Yamaha XV19CTFE(C) Owners Manual
Read this manual carefully before operating this vehicle.
OWNER’S MANUAL
LIT-11626-27-17
Stratoliner Deluxe
XV19CTFE(C)
2BY-28199-11
EAU10042
Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
INTRODUCTION
WARNING
EAU10083
Congratulations on your purchase of the Yamaha XV19CTFE(C). This model is the result of Yamaha’s vast experience in
the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you
have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at
the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.
Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS” booklet carefully before operating
this motorcycle. Do not attempt to operate this motorcycle until you have attained adequate knowledge of its controls and operating features. Regular inspections and careful maintenance, along with good operating techniques,
will help ensure that you safely enjoy the capabilities and reliability of this motorcycle.
EWA10011
IMPORTANT MANUAL INFORMATION
WARNING
NOTICE
TIP
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
A NOTICE indicates special precautions that must be taken to avoid damage to the
vehicle or other property.
A TIP provides key information to make procedures easier or clearer.
*Product and specifications are subject to change without notice.
EAU10133
IMPORTANT MANUAL INFORMATION
XV19CTFE(C)
OWNER’S MANUAL
©2013 by Yamaha Motor Corporation, U.S.A.
1st edition, February 2013
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan.
P/N LIT-11626-27-17
EAU10193
TABLE OF CONTENTS
LOCATION OF IMPORTANT
LABELS .............................................1-1
SAFETY INFORMATION ..................2-1
DESCRIPTION ..................................3-1
Left view ..........................................3-1
Right view........................................3-2
Controls and instruments.................3-3
INSTRUMENT AND CONTROL
FUNCTIONS .......................................4-1
Main switch/steering lock ................4-1
Indicator lights and warning
lights ............................................4-2
Multi-function meter unit .................4-3
Handlebar switches ........................4-8
Clutch lever .....................................4-9
Shift pedal .....................................4-10
Brake lever ...................................4-10
Brake pedal ..................................4-10
Audio and navigation systems
(accessory) ................................4-11
Fuel tank cap ................................4-16
Fuel ...............................................4-17
Fuel tank breather/overflow
hose ..........................................4-18
Catalytic converter ........................4-19
Rider seat .....................................4-19
Helmet holder ...............................4-20
Sidecases (accessory) ..................4-21
Adjusting the shock absorber
assembly ...................................4-23
EXUP system ...............................4-25
Sidestand .....................................4-25
Ignition circuit cut-off system ........ 4-26
FOR YOUR SAFETY –
PRE-OPERATION CHECKS .............5-1
OPERATION AND IMPORTANT
RIDING POINTS.................................6-1
Starting the engine .........................6-1
Shifting ...........................................6-2
Engine break-in ..............................6-3
Parking ...........................................6-4
PERIODIC MAINTENANCE AND
ADJUSTMENT ................................... 7-1
Owner’s tool kit ...............................7-2
Periodic maintenance chart for the
emission control system ............. 7-3
General maintenance and
lubrication chart ..........................7-5
Checking the spark plugs ............... 7-9
Canister (for California only) ........ 7-10
Engine oil and oil filter cartridge ... 7-10
Transfer case oil ...........................7-13
Air filter element ........................... 7-14
Checking the throttle grip free
play ...........................................7-14
Valve clearance ............................ 7-14
Tires ............................................. 7-15
Cast wheels ................................. 7-16
Clutch lever .................................. 7-17
Checking the brake lever free
play ........................................... 7-17
Brake light switches ..................... 7-18
Checking the front and rear brake
pads .......................................... 7-18
Checking the brake and clutch
fluid levels ................................. 7-19
Changing the brake and clutch
fluids ......................................... 7-20
Drive belt slack ............................ 7-20
Checking and lubricating the
cables ....................................... 7-21
Checking and lubricating the
throttle grip and cable ............... 7-22
Checking and lubricating the
brake and shift pedals .............. 7-22
Checking and lubricating the
brake and clutch levers ............ 7-23
Checking and lubricating the
sidestand .................................. 7-23
Lubricating the rear suspension ... 7-24
Checking the front fork ................. 7-24
Checking the steering .................. 7-25
Checking the wheel bearings ....... 7-25
Battery ......................................... 7-25
Replacing the fuses ..................... 7-27
Replacing a headlight bulb .......... 7-28
Tail/brake light ............................. 7-28
Replacing a turn signal light
bulb ...........................................7-29
License plate light .........................7-29
Supporting the motorcycle ............7-29
Troubleshooting ............................7-30
Troubleshooting chart ...................7-31
MOTORCYCLE CARE AND
STORAGE ..........................................8-1
Matte color caution .........................8-1
Care ................................................8-1
Storage ...........................................8-4
SPECIFICATIONS .............................9-1
CONSUMER INFORMATION...........10-1
Identification numbers ..................10-1
Reporting safety defects ...............10-3
Motorcycle noise regulation ..........10-4
Maintenance record ......................10-5
YAMAHA MOTOR
CORPORATION, U.S.A.
