For information on assembling the
keyboard stand, refer to the instructions
on page 10 of this manual.
EN
SPECIAL MESSAGE SECTION
This product utilizes batteries or an external power supply (adapter). DO
NOT connect this product to any power supply or adapter other than one
described in the manual, on the name plate, or specifically recommended by Yamaha.
WARNING: Do not place this product in a position where anyone could
walk on, trip over, or roll anything over power or connecting cords of any
kind. The use of an extension cord is not recommended! If you must use
an extension cord, the minimum wire size for a 25’ cord (or less) is 18
AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician.
This product should be used only with the components supplied or; a
cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is
used, please observe all safety markings and instructions that accompany the accessory product.
SPECIFICATIONS SUBJECT TO CHANGE:
The information contained in this manual is believed to be correct at the
time of printing. However, Yamaha reserves the right to change or modify
any of the specifications without notice or obligation to update existing
units.
This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that
could cause permanent hearing loss. DO NOT operate for long periods
of time at a high volume level or at a level that is uncomfortable. If you
experience any hearing loss or ringing in the ears, you should consult an
audiologist.
IMPORTANT: The louder the sound, the shorter the time period before
damage occurs.
Some Yamaha products may have benches and / or accessory mounting
fixtures that are either supplied with the product or as optional accessories. Some of these items are designed to be dealer assembled or
installed. Please make sure that benches are stable and any optional fixtures (where applicable) are well secured BEFORE using.
Benches supplied by Yamaha are designed for seating only. No other
uses are recommended.
NOTICE:
Service charges incurred due to a lack of knowledge relating to how a
function or effect works (when the unit is operating as designed) are not
covered by the manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and consult your dealer
before requesting service.
ENVIRONMENTAL ISSUES:
Yamaha strives to produce products that are both user safe and environmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keeping with
both the letter and the spirit of the law, we want you to be aware of the
following:
Battery Notice:
This product MAY contain a small non-rechargeable battery which (if
applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes necessary,
contact a qualified service representative to perform the replacement.
This product may also use “household” type batteries. Some of these
may be rechargeable. Make sure that the battery being charged is a
rechargeable type and that the charger is intended for the battery being
charged.
When installing batteries, do not mix batteries with new, or with batteries
of a different type. Batteries MUST be installed correctly. Mismatches or
incorrect installation may result in overheating and battery case rupture.
Warning:
Do not attempt to disassemble, or incinerate any battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of
household type batteries in your area for battery disposal information.
Disposal Notice:
Should this product become damaged beyond repair, or for some reason
its useful life is considered to be at an end, please observe all local,
state, and federal regulations that relate to the disposal of products that
contain lead, batteries, plastics, etc. If your dealer is unable to assist
you, please contact Yamaha directly.
NAME PLATE LOCATION:
The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate.
You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.
Model
Serial No.
Purchase Date
92-BP (bottom)
PLEASE KEEP THIS MANUAL
2DGX-630/YPG-635 Owner’s Manual
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
OBSERVERA!
Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den
ar ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL: Netspæendingen til dette apparat er IKKE afbrudt,
sålæenge netledningen siddr i en stikkontakt, som er t endt — også
selvom der or slukket på apparatets afbryder.
VAR OITUS:
laitetta verkosta.
Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko
(standby)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured makings identifying the terminals
in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of
the three pin plug.
BLUE : NEUTRAL
BROWN : LIVE
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please contact
Yamaha Corporation of America, Electronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif.
Telephone : 714-522-9011
Type of Equipment : Digital Piano
Model Name : DGX-630/YPG-635
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including
interference that may cause undesired operation.
See user manual instructions if interference to radio reception is
suspected.
* This applies only to products distributed by
YAMAHA CORPORATION OF AMERICA.
90620
(FCC DoC)
(class B)
• This applies only to products distributed by
Yamaha Music U.K. Ltd.
(2 wires)
DGX-630/YPG-635 Owner’s Manual3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/AC power adaptor
• Only use the voltage specified as correct for the instrument. The required
voltage is printed on the name plate of the instrument.
• Use the specified adaptor (PA-5D or an equivalent recommended by Yamaha)
only. Using the wrong adaptor can result in damage to the instrument or
overheating.
• Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
• Do not place the AC adaptor cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy objects
on it, or place it in a position where anyone could walk on, trip over, or roll
anything over it.
