Yamaha RXZ-1 Brochure

RX-Z1

AV Receiver

VOLUME

INPUT SELECTOR

INPUT MODE

STANDBY

/ON

6CH

SPEAKERS A B

BASS

STEREO

FM/AM

PROGRAM

INPUT

EFFECT

TREBLE

PROCESSOR

DIRECT

SILENT

PHONES

S VIDEO VIDEO

EXTENSION

OFF

PRESET

TUNING

PRESET

MEMORY

/TUNING

MODE

/TUNING

A/B/C/D/E

EDIT

MAN'L/AUTO FM

AUTO/MAN'L MONO

SOURCE/REMOTE

BALANCE

DVD

D–TV/LD CABLE

MD/TAPE

CD–R

SAT

TUNER

VCR 1

VCR 2

VCR 3/DVR

PHONO

VIDEO AUX

REC OUT/ZONE 2

OPTICAL

BASS

VIDEO AUX

L AUDIO

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions should

be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water – for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet

are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

CAUTION I

11 Power Sources – This product should be operated only from the

type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

15 Power Lines – An outside antenna system should not be located

in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16 Overloading – Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind into

this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

18 Servicing – Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19 Damage Requiring Service – Unplug this product from the wall

outlet and refer servicing to qualified service personnel under the following conditions:

a) When the power-supply cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,

e) If the product has been dropped or damaged in any way,

and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

IMPORTANT SAFETY INSTRUCTIONS

22 Wall or Ceiling Mounting – The unit should be mounted to a

wall or ceiling only as recommended by the manufacturer.

23 Heat – The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or cable

system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FCC INFORMATION (for US customers only)

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810–20)

GROUNDING CONDUCTORS (NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

CAUTION II

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place with at

least 30 cm on the top, 10 cm on the right and left, and 10 cm at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage and/or discolora-

tion on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the power cord

from the wall outlet during an electrical storm.

14 Take care of this unit so that no foreign objects and/or liquid

drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact qualified

YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

16 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set this unit in

the standby mode, and disconnect the AC power plug from the wall outlet.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-

003.

IMPORTANT

Please record the serial number of this unit in the space below. Model: Serial No.: The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.

For RAV-2000Z1

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 To avoid failure, do not spill liquid on the remote control.

3 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that the remote control is faulty.

FOR CANADIAN CUSTOMERS

This Class B digital apparatus complies with Canadian ICES-

003.

IMPORTANT

Please record the serial number of this unit in the space below. Model: Serial No.: The serial number is located inside the battery compartment. Retain this Owner’s Manual in a safe place for future reference.

CAUTION III

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corp.,

Address: 6660 Orangethorpe Ave.

Buena Park, CA90620

Telephone: 714-522-9105

Type of Equipment: Remote Control

Model Name: RAV-2000Z1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A)

CAUTION

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

2. IMPORTANT: When connecting this product to

3. NOTE: This product has been tested and found to comply

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

CAUTION IV

Contents

INTRODUCTION

PREPARATIONS

BASIC OPERATIONS

INTRODUCTION 3

Features ......................................................................................................................... 4

Controls and functions .................................................................................................. 6

PREPARATIONS 13

Speaker system configurations ................................................................................... 14

Speaker placement ...................................................................................................... 16

Connections ................................................................................................................ 18

On-screen displays (OSD) .......................................................................................... 33

Speaker mode settings ................................................................................................ 34

Speaker output levels .................................................................................................. 38

BASIC OPERATIONS 41

Basic playback ............................................................................................................ 42

Basic recording ........................................................................................................... 50

ADVANCED OPERATION 51

Set menu items ............................................................................................................ 52

Remote control features .............................................................................................. 64

Adjusting the levels of the effect speakers.................................................................. 81

Sleep timer .................................................................................................................. 82

Zone 2 ......................................................................................................................... 83

SOUND FIELD PROGRAMS 85

Digital sound field processing (DSP) ......................................................................... 86

Hi-Fi DSP-sound field program .................................................................................. 88

CINEMA-DSP sound field program ........................................................................... 90

Sound field program parameter editing ...................................................................... 95

Digital sound field parameter descriptions ................................................................. 96

OPERATION

ADVANCED

SOUND FIELD

PROGRAMS

APPENDIX

APPENDIX 101

Troubleshooting ........................................................................................................ 102

CINEMA EQ frequency characteristics.................................................................... 105

Reference chart for the input and output jacks ......................................................... 106

Specifications ............................................................................................................ 107

English

E-1

CHECKING THE PACKAGE CONTENTS

Check your package to make sure it has the following items.

RAV-2000Z1

Intelligent remote control

Computer interface cable

(RS-232C)

Batteries (4) (LR6) Power cord

AM loop antenna Indoor FM antenna

E-2

INTRODUCTION

Introduction

This section describes the features of the RX-Z1, and its controls and functions.

FEATURES ........................................................................................................... 4

CONTROLS AND FUNCTIONS............................................................................ 6

Front panel .................................................................................................................... 6

Remote control .............................................................................................................. 8

Front panel display ...................................................................................................... 11

Rear panel ................................................................................................................... 12

E-3

English

FEATURES

■ Built-in 8-channel power amplifier

• Main: 130 W + 130 W (8Ω) RMS Output Power, 0.015% THD, 20 – 20,000 Hz

• Center: 130 W (8Ω) RMS Output Power, 0.015% THD, 20 – 20,000 Hz

• Rear: 130 W + 130 W (8Ω) RMS Output Power, 0.015% THD, 20 – 20,000 Hz

• Front: 45 W + 45 W (8Ω) RMS Output Power, 0.05% THD, 1 kHz

• Rear center: 130 W (8Ω) RMS Output Power, 0.015% THD, 20 – 20,000 Hz

■ Digital Sound Fields (DSP)

Technological advances in sound reproduction over the last 30 years have enhanced the listening experience with improved clarity, precision, and power. However, something has been missing: the atmosphere and acoustic ambience of the public venue. Our Yamaha engineers have extensively researched the nature of sound acoustics and the way sound reflects inside a room. We sent these engineers to famous theaters and concert halls around the world to measure the acoustics of those venues with sophisticated microphones. The data they collected is used to recreate these environments in digital sound fields. Some of these digital sound fields have been created using data measured at the original venue; others have been created from combinations of data to form unique environments for specific purposes. Some have been designed especially for music, and others especially for movies. Of course, this only solves half of the problem. Because these engineers have no way of knowing the acoustics of your entertainment room, we have made it possible for you to adjust the various parameters of this data to tailor each virtual venue to your taste. You can use these sound fields to enhance any source and in combination with any of the following surround sound technologies.