STREET AND ENDURO
MOTORCYCLE LIMITED
WARRANTY .............................10-7
YAMAHA EXTENDED SERVICE
(Y.E.S.) .....................................10-9
STRATOLINER DELUXE AUDIO
SYSTEM LIMITED
WARRANTY ...........................10-11
TABLE OF CONTENTS
LOCATION OF IMPORTANT LABELS
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of
your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label
1
is available from your Yamaha dealer.
EAU10384
1 2,3,4 5
6
7,8
1-1
LOCATION OF IMPORTANT LABELS
NOTICE
• Cleaning with alkaline or acid cleaner,
gasoline or solvent will damage windshield.
• Use neutral detergent.
2C5-F815K-00
TIRE INFORMATION
Cold tire normal pressure should be set
as follows.
• Up to 90 kg (198 lbs) load
FRONT
REAR
: 250 kPa, (2.50 kgf/cm²), 36 psi
: 280 kPa, (2.80 kgf/cm²), 41 psi
• 90kg (198 lbs) ~ maximum load
FRONT
REAR
: 250 kPa, (2.50 kgf/cm²), 36 psi
: 280 kPa, (2.80 kgf/cm²), 41 psi
1D7-21668-00
VACUUM HOSE ROUTING
34B-21684-00
INTAKE MANIFOLD
PRESS. SENSOR
5RU-21686-00
EMISSION HOSE ROUTING
THROTTLE BODY
CANISTER
ATMOSPHERE
FUEL TANK
12
3 California only
4 California only
5
6
1
1-2
LOCATION OF IMPORTANT LABELS
7 8
1
1-3
SAFETY INFORMATION
EAU1028A
Be a Responsible Owner
As the vehicle’s owner, you are responsible for the safe and proper operation
of your motorcycle.
Motorcycles are single-track vehicles.
Their safe use and operation are dependent upon the use of proper riding
techniques as well as the expertise of
the operator. Every operator should
know the following requirements before
riding this motorcycle.
He or she should:
● Obtain thorough instructions from
a competent source on all aspects
of motorcycle operation.
● Observe the warnings and mainte-
nance requirements in this Owner’s Manual.
● Obtain qualified training in safe
and proper riding techniques.
● Obtain professional technical ser-
vice as indicated in this Owner’s
Manual and/or when made necessary by mechanical conditions.
● Never operate a motorcycle with-
out proper training or instruction.
Take a training course. Beginners
should receive training from a certified instructor. Contact an authorized motorcycle dealer to find out
about the training courses nearest
you.
Safe Riding
Perform the pre-operation checks each
time you use the vehicle to make sure it
is in safe operating condition. Failure to
inspect or maintain the vehicle properly
increases the possibility of an accident
or equipment damage. See page 5-1
for a list of pre-operation checks.
● This motorcycle is designed to car-
ry the operator and a passenger.
● The failure of motorists to detect
and recognize motorcycles in traffic is the predominating cause of
automobile/motorcycle accidents.
