Yamaha F15A, F9.9C, FT9.9D User Manual

Download

Page 1

OWNER’S MANUAL

F9.9C FT9.9D F15A

66M-28199-7C-E0

Page 2

EMU25051

Read this owner’s manual carefully before operating or working on your

outboard motor. Keep this manual onboard in a waterproof bag when boating. This manual should stay with the outboard motor if it is sold.

Page 3

Important manual information

EMU25103

To the owner

Thank you for choosing a Yamaha outboard motor. This Owner’s Manual contains information needed for proper operation, maintenance and care. A thorough understanding of these simple instructions will help you obtain maximum enjoyment from your new Yamaha. If you have any question about the operation or maintenance of your outboard motor, please consult a Yamaha dealer. In this Owner’s Manual particularly important information is distinguished in the following ways.

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

EWM00780

WARNING

Failure to follow WARNING instructions could result in severe injury or death the machine operator, a bystander, or a person inspecting or repairing the outboard motor.

ECM00700

CAUTION:

A CAUTION indicates special precautions that must be taken to avoid damage to the outboard motor.

al, please consult your Yamaha dealer. To ensure long product life, Yamaha recommends that you use the product and perform the specified periodic inspections and maintenance by correctly following the instructions in the owner’s manual. Any damage resulting from neglect of these instructions is not covered by warranty. Some countries have laws or regulations restricting users from taking the product out of the country where it was purchased, and it may be impossible to register the product in the destination country. Additionally, the warranty may not apply in certain regions. When planning to take the product to another country, consult the dealer where the product was purchased for further information. If the product was purchased used, please consult your closest dealer for customer reregistration, and to be eligible for the specified services.

NOTE:

The F9.9CE, F9.9CMH, FT9.9DE, FT9.9DMH, F15AMH and the standard accessories are used as a base for the explanations and illustrations in this manual. Therefore some items may not apply to every model.

EMU25121

NOTE:

A NOTE provides key information to make procedures easier or clearer.

Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your machine and this manual. If there is any question concerning this manu-

F9.9C, FT9.9D, F15A

OWNER’S MANUAL

1st Edition, April 2007

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Co., Ltd. is expressly prohibited.

