Yamaha TW200 ET 2005 Owner's manual
OWNER’S MANUAL
TW200ET
3XT-28199-2E
INTRODUCTION
EAU10100
Welcome to the Yamaha world of motorcycling!
As the owner of the TW200E, you are benefiting from Yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
Please take the time to read this manual thoroughly, so as to enjoy all advantages of your TW200E. The owner’s manual
does not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourself and
others from trouble and injury.
In addition, the many tips given in this manual will help keep your motorcycle in the best possible condition. If you have any
further questions, do not hesitate to contact your Yamaha dealer.
The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!
IMPORTANT MANUAL INFORMATION
Particularly important information is distinguished in this manual by the following notations:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
Failure to follow WARNING instructions could result in severe injury or death to the
WARNING
CAUTION:
motorcycle operator, a bystander, or a person inspecting or repairing the motorcycle.
A CAUTION indicates special precautions that must be taken to avoid damage to
the motorcycle.
EAU10150
NOTE:
A NOTE provides key information to make procedures easier or clearer.
NOTE:
●
This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle
is subsequently sold.
●
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your motorcycle
and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
WARNING
PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE.
EWA10030
IMPORTANT MANUAL INFORMATION
TW200ET
OWNER’S MANUAL
©2004 by Yamaha Motor Co., Ltd.
1st edition, April 2004
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in Japan.
EAU10200
TABLE OF CONTENTS
SAFETY INFORMATION
Location of important labels .............1-5
DESCRIPTION
Left view ...........................................2-1
Right view .........................................2-2
Controls and instruments..................2-3
INSTRUMENT AND CONTROL
FUNCTIONS
Main switch/steering lock .................3-1
Indicator lights .................................3-2
Speedometer unit ............................3-2
Handlebar switches .........................3-3
Clutch lever ......................................3-4
Shift pedal ........................................3-4
Brake lever ......................................3-4
Brake pedal .....................................3-5
Fuel tank cap ...................................3-5
Fuel ..................................................3-6
Fuel cock .........................................3-6
Starter (choke) knob “1” .................3-7
Kickstarter ........................................3-8
Seat .................................................3-8
Helmet holder ..................................3-9
Shock absorber ...............................3-9
Carrier ..............................................3-9
Luggage strap holders ...................3-10
Sidestand .......................................3-10
Ignition circuit cut-off system .........3-11
...................................2-1
........................................3-1
...................1-1
PRE-OPERATION CHECKS
Pre-operation check list ................... 4-2
OPERATION AND IMPORTANT
RIDING POINTS
Starting a cold engine ..................... 5-1
Starting a warm engine ...................5-2
Shifting ............................................ 5-2
Tips for reducing fuel
consumption ................................ 5-3
Engine break-in ...............................5-3
Parking ............................................ 5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR
Owner’s tool kit ................................ 6-1
Periodic maintenance and
lubrication chart ........................... 6-2
Removing and installing the cowling
and panels ...................................6-5
Checking the spark plug .................. 6-6
Engine oil and oil filter element .......6-8
Cleaning the air filter element and
check hose ................................. 6-10
Adjusting the carburetor ................6-12
Adjusting the engine idling
speed ......................................... 6-12
Adjusting the throttle cable free
play ............................................ 6-13
Adjusting the valve clearance ....... 6-13
Tires .............................................. 6-13
.................................. 5-1
.................................. 6-1
.............. 4-1
Spoke wheels ............................... 6-15
Adjusting the clutch lever free
play ............................................ 6-16
Adjusting the brake lever free
play ............................................ 6-17
Adjusting the brake pedal position
and free play .............................. 6-17
Adjusting the rear brake light
switch ......................................... 6-19