Many accidents have been caused
by an automobile driver who did
not see the motorcycle. Making
yourself conspicuous appears to
be very effective in reducing the
chance of this type of accident.
Therefore:
• Wear a brightly colored jacket.
• Use extra caution when you are
approaching and passing
through intersections, since intersections are the most likely
places for motorcycle accidents
to occur.
• Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
• Never maintain a motorcycle
without proper knowledge. Contact an authorized motorcycle
dealer to inform you on basic
motorcycle maintenance. Certain maintenance can only be
carried out by certified staff.
2
2-1
SAFETY INFORMATION
● Many accidents involve inexperi-
enced operators. In fact, many operators who have been involved in
accidents do not even have a current motorcycle license.
2
• Make sure that you are qualified
and that you only lend your motorcycle to other qualified operators.
• Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
• We recommend that you practice riding your motorcycle
where there is no traffic until you
have become thoroughly familiar with the motorcycle and all of
its controls.
● Many accidents have been caused
by error of the motorcycle operator. A typical error made by the operator is veering wide on a turn
due to excessive speed or undercornering (insufficient lean angle
for the speed).
• Always obey the speed limit and
never travel faster than warranted by road and traffic conditions.
• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
● The posture of the operator and
passenger is important for proper
control.
• The operator should keep both
hands on the handlebar and
both feet on the operator footrests during operation to maintain control of the motorcycle.
• The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
● Never ride under the influence of
alcohol or other drugs.
● This motorcycle is designed for on-
road use only. It is not suitable for
off-road use.
Protective Apparel
The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the
single most critical factor in the prevention or reduction of head injuries.
● Always wear an approved helmet.
● Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
● The use of a jacket, heavy boots,
trousers, gloves, etc., is effective in
preventing or reducing abrasions
or lacerations.
● Never wear loose-fitting clothes,
otherwise they could catch on the
control levers, footrests, or wheels
and cause injury or an accident.
● Always wear protective clothing
that covers your legs, ankles, and
feet. The engine or exhaust system become very hot during or after operation and can cause burns.
● A passenger should also observe
the above precautions.
2-2
SAFETY INFORMATION
Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbon
monoxide, a deadly gas. Breathing carbon monoxide can cause headaches,
dizziness, drowsiness, nausea, confusion, and eventually death.
Carbon Monoxide is a colorless, odorless, tasteless gas which may be
present even if you do not see or smell
any engine exhaust. Deadly levels of
carbon monoxide can collect rapidly
and you can quickly be overcome and
unable to save yourself. Also, deadly
levels of carbon monoxide can linger
for hours or days in enclosed or poorly
ventilated areas. If you experience any
symptoms of carbon monoxide poisoning, leave the area immediately, get
fresh air, and SEEK MEDICAL TREATMENT.
● Do not run engine indoors. Even if
you try to ventilate engine exhaust
with fans or open windows and
doors, carbon monoxide can rapidly reach dangerous levels.
● Do not run engine in poorly venti-
lated or partially enclosed areas
such as barns, garages, or carports.
● Do not run engine outdoors where
engine exhaust can be drawn into
a building through openings such
as windows and doors.
Loading
Adding accessories or cargo to your
motorcycle can adversely affect stability and handling if the weight distribution
of the motorcycle is changed. To avoid
the possibility of an accident, use extreme caution when adding cargo or
accessories to your motorcycle. Use
extra care when riding a motorcycle
that has added cargo or accessories.
Here, along with the information about
accessories below, are some general
guidelines to follow if loading cargo to
your motorcycle:
The total weight of the operator, passenger, accessories and cargo must
not exceed the maximum load limit.
Operation of an overloaded vehicle
could cause an accident.
Maximum load:
181 kg (399 lb)
2-3
When loading within this weight limit,
keep the following in mind:
● Cargo and accessory weight
should be kept as low and close to
the motorcycle as possible. Securely pack your heaviest items as
close to the center of the vehicle as
possible and make sure to distribute the weight as evenly as possible on both sides of the motorcycle
to minimize imbalance or instability.