Printed in Japan

Page 4

Table of contents

General information .......................... 1

Identification numbers record.......... 1

Outboard motor serial number .......... 1

Key number....................................... 1

EC label........................................... 1

Emission control information ........... 2

SAV models ......................................2

Read manuals and labels................ 3

Warning labels ..................................3

Safety information............................. 6

Safety information ........................... 6

Rotating parts.................................... 6

Hot parts ........................................... 6

Electric shock.................................... 6

Engine shut-off cord.......................... 6

Gasoline............................................ 6

Gasoline exposure and spills ............ 6

Carbon monoxide.............................. 6

Modifications ..................................... 6

Boating safety ................................. 7

Alcohol and drugs .............................7

Personal flotation devices ................. 7

People in the water ...........................7

Passengers ....................................... 7

Overloading....................................... 7

Avoid collisions ................................. 7

Weather ............................................ 8

Passenger training ............................ 8

Boating safety publications ...............8

Laws and regulations ........................ 8

Basic requirements........................... 9

Fueling instructions ......................... 9

Gasoline............................................ 9

Engine oil ..........................................9

Installation requirements ............... 10

Boat horsepower rating................... 10

Mounting motor ............................... 10

Battery requirement ........................ 10

Propeller selection .......................... 11

Start-in-gear protection ................. 11

Basic components ..........................12

Main components.......................... 12

Fuel tank .........................................13

Fuel joint ......................................... 14

Fuel gauge ......................................14

Fuel tank cap................................... 14

Air vent screw.................................. 14

Remote control................................ 14

Remote control lever ....................... 14

Neutral interlock trigger ................... 15

Neutral throttle lever........................ 15

Choke switch................................... 15

Tiller handle..................................... 15

Gear shift lever................................ 16

Throttle grip ..................................... 16

Throttle indicator .............................16

Throttle friction adjuster................... 17

Engine shut-off switch ..................... 17

Engine stop button ..........................18

Choke knob for pull type .................18

Manual starter handle .....................18

Starter button ..................................18

Main switch .....................................19

Steering friction adjuster .................19

Steering friction adjuster .................20

Trim rod (tilt pin) .............................. 20

Tilt lock mechanism......................... 20

Tilt support bar ................................20

Top cowling lock lever(s) (turn

type) .............................................. 21

Flushing device ...............................21

Warning indicator ............................21

Warning system ............................ 21

Low oil pressure warning ................22

Operation ......................................... 23

Installation..................................... 23

Mounting the outboard motor .......... 23

Clamping the outboard motor.......... 24

Breaking in engine ........................ 25

Procedure for 4-stroke models........ 25

Pre-operation checks.................... 26

Fuel .................................................26

Controls........................................... 26

Stop switches .................................. 26

Engine ............................................. 26

Checking the engine oil level ..........26

Filling fuel...................................... 27

Operating engine .......................... 27

Feeding fuel (portable tank) ............27

Page 5

Table of contents

Starting engine................................ 28

Warming up engine ....................... 32

Manual start and electric start

models .......................................... 32

Shifting .......................................... 32

Stopping boat ................................ 34

Stopping engine ............................ 34

Procedure ....................................... 34

Trimming outboard motor.............. 35

Adjusting trim angle for manual tilt

models .......................................... 35

Adjusting boat trim ..........................36

Tilting up and down ....................... 37

Procedure for tilting up (manual tilt

models) ......................................... 37

Procedure for tilting down (manual

tilt models) .................................... 38

Cruising in shallow water .............. 38

Cruising in shallow water (manual

tilt models) .................................... 39

Cruising in other conditions........... 40

Maintenance..................................... 41

Specifications ................................ 41

Transporting and storing outboard

motor ........................................... 43

Clamp screw mounting models....... 43

Storing outboard motor ...................44

Procedure ....................................... 44

Lubrication ...................................... 45

Battery care..................................... 46

Flushing power unit......................... 46

Cleaning the outboard motor .......... 47

Checking painted surface of

motor............................................. 47

Periodic maintenance.................... 48

Replacement parts.......................... 48

Severe operating conditions ........... 48

Maintenance chart 1 ....................... 49

Maintenance chart 2 ....................... 51

Greasing ......................................... 52

Cleaning and adjusting spark

plug ............................................... 54

Checking fuel system...................... 54

Inspecting fuel filter ......................... 55

Cleaning fuel filter ...........................55

Inspecting idling speed.................... 56

Changing engine oil ........................56

Checking wiring and connectors .....58

Exhaust leakage.............................. 58

Water leakage ................................. 58

Engine oil leakage........................... 58

Checking propeller ..........................59

Removing propeller ......................... 59

Installing propeller ........................... 60

Changing gear oil ............................ 61

Cleaning fuel tank ...........................62

Inspecting and replacing

anode(s)........................................63

Checking battery (for electric start

models) ......................................... 63

Connecting the battery .................... 64

Disconnecting the battery................ 65

Checking top cowling ......................65

Coating the boat bottom.................. 65

Trouble Recovery............................ 66

Troubleshooting ............................ 66

Temporary action in emergency ... 69

Impact damage ...............................69

Replacing fuse ................................69

Starter will not operate ....................70

Emergency starting engine .............70

Treatment of submerged motor .... 72

Procedure........................................ 72

Page 6

General information

EMU25170

Identification numbers record

EMU25183

Outboard motor serial number

The outboard motor serial number is stamped on the label attached to the port side of the clamp bracket. Record your outboard motor serial number in the spaces provided to assist you in ordering spare parts from your Yamaha dealer or for reference in case your outboard motor is stolen.

1. Outboard motor serial number location

1. Key number

EMU25202

EC label

Engines affixed with this label conform to certain portions of the European Parliament directive relating to machinery. Refer to the label and the EC Declaration of Conformity for more details.

EMU25190

Key number

If a main key switch is equipped with the motor, the key identification number is stamped on your key as shown in the illustration. Record this number in the space provided for reference in case you need a new key.

ZMU02342

Page 7

ZMU01696

EMU25221

Emission control information

EMU25351

SAV models

Engines affixed with the label pictured below conform to SAV (the Swiss exhaust emission regulations for Swiss inshore waters).

Approval label of emission control certificate

General information

Fuel requirement label

1. Fuel requirement label location

ZMU04875

ZMU04494

ZMU05253

YAMAHA MOTOR CO.,LTD.

Motorfamilie

AbgastypenprufNummer

ZMU04492

Page 8

General information

EMU33520

Read manuals and labels

Before operating or working on this motor:

●

Read this manual.

●

Read any manuals supplied with the boat.

●

Read all labels on the outboard motor and the boat.

If you need any additional information, contact your Yamaha dealer.

EMU33830

Warning labels

If these labels are damaged or missing, contact your Yamaha dealer for replacements.

ZMU05703

Page 9

General information

EMU33911

Contents of labels

The above warning labels mean as follows.

EWM01690

WARNING

Emergency starting does not have startin-gear protection. Ensure shift control is in neutral before starting engine.

EWM01680

WARNING

●

Keep hands, hair, and clothing away from rotating parts while the engine is running.

●

Do not touch or remove electrical parts when starting or during operation.

ZMU05706

EWM01670

WARNING

●

Read Owner’s Manuals and labels.

●

Wear an approved personal flotation device (PFD).

●

Attach engine shut-off cord (lanyard) to your PFD, arm, or leg so the engine stops if you accidentally leave the helm, which could prevent a runaway boat.

EMU33841

Symbols

The following symbols mean as follows.

Caution/Warning

Page 10

General information

ZMU05696

Read Operator’s Manual

ZMU05664

Hazard caused by continuous rotation

ZMU05665

Electrical hazard

ZMU05666

Remote control lever/gear shift lever operating direction, dual direction

ZMU05667

Engine start/ Engine cranking

ZMU05668

Page 11

Safety information

EMU33620

Safety information

Observe these precautions at all times.

EMU33630

Rotating parts

Hands, feet, hair, jewelry, clothing, PFD straps, etc. can become entangled with internal rotating parts of the engine, resulting in serious injury or death. Keep the top cowling in place whenever possible. Do not remove or replace the cowling with the engine running. Only operate the engine with the cowling removed according to the specific instructions in the manual. Keep hands, feet, hair, jewelry, clothing, PFD straps, etc. away from any exposed moving parts.