Checking the front brake pads and
rear brake shoes ........................ 6-19
Checking the front brake fluid
level ........................................... 6-20
Changing the brake fluid ............... 6-21
Drive chain slack ........................... 6-21
Lubricating the drive chain ............ 6-23
Checking and lubricating the
cables ........................................ 6-23
Checking and lubricating the
throttle grip and cable ................ 6-24
Checking and lubricating the
brake and shift pedals ............... 6-24
Checking and lubricating the
brake and clutch levers .............. 6-24
Checking and lubricating the
sidestand ................................... 6-25
Lubricating the rear suspension .... 6-25
Checking the front fork .................. 6-25
Checking the steering ................... 6-26
Checking the wheel bearings ........ 6-27
Battery ........................................... 6-27
Replacing the fuse ......................... 6-29
Replacing the headlight bulb .........6-30
Replacing the tail/brake light
bulb ............................................6-32
Replacing a turn signal light
bulb ............................................6-32
Supporting the motorcycle ............. 6-33
Front wheel .................................... 6-34
Rear wheel ....................................6-35
Troubleshooting .............................6-36
Troubleshooting chart .................... 6-37
MOTORCYCLE CARE AND
STORAGE
Care .................................................7-1
Storage ............................................7-3
SPECIFICATIONS ..............................8-1
...........................................7-1
TABLE OF CONTENTS
CONSUMER INFORMATION
Identification numbers .....................9-1
Motorcycle noise regulation
(for Australia) ................................9-2
..............9-1
SAFETY INFORMATION
MOTORCYCLES ARE SINGLE
TRACK VEHICLES. THEIR SAFE
USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER
1
RIDING TECHNIQUES AS WELL AS
THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD
KNOW THE FOLLOWING REQUIREMENTS BEFORE RIDING THIS MOTORCYCLE.
HE OR SHE SHOULD:
●
OBTAIN THOROUGH INSTRUC-
TIONS FROM A COMPETENT
SOURCE ON ALL ASPECTS OF
MOTORCYCLE OPERATION.
●
OBSERVE THE WARNINGS
AND MAINTENANCE REQUIRE-
MENTS IN THE OWNER’S MAN-
UAL.
●
OBTAIN QUALIFIED TRAINING
IN SAFE AND PROPER RIDING
TECHNIQUES.
●
OBTAIN PROFESSIONAL TECH-
NICAL SERVICE AS INDICATED
BY THE OWNER’S MANUAL
AND/OR WHEN MADE NECES-
EAU10310
SARY BY MECHANICAL CONDITIONS.
Safe riding
●
Always make pre-operation
checks. Careful checks may help
prevent an accident.
●
This motorcycle is designed to carry the operator and a passenger.
●
The failure of motorists to detect
and recognize motorcycles in traffic is the predominating cause of
automobile/motorcycle accidents.
Many accidents have been caused
by an automobile driver who did
not see the motorcycle. Making
yourself conspicuous appears to
be very effective in reducing the
chance of this type of accident.
●
Therefore:
●
Wear a brightly colored jacket.
●
Use extra caution when approaching and passing through
intersections, since intersections are the most likely places
for motorcycle accidents to occur.
●
Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
●
Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current motorcycle license.
●
Make sure that you are qualified
and that you only lend your motorcycle to other qualified operators.
●
Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
●
We recommend that you practice riding your motorcycle
where there is no traffic until you
have become thoroughly familiar with the motorcycle and all of
its controls.
●
Many accidents have been caused
by error of the motorcycle operator. A typical error made by the operator is veering wide on a turn
due to EXCESSIVE SPEED or un-
1-1
SAFETY INFORMATION
dercornering (insufficient lean angle for the speed).
●
Always obey the speed limit and
never travel faster than warranted by road and traffic conditions.
●
Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
●
The posture of the operator and
passenger is important for proper
control.
●
The operator should keep both
hands on the handlebar and
both feet on the operator footrests during operation to maintain control of the motorcycle.
●
The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
●
Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
●
Never ride under the influence of
alcohol or other drugs.
Protective apparel
The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the
single most critical factor in the prevention or reduction of head injuries.
●
Always wear an approved helmet.
●
Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
●
The use of a jacket, heavy boots,
trousers, gloves, etc., is effective in
preventing or reducing abrasions
or lacerations.
