Yamaha M7CL-32, M7CL-48ES, M7CL-48 User Manual

M7CL StageMix User Guide

Welcome:

Thank you for downloading the “M7CL StageMix” iPad app for the Yamaha M7CL V3
digital mixing console. Via a wireless access point, StageMix can control any variant
of M7CL console so long as it is running V3 firmware.
The latest firmware version for M7CL can be downloaded from

www.yamahaproaudio.com

StageMix provides remote control of M7CL functions via a simple, intuitive
graphical interface from anywhere within wireless range. The software has
been specifically designed to allow engineers to adjust monitor mixes from
the performers’ positions on stage, directly controlling mix parameters via the
iPad rather than having to rely on verbal directions to a second engineer.
The result is better mixes in less time: a huge advantage during high-pressure
pre-show setup. StageMix does not provide remote control of all M7CL
parameters, but is focused on the requirements for adjusting monitor mixes on
stage.

Yamaha Commercial Audio M7CL StageMix User Guide

CONTENTS

Page

1.0 System Requirements 3

2.0 WiFi Settings 3

3.0 Getting Started 4

3.1 M7CL Network Setup 4

3.2 iPad Settings 4

3.3 StageMix Setup 5

3.3.1 Offline Demo Mode 6

3.3.2 Configure StageMix to Work with an M7CL 6

3.3.3 Select a Mixer and Begin Working 7

4.0 StageMix Operation 8

4.1 Mixer Window 8

4.1.1 Channel Names 8

4.1.2 Faders 9

4.1.3 Channel ON 9

4.1.4 CUE 9

4.2 SETUP 10

4.2.1 Fader Delay 10

4.2.2 Filled EQ Graph 10

4.3 Long Faders 10

4.4 SENDS ON FADERS 11

4.4.1 Mix Sends ON 12

4.5 EQ Editing 12

4.5.1 HPF 14

4.5.2 EQ Bands 1 & 4 14

4.5.3 EQ ON 14

4.5.4 EQ FLAT, EQ DEFAULT 14

5.0 Troubleshooting 15

5.1 No WiFi Available 15

5.2 Connection Failed to M7CL 15

5.3 Connection Lost 16

Page 2

Yamaha Commercial Audio M7CL StageMix User Guide

1.0 System Requirements

• Apple iPad (any model)

• Yamaha M7CL digital mixing console with V3 firmware (any model, including

M7CL-48, M7CL-32, M7CL-48ES)

• WiFi access point (preferably with 802.11n, 5GHz capability, though 2.4GHz
and 802.11g will also work)

• CAT5 cable (to connect M7CL to WiFi access point)

2.0 WiFi Settings

Configure the WiFi access point, following the manufacturer’s instructions. No
special settings are needed, but using security such as WPA is highly recommended,
to prevent unwanted devices from joining the network. Here are some suggested
settings to assist less experienced WiFi users:

1. Give the wireless network a name (this is the “SSID”).

2. Choose a security mode (such as WPA) and password.

3. Select the wireless mode (802.11g or n).

4. In the case of “n”, select the wireless band (2.4 or 5GHz).

5. If available, enable “Auto Channel Selection” so the wireless channel with the
least interference will be selected.

802.11n networks at 5GHz are preferred because they allow faster communication
between the iPad and the WiFi access point. Practically, this could result in more
accurate level metering with the StageMix app. Also, with 802.11n being a new
standard, it is less prone to interference from other wireless networks. Using a WiFi
access point with 2 or more external aerials is recommended to increase potential
signal range. Booster aerials could be connected for a further increase in
performance.

Page 3

Yamaha Commercial Audio M7CL StageMix User Guide

3.0 Getting Started

3.1 M7CL Network Setup

I. Connect the WiFi access point to the M7CL’s network port via a CAT5 cable.

Note that a cross-over cable will be needed with older access points that don’t
have the “auto MDIX” function. Most recent devices will support “auto MDIX”,
in which case a straight CAT5 cable can be used.

II. Note the IP address and MAC address of the M7CL - they will need to be

entered into the iPad later. They can be found in the console as follows:

a. Press SETUP on the M7CL touchscreen
b. Press [NETWORK] on the M7CL touchscreen

3.2 iPad WiFi Settings

The iPad needs to be given a static IP address in the same range as the
M7CL’s IP Address.

a. Open the iPad “Settings” menu
b. Select “WiFi”, and choose the correct network (with the SSID and

password given in step 2 above).

c. Press the blue circle with the white arrow to the right of the selected

network to edit the IP address.

Page 4

Yamaha Commercial Audio M7CL StageMix User Guide

d. Select [Static].

e. Write an IP Address similar to the one for the M7CL, but with just the

last number different. (For example, if M7CL is 192.168.0.128, give an

address to the iPad such as 192.168.0.127).
f. Enter “255.255.255.0” for the Subnet Mask.
g. Press the iPad’s Home button to exit the Settings menu.

3.3 StageMix Setup

Launch the “M7CL StageMix” App

The “Select Mixer” screen will appear. From this screen, you can do any of
the following things:

• Access the OFFLINE DEMO mode to explore the features and user
interface of M7CL StageMix.

• Configure StageMix to work with an M7CL console.

• Select an M7CL console that has already been configured to work with

your iPad and begin using StageMix.

Page 5