© 2003 - 2012 Bicom Systems
Yealink Phones User Guide
Yealink Phones User GuideI
© 2003 - 2012 Bicom Systems
Table of Contents
Part I Introduction
1
Part II Requirements
1
Part III Installation
2
................................................................................................................................... 31 Power Adapter
................................................................................................................................... 32 Power over Ethernet (PoE)
................................................................................................................................... 33 IP Address
................................................................................................................................... 34 Factory Settings
Part IV Registering Phone
4
................................................................................................................................... 41 Manual Configuration
......................................................................................................................................................... 4UAD Settings
......................................................................................................................................................... 5Creating Extension
......................................................................................................................................................... 6Registering Phone
.................................................................................................................................................. 7Hostname or IP Address
.................................................................................................................................................. 7DNS SRV
................................................................................................................................... 92 Auto Provisioning
......................................................................................................................................................... 9UAD Settings
......................................................................................................................................................... 10Creating Extension
......................................................................................................................................................... 11Registering Phone
.................................................................................................................................................. 12DHCP
.................................................................................................................................................. 12TFTP or HTTP & HTTPS
........................................................................................................................................... 13TFTP
........................................................................................................................................... 13HTTP & HTTPS
.................................................................................................................................................. 14DNS SRV
Part V Configure BLF
15
................................................................................................................................... 161 Extension Settings
................................................................................................................................... 162 Phone Settings
Part VI Shared Parking
17
................................................................................................................................... 171 Extension Settings
................................................................................................................................... 182 PBXware Settings
1Introduction
© 2003 - 2012 Bicom Systems
1
Introduction
Yealink Phones User Guide
This User Guide is written as general guide on how to set up the Yealink phone models:
SIP-T18P, SIP-T20P, SIP-T22P, SIP-T26P, SIP-T28P, SIP-T60P and SIP-T65P to work
with PBXware 3.1.
2
Requirements
1. Identify Yealink Phone Model
To start and successfully complete registration of your Yealink phone you need to
know which phone model you will setup.
From the back of each Yealink phone there are exact model information that you
should check. Although different phone models can have exactly the same
requirements and installation procedure, phone models can also have significantly
different requirements and installation procedure, so that ignorance of your own
model may result in the inability to successfully set up your phone.
2 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
2. Phone firmware
Make sure that your phone is loaded with appropriate firmware version.
model
firmware
SIP-T18P
18.0.23.2
SIP-T20P
9.60.23.6
SIP-T22P
7.60.23.5
SIP-T26P
6.61.0.50
SIP-T28P
2.61.0.50
SIP-T60P
60.0.0.82
SIP-T65P
65.0.0.70
To find out the firmware version of your Yealink phone model open a new browser
window and enter your phone IP address in order to access the phone web
administration interface login screen. Example: http://192.168.1.22.
Login to phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
3. DHCP server
Fully configured and operational DHCP server.
4. PBXware version
In order to find out the PBXware version, please login to PBXware and navigate to
Settings: About. On the top of "About" page is a code similar to this one "PBXware
Edition: Business, Release: 3.1 (041373f), Running: 1.4.24-gc-75ee203", where
"Release" denotes the exact version of your PBXware.
3
Installation
This chapter describes how to install and connect the phone to the electrical power and
data network as well as how to apply factory settings.
The following topics are covered:
- Power adapter
3Installation
© 2003 - 2012 Bicom Systems
- Power over Ethernet (PoE)
- Factory Settings
3.1 Power Adapter
1. Connect the Network and Power
Connect the DC plug on the power adapter to the DC port on the phone and
connect the other end of the power adapter into an electrical power outlet.
Connect the ethernet cable between the Internet port on the phone and the
network port on a router or switch to access LAN.
N O TE If you are using Power ov er Etherne t (PoE), you don't ne ed to connect the
AC adapter. M ake sure the Ethe rnet cable and router or switch is Powe r ove r
Ethernet (PoE) com pliant.
3.2 Power over Ethernet (PoE)
1. Connect the Network (only)
Using a regular ethernet cable, your phone can be powered from a Power over Ethernet
(PoE) compliant router or switch.