Do not open
• Do not open the instrument or attempt to disassemble the internal parts or
modify them in any way. The instrument contains no user-serviceable parts. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
CAUTION
Water warning
• Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill into
any openings. If any liquid such as water seeps into the instrument, turn off the
power immediately and unplug the power cord from the AC outlet. Then have
the instrument inspected by qualified Yamaha service personnel.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If you notice any abnormality
• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a
sudden loss of sound during use of the instrument, or if any unusual smells or
smoke should appear to be caused by it, immediately turn off the power switch,
disconnect the adaptor plug from the outlet, and have the instrument inspected
by qualified Yamaha service personnel.
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
Power supply/AC power adaptor
• When removing the electric plug from the instrument or an outlet, always hold
the plug itself and not the cord.
• Unplug the AC power adaptor when not using the instrument, or during
electrical storms.
• Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
Location
• Do not expose the instrument to excessive dust or vibrations, or extreme cold or
heat (such as in direct sunlight, near a heater, or in a car during the day) to
prevent the possibility of panel disfiguration or damage to the internal
components.
• Do not use the instrument in the vicinity of a TV, radio, stereo equipment,
mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio
may generate noise.
(3)-11 1/2
• Do not place the instrument in an unstable position where it might accidentally
fall over.
• Before moving the instrument, remove all connected adaptor and other cables.
• When setting up the product, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
• Use only the stand specified for the instrument. When attaching the stand or
rack, use the provided screws only. Failure to do so could cause damage to the
internal components or result in the instrument falling over.
4DGX-630/YPG-635 Owner’s Manual
Connections
• Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all
components, set all volume levels to minimum. Also, be sure to set the volumes
of all components at their minimum levels and gradually raise the volume
controls while playing the instrument to set the desired listening level.
Maintenance
• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical-impregnated wiping cloths.
Handling caution
• Do not insert a finger or hand in any gaps on the instrument.
• Never insert or drop paper, metallic, or other objects into the gaps on the panel
or keyboard. If this happens, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the instrument inspected by qualified
Yamaha service personnel.
• Do not place vinyl, plastic or rubber objects on the instrument, since this might
discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
• Do not use the instrument/device or headphones for a long period of time at a
high or uncomfortable volume level, since this can cause permanent hearing
loss. If you experience any hearing loss or ringing in the ears, consult a
physician.
Saving data
Saving and backing up your data
• The panel settings and some other types of data are not retained in memory
when you turn off the power to the instrument. Save data you want to keep to the
Registration Memory (page 90.)
Saved data may be lost due to malfunction or incorrect operation. Save
important data to a USB storage device/or other external device such as a
computer (pages 99, 100, 110).
Backing up the USB storage device/external media
•To protect against data loss through media damage, we recommend that you
save your important data onto two USB storage devices/external media.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
Even when the power switch is in the “STANDBY” position, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long
time, make sure you unplug the AC power adaptor from the wall AC outlet.
The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your
instrument.
● Trademarks
• The bitmap fonts used in this instrument have been provided by and are the property of Ricoh Co., Ltd.
•Windows is a registered trademark of Microsoft
®
Corporation in the United States and other countries.
• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
(3)-11 2/2
DGX-630/YPG-635 Owner’s Manual5
Copyright Notice
The followings are the titles, credits and copyright notices for three (3) of the songs pre-installed in this
electronic keyboard:
Composition Title : Against All Odds
Composer’s Name : Collins 0007403
Copyright Owner’s Name : EMI MUSIC PUBLISHING LTD
AND HIT & RUN MUSIC LTD
All Rights Reserved, Unauthorized copying, public performance and broadcasting are strictly prohibited.
This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it
has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI
files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use
is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE
ILLEGAL COPIES.
Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited
except for your personal use.
Music Publishing Company, Inc.
International Copyright Secured All Rights Reserved
Panel Logos
GM System Level 1
“GM System Level 1” is an addition to the MIDI standard which ensures that any GM-compatible music
data can be accurately played by any GM-compatible tone generator, regardless of manufacturer. The GM
mark is affixed to all software and hardware products that support GM System Level.
XGlite
As its name implies, “XGlite” is a simplified version of Yamaha’s high-quality XG tone generation format.
Naturally, you can play back any XG song data using an XGlite tone generator. However, keep in mind that
some songs may play back differently compared to the original data, due to the reduced set of control
parameters and effects.