■ CINEMA-DSP: Dolby Digital + DSP and DTS + DSP

The Dolby Digital system and DTS system show their full capability in large movie theaters, because feature film soundtracks are designed to be reproduced in such environments. It is difficult to recreate a sound environment similar to a movie theater in your entertainment room because of the room size, wall materials, and the number of speakers in your entertainment system. Yamaha DSP technology makes it possible for you to enjoy nearly the same sound experience as that of a large movie theater in your entertainment room by compensating for lack of presence and dynamics in your entertainment room with Yamaha's original digital sound fields combined with Dolby Digital or DTS soundtracks.H

■ Virtual CINEMA DSP and SILENT CINEMA DSP

Yamaha developed the Virtual CINEMA DSP algorithm which allows you to experience the virtual sound fields without surround speakers. This makes it possible for the RX-Z1 to produce a full surround sound catering to the number of speakers you have. The RX-Z1 also has a SILENT CINEMA DSP algorithm which is achieved by the crosstalk processing applying the precise Head Related Transfer Function. Yo u can therefore enjoy listening to the CINEMA DSP soundfields on headphones.

■ Various decoders to support the newest sound effect technology

This unit is equipped with the following signal format decoders.

• Dolby Digital and Dolby Digital EX

The Matrix decoder enables 6.1-channel playback of the 5.1-channel sources by extracting the rear center channel signals from the rear L/R channel signals.

• DOLBY PRO LOGIC

DOLBY PRO LOGIC is the improved technique to decode vast numbers of existing Dolby Surround programs. This new technology enables a discrete 5-channel playback with two left and right main channels, a center channel, and two left and right rear channels compared with one limited rear channel for the conventional Pro Logic technology. Also the music mode is available for 2-channel sources in addition to the movie mode.

• DTS and DTS ES

The RX-Z1 is also equipped with a DTS decoder, which uses a 5.1-channel system to create a full surround sound environment. It was developed as a way to replace the analog soundtracks of movies with six channels of digital sound. In comparison with Dolby Digital, DTS uses less compression to store the sound information. The newly presented DTS ES system reproduces digital sound similar to Dolby Digital EX. The use of the rear center speaker along with the existing 5.1-channel speakers provides a fully immersive cinematic audio experience.

• DTS Neo: 6

Neo: 6 decodes the conventional 2-channel sources for 6-channel playback by the specific decoder. It enables playback with the full-range channels with higher separation just like digital discrete signal playback. Two modes are available; “Music mode” for playing music sources and “Cinema mode” for movies.

• DTS 96/24

DTS 96/24 achieves the high quality playback with all 5.1 channels at the sampling frequency 96 kHz/24 bit.

E-4

FEATURES

■ Various input and output jacks

The RX-Z1 has various output jacks for audio and video signals as well as a digital recording output jack. Many input jacks are also available for connection to multiple audio-video sources. All the video inputs and outputs have S-video jacks in addition to standard composite video jacks for improved video picture quality. Component video input and output jacks are also available to deliver the excellent video signals from DVD players and other high quality video sources. The coaxial and optical digital signal jacks (provided for direct transmission of digital signals) automatically detect Dolby Digital, DTS, and PCM signals. A demodulator circuit is built into the Dolby Digital RF input so you can connect it directly to the Dolby Digital RF signal output on your LD player. Additionally, there are six audio inputs for discrete multichannel reproduction from an external decoder. The RX-Z1 also comes with a monaural subwoofer jack and split subwoofer jacks which can reproduce delicate but powerful low frequency effects.

■ Intelligent remote control

The intelligent remote control can be used with most components that understand infrared (IR) remote control signals. Its easy-to-use touch screen and its intuitive interface make it the perfect remote control for every user. The remote control (RC) is completely customizable. In the memory of the remote control, RC codes are stored to activate different brands of all kinds of video and audio components. The remote control is set up by default to operate with YAMAHA components. If you have other brands, you simply define the brands of your components when you use the remote control for the first time. The remote control can also learn RC codes from existing remote controls. It is designed to add components and functions, relabel buttons, record macros and set timers. With the RAVedit software you create your own control panels and define your personal look.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.

INTRODUCTION

“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are trademarks of Digital Theater System, Inc.

E-5

English

Front panel

123 4567890qwertyui o

STANDBY

CONTROLS AND FUNCTIONS

VOLUME

INPUT SELECTOR

INPUT MODE

/ON

6CH

SPEAKERS A B

INPUT

BASS

SILENT

PHONES

PROGRAM

TREBLE

STEREO

S VIDEO VIDEO

pas d f

1 STANDBY/ON

Turns this unit on (On mode) and off (Standby mode). When you turn on this unit, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound. In Standby mode, this unit consumes a small amount of power so it can respond to the remote control.

2 INPUT MODE

Selects the mode of input for sources that output two or more types of signals to this unit (see page __).

Caution

• You cannot control the input mode when you select 6CH INPUT

as the input source.

3 INPUT SELECTOR

Selects the input source (D-TV/LD, CABLE, SAT, VCR 1, VCR 2, VCR3/DVR, V-AU X, DVD, MD/TAPE, CD-R, TUNER, CD, PHONO) you want to listen to or watch (see page __).

4 Remote control sensor

Receives signals from the remote control.

5 SPEAKERS A/B

When pushed in (ON), these buttons turn on the set of main speakers connected to the A and/or B terminals on the rear panel.

6 Front panel display

Shows information about the operational status of this unit (see page __).

7 6CH INPUT

Switches between 6CH INPUT mode and normal input modes. 6CH INPUT mode takes priority over the source selected with INPUT SELECTOR. You cannot use DSP sound field programs while using an external decoder.

PRESET

/TUNING

EDIT

SOURCE/REMOTE

D–TV/LD

CABLE

SAT

VCR 1

VCR 2

VIDEO AUX

REC OUT/ZONE 2

MEMORY

MAN'L/AUTO FM

TUNING MODE

AUTO/MAN'L MONO

DVD

MD/TAPE

CD–R

TUNER

PHONO

EFFECT

PROCESSOR

DIRECT

FM/AM

A/B/C/D/E

BASS

EXTENSION

OFF

VIDEO AUX

L AUDIO

PRESET

/TUNING

BALANCE

OPTICAL

VCR 3/DVR

8 PROGRAM q/w

Selects the sound field program (see page __). Selecting a sound field program turns on the effect.