EMU33640

Hot parts

During and after operation, engine parts are hot enough to cause burns. Avoid touching any parts under the top cowling until the engine has cooled.

EMU33650

Electric shock

Do not touch any electrical parts while starting or operating the engine. They can cause shock or electrocution.

EMU33670

Engine shut-off cord

Attach the engine shut-off cord so that the engine stops if the operator falls overboard or leaves the helm. This prevents the boat from running away under power and leaving people stranded, or running over people or objects. Always attach the engine shut-off cord to a secure place on your clothing or your arm or leg while operating. Do not remove it to leave the helm while the boat is moving. Do not attach the cord to clothing that could tear loose, or route the cord where it could be-

come entangled, preventing it from functioning. Do not route the cord where it is likely to be accidentally pulled out. If the cord is pulled during operation, the engine will shut off and you will lose most steering control. The boat could slow rapidly, throwing people and objects forward.

EMU33810

Gasoline

Gasoline and its vapors are highly flammable and explosive.

Always, refuel according to the procedure on page 27 to reduce the risk of fire and explosion.

EMU33820

Gasoline exposure and spills

Take care not to spill gasoline. If gasoline spills, wipe it up immediately with dry rags. Dispose of rags properly. If any gasoline spills onto your skin, immediately wash with soap and water. Change clothing if gasoline spills on it. If you swallow gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention. Never siphon fuel by mouth.

EMU33900

Carbon monoxide

This product emits exhaust gases which contain carbon monoxide, a colorless, odorless gas which may cause brain damage or death when inhaled. Symptoms include nausea, dizziness, and drowsiness. Keep cockpit and cabin areas well ventilated. Avoid blocking exhaust outlets.

EMU33780

Modifications

Do not attempt to modify this outboard motor. Modifications to your outboard motor may reduce safety and reliability, and render the outboard unsafe or illegal to use.

Page 12

Safety information

EMU33740

Boating safety

This section includes a few of the many important safety precautions that you should follow when boating.

EMU33710

Alcohol and drugs

Never operate after drinking alcohol or taking drugs. Intoxication is one of the most common factors contributing to boating fatalities.

EMU33720

Personal flotation devices

Have an approved personal flotation device (PFD) on board for every occupant. Yamaha recommends that you must wear a PFD whenever boating. At a minimum, children and non-swimmers should always wear PFDs, and everyone should wear PFDs when there are potentially hazardous boating conditions.

EMU33730

People in the water

Always watch carefully for people in the water, such as swimmers, skiers, or divers, whenever the engine is running. When someone is in the water near the boat, shift into neutral and shut off the motor. Stay away from swimming areas. Swimmers can be hard to see. The propeller can keep moving even when the motor is in neutral. Shut off the engine when a person is in the water near you.

EMU33750

Passengers

Consult your boat manufacturer’s instructions for details about appropriate passenger locations in your boat and be sure all passengers are positioned properly before accelerating and when operating above an idle speed. Standing or sitting in non-designated locations may result in being thrown either

overboard or within the boat due to waves, wakes, or sudden changes in speed or direction. Even when people are positioned properly, alert your passengers if you must make any unusual maneuver. Always avoid jumping waves or wakes.

EMU33760

Overloading

Do not overload the boat. Consult the boat capacity plate or boat manufacturer for maximum weight and number of passengers. Be sure that weight is properly distributed according to the boat manufacturers instructions. Overloading or incorrect weight distribution can compromise the boats handling and lead to an accident, capsizing or swamping.

EMU33770

Avoid collisions

Scan constantly

other boats. Be alert for conditions that limit your visibility or block your vision of others.

Operate defensively

keep a safe distance away from people, objects, and other boats.

Do not follow directly behind other boats or

●

waterskiers.

●

Avoid sharp turns or other maneuvers that make it hard for others to avoid you or understand where you are going.

●

Avoid areas with submerged objects or shallow water.

●

Ride within your limits and avoid aggressive maneuvers to reduce the risk of loss of control, ejection, and collision.

●

Take early action

member, stopping the engine or reducing throttle can reduce the ability to steer. If you are not sure that you can stop in time before hitting an obstacle, apply throttle and turn in another direction.

for people, objects, and

at safe speeds and

to avoid collisions. Re-

boats do not have brakes

, and

Page 13

EMU33790

Weather

Stay informed about the weather. Check weather forecasts before boating. Avoid boating in hazardous weather.

EMU33880

Passenger training

Make sure at least one other passenger is trained to operate the boat in the event of an emergency.

EMU33890

Boating safety publications

Be informed about boating safety. Additional publications and information can be obtained from many boating organizations.

EMU33600

Laws and regulations

Know the marine laws and regulations where you will be boating- and obey them. Several sets of rules prevail according to geographic location, but all are basically the same as the International Rules of the Road.

Safety information

Page 14

Basic requirements

EMU25540

Fueling instructions

EWM00010

WARNING

GASOLINE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE!

●

Do not smoke when refueling, and keep away from sparks, flames, or other sources of ignition.