XF
The Yamaha XF format enhances the SMF (Standard MIDI File) standard with greater functionality and
open-ended expandability for the future. The instrument is capable of displaying lyrics when an XF file containing lyric data is played.
STYLE FILE
The Style File Format is Yamaha’s original style file format which uses a unique conversion system to provide high-quality automatic accompaniment based on a wide range of chord types.
USB
USB is an abbreviation for Universal Serial Bus. It is a serial interface for connecting a computer with
peripheral Devices. It allows “hot swapping” (connecting peripheral devices while the power to the computer is on).
6DGX-630/YPG-635 Owner’s Manual
Congratulations and thank you for purchasing
the Yamaha DGX-630/YPG-635 Portable Grand!
Please read this owner’s manual carefully before using the instrument
in order to take full advantage of its various features.
Make sure to keep this manual in a safe and handy place even after you finish reading,
and refer to it often when you need to better understand an operation or function.
Included Accessories
The DGX-630/YPG-635 package includes the following items. Please check that you have them all.
• Music rest
• Accessory CD-ROM
• Owner’s manual (this book)
•Keyboard stand
•Footswitch
•AC Power Adaptor (PA-5D or an equivalent recommended by Yamaha)
*May not be included depending on your particular area. Please check with your Yamaha dealer.
DGX-630/YPG-635 Owner’s Manual7
Special Features of the DGX-630/YPG-635
Graded Hammer Standard Keyboard
Thanks to our experience as the world’s leading manufacturer of acoustic pianos, we’ve developed a
keyboard with action that’s virtually indistinguishable from the real thing. Just as on a traditional acoustic piano, the keys of the lower notes have a heavier touch, while the higher ones are more responsive
to lighter playing. The keyboard’s sensitivity can even be adjusted to match your playing style. This
Graded Hammer technology also enables the DGX-630/YPG-635 to provide authentic touch in a lightweight instrument.
■ Performance assistant technology Page 39
Play along with a song on the instrument’s keyboard and produce a perfect
performance every time ... even if you play wrong notes! All you have to do
is play on the keyboard—alternately on the left- and right-hand ranges of the
keyboard, for example—and you’ll sound like a pro as long as you play in
time with the music.
And if you can’t play with both hands, you can still play the melody simply
by tapping one key.
■ Play a Variety of Instrument Voices Page 19
With the DGX-630/YPG-635, the instrument voice that sounds when you
play the keyboard can be changed to violin, flute, harp, or any of an extensive
range of voices. You can change the mood of a song written for piano, for
example, by using violin to play it instead. Experience a whole new world of
musical variety.
■ Play Along with Styles Page 28
Want to play with full accompaniment? Try the auto-accompaniment Styles.
The accompaniment styles provide the equivalent of a full backing band covering wide variety of styles from waltzes to 8-beat to euro-trance … and
much more. Select a style that matches the music you want to play, or experiment with new styles to expand your musical horizons.
All you need is
one finger!
■ Easy Performance with Music Notation Display Page 37
When you play back a song, the corresponding score will be shown on the
display as the song plays. This is a great way to learn how to read music. If
the song contains lyric and chord data*, the lyrics and chords will also appear
on the score display.
* No lyrics or chords will appear on the display if the song you are using with the score display func-
tion does not contain the appropriate lyric and chord data.
Read these cautions carefully before you assemble or use the keyboard stand.
These cautions are to promote safe use of the stand and to prevent injury and damage from occurring to you and oth-
ers. By following these cautions carefully, your keyboard stand will provide you with safe and prolonged use.
• Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the
sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage.
• Use the stand after assembly is complete. An uncompleted stand may overturn or the keyboard may drop.
•Always place the stand on a flat, stable surface. Placing the stand on uneven surfaces may cause it to become unstable or overturn,
the keyboard to drop, or injury.
• Do not use the stand for anything other than its designed purpose. Placing other objects on the stand may result in the object dropping or the stand overturning.
• Do not apply excessive force to the keyboard as it may cause the stand to overturn or the keyboard to drop.
• Make sure the stand is sturdy and safe, and all screws have been tight and firm before use. If not, the stand may overturn, the keyboard may drop, or may result in injury to the user.
•To disassemble, reverse the assembly sequence given below.
Have a phillips-head (+) screwdriver of the appropriate size ready.
z The parts shown in the “Assembly Parts” illustration will be used. Follow the assembly
instructions and select the parts as needed.