● Shifting weights can create a sud-
den imbalance. Make sure that accessories and cargo are securely
attached to the motorcycle before
riding. Check accessory mounts
and cargo restraints frequently.
• Properly adjust the suspension
for your load (suspension-adjustable models only), and
check the condition and pressure of your tires.
• Never attach any large or heavy
items to the handlebar, front
fork, or front fender. These
items, including such cargo as
sleeping bags, duffel bags, or
2
SAFETY INFORMATION
tents, can create unstable handling or a slow steering response.
● This vehicle is not designed to
pull a trailer or to be attached to
2
a sidecar.
Genuine Yamaha Accessories
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are available only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection to
Yamaha manufacture parts and accessories or offer other modifications for
Yamaha vehicles. Yamaha is not in a
position to test the products that these
aftermarket companies produce.
Therefore, Yamaha can neither endorse nor recommend the use of accessories not sold by Yamaha or
modifications not specifically recommended by Yamaha, even if sold and
installed by a Yamaha dealer.
Aftermarket Parts, Accessories, and
Modifications
While you may find aftermarket products similar in design and quality to
genuine Yamaha accessories, recognize that some aftermarket accessories
or modifications are not suitable because of potential safety hazards to you
or others. Installing aftermarket products or having other modifications performed to your vehicle that change any
of the vehicle’s design or operation
characteristics can put you and others
at greater risk of serious injury or death.
You are responsible for injuries related
to changes in the vehicle.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
● Never install accessories or carry
cargo that would impair the performance of your motorcycle. Carefully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
clearance or cornering clearance,
limit suspension travel, steering
travel or control operation, or obscure lights or reflectors.
• Accessories fitted to the handlebar or the front fork area can
create instability due to improper
weight distribution or aerodynamic changes. If accessories
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.
• Bulky or large accessories may
seriously affect the stability of
the motorcycle due to aerodynamic effects. Wind may attempt to lift the motorcycle, or
the motorcycle may become unstable in cross winds. These accessories may also cause
instability when passing or being
passed by large vehicles.
• Certain accessories can displace the operator from his or
her normal riding position. This
improper position limits the freedom of movement of the opera-
2-4
SAFETY INFORMATION
tor and may limit control ability,
therefore, such accessories are
not recommended.
● Use caution when adding electri-
cal accessories. If electrical accessories exceed the capacity of the
motorcycle’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
Aftermarket Tires and Rims
The tires and rims that came with your
motorcycle were designed to match the
performance capabilities and to provide
the best combination of handling, braking, and comfort. Other tires, rims, sizes, and combinations may not be
appropriate. Refer to page 7-15 for tire
specifications and more information on
replacing your tires.
Transporting the Motorcycle
Be sure to observe following instructions before transporting the motorcycle in another vehicle.
● Remove all loose items from the
motorcycle.
● Check that the fuel cock (if
equipped) is in the “OFF” position
and that there are no fuel leaks.
● Point the front wheel straight
ahead on the trailer or in the truck
bed, and choke it in a rail to prevent movement.
● Shift the transmission in gear (for
models with a manual transmission).
● Secure the motorcycle with tie-
downs or suitable straps that are
attached to solid parts of the motorcycle, such as the frame or upper front fork triple clamp (and not,
for example, to rubber-mounted
handlebars or turn signals, or parts
that could break). Choose the location for the straps carefully so
the straps will not rub against
painted surfaces during transport.
● The suspension should be com-
pressed somewhat by the tiedowns, if possible, so that the motorcycle will not bounce excessively during transport.