●

Stop engine before refueling.

●

Refuel in a well-ventilated area. Refuel portable fuel tanks off the boat.

●

Take care not to spill gasoline. If gasoline spills, wipe it up immediately with dry rags.

●

Do not overfill the fuel tank.

●

Tighten the filler cap securely after refueling.

●

If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention.

●

If any gasoline spills onto your skin, immediately wash with soap and water. Change clothing if gasoline spills on it.

●

Touch the fuel nozzle to the filler opening or funnel to help prevent electrostatic sparks.

ECM00010

CAUTION:

Use only new clean gasoline which has been stored in clean containers and is not contaminated with water or foreign matter.

EMU25580

Gasoline

Recommended gasoline:

Regular unleaded gasoline with a minimum octane rating of 90 (Research Octane Number).

If knocking or pinging occurs, use a different brand of gasoline or premium unleaded fuel.

EMU25683

Engine oil

Recommended engine oil:

4-stroke motor oil with a combination of the following SAE and API oil classifications

Engine oil type SAE:

10W-30 or 10W-40

Engine oil grade API:

SE, SF, SG, SH, SJ, SL

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

NOTE:

If the recommended engine oil grades are not available, select an alternative from the following chart according to the average temperatures in your area.

Page 15

ECM01050

CAUTION:

All 4-stroke engines are shipped from the factory without engine oil.

Basic requirements

instability.

EMU33570

Mounting motor

Your dealer or other person experienced in proper rigging should mount the motor using correct equipment and complete rigging instructions. For further information, see page

23.

EWM01570

WARNING

●

Improper mounting of the outboard motor could result in hazardous conditions such as poor handling, loss of control, or fire hazards.

●

Because the motor is very heavy, special equipment and training is required to mount it safely.

EMU25692

Battery requirement

ECM01061

CAUTION:

Do not use a battery that does not meet the specified capacity. If a battery that does not meet specifications is used, the electric system could perform poorly or be overloaded, causing electric system damage.

ZMU01710

EMU33550

Installation requirements

EMU33560

Boat horsepower rating

Before installing the outboard motor(s), confirm that the total horsepower of your motor(s) does not exceed the boats maximum horsepower rating. See the boats capacity plate or contact the manufacturer.

EWM01560

WARNING

Overpowering a boat can cause severe

For electric start models, choose a battery which meets the following specifications.

EMU25721

Battery specifications

Minimum cold cranking amps (CCA/EN):

F9.9CE 347.0 A FT9.9DE 347.0 A

Minimum rated capacity (20HR/IEC):

F9.9CE 40.0 Ah FT9.9DE 40.0 Ah

The engine cannot be started if battery voltage is too low.

Page 16

Basic requirements

EMU34190

Propeller selection

Next to selecting an outboard, choosing the right propeller is one of the most important purchasing decisions a boater can make. The type, size, and design of your propeller have a direct impact on acceleration, top speed, fuel economy, and even engine life. Yamaha designs and manufactures propellers for every Yamaha outboard motor and every application. Your outboard motor came with a Yamaha propeller chosen to perform well over a range of applications, but there may be uses where a different propeller would be more appropriate. Your Yamaha dealer can help you select the right propeller for your boating needs. Select a propeller that will allow the engine to reach the middle or upper half of the operating range at full throttle with the maximum boatload. Generally, chose a larger pitch propeller for a smaller operating load and a smaller pitch propeller for a heavier load. If you carry loads that vary widely, chose the propeller that lets the engine run in the proper range for your maximum load but remember that you may need to reduce your throttle setting to stay within the recommended engine speed range when carrying lighter loads. For instructions on propeller removal and installation, see page 59.

123

ZMU04605

1. Propeller diameter in inches

2. Propeller pitch in inches

3. Type of propeller (propeller mark)

123

ZMU04604

1. Propeller diameter in inches

2. Propeller pitch in inches

3. Type of propeller (propeller mark)

EMU25770

Start-in-gear protection

Yamaha outboard motors or Yamaha-approved remote control units are equipped with start-in-gear protection device(s). This feature permits the engine to be started only when it is in neutral. Always select neutral before starting the engine.

Page 17

Basic components

EMU2579B

Main components

NOTE:

* May not be exactly as shown; also may not be included as standard equipment on all models.

F9.9C, F15A

9 8 7

1. Top cowling

2. Top cowling lock lever(s)

3. Drain screw

4. Anti-cavitation plate

5. Propeller

6. Cooling water inlet

7. Trim rod*

8. Clamp bracket

9. Steering friction adjuster

10. Manual starter handle*

11. Choke knob

12. Warning indicator(s)

13. Gear shift lever*

14. Tiller handle*

15. Engine stop button/Engine shut-off switch*

16. Transom clamp handle

17. Rope attachment

18. Tilt lock lever*

19. Flushing device*

20. Remote control box (side mount type)*

21. Fuel tank

22. Clip

ZMU04892

Page 18

Basic components

FT9.9D

4 5

1. Top cowling

2. Top cowling lock lever(s)

3. Drain screw

4. Anti-cavitation plate

5. Propeller

6. Cooling water inlet

7. Trim rod*

8. Steering friction adjuster

9. Clamp bracket

10. Tiller handle*

11. Choke knob

12. Manual starter handle*

13. Warning indicator

14. Throttle friction adjuster*

15. Engine stop button/Engine shut-off switch*

16. Transom clamp handle

17. Rope attachment

18. Tilt lock lever*

19. Flushing device

20. Remote control box (side mount type)*

21. Fuel tank

20 21

ZMU04891

22. Clip

EMU25802

Fuel tank

If your model was equipped with a portable fuel tank, its function is as follows.