9 PROCESSOR DIRECT ON/OFF

When pushed in (ON), BASS, TREBLE, BALANCE, and BASS EXTENSION are bypassed, eliminating any alteration of the

original signal.

0 STEREO/EFFECT

Switches the effect speakers (center, front effect, rear and rear center) on and off. If you turn off the output of these speakers using STEREO/EFFECT, all DTS and Dolby Digital audio signals are directed to the main left and right channels except for the LFE channel.

Cautions

• When DTS or Dolby Digital signals are mixed, the left and right main channel signal levels may not match.

• If “1B MAIN SP” on the SET MENU is set to “SMALL” and “1E LFE/BASS OUT” is set to “SW”, or “1E LFE/BASS OUT” is set to “BOTH”, the LFE signals will be output from the subwoofer.

q FM/AM

Switches the reception band between FM and AM.

w A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

e BASS EXTENSION ON/OFF

When pushed in (ON), this feature boosts the bass frequency of the left and right main channels by +6 dB (60 Hz) while maintaining overall tonal balance. This boost is useful if you do not use a subwoofer. However, this boost may not be noticeable if the main speakers are set to “SMALL” and the bass output mode is set to “SW.”

E-6

CONTROLS AND FUNCTIONS

r PRESET/TUNING q/w

Selects preset station number 1 to 8 when the colon (:) appears on the left of the band indication (“FM” or “AM”) on the front panel display, and selects the tuning frequency when the colon (:) does not appear.

t BALANCE

Controls the balance of the sound levels coming from the left and right main speaker(s). Setting this control to the center position is appropriate for most situations.

y PRESET/TUNING EDIT

Switches the function of PRESET/TUNING q/w (the colon (:) turns on or off) between selecting a preset station number and tuning. This button is also used to exchange the assignment of two preset stations with each other.

u MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for more than 3 seconds to start automatic presetting stations.

i TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual. To select the automatic tuning mode, press this button so that the “AUTO” indicator lights up on the front panel display. To select the manual tuning mode, press this button so that the “AUTO” indicator does not light up.

d VIDEO AUX

Inputs audio and video signals from a portable external source such as a video camera.

f REC OUT/ZONE 2

Selects the source you want to direct to the audio/video recorder and ZONE 2 outputs independent of the source you are listening to in the main room. When set to the SOURCE/REMOTE position, the input source is directed to all outputs.

■ Opening and closing the front panel door

When you are not operating the controls behind the front panel door, close the door.

A T

O U

E C

E I V

E R

R X

–

INTRODUCTION

o VOLUME

Controls the output level of all audio channels. This does not affect the REC OUT level.

p BASS

Adjusts the low frequency response for the left and right main speaker channels. Turn the control to the right to increase the low frequency response and turn the control to the left to decrease the low frequency response.

Caution

• If you increase or decrease the low frequency sound to an extreme level, the tonal quality from the center, front effect, rear center, and rear speakers may not match that of the left and right main speakers.

a PHONES

Outputs audio signals for private listening using headphones.

Cautions

• When you connect headphones, no signals are output to the

PREOUT jacks or the speakers.

• When the signal input into the 6CH INPUT jack is being played back, only the left and right channel signals are output through the headphones.

s TREBLE

Adjusts the high frequency response for the left and right main channels. Turn the control to the right to increase the high frequency response and turn the control to the left to decrease the high frequency response.

Caution

• If you increase or decrease the high frequency sound to an extreme level, the tonal quality from the center, front effect, rear center, and rear speakers may not match that of the left and right main speakers.

English

E-7

CONTROLS AND FUNCTIONS

Remote control

2 3

1 Sending eye

Outputs infrared (IR) remote control signals. Aim this at the component you want to operate.

2 CONTRAST +/–

Adjust the contrast of the display.

3 BACKLIGHT

Turns the backlight on.

4 Direct-access buttons

• POWER: Turns on the power of this unit.

• STANDBY: Sets this unit in the standby mode.

• MUTE: Mutes the sound. While the mute function is on,

“MUTE ON” appears on the front panel display.

• VOL +/–: Increases or decreases the volume level.

5 Touch screen

6 Left/right buttons

Depending on the components the remote control is operating, these buttons change function. The current function is displayed on the touch screen right above the button.

7 Learning eye

Receives RC codes from existing remote controls.

8 I/O (Serial port)

See page __ for information.

■ Display on the touch screen

9 Battery door

0 RESET

See page __ for information.

1 Home

To go to the Home menu.

2 Remote control icon

Touch and hold to enter Setup.

3 Device menu

To open control panel of components.

4 Panel number

Shows active control panel.

5 Mode menu

To customize the remote control.

6 Control panel

To send commands to components.

7 Scroll buttons

To display previous/next control panel.

E-8

8 Macro menu

To open stored list of commands.

CONTROLS AND FUNCTIONS

■ Installing batteries in the remote control

Slide the battery door off the back of the remote

control.

Insert 4 supplied batteries as indicated on the bottom

of the battery compartment.

Slide the battery door back on.

After a few seconds, the remote control set up automatically and beeps twice to indicate that it is ready to use.

Cautions

• Insert the batteries in the correct direction by aligning the + and – marks on the batteries with the polarity illustrations (+ and –) inside the battery compartment.

• Change the batteries periodically.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.

• Do not use rechargeable batteries.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.

■ About changing batteries

When batteries are running low, the low battery icon flashes at the center top of the display. Replace the batteries as soon as possible to ensure perfect performance.

Note

• The remote control retains all settings when the batteries have discharged or when you remove and replace them. You will need only to reset the clock.

■ Using the remote control

The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.

INPUT SELECTOR

INPUT MODE

STANDBY

/ON

30° 30°

Remote control

Cautions

• When the sensor is covered or there is a large object between the remote control and the main unit, the sensor cannot receive signals.

• The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a fluorescent or strobe light). In this case, change the direction of the light or reposition the main unit to avoid direct lighting.

• Handle the remote control with care.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types of

conditions:

1 high humidity or temperature such as near a heater, stove or

bath

2 dusty places 3 in places subject to extremely low temperatures

VOLUME

Approximately 10 m (33 feet)

INTRODUCTION

E-9

English

CONTROLS AND FUNCTIONS

■ Turning on the display

Tap the screen gently with your finger or a blunt, soft object like a pencil eraser.

The display is activated and the Home menu appears.

Tap the screen gently.

■ Using the backlight

Press BACKLIGHT on the left side of the remote control.