2
2-5
DESCRIPTION
12 3456 7 8 9
12 11 10
Left view
3
EAU10410
1. Headlight (page 7-28)
2. Cowling (accessory)
3. Seat lock (page 4-19)
4. Main fuse (page 7-27)
5. Battery (page 7-25)
6. Owner’s tool kit (page 7-2)
7. Sidecase (accessory) (page 4-21)
8. License plate light (page 7-29)
9. Tail/brake light (page 7-28)
10.Engine oil drain bolt B (crankcase) (page 7-10)
11.Engine oil drain bolt A (crankcase) (page 7-10)
12.Shift pedal (page 4-10)
3-1
Right view
1 2,3,4 5 6
10,11 9 8 7
DESCRIPTION
EAU10420
3
1. Helmet holder (page 4-20)
2. Fuel injection system fuse (page 7-27)
3. Rear brake fluid reservoir (page 7-19)
4. Fuse box (page 7-27)
5. Engine oil filler cap (page 7-10)
6. Fuel tank cap (page 4-16)
7. Brake pedal (page 4-10)
8. Rear brake light switch (page 7-18)
9. Engine oil filter cartridge (page 7-10)
10.Engine oil drain bolt (oil tank) (page 7-10)
11.Shock absorber assembly spring preload adjusting nut (page 4-23)
3-2
DESCRIPTION
132 45687 9 10 11 12
Controls and instruments
3
EAU10430
1. Clutch lever (page 4-9)
2. Audio system control unit (accessory) (page 4-11)
3. Left handlebar switches (page 4-8)
4. Clutch fluid reservoir (page 7-19)
5. Multi-function meter unit (page 4-3)
6. Navigation module (accessory) (page 4-11)
7. Main switch/steering lock (page 4-1)
®
8. iPod
/media player connector (accessory) (page 4-11)
9. Front brake fluid reservoir (page 7-19)
10.Right handlebar switches (page 4-8)
11.Throttle grip (page 7-14)
12.Brake lever (page 4-10)
3-3
INSTRUMENT AND CONTROL FUNCTIONS
TIP
WARNING
12
Main switch/steering lock
The main switch/steering lock is located under the main switch/steering lock
cover. To access the main
switch/steering lock, slide the cover forward.
1. Main switch/steering lock cover
2. Main switch/steering lock
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
EAU38390
ON
EAU10540
All electrical circuits are supplied with
power, and the meter lighting, taillight,
license plate light and position lights
come on, and the engine can be started. The key cannot be removed.
The headlight comes on automatically
when the engine is started and stays on
until the key is turned to “OFF”, even if
the engine stalls.
EAU10661
OFF
All electrical systems are off. The key
can be removed.
EWA10061
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident.
LOCK
EAU10684
The steering is locked, and all electrical
systems are off. The key can be removed.
To lock the steering
4
1. Push.
2. Turn.
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
4-1
INSTRUMENT AND CONTROL FUNCTIONS
TIP
12
To unlock the steering
4
1. Push.
2. Turn.
Push the key in, and then turn it to
“OFF” while still pushing it.
EAU49393
Indicator lights and warning lights
1. Neutral indicator light “ ”
2. High beam indicator light “ ”
3. Right turn signal indicator light “ ”
4. Left turn signal indicator light “ ”
5. Engine trouble warning light “ ”
6. Fuel level warning light “ ”
EAU11030
Turn signal indicator lights “ ”
and “ ”
The corresponding indicator light flashes when the turn signal switch is
pushed to the left or right.
EAU11060
Neutral indicator light “ ”
This indicator light comes on when the
transmission is in the neutral position.
High beam indicator light “ ”
EAU11080
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU11366
Fuel level warning light “ ”
This warning light comes on when the
fuel level drops below approximately
3.0 L (0.79 US gal, 0.66 Imp.gal). When
this occurs, refuel as soon as possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
This model is also equipped with a selfdiagnosis device for the fuel level detection circuit. If a problem is detected
in the fuel level detection circuit, the following cycle will be repeated until the
malfunction is corrected: The fuel level
warning light will flash eight times, and
4-2
INSTRUMENT AND CONTROL FUNCTIONS
WARNING
TIP
then go off for 3.0 seconds. If this occurs, have a Yamaha dealer check the
vehicle.
EAU11534
Engine trouble warning light “ ”
This warning light comes on or flashes
if a problem is detected in the electrical
circuit monitoring the engine. If this occurs, have a Yamaha dealer check the
self-diagnosis system. (See page 4-6
for an explanation of the self-diagnosis
device.)