●
Never wear loose-fitting clothes,
otherwise they could catch on the
control levers, footrests, or wheels
and cause injury or an accident.
●
Never touch the engine or exhaust
system during or after operation.
They become very hot and can
cause burns. Always wear protective clothing that covers your legs,
ankles, and feet.
●
Passengers should also observe
the precautions mentioned above.
Modifications
Modifications made to this motorcycle
not approved by Yamaha, or the removal of original equipment, may render the motorcycle unsafe for use and
may cause severe personal injury.
Modifications may also make your motorcycle illegal to use.
Loading and accessories
Adding accessories or cargo to your
motorcycle can adversely affect stability and handling if the weight distribution
of the motorcycle is changed. To avoid
the possibility of an accident, use extreme caution when adding cargo or
accessories to your motorcycle. Use
extra care when riding a motorcycle
that has added cargo or accessories.
Here are some general guidelines to
follow if loading cargo or adding accessories to your motorcycle:
Loading
The total weight of the operator, passenger, accessories and cargo must
1
1-2
SAFETY INFORMATION
not exceed the maximum load limit of
180 kg (397 lb). When loading within
this weight limit, keep the following in
mind:
1
●
Cargo and accessory weight
should be kept as low and close to
the motorcycle as possible. Make
sure to distribute the weight as
evenly as possible on both sides of
the motorcycle to minimize imbal-
ance or instability.
●
Shifting weights can create a sud-
den imbalance. Make sure that ac-
cessories and cargo are securely
attached to the motorcycle before
riding. Check accessory mounts
and cargo restraints frequently.
●
Never attach any large or heavy
items to the handlebar, front fork,
or front fender. These items, in-
cluding such cargo as sleeping
bags, duffel bags, or tents, can
create unstable handling or a slow
steering response.
Accessories
Genuine Yamaha accessories have
been specifically designed for use on
this motorcycle. Since Yamaha cannot
test all other accessories that may be
available, you must personally be responsible for the proper selection, installation and use of non-Yamaha
accessories. Use extreme caution
when selecting and installing any accessories.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
●
Never install accessories or carry
cargo that would impair the performance of your motorcycle. Carefully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
clearance or cornering clearance,
limit suspension travel, steering
travel or control operation, or obscure lights or reflectors.
●
Accessories fitted to the handlebar or the front fork area can
create instability due to improper
weight distribution or aerody-
namic changes. If accessories
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.
●
Bulky or large accessories may
seriously affect the stability of
the motorcycle due to aerodynamic effects. Wind may attempt to lift the motorcycle, or
the motorcycle may become unstable in cross winds. These accessories may also cause
instability when passing or being
passed by large vehicles.
●
Certain accessories can displace the operator from his or
her normal riding position. This
improper position limits the freedom of movement of the operator and may limit control ability,
therefore, such accessories are
not recommended.
●
Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the
1-3
SAFETY INFORMATION
motorcycle’s electrical system an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
Gasoline and exhaust gas
●
GASOLINE IS HIGHLY FLAMMABLE:
●
Always turn the engine off when
refueling.
●
Take care not to spill any gasoline on the engine or exhaust
system when refueling.
●
Never refuel while smoking or in
the vicinity of an open flame.
●
Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poisonous and may cause loss of
consciousness and death within a
short time. Always operate your
motorcycle in an area that has adequate ventilation.
●
Always turn the engine off before
leaving the motorcycle unattended
and remove the key from the main
switch. When parking the motorcy-
cle, note the following:
●
The engine and exhaust system
may be hot, therefore, park the
motorcycle in a place where pedestrians or children are not likely to touch these hot areas.
●
Do not park the motorcycle on a
slope or soft ground, otherwise it
may fall over.
●
Do not park the motorcycle near
a flammable source (e.g., a kerosene heater, or near an open
flame), otherwise it could catch
fire.