Connect the Ethernet cable between the Internet port on the phone and an
available port on the in-line power router or switch.
N O TE If you are us ing Power ov er Etherne t (PoE), you don't need to connect the
AC adapter. M ake sure the Ethe rnet cable and router or switch is Powe r ove r
Ethernet (PoE) com pliant.
3.3 IP Address
1. Find out your Yealink phone IP Address
For Yealink phone models SIP-T20P, SIP-T22P, SIP-T26P, SIP-T28P, SIP-T60P
and SIP-T65P on the phone keyboard press Menu then Enter button to see the
phone IP address on the display. For the Yealink phone model SIP-T18P pickup the
handset and dial **90#.
3.4 Factory Settings
1. Reset to factory settings
This step is not required for out-of-the-box phones, however, if the phone has been
already used then it is a must.
Open a new browser window and enter your phone IP address in order to access
the phone web administration interface login screen. Example:
http://192.168.1.22.
4 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
Login to phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
Click on Upgrade tab.
Click on Reset button in order to reset the phone to factory settings. Phone will be
reset to the factory settings and reboot.
Wait sometime prior for device to reboot.
N O TE Do not unplug or re m ove power to the phone while it is updating firm ware
and configurations.
4
Registering Phone
This chapter describes how to identify Yealink phone model, requirements that must be
met and how to register the phone using manual configuration or auto provisioning.
The following topics are covered:
- Manual Configuration
- Auto Provisioning
4.1 Manual Configuration
This chapter describes how to set UAD settings, create PBXware extension and register
the phone using Hostname or IP Address, or DNS SRV.
The following topics are covered:
- UAD Settings
- Creating Extension
- Registering Phone
4.1.1 UAD Settings
1. Login to PBXware web administration interface
Open a new browser window and enter the IP address in order to access the
PBXware web administration login screen. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
2. UAD settings
Navigate to Settings:UAD.
5Registering Phone
© 2003 - 2012 Bicom Systems
Make sure Yealink UAD is enabled. To check the UAD status click on the edit icon
corresponding to your Yealink phone.
Make sure Status is set to Active, Auto provisioning is set to No, and DHCP
is set to Yes.
Click on the Save button to save changes.
4.1.2 Creating Extension
1. Add Extension
Navigate to Extensions. Click on Add Extension.
The standard options window will be shown below.
Select Yealink phone model from the UAD select box.
Select Location: Local or Remote.
Local is for all extensions registered on the LAN and Remote is for all extensions
registered from remote networks, WAN, Internet etc.
6 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
Click on the Next step button.
2. Extension values
Enter values into the required field text boxes.
REQUIRED FIELDS
Name
Enter a name for the extension being created. Example: John Smith.
E-mail
Enter the e-mail address associated with this extension. This e-mail address will
receive all system notification messages. Example: john.smith@bicomsystems.
com.
Click on the Save button.
4.1.3 Registering Phone
This chapter describes how to register Yealink phone using Hostname or IP Address,
or DNS SRV.
The following topics are covered:
- Hostname or IP Address
- DNS SRV
7Registering Phone
© 2003 - 2012 Bicom Systems
4.1.3.1 Hostname or IP Address
1. Login to phone web administration interface
Open a new browser window and enter your phone IP address in order to access
the phone web administration interface login screen. Example: http://192.168.1.22
Login to phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
Click on Account.
Enter or set the following details into the respective fields.
REQUIRED FIELDS
Account Active
Make sure the On radio box is selected.
Register Name
PBXware extension number. Example: 1003
User Name
Usually the same number as the Phone Number.
Password
The Secret of the extension as received in the e-mail associated with this
extension. Example: _%Z4M3*Ts9y7. A password is generated automatically
for each newly created extension.
Sip Server
Enter the Hostname or IP Address of the PBXware.
- Example for Hostname: voip.bicomsystems.com
- Example for IP Address: 192.168.1.10
Click on the Confirm button.
You'll have to wait sometime prior for the device to reboot. If everything is done
as above described, you should have successfully registered your phone to
PBXware. Dial *123 to verify registration.
4.1.3.2 DNS SRV
This chapter describes how to use a DNS SRV record which specifies the location of the
PBXware.