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. The warning light should come
on for a few seconds, and then go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
EAU3842F
Multi-function meter unit
1. Speedometer
2. Fuel gauge
3. Odometer/tripmeter/fuel reserve tripmeter/clock
4. Tachometer
EWA12422
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
● a fuel gauge
● an odometer
● two tripmeters (which show the
distance traveled since they were
last set to zero)
● a fuel reserve tripmeter (which
shows the distance traveled on the
fuel reserve)
● a clock
● a self-diagnosis device
● a brightness control mode
● Be sure to turn the key to “ON” be-
fore using the “SELECT” and reset
switches, except for setting the
brightness control mode.
● To switch the odometer, the trip-
meters and the fuel reserve tripmeter displays between kilometers
and miles, press the “SELECT”
switch for at least two seconds.
4
The multi-function meter unit is
equipped with the following:
● a speedometer
● a tachometer
4-3
INSTRUMENT AND CONTROL FUNCTIONS
NOTICE
1. “SELECT” switch
4
1. Reset switch
Speedometer
1. Speedometer 1. Tachometer
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then return
to zero in order to test the electrical circuit.
Tachometer
2. Tachometer red zone
The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the tachometer needle will sweep once
across the r/min range and then return
to zero r/min in order to test the electrical circuit.
Do not operate the engine in the tachometer red zone.
Red zone: 5000 r/min and above
ECA10031
4-4
INSTRUMENT AND CONTROL FUNCTIONS
TIP
Fuel gauge
1. Fuel gauge
The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the needle reaches
“E”, approximately 3.0 L (0.79 US gal,
0.66 Imp.gal) remain in the fuel tank. If
this occurs, refuel as soon as possible.
When the key is turned to “ON”, the fuel
gauge needle will sweep once across
the fuel level range and then return to
the current amount in order to test the
electrical circuit.
After refueling, the fuel gauge does not
indicate the correct fuel level unless the
vehicle speed has exceeded 5 km/h (3
mi/h).
Odometer, tripmeters, fuel reserve
tripmeter and clock
1. Odometer/tripmeter/fuel reserve tripmeter/clock
Push the “SELECT” switch to switch
the display between the odometer
mode “ODO”, the tripmeter modes
“TRIP 1” and “TRIP 2” and the clock
mode in the following order:
ODO → TRIP 1 → TRIP 2 → Clock →
ODO
If the fuel level warning light comes on
(see page 4-2), the odometer display
will automatically change to the fuel reserve tripmeter mode “F-TRIP” and
start counting the distance traveled
from that point. In that case, push the
“SELECT” switch to switch the display
between the various tripmeter, odometer, and clock modes in the following order:
F-TRIP → TRIP 1 → TRIP 2 → Clock
→ ODO → F-TRIP
To reset a tripmeter, select it by pushing the “SELECT” switch, and then
push the reset switch for at least one
second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically, and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).
4
4-5
INSTRUMENT AND CONTROL FUNCTIONS
NOTICE
2
1
To set the clock
4
1. Clock 1. Engine trouble warning light “ ”
1. Push the “SELECT” switch to
change the display to the clock
mode.
2. Push the “SELECT” and reset
switches together for at least two
seconds.
3. When the hour digits start flashing,
push the reset switch to set the
hours.
4. Push the “SELECT” switch, and
the minute digits will start flashing.
5. Push the reset switch to set the
minutes.
Self-diagnosis device
2. Error code display
This model is equipped with a self-diagnosis device for various electrical circuits.
If a problem is detected in any of those
circuits, the engine trouble warning light
will come on or flash, and the odometer/tripmeter/clock display will indicate
an error code.
If the odometer/tripmeter/clock display
indicates any error codes, note the
code number, and then have a Yamaha
dealer check the vehicle.
6. Push the “SELECT” switch and
then release it to start the clock.
ECA11590
If the display indicates an error
code, the vehicle should be checked
as soon as possible in order to avoid
engine damage.