●
When transporting the motorcycle
in another vehicle, make sure that
it is kept upright and that the fuel
cock(s) are turned to “ON” or
“RES” (for vacuum type)/“OFF”
(for manual type). If the motorcycle
should lean over, gasoline may
leak out of the carburetor or fuel
tank.
●
If you should swallow any gasoline, inhale a lot of gasoline vapor,
or allow gasoline to get into your
eyes, see your doctor immediately. If any gasoline spills on your
skin or clothing, immediately wash
the affected area with soap and
water and change your clothes.
1
1-4
SAFETY INFORMATION
Location of important labels
Please read the following important labels carefully before operating this vehicle.
1
1
2
EAU10381
3
1-5
SAFETY INFORMATION
1
Before you operate this vehicle, read the owner’s manual.
Prima di usare il veicolo, leggete il manuale di istruzioni.
Lire le manuel du propri
Lesen Sie die Bedienungsanleitung bevor Sie dieses Fahrzeug fahren.
Antes de conducir este vehículo, lea el Manual del Propietario.
étaire avant d
’utiliser ce v
éhicule.
5PA-21568-00
2
4AA-22259-40
3
1
1-6
DESCRIPTION
Left view
EAU10410
1
2
3
4
5
6
7
8
1. Fuel cock (page 3-6)
2. Helmet holder (page 3-9)
3. Luggage strap holder (page 3-10)
9
4. Drive chain slack adjusting plate
5. Air filter element (page 6-10)
6. Starter (choke) knob (page 3-7)
7. Shift pedal (page 3-4)
1
6
2
3
457
2-1
Right view
DESCRIPTION
EAU10420
12
1. Carrier (page 3-9)
2. Battery (page 6-27)
3. Kickstarter (page 3-8)
4. Engine oil filter element (page 6-8)
5. Engine oil level check window (page 6-8)
6. Brake pedal (page 3-5)
7. Owner’s tool kit (page 6-1)
8. Fuse (page 6-29)
789
43
65
9. Luggage strap holder (page 3-10)
2
3
4
5
6
7
8
9
2-2
DESCRIPTION
Controls and instruments
EAU10430
1
2
3
4
5
6
7
8
1. Clutch lever (page 3-4)
2. Left handlebar switches (page 3-3)
3. Speedometer unit (page 3-2)
9
4. Main switch/steering lock (page 3-1)
5. Indicator lights (page 3-2)
6. Right handlebar switches (page 3-3)
7. Brake lever (page 3-4)
8. Throttle grip (page 6-13)
12 3 4
5
9. Fuel tank cap (page 3-5)
67
8
9
2-3
INSTRUMENT AND CONTROL FUNCTIONS
EAU10460
Main switch/steering lock
ON
OFF
LOCK
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
EAU10510
ON
All electrical systems are supplied with
power, and the headlight, meter lighting, taillight and position lights come
on, and the engine can be started. The
key cannot be removed.
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAU10710
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
To lock the steering
12
1. Push.
2. Release.
3. Turn.
3
Turn the handlebars all the way to the
left or right.
1. Push the key in from the “OFF” position, release it, and then turn it to
“LOCK”.
2. Remove the key.
3-1
To unlock the steering
Insert the key and turn it to “OFF”.
EWA10070
WARNING
Never turn the key to “LOCK” while
the motorcycle is moving.
2
3
4
5
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
4
2
3
1
Indicator lights
312
1
2
3
4
1. Turn signal indicator light “”
2. High beam indicator light “”
5
3. Neutral indicator light “”
6
Turn signal indicator light “”
This indicator light flashes when the
7
turn signal switch is pushed to the left or
right.
8
Neutral indicator light “”
9
This indicator light comes on when the
transmission is in the neutral position.
EAU10980
EAU11020
EAU11060
EAU11080
High beam indicator light “”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU11630
Speedometer unit
1. Speedometer
2. Odometer
3. Tripmeter
4. Reset knob
The speedometer unit is equipped with
a speedometer, an odometer and a
tripmeter. The speedometer shows
riding speed. The odometer shows the
total distance traveled. The tripmeter
shows the distance traveled since it
was last set to zero with the reset knob.