1
Assembly Parts
Back board
Side
boards
Stand
bases
q Joint connectors (4 pcs.)
w 6 x 70 mm roundhead
screws (4 pcs.)
e 6 x 30 mm roundhead
screws (4 pcs.)
r Support rail
t 4 x 45 mm flathead screws
(6 pcs.)
y 5 x 16 mm roundhead
screws (4 pcs.)
Use the packing sheet to protect both the instrument and
the floor when assembling.
* The sheet is the bag in which the instrument is wrapped.
10 DGX-630/YPG-635 Owner’s Manual
2
• If you put the connectors in wrong direction and want to take them out,
tap around the holes on the boards.
NOTE
• If you have purchased an optional pedal unit, attach the pedal unit
before proceeding to the next step. Refer to the instructions provided
with your pedal unit.
NOTE
• If you don’t have the packing sheet, use a thick blanket or other soft
material to protect the floor and the instrument.
NOTE
w 6 x 70 mm
roundhead screws
q Joint connectors
Setting Up
x Attach the stand bases.
Insert the joint connectors q into the stand boards as
shown. The joint connectors have been installed properly if
you can see the screw head on the connector.
Attach the stand bases to the bottom of the side boards,
using the screws w. The left and right stand bases are the
same shape, and there is no difference between their frontto-back orientation. If you have trouble fastening the
screws, use a screwdriver to rotate the joint connectors so
that the connector holes are aligned with the screw holes
on the stand bases.
3
4
t 4 x 45 mm
flathead
screws
e 6 x 30 mm roundhead screw
r Support rail
c Attach the back board.
Attach the back board, using the screws e. Check the
back-to-front orientation for the side boards. Make sure the
non-colored surface is facing down.
CAUTION
• Be careful not to drop the back board or touch the sharp metal fittings.
v Attach the support rail.
Spread the packing sheet on the floor. Place the instru-
ment on the sheet with the rear panel side on the bottom.
Align the support rail r into the groove on the bottom
of the instrument and attach the rail, using the screws t.
DGX-630/YPG-635 Owner’s Manual 11
Setting Up
5–6
b Put the keyboard on the stand.
Check the back-to-front orientation for stand, and carefully place the keyboard on the side boards. Slowly move
the keyboard so that the holes on the bottom of the keyboard are properly aligned with the holes on the angle
brackets.
CAUTION
• Be careful not to drop the keyboard or to get your fingers caught
between the keyboard and the stand parts.
n Install the keyboard to the stand.
Fix the keyboard to the angle brackets, using the screws
y.
y 5 x 16 mm
roundhead
screws
■ Post-assembly checklist
Once you’ve assembled the stand, check the following points:
• Are there any parts left over?
➔ If so, read the assembly instructions again and correct
any errors you might have made.
• Is the instrument clear of doors and other movable
fixtures?
➔ If not, move the instrument to an appropriate location.
• Does the instrument make a rattling noise when you
play it or move it?
➔ If so, properly tighten all screws.
• Also, if the keyboard makes a creaking noise or
seems unsteady when you play it, refer carefully to
the assembly instructions and diagrams and
retighten all screws.
12 DGX-630/YPG-635 Owner’s Manual
Be sure to do the following operations BEFORE turning on the power.
• Unplug the AC Power Adaptor when not using the instrument,
or during electrical storms.
AC power
adaptor
AC outlet
•Avoid listening with the headphones at high volume for long periods of time; doing so may not only result in ear fatigue, it may be
damaging to your hearing.
•To prevent damage to the speakers, set the volume of the external
devices at the minimum setting before connecting them. Failure to
observe these cautions may result in electric shock or equipment
damage. Also, be sure to set the volumes of all devices at their
minimum levels and gradually raise the volume controls while
playing the instrument to set the desired listening level.
• Make sure that the footswitch plug is properly connected to the SUSTAIN jack before turning on the power.
• Do not press the footswitch while turning the power on. Doing this
changes the recognized polarity of the footswitch, resulting in reversed
footswitch operation.
NOTE
Power Requirements
Setting Up
Make sure that the [STANDBY/ON] switch of the
instrument is set to STANDBY.
WARNING
• Use the specified adaptor (PA-5D or an equivalent recommended by Yamaha) only. The use of other adaptors may
result in irreparable damage to both the adaptor and the
instrument.
Plug the AC adaptor into an AC outlet.
CAUTION
Connect the AC adaptor to the power supply jack.
Make all necessary connections below BEFORE turning the power on.