EWM00020

WARNING

The fuel tank supplied with this engine is its dedicated fuel reservoir and must not be used as a fuel storage container. Commercial users should conform to relevant licensing or approval authority regulations.

Page 19

Basic components

1. Air vent screw

2. Fuel gauge

3. Fuel joint

4. Fuel tank cap

EMU25830

ZMU01992

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank cap or on the fuel joint base. It shows the approximate amount of fuel remaining in the tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed, the tank can be filled with fuel. To remove the cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen the screw, turn it counterclockwise.

EMU26180

Remote control

The remote control lever actuates both the shifter and the throttle. The electrical switches are mounted on the remote control box.

1. Remote control lever

2. Neutral interlock trigger

3. Neutral throttle lever

4. Main switch / choke switch

5. Engine shut-off switch

6. Throttle friction adjuster

EMU26190

Remote control lever

Moving the lever forward from the neutral position engages forward gear. Pulling the lever back from neutral engages reverse. The engine will continue to run at idle until the lever is moved about 35° (a detent can be felt). Moving the lever farther opens the throttle, and the engine will begin to accelerate.

1. Neutral “”

2. Forward “”

3. Reverse “”

4. Shift

5. Fully closed

6. Throttle

Page 20

Basic components

7. Fully open

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral interlock trigger up.

1. Neutral interlock trigger

EMU26211

Neutral throttle lever

To open the throttle without shifting into either forward or reverse, put the remote control lever in the neutral position and lift the neutral throttle lever.

NOTE:

The neutral throttle lever will operate only when the remote control lever is in neutral. The remote control lever will operate only when the neutral throttle lever is in the closed position.

2. Fully closed

EMU26221

Choke switch

To activate the choke system, press in the main switch while the key is turned to the “” (on) or “” (start) position. The choke system will then supply the rich fuel mixture required to start the engine. When the key is released, the choke will switch off automatically.

ZMU03160

EMU25911

Tiller handle

To change direction, move the tiller handle to the left or right as necessary.

1. Fully open

ZMU01997

Page 21

Basic components

ZMU04879

EMU25922

Gear shift lever

Pulling the gear shift lever towards you puts the engine in forward gear so that the boat moves ahead. Pushing the lever away from you puts the engine in reverse gear so that the boat moves astern.

ZMU04878

1. Forward “”

2. Neutral “”

3. Reverse “”

EMU25941

Throttle grip

The throttle grip is on the tiller handle. Turn the grip counterclockwise to increase speed and clockwise to decrease speed.

1. Forward “”

2. Neutral “”

3. Reverse “”

ZMU01998

ZMU01999

EMU25961

Throttle indicator

The fuel consumption curve on the throttle indicator shows the relative amount of fuel consumed for each throttle position. Choose the setting that offers the best performance and fuel economy for the desired operation.

Page 22

Basic components

ZMU02000

1. Throttle indicator

EMU25971

Throttle friction adjuster

A friction device provides adjustable resistance to movement of the throttle grip or the remote control lever, and can be set according to operator preference. To increase resistance, turn the adjuster clockwise. To decrease resistance, turn the adjuster counterclockwise.

EWM00031

WARNING

Do not overtighten the friction adjuster. If there is too much resistance, it could be difficult to move the remote control lever or throttle grip, which could result in an accident.

ZMU02001

When constant speed is desired, tighten the adjuster to maintain the desired throttle setting.

EMU25991

Engine shut-off switch

The clip must be attached to the engine shutoff switch for the engine to run. The cord should be attached to a secure place on the operator’s clothing, or arm or leg. Should the operator fall overboard or leave the helm, the cord will pull out the clip, stopping ignition to the engine. This will prevent the boat from running away under power.

EWM00121

WARNING

●

Attach the engine shut-off cord to a secure place on your clothing, or your arm or leg while operating.

●

Do not attach the cord to clothing that could tear loose. Do not route the cord where it could become entangled, preventing it from functioning. Avoid accidentally pulling the cord dur-

●

ing normal operation. Loss of engine power means the loss of most steering control. Also, without engine power, the boat could slow rapidly. This could cause people and objects in the boat to be thrown forward.

NOTE:

The engine cannot be started with the clip re-

Page 23

Basic components

moved.

1. Cord

2. Clip

EMU26011

Choke knob for pull type

To supply the engine with the rich fuel mixture required to start, pull out this knob.

ZMU02003

ZMU02355

EMU26070

Manual starter handle

To start the engine, first gently pull the handle out until resistance is felt. From that position, then pull the handle straight out quickly to crank the engine.

1. Cord

2. Clip

EMU26001

Engine stop button

To open the ignition circuit and stop the engine, push this button.