The tripmeter can be used to estimate
the distance that can be traveled with a
full tank of fuel. This information will enable you to plan future fuel stops.
3-2
INSTRUMENT AND CONTROL FUNCTIONS
Handlebar switches
Left
1
2
3
1. Dimmer switch “ / ”
2. Turn signal switch “ / ”
3. Horn switch “”
EAU12343
Right
1
2
1. Engine stop switch “ / ”
2. Start switch “”
EAU12400
Dimmer switch “ / ”
Set this switch to “” for the high
beam and to “” for the low beam.
EAU12460
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “”. To signal a left-hand
turn, push this switch to “”. When re-
leased, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has returned to the center position.
EAU12500
Horn switch “”
Press this switch to sound the horn.
EAU12660
Engine stop switch “ / ”
Set this switch to “” before starting
the engine. Set this switch to “” to
stop the engine in case of an emergency, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12710
Start switch “”
Push this switch to crank the engine
with the starter.
ECA10050
CAUTION:
See page 5-1 for starting instructions prior to starting the engine.
2
3
4
5
6
7
8
9
3-3
INSTRUMENT AND CONTROL FUNCTIONS
1
Clutch lever
1
1
2
3
4
1. Clutch lever
The clutch lever is located at the left
5
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
6
bar grip. To engage the clutch, release
the lever. The lever should be pulled
7
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
8
clutch switch, which is part of the ignition circuit cut-off system. (See
9
page 3-11.)
EAU12820
EAU12870
Shift pedal
5
4
3
2
N
1
1
1. Shift pedal
The shift pedal is located on the left
side of the engine and is used in combination with the clutch lever when
shifting the gears of the 5-speed constant-mesh transmission equipped on
this motorcycle.
EAU12890
Brake lever
1. Brake lever
The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handlebar grip.
3-4
INSTRUMENT AND CONTROL FUNCTIONS
EAU12941
Brake pedal
1
1. Brake pedal
The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.
Fuel tank cap
2
1
1. Fuel tank cap
2. Unlock.
To remove the fuel tank cap
1. Insert the key into the lock and turn
it 1/3 turn counterclockwise.
2. Turn the fuel tank cap 1/3 turn
counterclockwise and pull it off.
To install the fuel tank cap
1. Insert the fuel tank cap into the
tank opening with the key inserted
in the lock, and then turn the cap 1/
3 turn clockwise.
2. Turn the key 1/3 turn clockwise,
and then remove it.
EAU32280
NOTE:
The fuel tank cap cannot be installed
unless the key is in the lock. In addition,
the key cannot be removed if the cap is
not properly installed and locked.
EWA10120
WARNING
Make sure that the fuel tank cap is
properly closed and locked before
riding.
2
3
4
5
6
7
8
9
3-5
INSTRUMENT AND CONTROL FUNCTIONS
RES
ON
FUEL
OFF
1
Fuel
1
2
3
4
1. Fuel tank filler tube
2. Fuel level
5
Make sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
6
of the filler tube as shown.
7
8
9
WARNING
Do not overfill the fuel tank, oth-
●
erwise it may overflow when the
fuel warms up and expands.
Avoid spilling fuel on the hot en-
●
gine.
CAUTION:
Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
1
EAU13210
2
EWA10880
ECA10070
fuel may deteriorate painted surfaces or plastic parts.
EAU13330
Recommended fuel:
UNLEADED GASOLINE ONLY
Fuel tank capacity:
7.0 L (1.85 US gal) (1.54 Imp.gal)
Fuel reserve amount:
1.7 L (0.45 US gal) (0.37 Imp.gal)
ECA11400
CAUTION:
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.
Your Yamaha engine has been designed to use regular unleaded gasoline with a research octane number of
91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand
or premium unleaded fuel. Use of unleaded fuel will extend spark plug life
and reduce maintenance costs.
