Yamaha MCR-040-140 User Manual
U
MICRO COMPONENT SYSTEM
MICRO-CHAINE
OWNER’S MANUAL
MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain
this Owner’s Manual in a safe place for future reference.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
i En
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2 IMPORTANT:
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
When connecting this product to
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
The following information applies for MCR-140 only.
• This equipment compiles with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules.
This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation
(MPE). But it is desirable that it should be installed and operated with at least 20 cm and more between the radiator and person's
body (excluding extremities: hands, wrists, feet and ankles).
• This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
ii En
Caution: Read this before operating your unit.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances
around CRX-040/140.
Top: 10 cm (4 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
13 To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press to set this unit to the
standby mode, and disconnect the AC power plug from
the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like. When you dispose of
batteries, follow your regional regulations.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by . This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam. When this unit is plugged into the wall
outlet, do not place your eyes close to the opening of the disc tray
and other openings to look into inside.
The laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Do not use MCR-140 within 22 cm (9 in) of persons with a heart
pacemaker implant or defibrillator implant.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot
and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
iii En
CONTENTS
PREPARATION
PARTS.....................................................................2
PLAYABLE DISCS AND FILE FORMAT......... 3
CONNECTION....................................................... 4
Basic connection........................................................4
Wireless connection ...........................5
Other connection........................................................5
REMOTE CONTROL ........................................... 6
FRONT PANEL DISPLAY ................................... 6
MCR-140
OPERATION
FRONT PANEL AND BASIC OPERATION ..... 7
LISTENING TO MUSIC....................................... 8
Playback operation.....................................................8
Other operation..........................................................9
LISTENING TO FM RADIO STATIONS ........10
Tuning to radio stations ...........................................10
Presetting radio stations...........................................10
Selecting preset radio stations (Preset tuning)......... 10
USING USEFUL FUNCTIONS .......................... 11
Using setup menu ....................................................11
Using timer and sleep timer..................................... 13
ADDITIONAL INFORMATION
TROUBLESHOOTING .......................................14
General..................................................................... 14
Radio reception........................................................ 15
iPod™......................................................................15
USB ......................................................................... 18
Disc playback ..........................................................19
Remote control ........................................................ 19
HANDLING COMPACT DISCS ........................20
SPECIFICATIONS...............................................20
PREPARATION OPERATION
INFORMATION
ADDITIONAL
■ About this manual
• This manual describes how to operate this unit using a remote control except when it is not available. Some of these
operations are also available using the front panel buttons.
• The symbol “☞” with page number(s) indicates the corresponding reference page(s).
• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of
improvements, etc. In case of differences between the manual and the product, the product has priority.
■ Copyright and logo marks
Advanced YST
In 1988, Yamaha brought to the marketplace speaker systems
utilizing YST (Yamaha Active Servo Technology) to give
powerful, high quality bass reproduction. This technique uses a
direct connection between the amplifier and speaker, allowing
accurate signal transmission and precise speaker control.
As this technology uses speaker units controlled by the negative
impedance drive of the amplifier and resonance generated
between the speaker cabinet volume and port, it creates more
resonant energy (the “air woofer” concept) than the standard bass
reflex method. This allows for bass reproduction from much
smaller cabinets than was previously possible.
yAired
Real-time uncompressed music transfer without sound
degradation is realized by Yamaha original digital wireless
transfer technology, yAired. You can also control turning on/
standby and volume with the iPod by yAired.
MCR-140
English
1 En
PREPARATION
Make sure you have all of the following items.
PARTS
MCR-040
CD receiver
(CRX-040)
Dock cover
MCR-140
(CRX-140)
■ Using the remote control
Cover the iPod dock when not using.
TransmitterCD receiver
Use the remote control within 6 m (20’) of this unit and point it toward the
remote control sensor.
+
Remote control
+
Speakers
(NS-BP80)
Indoor FM antenna
Speaker cable
(1.5 m (4.9’) × 2)
Within 6 m
(20’)
Notes
• Do not spill liquid on the remote control.
• Do not drop the remote control.
• Do not leave the remote control in the following places:
– hot or humid places such as a bathroom or near a heater
– extremely cold places
– dusty places
■ Replacing the battery in the remote control
Change the battery when the operation range of the remote control decreases.
Straight pin
CR2025 battery
2 En
PLAYABLE DISCS AND FILE FORMAT
■ Playable discs
Use compact discs bearing the marks below.
....
Compact discs (digital audio)
....
CD-R,CD-RW digital audio discs
• CD-R or CD-RW discs bearing one of
the following phrases.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• Finalized CD-R or CD-RW discs
Note
This compact disc player may not be able to
play some CD-R/CD-RW discs or discs on
which recording was not made correctly.
....
CD-TEXT discs
To play back an 8-cm (3 in) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal (12-cm) CD on top of an 8-cm (3 in) CD.
To prevent a malfunction of this unit:
• Do not use any nonstandard shaped
disc (heart, etc.) available on the
market because it might damage the
unit.
• Do not use a disc with tape, stickers, or paste on it. If
you use such a disc, the disc may get stuck in the
unit, or damage to the unit may result.
Note: Do not use any lens cleaners as they may be a
cause of malfunction.
■ Playable MP3 and WMA files
MP3
Format
MPEG 1 Audio Layer-3
MPEG 2 Audio Layer-3, 2
*1Variable bitrate is supported.
Bitrate
(kbps)
32-320
8-160
WMA
• Version 8
• Version 9 (Standard and variable bitrates are supported.
Professional and Lossless are not supported.)
Profile
High Profile
Mid Profile
*2Both constant and variable bitrates are supported.
Bitrate
(kbps)
32-320
16-32 22.05
Notes
• Playback for Data Disc starts in alphanumeric order of files.
• Playback for USB starts in order by date and time of creation.
• Copyright-protected WMA (DRM) files cannot be played back
by this unit.
• The disc must be ISO 9660 compatible.
• The maximum file and folder numbers are as follows.
Data Disc USB
Maximum total number of file
and folder
Maximum folder number
Maximum file number per
folder
3
The root is counted as one of the folders.
*
*3
*3
Sampling
frequency
(kHz)
*1
32/44.1/48
*1
16/22.05/24
Sampling
frequency
(kHz)
*2
32/44.1/48
512 9,999
255 255
511 255
PREPARATION
3 En
English
CONNECTION
Basic connection
Follow the procedure below to connect the speakers and indoor FM antenna to this unit.
CAUTION
Do not connect the power cable of this unit until all cable connections are completed.
Indoor FM antenna
Notes
To the wall outlet
• The antenna should be stretched out.
• If radio reception is poor, change the height,
direction, or placement of the antenna.
• If you use an outdoor antenna instead of the
supplied FM antenna, reception will be better.
Notes
• Be sure to connect the left channel (L), right channel (R), “+”(red) “–”(black) properly. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass.
• Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/
or the speakers.
• Use the supplied speakers only. Using different speakers may cause the sound to differ from the intended design.
• There is a chance that placing speakers too close to a CRT-based (Braun tube) TV set might impair picture color. Should this happen,
move the speakers away from the TV set.
4 En
Loading...