ZMU02083

ZMU02005

EMU26080

Starter button

To start the engine with the electric starter, push the starter button.

Page 24

Basic components

ZMU04880

EMU26090

Main switch

The main switch controls the ignition system; its operation is described below.

●

“”

(off)

With the main switch in the “” (off) posi- tion, the electrical circuits are off, and the key can be removed.

●

“”

(on)

With the main switch in the “” (on) posi- tion, the electrical circuits are on, and the key cannot be removed.

●

“” With the main switch in the “” (start) po- sition, the starter motor turns to start the engine. When the key is released, it returns automatically to the “” (on) position.

(start)

set according to operator preference. An adjuster lever is located on the bottom of the tiller handle bracket. To increase resistance, turn the lever to the port side “A”. To decrease resistance, turn the lever to the starboard side “B”.

EWM00040

WARNING

Do not overtighten the friction adjuster. If there is too much resistance, it could be difficult to steer, which could result in an accident.

If the resistance does not increase even when the lever is turned to the port side “A”, make sure that the nut is tightened to the specified torque.

ZMU02340

EMU31432

Steering friction adjuster

A friction device provides adjustable resistance to the steering mechanism, and can be

1. Nut

Page 25

Basic components

Nut tightening torque:

3.9 Nm (2.9 ft-lb) (0.4 kgf-m)

NOTE:

●

Steering movement is blocked when the

adjuster lever is set to the “A” position.

●

Check the tiller handle for smooth move-

ment when the lever is turned to the star-

board side “B”.

●

Do not apply lubricants such as grease to

the friction areas of the steering friction ad-

juster.

EMU26122

Steering friction adjuster

A friction device provides adjustable resistance to the steering mechanism, and can be set according to operator preference. An adjusting screw or bolt is located on the swivel bracket.

EMU26261

Trim rod (tilt pin)

The position of the trim rod determines the minimum trim angle of the outboard motor in relation to the transom.

ZMU02007

EMU26312

Tilt lock mechanism

The tilt lock mechanism is used to prevent the outboard motor from lifting out of the water when in reverse gear.

ZMU02080

To increase resistance, turn the adjuster clockwise. To decrease resistance, turn the adjuster counterclockwise.

EWM00040

WARNING

Do not overtighten the friction adjuster. If there is too much resistance, it could be difficult to steer, which could result in an accident.

ZMU02008

1. Tilt lock lever

To lock it, set the tilt lock lever in the “” (lock) position. To release, push the tilt lock lever in the “” (release) position.

EMU26332

Tilt support bar

The tilt support bar keeps the outboard motor in the tilted up position.

Page 26

Basic components

ZMU02078

ECM01660

CAUTION:

Do not use the tilt support bar when trailering the boat. The outboard motor could shake loose from the tilt support and fall. If the motor cannot be trailered in the normal running position, use an additional support device to secure it in the tilt position.

EMU26372

Top cowling lock lever(s) (turn type)

To remove the engine top cowling, turn the lock lever(s) and lift off the cowling. When installing the cowling, check to be sure it fits properly in the rubber seal. Then lock the cowling again by returning the lever(s) to the lock position.

EMU26460

Flushing device

This device is used to clean the cooling water passages of the motor using a garden hose and tap water.

NOTE:

For details on usage, see page 46.

ZMU04885

1. Flushing device

EMU26302

Warning indicator

If the engine develops a condition which is cause for warning, the indicator lights up. For details on how to read the warning indicator, see page 21.

1. Top cowling lock lever(s)

ZMU02009

ZMU02010

EMU26801

Warning system

ECM00090

CAUTION:

Do not continue to operate the engine if a warning device has activated. Consult

Page 27

Basic components

your Yamaha dealer if the problem cannot be located and corrected.

EMU30168

Low oil pressure warning

If the oil pressure drops too low, the warning device will activate.

Activation of warning device

●

The engine speed will automatically de-

crease to about 2000 r/min.

●

If equipped with a low oil pressure-warning

indicator, it will light or blink.

ZMU02081

●

The buzzer will sound (if equipped on the

tiller handle, remote control box, or main

switch panel).

not switch off, consult your Yamaha dealer.

ECM00101

CAUTION:

Do not continue to run the engine if the low oil pressure-warning indicator is on. Serious engine damage could occur.

ZMU02360

If the warning system has activated, stop the engine as soon as it is safe to do so. Check the oil level and add oil as needed. If the oil level is correct and the warning device does

Page 28

Operation

EMU26902

Installation

The information presented in this section is intended as reference only. It is not possible to provide complete instructions for every possible boat and motor combination. Proper mounting depends in part on experience and the specific boat and motor combination.

EWM01590

WARNING

●

Overpowering a boat could cause se-

vere instability. Do not install an out-

board motor with more horsepower

than the maximum rating on the capac-

ity plate of the boat. If the boat does not

have a capacity plate, consult the boat

manufacturer.

●

Improper mounting of the outboard mo-

tor could result in hazardous condi-

tions such as poor handling, loss of

control, or fire hazards. For permanent-

ly mounted models, your dealer or oth-

er person experienced in proper

rigging should mount the motor.

EMU26911

Mounting the outboard motor

EWM01720

WARNING

Your dealer or other person experienced in proper outboard motor mounting should show you how to mount your outboard motor.