3-6
EAU13560
Fuel cock
The fuel cock supplies fuel from the
tank to the carburetor while filtering it also.
The fuel cock has three positions:
OFF
1. Arrow mark positioned over “OFF”
With the lever in this position, fuel will
not flow. Always return the lever to this
position when the engine is not running.
INSTRUMENT AND CONTROL FUNCTIONS
1
(a)
(b)
ON
RES
OFF
FUEL
ON
ON
1. Arrow mark positioned over “ON”
1
With the lever in this position, fuel flows
to the carburetor. Normal riding is done
with the lever in this position.
RES
RES
RES
OFF
ON
FUEL
1
fuel while riding, move the lever to this
position. Fill the tank at the first opportunity. Be sure to set the lever back to
“ON” after refueling!
EAU13600
Starter (choke) knob “”
1. Starter (choke) knob “”
Starting a cold engine requires a richer
air-fuel mixture, which is supplied by
the starter (choke).
Move the knob in direction (a) to turn on
the starter (choke).
Move the knob in direction (b) to turn off
the starter (choke).
2
3
4
5
6
7
8
9
1. Arrow mark positioned over “RES”
This indicates reserve. If you run out of
3-7
INSTRUMENT AND CONTROL FUNCTIONS
1
2
Kickstarter
1
2
3
4
5
6
7
8
9
1
1. Kickstarter
If the engine fails to start by pushing the
start switch, try to start it by using the
kickstarter. To start the engine, fold out
the kickstarter lever, move it down lightly with your foot until the gears engage,
and then push it down smoothly but
forcefully. This model is equipped with
a primary kickstarter, allowing the engine to be started in any gear if the
clutch is disengaged. However, shifting
the transmission into the neutral position before starting is recommended.
EAU13660
Seat
To remove the seat
1. Remove the bolts, and then pull
the seat off.
1(×2)
1. Bolt
To install the seat
1. Insert the projection on the front of
the seat into the seat holder as
shown.
EAU13970
1. Projection
2. Seat holder
2. Place the seat in the original position, and then tighten the bolts.
NOTE:
Make sure that the seat is properly secured before riding.
3-8
INSTRUMENT AND CONTROL FUNCTIONS
1
EAU14281
Helmet holder
1
1. Helmet holder
To open the helmet holder, insert the
key into the lock, and then turn the key
as shown.
To lock the helmet holder, place it in the
original position, and then remove the
key.
WARNING
Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of control and possibly an accident.
EWA10160
EAU15090
Shock absorber
EWA10220
WARNING
This shock absorber contains highly
pressurized nitrogen gas. For proper handling, read and understand
the following information before
handling the shock absorber. The
manufacturer cannot be held responsible for property damage or
personal injury that may result from
improper handling.
Do not tamper with or attempt to
●
open the gas cylinder.
Do not subject the shock ab-
●
sorber to an open flame or other
high heat sources, otherwise it
may explode due to excessive
gas pressure.
Do not deform or damage the
●
gas cylinder in any way, as this
will result in poor damping performance.
●
Always have a Yamaha dealer
service the shock absorber.
Carrier
1. Carrier
WARNING
Do not exceed the load limit of
●
3 kg (7 lb) for the carrier.
Do not exceed the maximum
●
load of 180 kg (397 lb) for the
vehicle.
EAU15110
2
3
4
EWA10170
5
6
7
8
9
3-9
INSTRUMENT AND CONTROL FUNCTIONS
Luggage strap holders
1(×2)
1
2
3
4
1. Luggage strap holder
There are four luggage strap holders
5
below the carrier.
6
7
8
9
1(×2)
EAU15170
EAU15300
Sidestand
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)
EWA10240
WARNING
The vehicle must not be ridden with
the sidestand down, or if the sidestand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the responsibility of raising the sidestand before starting off. Therefore, check
this system regularly as described
below and have a Yamaha dealer repair it if it does not function properly.
3-10
Loading...