The backlight shuts off after a few seconds to save power.

Note

• In the settings, you can choose to activate the backlight automatically when you turn on the remote control (see page __).

■ Activating modes

The remote control has different modes. When controlling components, the remote control should be set to Use mode. If a label (like or ) appears at the center top of the touch screen, see page __ for information or switching your remote control to the Use mode.

■ Using touch screen buttons

1. Sending commands

By tapping the touch screen buttons you send commands to the components you have selected. When you send a command, the remote control icon indicates that it is transmitting signals name of the active components is indicated on the device tab.

2. Scrolling

Most components have more than one control panel. You can scroll through these control panels using on the left (or right) bottom of the screen indicates the active panel number and the total number of panels, for example . By holding down a scroll button, you cycle repeatedly through all the control panels of a component.

and . The panel number

. The

The Home menu appears.

Notes

• If the display stays blank or becomes black, adjust the contrast

using CONTRAST +/– on the left side of the remote control.

• If another panel is displayed, tap the Home button.

• The remote control shuts down automatically.

■ Using the left/right buttons

The left/right buttons change function depending on the component the remote control is operating. The current function is displayed on the touch screen right above the button. The function can be an IR command which is transmitted, or a jump to a specific component page.

■ Using the direct-access buttons

You can operate this unit with the direct-access buttons (POWER, STANDBY, MUTE and VOL +/–) at any time, even without turning

on the touch screen.

E-10

CONTROLS AND FUNCTIONS

Front panel display

D–TV/LD DVD

CABLE

SAT VCR 1 TUNER VCR 2 CD

VCR3/DVR

V–AUX

STEREO TUNED MEMORY

7 0q8we rtyui

SLEEP

MD/TAPE CD–R

PHONO

AUTO

1 Input source indicator

Shows the current input source with the arrow-shaped cursor.

2 DSP indicator

Lights up when you select a digital sound field program.

96kHz/24bit

indicator

Lights up when the DTS 96/24 signal is input to this unit.

4 Processor indicators

When any function of DTS, MATRIX, DISCRETE, g, and

PRO LOGIC

is activated, its indicator lights up.

342

MATRIX DISCRETE

DIGITAL

PRO LOGIC

96kHz/24bit

DSP

PCM

VIRTUAL

VOLUME

LFE

L C R

RC RR

SILENT

q AUTO indicator

Shows that this unit is in the automatic tuning mode.

w VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see page __).

e PCM indicator

Lights up when this unit is reproducing PCM (Pulse Code Modulation) digital audio signals.

r Headphones indicator

Lights up when headphones are connected.

INTRODUCTION

5 Multi-information display

Shows the current DSP program and other information when adjusting or changing settings.

6 VOLUME level indicator

Indicates the volume level.

7 STEREO indicator

Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the “AUTO ” indicator is lit.

8 TUNED indicator

Lights up when this unit tunes in to a station.

9 SLEEP indicator

Lights up while the sleep timer is on.

0 MEMORY indicator

Flashes to show a station can be stored.

t SPEAKERS A/B indicator

Lights up according to which set of main speakers are selected. Both indicators light up when both sets of speakers are selected.

y SILENT indicator

Lights up when headphones are connected with the sound effect (see “SILENT CINEMA DSP” on page __).

u Input channel indicator

Indicates the channel components of input signals being received.

i LFE indicator

Lights up when the input signal contains the LFE signal.

E-11

English

CONTROLS AND FUNCTIONS

Rear panel

12 3 45 67

RF (AC–3)

COAXIAL IN

OPTICAL OUT

OPTICAL IN

GND

DVD

CABLE

(PLAY)

CD–R

OUT

(REC)

MD/

TAPE

(PLAY)

MD/TAPE

OUT

(REC)

CD–R

MAIN

DVD

SURROUND

SUB

D–TV

WOOFER

/LD

6CH INPUT

SAT

VCR 3 /DVR

CENTER

ZONE 2 OUTDIGITAL

VIDEO

LRR L

MONITOR

DVD

D–TV

/LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

VCR 3 /DVR

OUT

AUDIOAUDIODIGITAL

PHONO

89 qw e0

1 DIGITAL OPTICAL/COAXIAL jacks

See page __ for detailed information.

VIDEO

S VIDEO

COMPONENT VIDEO

YPB/C

PREOUT/MAIN IN

CONTROL

REMOTE 1

OUT

REMOTE 2

RS–

232C

CTRL OUT

10mA

+12V

MAX.

R L

MONO

REAR CTR

R L

PR/C

DVD

D–TV /LD

SAT

MONITOR

OUT

FRONT

OUT

REAR

(

SURROUND

SUB

WOOFER

SPLIT

CENTER

OUT

MAIN

OUT

)

TUNER

–GND

FM ANT

UNBAL.

R L

CAUTION

ATTENTION

75Ω

SPEAKERS

R L

FRONT

AM ANT

REAR

(

SURROUND

)

CENTER

REAR CENTER

R L

MAIN

SEE INSTRUCTION MANUAL FOR CORRECT SETTING. POUR UN REGLAGE CORRECT, SE REPORTER AU MANUEL D’INSTRUCTIONS.

8 6CH INPUT jacks

See page __ for connection information.

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SELECTEUR D’IMPEDANCE

FRONT

: 6ΩMIN. /SPEAKER

4Ω

MIN. /SPEAKER

REAR

4Ω

MIN. /SPEAKER

REAR CENTER

4Ω

MIN. /SPEAKER

CENTER

4Ω

MIN. /SPEAKER

MAIN A OR B

8Ω

MIN. /SPEAKER

A + B

AC OUTLETS

FRONT REAR REAR CENTER CENTER MAIN A OR B A + B

: 8ΩMIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

16Ω

MIN. /SPEAKER

SWITCHED

1.0A MAX. TOTAL 120V 60Hz

100W MAX. TOTAL

AC IN

2 Audio component jacks

See pages __ and __ for connection information.

3 Video component jacks

See pages __ and __ for connection information.

4 Antenna input terminals

See page __ for connection information.

5 Speaker terminals

See pages __ and __ for connection information.

6 AC IN

Use this inlet to plug in the supplied power cord.

7 IMPEDANCE SELECTOR

Use this switch to match the amplifier output to your speaker impedance. Turn off the power before you change the setting of this switch (see page __).

9 ZONE 2 OUT jacks

See page __ for connection information.