Connecting Headphones (PHONES/OUTPUT Jack)
The instrument speakers are automatically shut off
when a plug is inserted into this jack. The PHONES/
OUTPUT jack also functions as an external output. You
can connect the PHONES/OUTPUT jack to a keyboard
amplifier, stereo system, mixer, tape recorder, or other
line-level audio device to send the instrument’s output
signal to that device.
Connecting a Footswitch (SUSTAIN Jack)
WARNING
CAUTION
The sustain function lets you produce a natural sustain
as you play by pressing a footswitch. Plug the Yamaha
FC5 footswitch into this jack and use it to switch sustain
on and off.
DGX-630/YPG-635 Owner’s Manual 13
Setting Up
Connecting a Pedal Unit (PEDAL UNIT jack)
This jack is for connecting an optional LP-7 pedal
unit. When connecting the pedal unit, make sure to
also assemble the unit on the supplied keyboard
stand.
NOTE
• Make sure that power is OFF when connecting or disconnecting
the pedal.
Keyboard
LP-7
(optional)
Pedal Unit Functions
The optional pedal unit has three foot pedals that produce a range of
expressive effects similar to those produced by the pedals on an acoustic
piano. The pedal unit does not affect the split voice when the keyboard is
in split mode.
Stand
Damper (Right) Pedal
The damper pedal functions in the same way as a damper pedal on an
acoustic piano. When the damper pedal is pressed, notes sustain
longer. Releasing the pedal immediately stops (damps) any sustained
notes.
A “half-pedal” effect lets you use the damper pedal to create partial
sustain effects, depending on how far down you press the pedal.
* When using both the foot switch and pedal unit, the last effect applied takes
priority.
Sostenuto (Center) Pedal
If you play a note or chord on the keyboard and press the sostenuto
pedal while the note(s) are held, those notes will sustain as long as you
hold the pedal (as if the damper pedal had been pressed) but all subsequently played notes will not be sustained. This makes it possible to
sustain a chord, for example, while other notes are played “staccato.”
Soft (Left) Pedal
The soft pedal reduces the volume and slightly changes the timbre of
notes played while the pedal is pressed. The soft pedal will not affect
notes that are already playing when it is pressed.
When you press the damper
pedal here, the notes you play
before you release the pedal
have a longer sustain.
When you press the sostenuto
pedal here while holding the
note, the note will sustain as
long as you hold the pedal.
14 DGX-630/YPG-635 Owner’s Manual
Connecting to a Computer (USB Terminal)
• Even when the switch is in the “STANDBY” position, electricity is
still flowing to the instrument at the minimum level. When you are
not using the instrument for a long time, make sure you unplug the
AC power adaptor from the wall AC outlet.
•Never attempt to turn the power off when a “WRITING!” message
is shown in the display. Doing so can damage the flash memory
and result in a loss of data.
Connect the instrument’s USB terminal to the USB terminal of a computer, and you can transfer performance
data and song files between the two (page 105). To use
the USB data-transfer features you’ll need to do the following:
• First, make sure the POWER switch on the instrument is set to OFF, then use an AB type USB cable
to connect the instrument to the computer. After
making the connections, turn the instrument’s
power on.
• Install the USB-MIDI driver on your computer.
Installation of the USB-MIDI driver is described on
page 113.
Turning the Power On
Setting Up
Turn down the volume by turning the [MASTER VOLUME] control to the left and press the [STANDBY/ON]
switch to turn on the power. Press the [STANDBY/ON]
switch again to turn the power OFF.
● Music Rest
Backup data in the flash memory is loaded to the instrument when the power is turned on. If no backup data
exists on flash memory, all instrument settings are
restored to the initial factory defaults when the power is
turned on.
#9 PEDAL UNIT jack.................................... page 14
$0 PHONES/OUTPUT jack .......................... page 13
$1 DC IN 12V jack ........................................ page 13
DGX-630/YPG-635 Owner’s Manual 17
G
k
u
c
i
u
Q
i
d
e
Changing the Display Language
Quick Guide
This instrument allows you to select English or Japanese as the display
language. The default display language is English, but if you switch to
Japanese the lyrics, file names, demo display, and some messages will be
displayed in Japanese where appropriate.
Press the [FUNCTION] button.
1
Press the CATEGORY [] and [] buttons a number of
times until the “Language” item appears.
2
The currently selected display language will appear below the “Language” item.
When highlighted you can use the [+] and [-] buttons to select the language as required.