Brightness control mode
1. Multi-function meter unit panel
2. LCD
3. Speedometer needle
4. Tachometer needle
5. Fuel gauge needle
The brightness can be adjusted for the
following:
● the multi-function meter unit panel
(item number “1”)
● the LCD (item number “2”)
4-6
INSTRUMENT AND CONTROL FUNCTIONS
● the speedometer, tachometer, and
the fuel gauge needles (item num-
ber “3”)
Select the brightness control mode as
follows.
1. Turn the key to “OFF”.
2. Push and hold the “SELECT”
switch.
3. Turn the key to “ON”, and then release the “SELECT” switch after
five seconds.
Item number “1” is displayed.
1. Multi-function meter unit panel
2. Item number “1”
3. Brightness level display
4. Adjust the multi-function meter unit
panel brightness level by pushing
the reset switch.
5. Push the “SELECT” switch to select the LCD.
Item number “2” is displayed.
Adjust the LCD brightness level by
pushing the reset switch.
1. LCD
2. Item number “2”
3. Brightness level display
6. Push the “SELECT” switch to select the speedometer, tachometer,
and the fuel gauge needles.
Item number “3” is displayed.
Adjust the brightness level of the
speedometer, tachometer, and the
fuel gauge needles by pushing the
reset switch.
1. Speedometer needle
2. Tachometer needle
3. Fuel gauge needle
4. Item number “3”
5. Brightness level display
7. Push the “SELECT” switch.
The odometer/tripmeter/clock display will return to the prior mode.
4
4-7
INSTRUMENT AND CONTROL FUNCTIONS
TIP
Handlebar switches
Left
4
1. Dimmer switch “ / ”
2. Turn signal switch “ / ”
3. Horn switch “ ”
1. “SELECT” switch
EAU1234C
Right
1. Engine stop switch “ / ”
2. Light switch (for optional lights) “ ”
3. Start switch “ ”
EAU12400
Dimmer switch “ / ”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
EAU12430
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When released, the switch returns to the center
position.
Since this model is equipped with a
self-canceling system, the turn signal
lights will self-cancel after the vehicle
has traveled both about 150 m (490 ft)
4-8
and for approximately 15 seconds.
However, the turn signal lights can also
be canceled manually by pushing the
switch in after it has returned to the center position.
The self-canceling system only operates when the vehicle is moving, so that
the turn signal lights will not self-cancel
while you are stopped at an intersection.
EAU12500
Horn switch “ ”
Press this switch to sound the horn.
EAU12660
Engine stop switch “ / ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergency, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU38331
Light switch (for optional
lights) “ ”
This model can be equipped with optional lights available at a Yamaha
dealer.
INSTRUMENT AND CONTROL FUNCTIONS
NOTICE
Push this switch to the left to turn the
optional lights on and to the right to turn
them off.
ECA15321
Do not install a bulb which exceeds
12 V, 35 W in either light, otherwise
the headlight fuse may blow or the
battery may discharge.
EAU12711
Start switch “ ”
Push this switch to crank the engine
with the starter. See page 6-1 for starting instructions prior to starting the engine.
EAU41700
The engine trouble warning light will
come on when the key is turned to “ON”
and the start switch is pushed, but this
does not indicate a malfunction.
EAU44602
“SELECT” switch
This switch is used to perform selections in the odometer and tripmeters, to
set the clock and to set the brightness
control mode of the multi-function
meter unit.
See “Multi-function meter unit” on page
4-3 for detailed information.
EAU12820
Clutch lever
4
1. Clutch lever
The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handlebar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the ignition circuit cut-off system. (See page
4-26.)
4-9
INSTRUMENT AND CONTROL FUNCTIONS
TIP
Shift pedal
4
1. Shift pedal
2. Neutral position
The shift pedal is located on the left
side of the motorcycle and is used in
combination with the clutch lever when
shifting the gears of the 5-speed constant-mesh transmission equipped on
this motorcycle.
Use your toes or heel to shift up and
your toes to shift down.