0 REMOTE 1 IN/OUT/REMOTE 2 IN jacks

See page __ for connection information.

q RS-232C/CTRL OUT +12V terminals

These are control expansion terminals for commercial use. Consult your dealer for details.

w PREOUT/MAIN IN jacks

See page __ for connection information.

e AC OUTLETS

Use these outlets to supply power to your other audio/video component.

E-12

Preparations

This section explains how to make preparations (speaker selection and placement, subwoofer usage, connection with other components, speaker mode setting, and speaker level adjustment) to fully use the RX-Z1.

PREPARATIONS

SPEAKER SYSTEM CONFIGURATIONS .......................................................... 14

SPEAKER PLACEMENT .................................................................................... 16

CONNECTIONS .................................................................................................. 18

Before connecting components ................................................................................... 18

Connecting digital jacks .............................................................................................. 19

Connecting audio components .................................................................................... 19

Connecting video components .................................................................................... 21

Connecting speakers ................................................................................................... 29

Connecting other components .................................................................................... 31

Connecting the power supply cords ............................................................................ 32

ON-SCREEN DISPLAYS (OSD) ......................................................................... 33

OSD modes ................................................................................................................. 33

Selecting the OSD mode ............................................................................................. 33

SPEAKER MODE SETTINGS ............................................................................ 34

SPEAKER OUTPUT LEVELS ............................................................................ 38

TEST DOLBY SUR. .................................................................................................. 39

TEST DSP ................................................................................................................... 40

English

E-13

SPEAKER SYSTEM CONFIGURATIONS

The most complete speaker configuration consists of eight speakers: the left and right main speakers, a center speaker, the left and right rear speakers, the left and right front effect speakers, and a rear center speaker. If you do not use eight speakers, you can direct the signals for speakers that are not in your system to other speakers in your configuration. A subwoofer can be used with any of these configurations to produce a fuller sound.

Front effect speaker (FL)

TV (monitor)

1.5 – 1.8 m (5 – 6 feet)

Center speaker (C)

Main speaker (L)

Front effect speaker (FR)

Main speaker (R)

Rear effect speaker (RR)

Rear center speaker (RC)

Rear effect speaker (RL)

■ 8-speaker configuration –full CINEMA-DSP–

When you reproduce feature film software, this configuration fully expresses the powerful and realistic sound qualities of 70 mm multitrack audio. The dialogue is positioned as if it were coming from directly on the screen, the sound effect is positioned slightly behind the screen, and the soundtrack music is positioned even further behind the screen to express the width and depth of the overall presentation. This configuration makes the most of this unit's capability.

Speakers to be used

• Main L/R

• Center

• Rear L/R

• Front effect L/R

• Rear center

■ 6-speaker configuration –Hi-Fi DSP–

This configuration is used the most for audio playback with Hi-Fi DSP. It does not position the dialogue sound as well as a 7- or 8-speaker configuration. However, it creates a dynamic DSP (Digital Sound Field Processor) sound field which adds depth to the sound. For this speaker configuration, change SET MENU item “1A CENTER SP” to “NONE” and “1D REAR CT SP” to “NONE”.

(L+C) (R+C)

Speakers to be used

• Main L/R

• Rear L/R

• Front effect L/R

E-14

SPEAKER SYSTEM CONFIGURATIONS

■ 5-speaker configuration –standard 5.1 channel–

This configuration does not express the height of the sound field as well as the 7- or 8-speaker configuration. However, it positions the dialogue sound as coming directly from the screen. For this speaker configuration, change SET MENU item “1F FRONT EFCT SP” to “NONE” and “1D REAR CT SP” to “NONE”.

Speakers to be used

(L+FL) (R+FR)

• Main L/R

• Center

• Rear L/R

■ 4-speaker configuration –minimum requirement–

In this configuration, the center speaker signals and front effect speaker signals are directed to the left and right main speakers. For this speaker configuration, change SET MENU item “1A CENTER SP” to “NONE”, item “1F FRONT EFCT SP” to “NONE”, and item “1D REAR CT SP” to “NONE”.

(L+C+FL) (R+C+FR)

Speakers to be used

• Main L/R

• Rear L/R

■ Speaker configurations and speaker mode

Select the appropriate speaker mode depending on the speaker configuration. See “SPEAKER MODE SETTINGS” on page __ for details.

1A CENTER SP (Center)

1B MAIN SP (Main L/R)

1C REAR L/R SP (Rear L/R)

1D REAR CT SP (Rear center)

1F FRONT EFCT SP (Front effect L/R)

8 speakers

LRG/SML

LARGE/SMALL

LRG/SML

YES

7 speakers

LRG/SML

LARGE/SMALL

LRG/SML

NONE

YES

6 speakers

NONE

LARGE/SMALL

LRG/SML

NONE

YES

5 speakers

LRG/SML

LARGE/SMALL

LRG/SML

NONE

4 speakers

NONE

LARGE/SMALL

LRG/SML

NONE

PREPARATIONS

Note

• As a guideline, select “LARGE” for the larger speaker diameter than 16 cm, and “SMALL” for the smaller speaker diameter than 15 cm. Change the speaker mode setting as listening to the actual playback sound if it does not meet your expectation.

E-15

English

SPEAKER PLACEMENT

Refer to the following diagram when you place the speakers.

Caution

• Use magnetically shielded speakers. If this type of speakers still creates the interference with a monitor, place the speakers away from the monitor.

■ Placing the main speakers

Place the left and right main speakers an equal distance from the main listening position.

TV or video

Main

speaker

monitor

Main

speaker

■ Placing the center speaker

TV or video

monitor

Center speaker

■ Placing the front effect, rear and rear center speakers

1m 0.5 - 1m 1.5 - 3m 0.5 - 1m 1m

(3ft) (1 - 3ft) (5 - 15ft) (1 - 3ft) (3ft)

If you have a TV or video monitor in your system, the distance of each speaker from each side of the TV or video monitor should be the same.

If you have a TV or video monitor in your system, align the front face of the center speaker with the front face of the monitor. Place the speaker as close to the monitor as possible, such as directly over or under the monitor. If you place the speaker under the monitor, the front effect speakers can adjust the height of the sound to correspond with the action on the screen (depending on the listener’s position). If you have a projection screen in your system, place the center speaker under the screen. Be sure to align the speaker with the center of the screen.

These speakers should be placed about 0.5 – 1 m (1 – 3 feet) outside the main speakers and in the front of the room. They should be turned toward the main listening position. Place the rear speakers in the back of the room so they face the main listening position. The rear speakers can be placed farther apart than the front effect speakers. Place these speakers at the height of 1.5 m when listening as sitting on the floor or 1.8 m when listening as sitting on the chair. Once you begin listening to programs, continue to adjust the speaker placement until you obtain a balanced sound from the main speakers and the front effect and rear speakers.

