Yamaha MCRN560SBR, MCRN560BBR, MCRN560SBG, MCRN560BBG User Manual

N e t w o r k C D R e c e i v e r

O W N E R ’ S M A N UA L

Rea d th e su pp li ed b oo kl et “S af et y Br oc hu re ” be fo re u si ng t he u ni t.

Contents

Introduction......4

Supplied accessories......4

About this manual......4

Part name......5

Front panel......5

Rear panel......6

Front panel display......7

Adjusting display brightness......7

Remote control......8

Preparations......9

Connecting the speakers......9

Connecting antenna......10

Connecting to the network......11

Turning on the power......12

Setting the network devices......13

PC......13

NAS......13

Mobile devices......13

Listening to CD......14

Listening to iPod/USB devices......15

Playing iPod......15

Playing USB devices......15

Listening to the songs in the computer

Setting the media sharing of music files......17

Playing back songs in the PC......18

......17

Listening to external sources......19

Introduction

Confirm the package contents and useful points of this manual.

Supplied accessories

DAB/FM antenna

Remote control

• Change both batteries when the operation range of the remote control decreases.

Batteries (× 2) (AA, R6, UM-3)

Check the “+” and “-” of the batteries and inset them the correct way around.

About this manual

• How to operate this unit is described mainly using the remote control.

• Illustrations may differ from actual item depicted.

• “iPod” described in this manual may also refer to

“iPhone” or “iPad.”

• Symbols:

Indicates precautions for use of the unit and its feature limitations. Indicates supplementary explanations for better use.

Indicates the corresponding reference page(s).

4 En

Part name

Familiarize yourself with all parts and these functions.

Front panel

1 Remote control receiver 2 INPUT

Turn left or right to change the audio source. (The source is shown on the front panel display.)

3 (& P.14, 16, 18)

PRESET</> (& P.27)

4 A (Power) (& P.12) 5 PHONES

Connect headphones to this jack.

6 Disc tray (& P.14) 7 USB jack (& P.15) 8 (Stop) (& P.14, 16, 18, 29) 9 (Open/close the disc tray) (& P.14) 0 VOLUME

Controls the volume.

A (Play/pause) (& P.14, 16, 18) B Front panel display (& P.7)

En 5

Part name

Rear panel

1 Power cable (& P.12) 2 DC OUT terminal

Supplies power to the Yamaha AV accessories from this terminal. When using this, set [Use Accessory] in [System Config] from the option setting, to [YES] (& P.35). For details, refer to the owner’s manual supplied with the accessory.

3 NETWORK terminal (& P.11)

Connects to a network using a commercially available network cable.

4 DAB/FM antenna terminal (& P.10) 5 DIGITAL IN 1 terminal (optical input) (& P.19) 6 DIGITAL IN 2 terminal (coaxial input) (& P.19) 7 AUX 1 terminal (RCA input) (& P.19) 8 AUX 2 terminal (mini jack input) (& P.19) 9 SUBWOOFER terminal (& P.9) 0 SPEAKERS terminal (& P.9)

6 En

Front panel display

Part name

1 Clock

Displays the time when the power is on.

2 TUNED indicator

Lights up when the unit is tuned into a station.

3 Multi information display

Shows various information, such as the clock in standby mode, music information, or radio frequency (alphanumerics only).

4 MUTE indicator

Lights up when the sound is muted (& P.8).

5 Wake-up timer indicator

Blinks while setting the wake-up timer and lights up when the timer is set (& P.32).

6 Sleep timer indicator

Lights up when the sleep timer is set (& P.33).

7 Shuffle/repeat indicator

Lights up when you set your iPod, CD, USB device, or computer to shuffle or repeat playback (& P.20).

8 STEREO indicator

Lights up when the unit is receiving a strong signal from an FM stereo broadcast.

9 Operation indicators

Shows available control buttons S/T/ENTER (& P.8) of the remote control.

0 2nd indicator

Appears when the DAB station has a secondary station (& P.23).

Adjusting display brightness

You can adjust the brightness of the front panel display by pressing the DIMMER button on the remote control (& P.8).

• Each press of the button changes the brightness: bright (default), mid dim, or dim.

En 7

Part name

Remote control

1 Infrared signal transmitter

2 (Open/close the disc tray) (& P.14) 3 Source buttons

Switch the audio source to be played.

4 Numeric buttons (& P.14) 5 HOME (& P.16, 18, 29) 6 RETURN (& P.14, 16, 18, 29) 7 Audio control, cursor control buttons

(& P.14, 16, 18, 29)

8 DISPLAY (& P.21) 9 (SHUFFLE) (& P.20) 0 DAB/FM control buttons (& P.23, 24, 26, 27) A DIMMER (& P.7) B A (Power) (& P.12) C OPTION (& P.22, 25, 31, 35) D NOW PLAYING (& P.16, 18, 29) E VOLUME +/–

Controls the volume.

F MUTE

Turns mute on or off.

G (REPEAT) (& P.20) H TIMER (& P.32) I SLEEP (& P.33)

8 En

Preparations

Connect speakers or antenna and turn the unit on.

Do not connect the power cable of the unit until you have finished connecting all cables.

Connecting the speakers

1 Remove the insulation from the end of

the speaker cable to expose the bare wires.

15 mm (5/8 in.)

2 Connect the speaker to the unit, as the

illustration shows.

• Prepare speakers and speaker cables separately.

• For connection of the speakers, refer to the

owner’s manual supplied with them.

Right speaker

Left speaker

Speaker

cable

• Take care not to allow the bare speaker wires to touch each other or any metal part of the unit. This could damage the unit and/or the speakers.