1. Center line (keel line)

EMU26921

ZMU01760

Mounting height

To run your boat at optimum efficiency, the water resistance (drag) of the boat and outboard motor must be made as little as possible. The mounting height of the outboard motor greatly affects the water resistance. If the mounting height is too high, cavitation tends to occur, thus reducing the propulsion; and if the propeller tips cut the air, the engine speed will rise abnormally and cause the engine to overheat. If the mounting height is too low, the water resistance will increase and thereby reduce engine efficiency. Mount the outboard motor so that the anti-cavitation plate is between the bottom of the boat and a level 25 mm (1 in.) below it.

The outboard motor should be mounted so that the boat is well balanced. Otherwise, the boat could be hard to steer. For single-engine boats, mount the outboard motor on the centerline (keel line) of the boat.

Page 29

0–25mm (0–1in.)

ECM01630

ZMU02011

CAUTION:

During water testing, check the buoy-

●

ancy of the boat, at rest, with its maxi-

mum load. Check that the static water

level on the exhaust housing is low

enough to prevent water entry into the

power head when water rises due to

waves when the outboard is not run-

ning.

Incorrect engine height or obstructions

●

to the smooth flow of water (such as the

design or condition of the boat, or ac-

cessories such as transom ladders or

depth finder transducers) can create

airborne water spray while the boat is

cruising. If the motor is operated con-

tinuously in the presence of airborne

water spray, enough water could enter

the engine through the intake opening

on the cowling to cause severe engine

damage. Eliminate the cause of the air-

borne water spray.

Operation

ufacturer for further information on determining the proper mounting height. For instructions on setting the trim angle of

●

the outboard motor, see page 35.

EMU26970

Clamping the outboard motor

1. Place the outboard motor on the transom so that it is positioned as close to the center as possible. Tighten the transom clamp screws evenly and securely. Occasionally check the clamp screws for tightness during operation of the outboard motor because they could become loose due to engine vibration.

EWM00640

WARNING

Loose clamp screws could allow the outboard motor to fall off or move on the transom. This could cause loss of control and serious injury. Make sure the transom screws are tightened securely. Occasionally check the screws for tightness during operation.

ZMU02012

NOTE:

●

The optimum mounting height of the outboard motor is affected by the boat and motor combination and the desired use. Test runs at different heights can help determine the optimum mounting height. Consult your Yamaha dealer or boat man-

2. If the engine restraint cable attachment is equipped on your engine, an engine restraint cable or chain should be used. Attach one end to the engine restraint cable attachment and the other to a secure mounting point on the boat. Otherwise the engine could be completely lost

Page 30

Operation

if it accidentally falls off the transom.

ZMU02013

3. Secure the clamp bracket to the transom using the bolts provided with the outboard (if packed). For details, consult your Yamaha dealer.

EWM00650

WARNING

Avoid using bolts, nuts or washers other than those contained in the engine packaging. If used, they must be of at least the same quality of material and strength and must be tightened securely. After tightening, test run the engine and check their tightness.

ZMU02631

1. Bolts

EMU30173

Breaking in engine

Your new engine requires a period of breakin to allow mating surfaces of moving parts to

wear in evenly. Correct break-in will help ensure proper performance and longer engine life.

ECM00800

CAUTION:

Failure to follow the break-in procedure could result in reduced engine life or even severe engine damage.

EMU27083

Procedure for 4-stroke models

Your new engine requires a period of tenhours break-in to allow mating surfaces of moving parts to wear in evenly. Correct break-in will help ensure proper performance and longer engine life.

NOTE:

Failure to follow the break-in procedure could result in reduced engine life or even severe engine damage. Run the engine in the water, under load (in gear with a propeller installed) as follows. For ten hours for breaking in engine avoid extended idling, rough water and crowded areas.

1. For the first hour of operation: Run the engine at varying speeds up to 2000 r/min or approximately half throttle.

2. For the second hour of operation: Increase engine speed as much as necessary to put the boat on plane (but avoid full-throttle operation), then back off on the throttle while keeping the boat at a planing speed.

3. Remaining eight hours: Run the engine at any speed. However, avoid operating at full throttle for more than 5 minutes at a time.

4. After the first 10 hours: Operate the engine normally.

Page 31

Operation

EMU27104

Pre-operation checks

EWM00081

WARNING

If any item in the pre-operation check is not working properly, have it inspected and repaired before operating the outboard motor. Otherwise an accident could occur.

ECM00120

CAUTION:

Do not start the engine out of water. Overheating and serious engine damage can occur.

EMU27111

Fuel

Check to be sure you have plenty of fuel

●

for your trip. Make sure there are no fuel leaks or gaso-

●

line fumes.

●

Check fuel line connections to be sure they are tight (if equipped Yamaha fuel tank or boat tank).

●

Be sure the fuel tank is positioned on a secure, flat surface, and that the fuel line is not twisted or flattened, or likely to contact sharp objects (if equipped Yamaha fuel tank or boat tank).

EMU27130

Controls

●

Check throttle, shift, and steering for proper operation before starting the engine. The controls should work smoothly, with-

●

out binding or unusual free play.