EAU12881
EAU12891
Brake lever
1. Brake lever 1. Brake pedal
The brake lever is located on the right
side of the handlebar. To apply the front
brake, pull the lever toward the throttle
Brake pedal
The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.
grip.
EAU12941
4-10
INSTRUMENT AND CONTROL FUNCTIONS
WARNING
NOTICE
EAU53622
Audio and navigation systems (accessory)
EWA16200
● It is dangerous to operate the
audio system controls, navigation system or your portable
media player while riding. Never
take your hands off the handlebars while riding.
● Keep the volume at a low
enough level to be aware of traffic conditions and ensure safety.
ECA17880
● Do not operate the audio sys-
tem or navigation system for a
long period of time when the engine is not running as the battery may discharge.
● The control unit and speakers
are water-resistant. However, it
is good practice to cover them
with plastic bags when washing
the vehicle.
● The media player connector in
the cowling media player compartment is not water-resistant.
Be sure to keep the connector
covered with the rubber cover
provided when not in use. It is
good practice to wrap the connector in a plastic bag when
washing the vehicle or in wet
weather.
● When cleaning the control unit,
use a neutral (mild) detergent.
Never use strong abrasive
cleaning products, fuel (gasoline), thinner, etc.
2
3
1
44
1. Control unit (accessory)
2. Cowling media player compartment (accessory)
3. Navigation module (accessory)
4. Speakers (accessory)
The audio system on this vehicle has a
two-channel stereo amplifier, with a
handlebar-mounted control unit, that
controls and charges an iPod device*
connected to the 30-pin connector in
the cowling media player compartment.
It features Automatic Volume Control
(AVC) that adjusts volume as vehicle
speed increases or decreases.
* Compatibility information:
● Made for:
• iPod touch
ations)
®
(1st and 2nd gener-
4
4-11
INSTRUMENT AND CONTROL FUNCTIONS
TIP
• iPod nano
®
(1st, 2nd, 3rd, 4th,
and 5th generation)
• iPod classic
®
• iPod with video
The following instructions assume
that a fully compatible device is being used.
“Made for iPod” means that an
electronic accessory has been designed to connect specifically to
4
iPod and has been certified by the
developer to meet Apple performance standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod may affect wireless performance.
● An accessory cable is available
from your Yamaha dealer to connect other types of portable media
players through their headphone
jacks. You can use the handlebarmounted control unit to adjust volume, but track selection and battery-charging functions will not
operate.
The navigation system on this vehicle
features a Garmin
®
zumo® 665 Navigation Module which also has the ability
to receive XM Radio
®
signals (subscription required) or play audio files
contained on an SD™ card. See page
4-16 for more information about using
the Garmin zumo with this vehicle. Refer to the documentation included in the
package for your Garmin navigation
module (supplied with the vehicle at the
time of purchase).
The navigation system on this vehicle
has two modes: iPod priority mode, and
dedicated Garmin mode.
In iPod priority mode, the system gives
priority to iPod playback. If the navigation system is also in operation, it will
temporarily mute iPod playback whenever it gives a voice prompt for navigation.
Do not attempt to operate XM Radio or
use the SD card playback function
when in iPod priority mode. The system
will constantly switch back and forth, interrupting iPod playback, making listening to any program difficult.
In Garmin mode, the navigation module
is the dedicated audio source, including
XM Radio or SD card audio input, if
used. Any voice prompts from the navigation system will temporarily mute
any audio playing. If an iPod device is
connected, its playback is paused in
this mode.
To select the desired mode, press and
hold the TRACK “ ” button (about 2
seconds) until you hear beeps. Three
short beeps indicate that the system is
in iPod priority mode. Two longer beeps
indicate that the system is in dedicated
Garmin mode. To switch modes, press
and hold the TRACK “ ” button again
(about 2 seconds).
iPod, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in
the U.S. and other countries. Garmin
and zumo are trademarks of Garmin
Ltd. XM Radio is a registered trademark of Sirius XM Radio Inc. SD is a
trademark of the SD Association.
4-12
Loading...