Select a display language.
3
The [+] button selects English and the [-] button selects Japanese.
The language selection will be stored in the internal flash memory so
that it is retained even when the power is turned off.
f
Language item
The currently selected
language
Press the [EXIT] button to return to the MAIN display.
4
18 DGX-630/YPG-635 Owner’s Manual
G
k
u
c
i
u
Q
i
d
e
Try Playing a Variety of Instrument Voices
In addition to piano, organ, and other “standard” keyboard instruments,
this instrument has a large range of voices that includes guitar, bass,
strings, sax, trumpet, drums and percussion, sound effects … a wide variety of musical sounds.
Select and Play a Voice—MAIN
This procedure selects the main voice you will play on the keyboard.
Press the [VOICE] button.
1
The main voice selection display will appear.
The currently selected voice number and name will be highlighted.
The currently
selected voice number and name
Select the voice you want to play.
2
While watching the highlighted voice name rotate the dial. The available voices will be selected and displayed in sequence. The voice
selected here becomes the main voice.
For this example select the “105 Flute” voice.
Play the keyboard.
3
Select 105 Flute
Try selecting and playing a variety of voices.
Press the [EXIT] button to return to the MAIN display.
Adjusts volume.
DGX-630/YPG-635 Owner’s Manual 19
Try Playing a Variety of Instrument Voices
Play Two Voices Simultaneously—DUAL
You can select a second voice which will play in addition to the main voice when you play the keyboard.
The second voice is known as the “dual” voice.
Press the [DUAL ON/OFF] button.
1
The [DUAL ON/OFF] button turns the dual voice on or off.
When turned on the dual voice “DUAL” will appear in the MAIN display. The currently selected dual voice will sound in addition to the
main voice when you play the keyboard.
Press and hold the [DUAL ON/OFF] button for longer than
a second.
2
The dual voice selection display will appear.
Hold for longer than a second
Select the desired dual voice.
3
Watch the displayed dual voice and rotate the dial until the voice you
want to use is selected. The voice selected here becomes the dual voice.
For this example try selecting the “123 Vibraphone” voice.
Voice Number
Dual voice selection display
The currently selected dual voice
20 DGX-630/YPG-635 Owner’s Manual
Try Playing a Variety of Instrument Voices
Play the keyboard.
4
Tw o voices will sound at the same time.
Try selecting and playing a range of dual voices.
Press the [EXIT] button to return to the MAIN display.
Play Different Voices with the Left and Right Hands—SPLIT
In the split mode you can play different voices to the left and right of the keyboard “split point”. The main
and dual voices can be played to the right of the split point, while the voice played to the left of the split
point is known as the “split voice”. The split point setting can be changed as required (page 82).
Split point
Main voice and dual voiceSplit voice
Press the [SPLIT ON/OFF] button.
1
The [SPLIT ON/OFF] button turns the split voice on or off. When
turned on the split voice “SPLIT” will appear in the MAIN display. The
currently selected split voice will sound to the left of the keyboard split
point.
Press and hold the [SPLIT ON/OFF] button for longer than
a second.
2
The split voice selection display will appear.
Voice Number
Hold for longer than a second
Split voice selection display
The currently selected split
voice
DGX-630/YPG-635 Owner’s Manual 21
Try Playing a Variety of Instrument Voices
Select the desired split voice.
3
Watch the highlighted split voice and rotate the dial until the voice you
want to use is selected. The voice selected here becomes the split voice
which will play to the left of the keyboard split point. For this example
try selecting the “041 Folk Guitar” voice.
Play the keyboard.
4
Try selecting and playing a range of split voices.
Press the [EXIT] button to return to the MAIN display.
Play the Grand Piano Voice
When you just want to play piano, all you have to do is press one convenient button.
Press the [PORTABLE GRAND] button.
The “001 Grand Piano” voice will be selected.
NOTE
• When you press the [PORTABLE GRAND] button all settings
other than touch sensitivity are
turned off. The dual and split
voices will also be turned off, so
only the Grand Piano voice will
play over the entire keyboard.
22 DGX-630/YPG-635 Owner’s Manual
Fun Sounds
This instrument includes a range of drum kits and unique sound effects you can
use for entertainment. Laughter, babbling brooks, jet fly-bys, eerie effects, and
much more. These sounds can be a great way to enhance the mood at parties.