This distance can be farther than the front effect speakers’.

■ When you use a projection screen

Screen

1/4

Place the speakers as shown in the illustration. The main speakers should be placed about one-quarter of the way up from the bottom of the screen. Place the center speaker in the center and directly under the screen. The center speaker provides precise dialogue localization. When you use a projection screen with your system, the front effect speakers provide better effect quality. The CINEMA-DSP sound field programs (see pages __ to __) raise the sound from the center speaker upward and provide natural sound corresponding with the video images.

E-16

SPEAKER PLACEMENT

■ Placing the subwoofers

Place the front subwoofer near the main speakers. Turn it slightly toward the center of the room to reduce wall reflections. If you use a rear subwoofer, place it behind the main listening position. The placement of the rear subwoofer is not critical because of the ultra low frequencies of the sound being reproduced. By adding a high quality subwoofer to the speaker configurations shown on page __, you can enjoy more powerful and realistic movie effects, even if your main speakers are large.

Front subwoofer

Rear subwoofer

PREPARATIONS

Note

• If you use different brands of speakers (with different tonal qualities) in your configuration, the tone of a moving human voice and other types of sound may not shift smoothly. We recommend that you use speakers from the same manufacturer or speakers with the same tonal quality. You can also adjust the output levels and equalization of your effect speakers using the SET MENU (see pages __ and __). If you are using small speakers, the addition of a subwoofer will reinforce the sound effects of movies.

E-17

English

CONNECTIONS

Before connecting components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been completed.

• Some components require different connection methods and have different jack names. Refer to the operation instructions for each component also.

• Input and output jacks for the pin jacks are color-coded depending on the signal type.

• When connecting input and output jacks, use commercially available cables (pin-plug cable, fiber-optic cable, coaxial cable and S-Video

cable).

• When this unit interferes with the other components, replace this unit apart from those components. To prevent the interference with other components, it is recommended that an external antenna is placed and coaxial cables are used for connections.

Connecting audio components ^ P.__

PHONO

CABLE

CD–R

MD/ TAPE

CD–R

D–TV

VCR 3

/DVR

GND

DVD

(PLAY)

CD–R

OUT

(REC)

(PLAY)

MD/TAPE

OUT

(REC)

MAIN

DVD

SURROUND

SUB

WOOFER

/LD

6CH INPUT

SAT

(AC–3)

COAXIAL IN

OPTICAL OUT

OPTICAL IN

CENTER

Connecting video components ^ P.__

AUDIOAUDIODIGITAL

VIDEO

ZONE 2 OUTDIGITAL

LRR L

CABLE

VCR 1

VCR 2

VCR 3 /DVR

MONITOR

VIDEO

S VIDEO

DVD

D–TV

/LD

SAT

OUT

COMPONENT VIDEO

YPB/C

PREOUT/MAIN IN

CONTROL

REMOTE 1

OUT

REMOTE 2

RS–

232C

CTRL

OUT

10mA

+12V

MAX.

R L

MONO

REAR CTR

R L

Connecting the antennas ^ P.__

D–TV

REAR

TUNER

DVD

/LD

SAT

OUT

)

SUB

SPLIT

OUT

MAIN

OUT

AM ANT

–GND

FM ANT

75Ω

UNBAL.

R L

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

ATTENTION

POUR UN REGLAGE CORRECT, SE REPORTER AU MANUEL D’INSTRUCTIONS.

PR/C

MONITOR

FRONT

(

SURROUND

WOOFER

CENTER

MAIN

SPEAKERS

R L

CENTER

R L

FRONT

REAR

(

SURROUND

)

REAR CENTER

Connecting the power supply cords ^ P.__

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SELECTEUR D’IMPEDANCE

FRONT

: 6ΩMIN. /SPEAKER

4Ω

MIN. /SPEAKER

REAR

4Ω

MIN. /SPEAKER

REAR CENTER

CENTER MAIN A OR B A + B

4Ω

MIN. /SPEAKER

4Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

FRONT REAR REAR CENTER CENTER MAIN A OR B A + B

AC OUTLETS

AC IN

: 8ΩMIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

16Ω

MIN. /SPEAKER

SWITCHED

1.0A MAX. TOTAL 120V 60Hz

100W MAX. TOTAL

Connecting digital jacks ^ P.__

E-18

Connecting other components ^ P.__

Connecting speakers ^ P.__

CONNECTIONS

Connecting digital jacks

This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables.

Notes

• DIGITAL OUTPUT jacks and analog OUT (REC) jacks are independent. Only digital signals are output from DIGITAL OUTPUT jacks and analog signals from OUT (REC) jacks.

• You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams.

• When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack.

• The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard, this unit

may not function properly.

• You can designate the input for each digital jacks according to your component by using “8 I/O ASSIGNMENT” on the SET MENU (see page __ for details).

Digital input jacks of this unit support the following sampling frequency.

• 32 kHz

• 44.1 kHz: CD, CD-R and MD

• 48 kHz: DVD (48 kHz mode)

• 96 kHz: DVD (96 kHz mode)

• 192 kHz (coaxial input only): DVD audio (2-channel)

Connecting audio components

PREPARATIONS

Before you connect any components, disconnect the power supply to all the components you plan to connect including this unit and determine which jacks are for the left and right channels and for input and output. When you connect other YAMAHA audio component (such as a CD player or changer, MD deck, or tape deck), connect to terminals with the same number labels. Yamaha applies this labelling system to all its products.

■ Connecting a CD recorder

OPTICAL OUT

(AC–3)

COAXIAL IN

OPTICAL OUT

CD recorder

OPTICAL IN

GND

DVD

CABLE

(PLAY)

CD–R

OUT (REC)

MD/

TAPE

(PLAY)

MD/TAPE

OUT (REC)

CD–R

MAIN

DVD

SURROUND

PHONO

ANALOG AUDIO OUT

AUDIOAUDIODIGITAL VIDEO

ANALOG AUDIO IN

LRR L

VIDEO

S VIDEO

DVD

D–TV

/LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

■ Connecting a CD player

The COAXIAL CD and OPTICAL CD jacks are available for a CD player which has coaxial or optical digital outputs.