N O TE Y our D NS Serv er needs to be configure d correctly for this to work.
Bicom Sy ste m s can provide serv ice to se t up this for y ou.
8 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
1. Login to phone web administration interface
Open a new browser window and enter your phone IP address in order to access
the phone web administration interface login screen. Example: http://192.168.1.22
Login to phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
Click on Account.
Enter or set the following details into the respective fields.
REQUIRED FIELDS
Account Active
Make sure the On radio box is selected.
Register Name
PBXware extension number. Example: 1003
User Name
Usually the same number as the Phone Number.
Password
The Secret of the extension as received in the e-mail associated with this
extension. Example: _%Z4M3*Ts9y7. A password is generated automatically
for each newly created extension.
Sip Server
In the Sip Server field enter the Hostname.
- Example for the Hostname: bicomsystems.com
Make sure you replace Hostname from this example with your PBXware
Hostname.
Make sure DNS server is configured to automatically route registration request to a
PBXware which is actually under another domain name, example:
newbicomsystems.com.
Transport
Select DNS SRV from the drop down menu.
Click on the Confirm button.
9Registering Phone
© 2003 - 2012 Bicom Systems
You'll have to wait sometime prior for the device to reboot. If everything is done
as above described, you should have successfully registered your phone to
PBXware. Dial *123 to verify registration.
4.2 Auto Provisioning
This chapter describes how to set UAD settings, create PBXware extension and register
the phone using DHCP or Static IP address.
N O TE Auto Provisioning with DHCP or Static
IP using HT T PS not supported for Y ealink phone m odel SIP-T 18P.
The following topics are covered:
- UAD Settings
- Creating Extension
- Registering Phone
4.2.1 UAD Settings
1. Login to PBXware web administration interface
Open a new browser window and enter the IP address in order to access the
PBXware web administration login screen. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
2. UAD settings
Navigate to Settings:UAD.
Make sure Yealink UAD is enabled. To check the UAD status click on the edit icon
corresponding to your Yealink phone.
Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP
is set to Yes.
10 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
Click on the Save button to save changes.
4.2.2 Creating Extension
1. Add Extension
Navigate to Extensions. Click on Add Extension.
The standard options window will be shown below.
Select Yealink phone model from the UAD select box.
Select Location: Local or Remote.
Local is for all extensions registered on the LAN and Remote is for all extensions
registered from remote networks, WAN, Internet etc.
Click on the Next step button.
2. Extension values
Enter values into the required field text boxes.
REQUIRED FIELDS
11Registering Phone
© 2003 - 2012 Bicom Systems
Name
Enter a name for the extension being created. Example: John Smith.
E-mail
Enter the e-mail address associated with this extension. This e-mail address will
receive all system notification messages. Example: john.smith@bicomsystems.
com
Auto Provisioning
Set to Yes.
MAC Address
Enter Yealink phone MAC address. Example: 0002FDFF1536. MAC address can
be found at the back of the phone.
Click on the Save button.
4.2.3 Registering Phone
This chapter describes how to register Yealink phone using DHCP, TFTP, HTTP &
HTTPS or DNS SRV.
The following topics are covered:
- DHCP
- TFTP or HTTP & HTTPS
- DNS SRV
12 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
4.2.3.1 DHCP
1. Configure DHCP
Make sure your DHCP router is configured to use option 66 to automatically
instruct phones with the URL for auto provisioning. For more information refer to
your router documentation or contact your network administrator.
2. Phone first boot or user initiated reboot
Auto provisioning process will start during phone first boot or after reboot process has
been initiated by user. DHCP server will instruct the phone where from to pickup
appropriate configuration file. If everything is done as above described, you should
have successfully registered your phone to PBXware. Dial *123 to verify
registration.
4.2.3.2 TFTP or HTTP & HTTPS
1. Login to phone web administration interface
If there is no DHCP in your network, you can still auto provision your Yealink phone.
Please refer to your Yealink phone model User Guide for instruction about setting static
IP address. After you configure your Yealink phone to use a static IP address, continue
with the following steps.
Open a new browser window and enter your phone IP address in order to access
the phone web administration interface login screen. Example:
http://192.168.1.22.
