ME02R96
Owner’s Manual
Thank you for your purchase of the YAMAHA ME02R96 memory expansion kit for the 02R96 mixer.
By replacing the original CPU board with this ME02R96 expansion board, you will expand your
mixer’s automix memory to 7MB—a sevenfold increase that will make your mixer even more versatile and even easier to use.
The ME02R96 expansion kit must be installed by an authorized
serviceperson. Please contact a local Yamaha dealer or a service
center to arrange for installation. Do not attempt to install the
ME02R96 on your own.
Please read through the following precautions carefully before having the serviceperson install this
ME02R96 expansion kit. Be sure to retain the manual in a safe place.
Precautions
WARNINGS
Failure to observe the following warnings may lead to fatality or serious injury from fire or
electric shock.
Do not attempt to disassemble or modify the
●
ME02R96 board. Do not apply excessive force to
board connectors or other board components.
(Mishandling of the board may lead to shock, fire
hazard, or equipment failure.)
CAUTIONS
Failure to observe the following cautions may lead to injury, or may result in damage to
equipment or other property.
●
Be sure to unplug the 02R96 main unit from the
power supply before installing the ME02R96
board (to eliminate shock hazard).
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
Be careful to avoid catching or snagging fingers
●
while carrying out the installation.
When handling the ME02R96 board, do not
●
touch the board’s metallic leads (pins). (Pins are
sharp and may cause hand cuts.)
●
The ME02R96 board is electrostatic-sensitive.
Before handling the board, you should briefly
touch the main unit’s metal casing with your bare
hand so as to drain off any static charge from
your body.
Before starting installation, be sure to save all
●
important data from the 02R96 unit to an external
MIDI device. This installation process will clear all
of the unit’s user memory and will reset all settings to their defaults.
●
Be sure to install the included lithium battery. This
is a backup battery that is required maintain the
data in the 02R96’s expanded memory.
ME02R96
1
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated
in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha
may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this
product to accessories and/or another
product use only high quality shielded
cables. Cable/s supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions
could void your FCC authorization to use
this product in the USA.
3. NOTE: This product has been tested
and found to comply with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance
with these requirements provides a reasonable level of assurance that your use
of this product in a residential environment will not result in harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not installed and used
according to the instructions found in the
users manual, may cause interference
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
harmful to the operation of other electronic devices. Compliance with FCC
regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the
source of interference, which can be
determined by turning the unit “OFF”
and “ON”, please try to eliminate the
problem by using one of the following
measures:
Relocate either this product or the
device that is being affected by the interference.
Utilize power outlets that are on different
branch (circuit breaker or fuse) circuits
or install AC line filter/s.
In the case of radio or TV interference,
relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type
cable.
If these corrective measures do not produce satisfactory results, please contact
the local retailer authorized to distribute
this type of product. If you can not locate
the appropriate retailer, please contact
Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or
data that is lost or destroyed.
* Please dispose of used batteries in accordance with local regulations.
* Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of
ENGLISH
the product.
* Company names and product names used herein are trademarks or registered trademarks of their respec-
tive owners.
* Use of the software and this manual is governed by the license agreement which the purchaser fully agrees
to upon breaking the seal of the software packaging. (Please read carefully the important information and
the Software Licensing Agreement of the Studio Manager’s installation guide included with 02R96 before
installing the software.)
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp.
reserves the right to change or modify products or specifications at any time without prior notice. Since
specifications, equipment or options may not be the same in every locale, please check with your Yamaha
dealer.
ADVARSEL!
Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af
samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren.
VARNING
Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som
rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.
NEDERLAND THE NETHERLANDS
●
Dit apparaat bevat een lithium batterij voor
geheugen back-up.
●
Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het
apparaat ann het einde van de levensduur
afdankt of de volgende Yamaha Service
Afdeiing:
Yamaha Music Nederland Service Afdeiing
Kanaalweg 18-G, 3526 KL UTRECHT
Tel. 030-2828425
●
Gooi de batterij niet weg, maar lever hem in
als KCA.
ME02R96
2
●
This apparatus contains a lithium battery for
memory back-up.
●
For the removal of the battery at the moment
of the disposal at the end of the service life
please consult your retailer or Yamaha Service Center as follows:
Yamaha Music Nederland Service Center
Address: Kanaalweg 18-G, 3526 KL
UTRECHT
Tel: 030-2828425
●
Do not throw away the battery. Instead, hand
it in as small chemical waste.
●
Note About Versions and Upgrades
System software:
The ME02R96 includes system version 1.20 or higher, and is not compatible with pre-V1.20 software. Before upgrading your 02R96 again in the future, be sure that your updater program is V1.20
or higher.
Studio Manager:
The ME02R96 is not compatible with Studio Manager versions prior to V1.1.1. If your version is
older than V1.1.1, please replace it by installing the Studio Manager version included on the accompanying CD-ROM. For information about how to carry out the installation, refer to Studio Manager’s
installation guide.
Note that Macintosh system requirements are now as indicated in the table below.
Macintosh System Requirements
Computer A Macintosh G3/233 MHz or better and a USB port
OS Mac OS 8.6 to 9.2.2 (Mac OS X not supported)
Memory 120 MB or more of free memory (Virtual memory must be turned off)
Hard Disk 7 MB or more
Display 1024 × 768 pixels, 256 colors or higher
Other OMS 2.3.3 or later
Note: If you are using a PowerBook on battery power, open the Energy Save
control panel, and in Advanced Settings, Additional Power Savings, turn off
Allow processor cycling.
