. Press until the display shows the delay time you want to set (from 1 to 24 hours).
3. Close the appliance door to start the countdown.
When the countdown is completed, the programme starts.

OPENING THE DOOR WHILE THE APPLIANCE OPERATES

If you open the door while a programme is running, the appliance stops. It may affect the energy consumption and the programme duration. When you close the door, the appliance continues from the point of interruption.
If the door is opened for more than 30 seconds during the drying phase, the running programme will end.

CANCELLING THE DELAY START WHILE THE COUNTDOWN OPERATES

When you cancel the delay start you have to set the programme and options again.
Press and hold simultaneously
and
until the appliance is in programme
selection mode.

CANCELLING THE PROGRAMME

Press and hold simultaneously and
until the appliance is in programme
selection mode. Make sure that there is detergent in the detergent
dispenser before you start a new programme.
13

END OF THE PROGRAMME

When the programme is completed and you open the door, the appliance is automatically deactivated. Close the water tap.

HINTS AND TIPS

GENERAL

The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment.
• Remove larger residues of food from the dishes into the waste bin.
• Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase.
• Always use the whole space of the baskets.
• When loading the appliance, make sure that the dishes can be completely reached and washed by the water released from the spray arm nozzles. Make sure that items do not touch or cover each other.
• You can use dishwasher detergent, rinse aid and salt separately or you can use the multi­tablets (e.g. ''3in1'', ''4in1'', ''All in 1''). Follow the instructions written on the packaging.
• Select the programme according to the type of load and degree of soil. With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil.

USING SALT, RINSE AID AND DETERGENT

• Only use salt, rinse aid and detergent for dishwasher. Other products can cause damage to the appliance.
• In areas with hard and very hard water we recommend to use plain dishwasher detergent (powder, gel, tablets containing no additional agents), rinse aid and salt separately for optimal cleaning and drying results.
• At least once a month run the appliance with the use of appliance cleaner which is particularly suitable for this purpose.
• Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on
the tableware, we recommend that you use the tablets with long programmes.
• Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging.

WHAT TO DO IF YOU WANT TO STOP USING MULTI-TABLETS

Before you start to use separately detergent, salt and rinse aid do the following procedure.
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the shortest programme with a rinsing
phase. Do not add detergent and do not load the baskets.
4. When the programme is completed, adjust the
water softener according to the water hardness in your area.
5. Adjust the released quantity of rinse aid.
6. Activate the rinse aid empty notification.

LOADING THE BASKETS

• Only use the appliance to wash items that are dishwasher-safe.
• Do not put in the appliance items made of wood, horn, aluminium, pewter and copper.
• Do not put in the appliance items that can absorb water (sponges, household cloths).
• Remove larger residues of food from the dishes into the waste bin.
• Make soft the remaining burned food on the items.
• Put hollow items (cups, glasses and pans) with the opening down.
• Make sure that glasses do not touch other glasses.
• Put cutlery and small items in the cutlery basket.
14
Loading...
+ 30 hidden pages