Login to the phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
Click on Upgrade tab.
Click on Advanced tab.
You can use TFTP or HTTP & HTTPS protocols in order to Auto Provision your
Yealink phone.
Choose which protocol you want to use:
- TFTP
- HTTP & HTTPS
13Registering Phone
© 2003 - 2012 Bicom Systems
4.2.3.2.1 TFTP
In the URL field enter Hostname or IP Address.
- Example for Hostname: https://voip.bicomsystems.com/
- Example for IP Address: tftp://192.168.1.10/
Make sure you replace Hostname or IP Address from this example with your
PBXware Hostname or IP address.
Check New Config
Select Power on + Repeatedly.
Click on the Confirm button.
You'll have to wait sometime prior for the device to save changes.
Click on the Auto Provision button to run auto provisioning process, then you'll be
asked to confirm action. To continue click on OK button.
Auto provisioning process will start during phone reboot process, phone will pickup
appropriate configuration file from PBXware. If everything is done as above
described, you should have successfully registered your phone to PBXware. Dial
*123 to verify registration.
4.2.3.2.2 HTTP & HTTPS
This chapter describes how to use HTTP & HTTPS protocols in order to register Yealink
phone.
N O TE Y our PB X wa re needs to be configured correctly for this to work.
Contact
your PBXware administrator.
Bicom Sy stem s can prov ide s ervice to set up this for y ou.
In the URL field enter http:// or https:// followed by Hostname or IP
Address, followed then by /tftp/
- Example for Hostname using HTTP: http://voip.bicomsystems.com/tftp/
- Example for Hostname using HTTPS: https://voip.bicomsystems.com/
tftp/
- Example for IP Address using HTTP: http://192.168.1.10/tftp/
- Example for IP Address USING HTTPS: https://192.168.1.10/tftp/
Make sure you replace Hostname or IP Address from this example with your
PBXware Hostname or IP address.
Check New Config
Select Power on + Repeatedly.
Click on the Confirm button.
You'll have to wait sometime prior for the device to save changes.
14 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
Click on the Auto Provision button to run auto provisioning process, then you'll be
asked to confirm action. To continue click on OK button.
Auto provisioning process will start during phone reboot process, phone will pickup
appropriate configuration file from PBXware. If everything is done as above
described, you should have successfully registered your phone to PBXware. Dial
*123 to verify registration.
4.2.3.3 DNS SRV
This chapter describes how to use a DNS SRV record which specifies the location of the
PBXware.
N O TE Y our D NS Serv er needs to be configure d correctly for this to work.
Bicom Sy ste m s can provide serv ice to se t up this for y ou.
1. Check if the DNS SRV is enabled in your PBXware
Contact your PBXware administrator to find out if the DNS SRV is enabled in your
PBXware, or if you have access to the PBXware you can check this yourself.
Open a new browser window and enter the IP address in order to access the
PBXware web administration login screen. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
Navigate to Settings: Servers. Click on the server corresponding edit button.
In Auto Provisioning group, make sure Use DNS SRV when possible: is set
to Yes. If it is set to No or N/A, set to Yes and click on the Save button.
N O TE Y ou m us t re-sav e a ll y our ex tensions configured for Auto Prov isioning.
2. Login to phone web administration interface
If there is no DHCP in your network, you can still auto provision your Yealink phone.
Please refer to your Yealink phone model User Guide for instruction about setting static
IP address. After you configure your Yealink phone to use a static IP address, continue
with the following steps.
15Registering Phone
© 2003 - 2012 Bicom Systems
Open a new browser window and enter your phone IP address in order to access
the phone web administration interface login screen. Example:
http://192.168.1.22
Login to phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
Click on Upgrade tab.
Click Advanced tab.
URL
In the URL field enter the Hostname.
- Example for the Hostname: bicomsystems.com
Make sure you replace Hostname from this example with your PBXware
Hostname.
Make sure DNS server is configured to automatically route registration request to a
PBXware which is actually under another domain name, example:
newbicomsystems.com.
Check New Config
Select Power on + Repeatedly.
Click on the Confirm button.
You'll have to wait sometime prior for the device to save changes.