For the latest information about System software and Studio Manager, please visit our website at:
www
.yamahaproaudio.com.
1280 × 1024, 32,000 colors recommended
ENGLISH
●
Save the Data from the 02R96
The board installation procedure will clear all 02R96 user memory, and will reset all 02R96 settings to
their defaults. Before starting installation, use the following procedure to save the data from the 02R96
into an external MIDI device. You can then restore the data after completing the installation.
As an alternative, you can use Studio Manager to save the 02R96 data into a computer. For details,
refer to the Studio Manager owner’s manual (PDF file).
Press the DISPLAY ACCESS [MIDI] key to open the Bulk Dump page.
1.
Set CATEGORY to ALL, select the TRANSMIT button, and then press the [ENTER] key to
2.
start the save.
ME02R96
3
●
Install the ME02R96 Expansion Kit
~The following instructions are intended for use by authorized servicepersons only.~
ENGLISH
This kit is not user-installable. Users should contact a local
Yamaha dealer or a service center to arrange for installation by a
Yamaha-authorized serviceperson.
Detach and Raise the Control Panel
When removing each screw, note its location and be sure to return it to the same place when reassembling. Screws come in various sizes and are not interchangeable.
1.
Turn off the 02R96 power switch, and unplug the 02R96 power cord from the power supply.
2.
If SP02R96 side panels are installed on the 02R96, remove both of these panels (one from the
left, and the other from the right). To remove each panel, remove 6 screws as shown below
(for a total of 12 screws).
For more information about SP02R96 side panels, refer to the 02R96 owner’s manual.
02R96
4
ME02R96
SP02R96
(Side Panel)
6 Screws
3.
If the MB02R96 peak meter bridge is installed on the 02R96, remove it. First disconnect the
bridge cable from the METER connector on the 02R96. Then remove the 4 screws holding the
bridge in place (as shown below), and remove the bridge.
2 Screws
02R96
METER Connector
ENGLISH
2 Screws
ME02R96
5
4.
Remove the screws indicated in the illustration below: 7 screws from the left side, 7 screws
from the right side, 7 screws from the front, and 7 screws (or 5 screws, if 2 were already
removed at Step 3) from the rear.
<Rear View>
ENGLISH
<Left Side View>
Hold onto the LCD, and lift up the rear of the control panel.
5.
Positioning
Screw
Positioning Screw
LCD
7 Screws
<Top View>
<Front View>
7 Screws
LCD
7 Screws
Positioning Screw
7 Screws
Positioning
Screw
<Right Side View>
Secure the raised control panel in place, so that it does not fall back down.
6.
ME02R96
6
<Top View>
CPU
4 Screws
Lithium Battery
Install the ME02R96 Expansion Board and the Battery
1.
Disconnect the 2 flat cables from the connectors
on the CPU board.
The cables are connected to white connectors.
Before disconnecting each cable, pull the connector latch up as shown in the illustration.
2.
Remove the 4 screws holding the CPU board in place, and remove the CPU board.
3.
Mount the ME02R96 board.
Connect the two black connectors on the underside of the ME02R96 board to the two black
connectors on the 02R96. Then fasten the ME02R96 into place using 4 screws (the 4 screws
you removed above, or the 4 screws included in the kit).
Flat Cable
Latch
ENGLISH
When installing the expansion board, you can use either these 4 screws or else the 4 screws included
in the kit. If you reuse these original screws, you will not need the screws in the kit.
Reconnect the 2 flat cables.
4.
To reconnect: Push the latch down, then insert the cable so that the red line on the cable is
aligned with the ▼ mark on the board.
Install the supplied lithium battery. This is a backup battery that is required to maintain data in
5.
the 02R96 unit’s expanded memory.
ME02R96
7
Reattach the Control Panel
1.
Lower the control panel back into place. Then refasten with the original screws, in the following
order: front panel first, then the sides, and then the rear. When fastening each panel, always
fasten the positioning screw first (see illustrations on page 6 above).
ENGLISH
2.
●
If you saved the 02R96 data to an external MIDI device as described on page 3 above, you can now
restore that data as follows.
1.
2.
3.
●
Before screwing in the control panel, check to make sure that you have not left any loose screws or
tools inside the 02R96 casing. Loose objects left in the casing may cause damage to the equipment.
If applicable:
reversing the removal procedures given on page 4 and 5 above.
Reinstall the MB02R96 peak meter bridge and/or the SP02R96 side panels by
Restoring the Saved 02R96 Data
After completing the kit installation, turn on the 02R96 power. The start-up screen displays the
message
Press the DISPLAY ACCESS [MIDI] key to open the Bulk Dump page.
Set the CATEGORY to ALL, select the REQUEST button, and then press the [ENTER] key.
MEMORY EXPANDED
It is not possible to load automix data that exceeds the mixer’s automix memory capacity (7MB with
the ME02R96 installed; 1MB if it is not installed). If you attempt to load such data, the 02R96 will display an appropriate message and will execute the load. Any data already existing in the 02R96 will
remain unchanged.
.
Kit Contents
ME02R96 Expansion Board
Lithium battery
4 Screws
ME02R96 Owner’s Manual (this booklet)
CD-ROM (Studio Manager)
European models
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Conforms to Environments: E1, E2, E3 and E4
ME02R96
8
http://www2.yamaha.co.jp/manual/english/
Yamaha Manual Library
Loading...