OPTICAL OUT

(AC–3)

COAXIAL IN

OPTICAL OUT

CABLE

CD–R

MD/ TAPE

CD–R

DVD

CD Player

GND

(PLAY)

CD–R

OUT (REC)

(PLAY)

MD/TAPE

OUT (REC)

MAIN

PHONO

ANALOG AUDIO OUTCOAXIAL OUT

AUDIOAUDIODIGITAL VIDEO

LRR L

VIDEO

S VIDEO

DVD

D–TV /LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

E-19

English

CONNECTIONS

■ Connecting an MD recorder/tape deck

OPTICAL IN

Note

• To connect the OPTICAL (COAXIAL) output jack for an MD recorder with this unit, you can use any of the OPTICAL (COAXIAL) IN jacks by changing the setting for “8 I/O ASSIGN- MENT” on the SET MENU (see page __).

MD recorder/tape deck

ANALOG AUDIO

CABLE

GND

DVD

(PLAY)

CD–R

OUT

(REC)

MD/

TAPE

(PLAY)

MD/TAPE

OUT

(REC)

CD–R

MAIN

(AC–3)

COAXIAL IN

OPTICAL OUT

OUT

PHONO

ANALOG AUDIO IN

AUDIOAUDIODIGITAL VIDEO

LRR L

VIDEO

S VIDEO

DVD

D–TV /LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

■ Connecting a turntable

These jacks are for connecting a turntable with an MM or high output MC cartridge. If you have a turntable with a low output MC cartridge, use an inline boosting transformer or MC-head amplifier when connecting to these jacks.

Turntable

AUDIO OUT

Ground

CABLE

GND

DVD

(AC–3)

COAXIAL IN

PHONO

Caution

• The GND terminal does not electrically ground the turntable. It

simply reduces noise in the signal. In some cases, you may hear less noise if you do not connect to the GND terminal.

AUDIOAUDIODIGITAL VIDEO

LRR L

VIDEO

S VIDEO

DVD

D–TV

/LD

CABLE

SAT

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

(included)

AM loop antenna (included)Indoor FM antenna

TUNER

PR/C

DVD

D–TV

Ground (GND terminal) For maximum safety and minimum

/LD

SAT

MONITOR

OUT

FRONT

OUT

–GND

FM ANT

UNBAL.

AM ANT

75Ω

interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

■ Connecting the indoor FM antenna

Connect the included indoor FM antenna to the FM ANT 75Ω UNBAL. terminal.

■ Connecting the AM loop antenna

Set up the AM loop antenna, then connect it.

Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

Orient the AM loop antenna for the beat reception.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

E-20

CONNECTIONS

Connecting video components

■ About the video jacks

There are three types of video jacks.

12 3

SPEAKERS

R L

FRONT

AM ANT

–GND

FM ANT

75Ω

UNBAL.

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

POUR UN REGLAGE CORRECT, SE REPORTER AU MANUEL D’INSTRUCTIONS.

MAIN

CENTER

REAR

(

SURROUND

REAR CENTER

R L

)

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SELECTEUR D’IMPEDANCE

FRONT

: 6ΩMIN. /SPEAKER

4Ω

MIN. /SPEAKER

REAR

: :

REAR CENTER

4Ω

MIN. /SPEAKER

CENTER

4Ω

MIN. /SPEAKER

MAIN A OR B

4Ω

MIN. /SPEAKER

A + B

8Ω

MIN. /SPEAKER

AC OUTLETS

FRONT REAR REAR CENTER CENTER MAIN A OR B A + B

: 8ΩMIN. /SPEAKER

8Ω

MIN. /SPEAKER

: :

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

8Ω

MIN. /SPEAKER

: :

16Ω

MIN. /SPEAKER

SWITCHED

1.0A MAX. TOTAL 120V 60Hz

100W MAX. TOTAL

AC IN

COAXIAL IN

OPTICAL OUT

OPTICAL IN

GND

(AC–3)

DVD

CABLE

(PLAY)

CD–R

OUT

(REC)

MD/

TAPE

(PLAY)

MD/TAPE

OUT

(REC)

CD–R

MAIN

DVD

SURROUND

SUB

D–TV

WOOFER

/LD

6CH INPUT

SAT

VCR 3 /DVR

CENTER

ZONE 2 OUTDIGITAL

LRR L

VIDEO

DVD

D–TV /LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

VCR 3

/DVR

OUT

VIDEO

MONITOR

OUT

AUDIOAUDIODIGITAL

PHONO

VIDEO

S VIDEO

COMPONENT VIDEO

YPB/CBPR/C

PREOUT/MAIN IN

R L

CONTROL

REMOTE 1

OUT

REMOTE 2

MONO

REAR CTR

RS–

232C

CTRL

OUT

10mA

R L

+12V

MAX.

DVD

D–TV

/LD

SAT

MONITOR

OUT

FRONT

OUT

REAR

(

SURROUND

SUB

WOOFER

SPLIT

CENTER

OUT

MAIN

OUT

)

TUNER

R L

CAUTION

ATTENTION

PREPARATIONS

1 Composite VIDEO jack

Video signals input through the VIDEO jacks are the conventional composite video signals.

2 S VIDEO jack

Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals. The S-video signals achieve high quality color reproduction. When you are using the S VIDEO jacks, check the details in the owner’s manual that came with the component being connected.

3 COMPONENT VIDEO jacks

Video signals input through the COMPONENT VIDEO jacks are separated into luminance (Y) and color difference (PB/CB, PR/CR) video signals. The jacks are also separated into three for each signal. The labels of the component video jacks may be different depending on the component (e.g. Y, C Component video signals provide the best quality in picture reproduction. When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being connected.

B, CR / Y, PB, PR / Y, B-Y, R-Y/ etc.).

Cautions

• Use a commercially available S-video cable when connecting to

the S VIDEO jacks, and commercially available video cables when connecting to the COMPONENT VIDEO jacks.

• Each type of video jack works independently. Signals input through the composite video, S-video, and component jacks are output through the corresponding composite video, S-video, and component jacks respectively.

• If your video monitor is connected only to the COMPONENT VIDEO jacks of this unit, the OSD is not shown.

Note

• You can designate the input for the COMPONENT VIDEO A, B and C jacks according to your component by using “8 I/O ASSIGNMENT” on the SET MENU (see page __ for details).

E-21

English

CONNECTIONS

■ Connecting a DVD player

• Connect the left and right analog signal output jacks on your DVD player to the DVD L and R jacks. Connect the composite video signal

output jack on your DVD player to the DVD VIDEO jack.