• Make sure that left and right (L, R) connections and polarity (red: +, black: -) are correct. If connections are incorrect, the sound will be unnatural.

• Use speakers of at least 6 Ω impedance.

• You can also connect a subwoofer with built-in amplifier to the unit.

Subwoofer

Monaural pin cable

En 9

Preparations

Connecting antenna

1 Connect the supplied antenna to the

unit.

2 Install it with pins where the unit can

obtain good reception.

Supplied antenna

10 En

• Be sure to stretch out the antenna as the illustration shows.

• If radio reception with the supplied antenna is not satisfactory, a commercially available outdoor antenna may improve

reception.

Preparations

Connecting to the network

You can play back music files stored on your PC, mobile devices, DLNA*-compatible NAS, or audio contents on the Internet, by connecting this unit to the network. You can also operate the unit with your mobile device.

* Digital Living Network Alliance

Connect the unit to the network as shown on the right.

• Connect with a commercially available STP (shielded twisted pair) network cable (CAT-5 or higher, straightthroughcable).

This unit

LAN

Broadband

router

Internet

• For details on Internet connection, refer to the owner’s manuals of your network devices.

• If you are using a router that supports DHCP, you do not need to configure any network settings for the unit. If you are

using a router that does not support DHCP, configure the network setting from [Network Config] in the option setting (& P.35).

• Wired connections are recommended for devices other than the mobile to ensure high sound quality.

• Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the

access of the unit to the network devices or the Internet. In this case, change the setting of the security software or network devices.

• When setting the subnet manually, each server must be connected to the same subnet as the unit (& P.36).

Modem

WAN

Network cable

Mobile device

Network attached

storage (NAS)

En 11

Preparations

Turning on the power

Plug the power cable into the wall outlet and press .

• The unit turns on.

• Press again to turn off (standby mode).

• “Eco standby” (default) reduces power consumption of

the unit while limiting certain features (as shown in the table on the right).

Canceling the eco standby

Status in standby/eco standby

Standby Eco standby

Charging of iPod/USB devices 3 —

Enable/disable the wake-up

Within 6 m

(20 ft)

timer*

Operation of the source buttons*

CD load/eject 33

AirPlay 3 —

Power-on by the application 3 —

Clock display 3 —

* Operation with the remote control only

3 —

1 Press .

• Option menu is shown on the front panel display.

2 Cancel the eco standby.

• Set the item in the order of [System Config] [Power Saving] - [Normal].

• Change the item with S/T and press to set.

3 Press to finish the option setting.

12 En

1, 3

OPTION

S/T, ENTER

Option menu regarding power (System Config)

(Setting value. Bold: default)

Power Saving

Configure the power supply settings. (Normal, Eco) When you select [Eco], nothing is shown on the front panel display in the eco standby mode.

Auto Power Off

Set the time at which the unit enters standby mode if no operation is performed. (Timer 2H, Timer 4H, Timer 8H, Timer 12H, OFF)

Setting the network devices

Configure your devices connected to the network to play back music files stored on your PC or NAS, or configure your mobile device to control this unit.

Configure the media sharing setting of your PC (& P.17).

NAS

Configure the settings to access your NAS.

• Enable DHCP setting of your NAS if needed.

• For more detailed settings, refer to the owner’s manual

supplied with your NAS.

Mobile devices

Install the dedicated application “NETWORK PLAYER CONTROLLER” to your mobile devices (& P.18).

• The application supports iPhone/iPad/iPod touch and Android mobile devices.

• The mobile device needs to be connected to the same router as the unit.

En 13

Listening to CD

This unit allows playback of audio CDs and data CDs in which the MP3/WMA files are recorded. For details on playable CDs, see “Supported devices/medias” (P.43).

1 Turn INPUT to select [CD]. Or, press

on the remote control.

2 Set a CD in a disc tray.

• Press to open/close the disc tray.

3 Playback starts.

• The remote control functions are shown below.

S T

1 - 9, 0 Specify the song number.

RETURN Cancel the song number.

ENTER Apply the song number.

Skip to the first file of the previous or next folder when playing back MP3/ WMA files.

Play/pause

Stop

Skip to the beginning of the song being played back or the previous song.

Skip to the next song.

Starts shuffle playback (& P.20).

Starts repeat playback (& P.20).

INPUT

• Files on a data CD are played back in alphanumeric order.

• When CD playback is stopped, playback will resume from the beginning of the song last played. Pressing while playback is stopped will clear resume playback.

14 En

Listening to iPod/USB devices

This unit allows playback of iPod or USB devices which music files are recorded. For details on playable iPod/USB devices, see “Supported devices/media and file formats” (P.43).

Playing iPod

1 Turn INPUT to select [USB] or press

on the remote control.

2 Connect the iPod to the USB jack.

• Prepare the USB cable supplied with your iPod.

• The source changes to [iPod].

3 Playback starts (& P.16).

Playing USB devices

1 Turn INPUT to select [USB]. Or, press

on the remote control.

2 Connect a USB device to the USB port. 3 Playback starts (& P.16).

INPUT

• Some iPods/USB devices may not work properly even if they meet the requirements. Playability of and power supply to all iPods/USB devices are not guaranteed.

• Yamaha and suppliers do not accept any liability for the loss of data saved on an iPod or a USB device connected to the unit. As a precaution, it is recommended to make backup copies of important files.

• Stop playback before disconnecting the USB device.

• An iPod or USB device is automatically charged when it is connected to the unit, except in the eco standby mode.

USB

En 15

+ 35 hidden pages