Click on the Auto Provision button to run auto provisioning process, then you'll be
asked to confirm action. To continue click on OK button.
Auto provisioning process will start during phone reboot process, phone will pickup
appropriate configuration file from PBXware. If everything is done as above
described, you should have successfully registered your phone to PBXware. Dial
*123 to verify registration.
5
Configure BLF
This chapter describes how to configure BLF (Busy Lamp Field) for Yealink phones.
N O TE B LF (B usy Lam p F ield) supported only with Y ealink phone m ode l SIP-T 26P and
SIP-T 28P.
The following topics are covered:
16 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
- Extension Settings
- Phone Settings
5.1 Extension Settings
1. Login to PBXware web administration interface
Open a new browser window and enter the IP address in order to access the
PBXware web administration login page. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
2. Edit extension
On the Extensions page click on the edit icon corresponding to your extension.
Click on Advanced Options button.
Navigate down to the Auto Provisioning and Presence group of settings.
Make sure Auto Provisioning is set to Yes.
Make sure Presence is set to "Yes".
Click on the Save button to save changes.
Click on Enhanced services.
Click on Directory / BLF List check box and click on Save button in order to
enable this feature.
Click on Directory / BLF List Edit button.
Enter user extension number and click on the BLF check box.
Click on Save button.
5.2 Phone Settings
1. Login to phone web administration interface
Open a new browser window and enter your phone IP address in order to access
the phone web administration interface login screen. Example:
http://192.168.1.22.
17Configure BLF
© 2003 - 2012 Bicom Systems
Login to phone web administration interface with your username and password.
Please note, factory default login details are username: admin and password:
admin.
Click on Phone.
Click on DSS Keys.
Configure 1 to 10 DSS Keys from the list.
Type: Select BLF.
Value: Enter user extension. Example: 1005
Click on Confirm button to save changes.
6
Shared Parking
This chapter describes how to configure Shared Parking which is a feature that allows a
person with a Yealink phone models SIP-T26P and SIP-T28P to pick up parked calls using
BLF buttons. Once a call is parked, BLF button on the configured phone change it's color
from green to red, indicating user about parked call. User can pickup that call by pressing
BLF button indicating that a call is parked. Please note: Extension must be configured
for Auto Provisioning.
The following topics are covered:
- Extension Settings
- PBXware Settings
6.1 Extension Settings
1. Login to PBXware web administration interface
Open a new browser window and enter the IP address in order to access the
PBXware web administration login page. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
2. Edit extension.
On the Extensions page click on the edit icon corresponding to your extension.
Click on Advanced Options button.
Navigate down to the Auto Provisioning and Presence group of settings.
Make sure Auto Provisioning is set to Yes.
18 Yealink Phones User Guide
© 2003 - 2012 Bicom Systems
Make sure Presence is set to Yes.
Click on the Save button to save changes.
Click on Enhanced services.
Enable Call Pickup.
Enable Directory / BLF List.
Click on Save button at the bottom.
Click on Directory / BLF List Edit button.
Enter 1 to 10 call parking slots into the list and make sure each BLF box is
checked.
Click on Save button.
6.2 PBXware Settings
1. Login to PBXware web administration interface
Open a new browser window and enter the IP address in order to access the
PBXware web administration login screen. Example: http://192.168.1.10
Login to PBXware with your e-mail address and password.
2. PBXware settings
Navigate to Settings:Conf files.
Make sure you are looking at extensions.con configuration file.
Copy and past below code at the bottom of extensions.conf file.
[hints]
exten => 701,hint,park:701@parkedcalls
exten => 702,hint,park:702@parkedcalls
exten => 703,hint,park:703@parkedcalls
exten => 704,hint,park:704@parkedcalls
exten => 705,hint,park:705@parkedcalls
exten => 706,hint,park:706@parkedcalls
exten => 707,hint,park:707@parkedcalls
exten => 708,hint,park:708@parkedcalls
19Shared Parking
© 2003 - 2012 Bicom Systems
exten => 709,hint,park:709@parkedcalls
exten => 710,hint,park:710@parkedcalls
4. Click on the Save button to save changes.
5. Click on the Reload button top right in order to reload PBXware for changes to
take effect.
Loading...