• If your DVD player has an S-video output or component video output, you can connect it to this unit. Connect the S-video signal output

jack on your DVD player to the DVD S VIDEO jack or connect the component video signal output jacks on your DVD player to the DVD COMPONENT VIDEO jacks.

• Connect the optical digital signal output jack on your DVD player to the OPTICAL DVD jack.

• Connect the coaxial digital signal output jack on your DVD player to the COAXIAL DVD jack.

OPTICAL OUT

COAXIAL OUT

DVD player

COMPONENT VIDEO OUT

(AC–3)

COAXIAL IN

OPTICAL OUT

OPTICAL IN

CABLE

VCR 3 /DVR

DVD

CD–R

MD/ TAPE

CD–R

DVD

D–TV

/LD

SAT

ANALOG AUDIO

GND

(PLAY)

CD–R

OUT

(REC)

(PLAY)

MD/TAPE

OUT

(REC)

MAIN

SURROUND

SUB

WOOFER

6CH INPUT

PHONO

CENTER

ZONE 2 OUTDIGITAL

OUT

VIDEO

S VIDEO

OUT

AUDIOAUDIODIGITAL

LRR L

DVD

D–TV

/LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

VCR 3

/DVR

OUT

VIDEO

MONITOR

OUT

VIDEO

S VIDEO

OUT

COMPONENT VIDEO

PREOUT/MAIN IN

+12V

YPB/CB PR/CR

R L

CONTROL

REMOTE 1

OUT

REMOTE 2

MONO

REAR CTR

RS–

232C

CTRL

OUT

10mA

R L

MAX.

DVD

D–TV

/LD

SAT

MONITOR

OUT

FRONT

OUT

REAR

(

SURROUND

SUB

WOOFER

SPLIT

CENTER

OUT

MAIN

OUT

)

E-22

CONNECTIONS

■ Connecting a digital TV/TV

• Connect the left and right analog signal output jacks on your digital TV/TV to the D-TV/LD L and R jacks. Connect the composite video

signal output jack on your digital TV/TV to the D-TV/LD VIDEO jack.

• If your digital TV/TV has an S-video output or component video output, you can connect it to this unit. Connect the S-video signal output

jack on your digital TV/TV to the D-TV/LD S VIDEO jack or connect the component video signal output jacks on your digital TV/TV to the D-TV/LD COMPONENT VIDEO jacks.

• Connect the optical digital signal output jack on your digital TV/TV to the OPTICAL D-TV/LD jack.

Digital TV/TV

OPTICAL OUT

COMPONENT VIDEO OUT

PREPARATIONS

(AC–3)

COAXIAL IN

OPTICAL OUT

OPTICAL IN

CABLE

CD–R

MD/ TAPE

CD–R

D–TV

VCR 3

/DVR

DVD

/LD

SAT

ANALOG AUDIO

GND

(PLAY)

CD–R

OUT

(REC)

(PLAY)

MD/TAPE

OUT

(REC)

MAIN

SURROUND

SUB

WOOFER

6CH INPUT

PHONO

CENTER

ZONE 2 OUTDIGITAL

OUT

VIDEO

S VIDEO

OUT

AUDIOAUDIODIGITAL

LRR L

VIDEO

DVD

D–TV

/LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

VCR 3

/DVR

OUT

VIDEO

MONITOR

OUT

VIDEO

S VIDEO

OUT

COMPONENT VIDEO

YPB/C

PREOUT/MAIN IN

CONTROL

REMOTE 1

OUT

REMOTE 2

RS–

232C

CTRL

OUT

10mA

+12V

MAX.

R L

MONO

REAR CTR

R L

PR/C

DVD

D–TV

/LD

SAT

MONITOR

OUT

FRONT

OUT

REAR

SURROUND

(

SUB

WOOFER

SPLIT

CENTER

OUT

MAIN

OUT

)

E-23

English

CONNECTIONS

■ Connecting a cable TV tuner

• Connect the left and right analog signal output jacks on your cable TV tuner to the CABLE L and R jacks. Connect the composite video

signal output jack on your cable TV tuner to the CABLE VIDEO jack.

• If your cable TV tuner has an S-video output or component video output, you can connect it to this unit. Connect the S-video signal output

jack on your cable TV tuner to the CABLE S VIDEO jack or connect the component video signal output jacks on your cable TV tuner to the SAT COMPONENT VIDEO jacks.

• Connect the optical digital signal output jack on your cable TV tuner to the OPTICAL SAT jack.

• Connect the coaxial digital signal output jack on your cable TV tuner to the COAXIAL CABLE jack.

OPTICAL OUT

COAXIAL OUT

Cable TV tuner

COMPONENT VIDEO OUT

(AC–3)

COAXIAL IN

OPTICAL OUT

OPTICAL IN

ANALOG AUDIO

CABLE

CD–R

MD/ TAPE

CD–R

D–TV

VCR 3

/DVR

GND

DVD

(PLAY)

CD–R

OUT

(REC)

(PLAY)

MD/TAPE

OUT

(REC)

MAIN

DVD

SURROUND

SUB

WOOFER

/LD

6CH INPUT

SAT

OUT

PHONO

CENTER

ZONE 2 OUTDIGITAL

VIDEO

S VIDEO

OUT

AUDIOAUDIODIGITAL

LRR L

VIDEO

DVD

D–TV

/LD

CABLE

SAT

VCR 1

OUT

VCR 2

OUT

VCR 3 /DVR

OUT

VIDEO

MONITOR

OUT

VIDEO

S VIDEO

OUT

COMPONENT VIDEO

YPB/C

PREOUT/MAIN IN

CONTROL

REMOTE 1

OUT

REMOTE 2

RS–

232C

CTRL

OUT

10mA

+12V

MAX.

R L

MONO

REAR CTR

R L

PR/C

DVD

D–TV

/LD

SAT

MONITOR

OUT

FRONT

OUT

REAR

(

SURROUND

SUB

WOOFER

SPLIT

CENTER

OUT

MAIN

OUT

)

Cautions

• When connecting the optical digital signal output jack on your cable TV tuner, it is necessary to change the setting for the OPTICAL SAT jack of “8 I/O ASSIGNMENT” on the SET MENU in order to connect the digital audio signals to the SAT jack and the video signals to CABLE jack (see page __).

• When connecting the component video signal output jacks on your cable TV tuner, it is necessary to change the setting for SAT COMPONENT VIDEO jacks of “8 I/O ASSIGNMENT” on the SET MENU in order to connect the audio signals to the CABLE jack and the component video signal to the SAT jack (see page __).

E-24

+ 98 hidden pages