Yamaha M7CL V11 User Manual
M7CL V1.10 Supplementary Manual
M7CL firmware V1.10 contains the following changes and additions relative to
V1.05. (Changes in V1.06 are also included here.)
* The Help function in V1.10 and later of this product uses bitmap fonts from the Ricoh Corporation.
•You can now reset the GAIN to the default value (0.0
Changes in V1.06
• Speed of synchronization with M7CL Editor has been
improved.
• In the ATT/HPF/EQ popup window (1ch) and the
DYNAMICS popup window (1ch), the location of the
ON button has been distanced from the “ × ” (close) button in order to prevent accidental operation.
• By pressing a GEQ fader in the GEQ popup window,
you can now switch the faders assigned to the Centralogic section. The numbers of the assigned faders are
shown on the GEQ faders.
• The position of the window has been improved so that
the channel number and channel name field at the bottom of the display can be seen even when a popup window or the SCENE LIST window is displayed.
Changes in V1.10
• When you use the SAVE/LOAD screen to save all of the
M7CL’s internal data (except for user authentication key
data) in a single operation, the user level, user-defined
keys, and preference settings of the administrator and
guest will also be saved. On the M7CL console, this
data can be loaded only when the administrator logs in.
In M7CL Editor (V2.1.1 or later), this data can be read
at any time. However on earlier versions of the M7CL
console or M7CL Editor, this data that was saved in
V1.10 or later cannot be read.
•You can now view the M7CL’s Help by pressing the
(Help) button in the function access area. For
details, refer to “Using the Help function.”
• The assigned user-defined key will now blink while
you’re viewing a screen or popup window that’s bookmarked by a user-defined key.
dB) for each band by simultaneously pressing the
SELECTED CHANNEL section EQ [Q] encoder and
EQ [GAIN] encoder.
• The following have been added as parameters that can
be assigned to the user-defined keys.
FUNCTION
SET BY
SEL
SET BY
SEL
HELP — —
PARAME-
TER 1
SET
[INSERT
ON]
SET
[DIRECT
OUT ON]
PARAME-
TER 2
—
—
Description
By holding down this key
and pressing the [SEL] key
of a channel, that channel’s INSERT ON can be
switched on/off.
By holding down this key
and pressing the [SEL] key
of a channel, that channel’s DIRECT OUT ON
can be switched on/off.
Opens or closes the HELP
popup window. If you hold
down this key and operate
a panel controller (except
for the faders) or an onscreen controller, the corresponding explanation
will appear.
• PRE FADER (immediately before the fader) has been
added as a position for direct output from an INPUT
channel.
• If you’re using the M7CL V1.10, you must use V2.1.1
or later of M7CL Editor. You can download the most
recent version of M7CL Editor from the following website.
http://www.yamahaproaudio.com/
EN
Using the Help function
You can view the Help file provided by Yamaha, or you
can view any desired text file created by a user.
*We accept no responsibility for any damages that may occur
as a result of using help files created by a third party other
than Yamaha.
■ Loading a Help file from a USB storage
To select the Help file you want to load,
4
press one of the Help files shown in the file
list, or turn multi-function encoder 1 on the
panel.
Press the LOAD button; a confirmation dia-
5
log box will appear.
Press the OK button to load the file.
6
device
NOTE
• The help file is not backed up in internal user memory. Each time
you turn on the power, you must reload it from your USB storage
device. It is convenient to save your help file on the USB storage
device that contains your user authentication key.
Before you proceed, save the Help file
1
(extension .xml) provided by Yamaha on
your USB storage device. You can download the most recent version of the Help file
from the Yamaha website.
http://www.yamahaproaudio.com/
In the function access area, press the
2
SETUP button to access the SETUP screen.
SAVE/LOAD button
■ Loading a text file from a USB storage
device
Using a commercially available text editor
1
or the “Notepad” included with the
Microsoft Windows series, create a text file
(extension .txt) and save it on your USB
storage device.
By default, the character code set of the text file will
be detected as UTF-8. However by adding a line consisting of [ISO-8859-1] or [Shift_JIS] at the beginning
of the file, you can force recognition of the file using
that character code set. You can specify the desired
character code set when using your text editor to save
the text file.
The Help function is able to display the following text
files (character code sets / languages).
•Text files written in the ISO-8859-1 character code
set (English, German, French, Spanish, etc.)
•Text files written in the Shift_JIS character code set
(Japanese)
•Text files of the above languages written in the UTF-8
character code set.
Press the SAVE/LOAD button to access the
3
SAVE/LOAD popup window.
In the function access area, press the
2
SETUP button to access the SETUP screen.
Press the SAVE/LOAD button to access the
3
SAVE/LOAD popup window.
To select the text file you want to load,
4
press one of the text files shown in the file
list or turn multi-function encoder 1 on the
panel.
Press the LOAD button; a confirmation dia-
5
log box will appear.
Press the OK button to load the file.
6
Loading...