Drum Kits
Drum kits are collections of drum and percussion instruments. When you select a violin or other
normal instrument main voice, for example, all keys produce the sound of the same violin, only at
different pitches. If you select a drum kit as the main voice, however, each key produces the sound
of a different drum or percussion instrument.
◆ Drum Kit Selection Procedure ➔ (refer to steps 1 and 2 on page 19)
1 Press the [VOICE] button.
2 Use the dial to select “131 Standard Kit 1”.
3 Try out each key and enjoy the drum and percussion sounds!
Try out each key and enjoy the drum and percussion sounds! Don’t forget the black keys! You’ll
hear a triangle, maracas, bongos, drums ... a
comprehensive variety of drum and percussion
sounds. For details on the instruments included
in the drum kit voices (voice numbers 131 to
142), see the “Drum Kit List” on page 132.
Sound Effects
The sound effects are included in the drum kit voice group (voice numbers 141 and 142). When
either of these voices are selected you will be able to play a range of sound effects on the keyboard.
◆ Sound Effect Selection Procedure ➔ (refer to steps 1 and 2 on page 19)
1 Press the [VOICE] button.
2 Use the dial to select “142 SFX Kit 2”.
3 Try out each key and enjoy the sound effects!
As you try out the various keys you’ll hear the sound of a
submarine, a telephone bell, a creaking door, and many
other useful effects. “141 SFX Kit 1” includes lightning,
running water, dogs barking, and others. Some keys do
not have assigned sound effects, and will therefore produce no sound.
For details on the instruments included in the SFX kit
voices, see “SFX Kit 1” and “SFX Kit 2” in the “Drum
Kit List” on page 133.
DGX-630/YPG-635 Owner’s Manual 23
G
k
u
c
i
u
Q
i
d
e
The Metronome
The instrument includes a metronome with adjustable tempo
and time signature. Play and set the tempo that is most comfortable for you.
Start the Metronome
Turn the metronome on and start it by pressing the [METRONOME ON/OFF] button.
To stop the metronome, press the [METRONOME ON/OFF] button
again.
Adjusting the Metronome Tempo
Press the [TEMPO/TAP] button to call up the tempo setting.
1
4/4
Current setting
Tempo
Use the dial to select a tempo from 5 to 280.
2
24 DGX-630/YPG-635 Owner’s Manual
The Metronome
Setting the Number of Beats per Measure, and the Length of Each Beat
In this example we’ll set up a 5/8 time signature.
Press and hold the [METRONOME ON/OFF] button for
longer than a second to select the function “Time Signa-
1
ture–Numerator”.
Numerator
(Number of
Hold for longer
than a second
Use the dial to select the number of beats per measure.
2
The available range is from 1 through 60. Select 5 for this example.
A bell accent will be sounded at the first beat of each measure.
Press the CATEGORY [] and [] buttons as many times
as necessary to select the beat length function “Time Sig-
3
nature–Denominator”.
beats per
measure.)
f
Denominator
(The length of
one beat.)
NOTE
• The metronome time signature
will synchronize to a style or
song that is playing, so these
parameters cannot be changed
while a style or song is playing.
Use the dial to select the beat length.
4
Select the required length for each beat: 2, 4, 8, or 16 (half note, quarter
note, eighth note, or 16
th
note). Select 8 for this example.
DGX-630/YPG-635 Owner’s Manual 25
The Metronome
Setting the Click bell sound
This allows you to select whether the click sound has a bell accent, or plays only a click sound.
Press the [FUNCTION] button.
1
Use the CATEGORY [] and [] buttons to select the Bell
item.
2
You can then use the [+] and [-] buttons to turn the bell
sound on or off.
3
Adjusting the Metronome Volume
Press the [FUNCTION] button.
f
1
Use the CATEGORY [] and [] buttons to select the Metronome Volume item.
2
Use the dial to set the metronome volume as required.
f
3
26 DGX-630/YPG-635 Owner’s Manual
Metronome volume
G
k
u
c
i
u
Q
i
d
e
Playing Styles
This instrument has an auto accompaniment feature that produces
accompaniment (rhythm + bass + chords) in the style you choose to
match chords you play with your left hand. You can select from 160 different styles covering a range of musical genres and time signatures
(see page 134 for a complete list of the available styles).
In this section we’ll learn how to use the auto accompaniment features.
Select a Style Rhythm
Most styles includes a rhythm part. You can select from a wide variety of rhythmic types—rock, blues, Euro
trance, and many, many more. Let’s begin by listening to just the basic rhythm. The rhythm part is played
using percussion instruments only.
Press the [STYLE] button.
1
The style select display will appear. The currently selected style number
and name will be highlighted.
Select a style.
2
Use the dial to select the style you want to use.
A list of all the available styles is provided on page 134.
The currently selected style
NOTE
• Style files transferred from a
computer or stored on a USB
flash memory device connected
to the instrument can be
selected and used in the same
way as the internal Styles (Style
numbers 161–). File transfer
instructions are provided on
page 108.
Press the [START/STOP] button.
3
The style rhythm will start playing.
Press the [START/STOP] button a second time when you want to stop
playback.
NOTE
• Style numbers 131, 143–160
have no rhythm part and therefore no rhythm will play if you
use them for the above example. For these styles first turn
auto accompaniment on as
described on page 28, press the
[START/STOP] button, and the
accompaniment bass and chord
parts will begin playing when
you play a key to the left of the
keyboard split point.
DGX-630/YPG-635 Owner’s Manual 27
Playing Styles
Play Along with a Style
You learned how to select a style rhythm on the preceding page.
Here we’ll see how to add bass and chord accompaniment to the basic rhythm to produce a full, rich accompaniment that you can play along with.
Press the [STYLE] button and select the desired style.
1
Turn automatic accompaniment on.
2
Press the [ACMP ON/OFF] button.
Pressing this button a second time will turn automatic accompaniment
off.
● When automatic accompaniment is on ...
The area of the keyboard to the left of the split point (54: F#2) becomes the
“auto accompaniment region” and is used only for specifying the
accompaniment chords.
Split point (54: F#2)
Auto accompaniment region
Turn sync start on.
3
Press the [SYNC START] button to turn the sync start function on.
This icon appears when
automatic accompaniment is on.
NOTE
• The keyboard split point can be
changed as required: refer to
page 82.
28 DGX-630/YPG-635 Owner’s Manual
Flashes when sync start
is on.
When sync start is on, the bass and chord accompaniment included in a
style will start playing as soon as you play a note to left of the keyboard
split point. Press the button a second time to turn the sync start function
off.
Play a left-hand chord to start the style.
4
You can still “play” chords even if you don’t actually know any chords.
This instrument will recognize even a single note as a chord. Try playing from one to three notes at the same time to the left of the split point.
The accompaniment will change according to the left-hand notes you
play.
Try this!
Scores for some chord progressions are provided on page 30. These
examples should help you get a feel for what types of chord progressions sound good with the styles.
Playing Styles
Split point
Auto accompaniment region
Play a variety of left-hand chords while playing a melody
with your right hand.
5
Split point
Auto accompaniment region
Press the [START/STOP] button to stop style playback
when you’re done.
6
You can switch style “sections” to add variety to the accompaniment.
Refer to “Pattern Variation (Sections)” on page 79.
DGX-630/YPG-635 Owner’s Manual 29
Playing Styles
Styles Are More Fun When You Understand Chords
Chords, created by playing multiple notes at the same time, are the basis for harmonic accompaniment.
In this section we’ll take a look at sequences of different chords played one after another, or “chord
sequences.” Since each chord has it’s own unique “color”—even if it’s different fingerings of the same
chord—the chords you choose to use in your chord progressions have a huge influence on the overall
feel of the music you play.
On page 28 you learned how to play colorful accompaniments using styles. Chord progressions are vital
to creating interesting accompaniments, and with a little chord know-how you should be able to take
your accompaniments to a new level.
On these pages we’ll introduce three easy-to-use chord progressions. Be sure to try them out with the
instrument’s accompaniment styles. The style will respond to the chord progression you play, effectively
creating a complete song.
Play the scores with the left hand.
Before playing the scores follow steps 1 through 3 of “Play Along with a Style” on page 28.
* The scores provided here are not standard song scores, but rather simplified scores that indicate which notes to play to
produce the chord progressions.
Split point
Play to the left of the split point.
Recommended Style
041 Euro Trance
—Dance music with simple chords—
Press the [INTRO/ENDING/rit.] button.
F
CGAm
This is a simple-but-effective chord progression. When you play through to the end of the score, start
again from the beginning. When you’re ready to stop playing press the [INTRO/ENDING/rit.] button
and the auto accompaniment function will create a perfect ending.
30 DGX-630/YPG-635 Owner’s Manual
Loading...
+ 124 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.