●

Look for loose or damaged connections. Check operation of the starter and stop

●

switches when the outboard motor is in the water.

EMU31721

Stop switches

●

Confirm that turning the main switch to the

“” (off) position stops the engine.

●

Confirm that removing the clip from the engine shut-off switch stops the engine.

●

Confirm that the engine cannot be started with the clip removed from the engine shut-off switch.

EMU27140

Engine

●

Check the engine and engine mounting. Look for loose or damaged fasteners.

●

Check the propeller for damage.

EMU27163

Checking the engine oil level

1. Put the outboard motor in an upright position (not tilted).

2. Remove oil dipstick and wipe it clean.

3. Completely insert the dipstick and remove it again.

4. Check the oil level using the dipstick to be sure the level falls between the upper and lower marks. Fill with oil if it is below the lower mark, or drain to the specified level if it is above the upper mark.

ZMU02082

1. Lower level mark

2. Oil dipstick

3. Upper level mark

NOTE:

Be sure to completely insert the dipstick into the dipstick guide.

Page 32

Operation

EMU27441

Filling fuel

EWM00060

WARNING

Gasoline and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames, or other sources of ignition.

1. Remove the fuel tank cap.

2. Fill the fuel tank carefully.

3. Close the cap securely after refueling. Wipe up any spilled fuel.

Fuel tank capacity:

12 L (3.17 US gal) (2.64 Imp.gal)

NOTE:

The smaller fuel filling hole on the fuel tank has been designed to fit unleaded fuel fillers only for emission control models (for Bodensee).

EMU27450

Operating engine

EMU27463

Feeding fuel (portable tank)

EWM00420

WARNING

Before starting the engine, make sure

●

that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the water near you. When the air vent screw is loosened,

●

gasoline vapor will be released. Gasoline is highly flammable, and its vapors are flammable and explosive. Refrain from smoking, and keep away from open flames and sparks while loosening the air vent screw. This product emits exhaust gases

●

which contain carbon monoxide, a col-

orless, odorless gas which could cause brain damage or death when inhaled. Symptoms include nausea, dizziness, and drowsiness. Keep cockpit and cabin areas well ventilated. Avoid blocking exhaust outlets.

1. If there is an air vent screw on the fuel tank cap, loosen it 2 or 3 turns.

2. If there is a fuel joint on the motor, firmly connect the fuel line to the joint. Then firmly connect the other end of the fuel line to the joint on the fuel tank.

ZMU02024

Page 33

ZMU02023

3. If a steering friction adjuster is provided on your outboard motor, securely attach the fuel line to the fuel line clamp.

NOTE:

During engine operation place the tank horizontally, otherwise fuel cannot be drawn from the fuel tank.

4. Squeeze the primer pump, with the arrow pointing up, until you feel it become firm.

Operation

ter near you.

EMU27506

Manual start models (tiller control)

1. Place the gear shift lever in neutral.

ZMU01988

1. Arrow

EMU27491

Starting engine

EWM01600

WARNING

Before starting the engine, make sure that the boat is tightly moored and that you can steer clear of any obstructions. Be sure there are no swimmers in the wa-

ZMU04881

NOTE:

The start-in-gear protection device prevents the engine from starting except when in neutral.

2. Attach the engine shut-off cord to a secure place on your clothing, or your arm or leg. Then install the clip on the other end of the cord into the engine shut-off switch.

EWM00121

WARNING

●

Attach the engine shut-off cord to a secure place on your clothing, or your arm or leg while operating.

●

Do not attach the cord to clothing that could tear loose. Do not route the cord

Page 34

Operation

where it could become entangled, preventing it from functioning. Avoid accidentally pulling the cord dur-

●

NOTE:

●

5. Pull the manual starter handle slowly un-

ZMU02026

3. Place the throttle grip in the “” (start) position.

ZMU02355

It is not necessary to use the choke when starting a warm engine. If the choke knob is left in the “” (start) position while the engine is running, the engine will run poorly or stall.

til you feel resistance. Then give a strong pull straight out to crank and start the engine. Repeat if necessary.

ZMU02027

4. Pull out / turn the choke knob fully. After the engine starts, replace / return the knob to the home position.

ZMU02029

6. After the engine starts, slowly return the manual starter handle to its original position before releasing it.

7. Slowly return the throttle grip to the fully closed position.

Page 35

ZMU02030

NOTE:

When the engine is cold, it needs to be

●

warmed up. For further information, see page 32. If the engine does not start on the first try,

●

repeat the procedure. If the engine fails to start after 4 or 5 tries, open the throttle a small amount (between 1/8 and 1/4) and try again. Also if the engine is warm and fails to start, open the throttle a same amount and try to start the engine again. If the engine still fails to start, see page 66.

EMU27643

Electric start / remote control models

1. Place the remote control lever in neutral.

Operation

cure place on your clothing, or your arm or leg. Then install the clip on the other end of the cord into the engine shut-off switch.

EWM00121

WARNING

Attach the engine shut-off cord to a se-

●

cure place on your clothing, or your arm or leg while operating. Do not attach the cord to clothing that

●

could tear loose. Do not route the cord where it could become entangled, preventing it from functioning.

●

Avoid accidentally pulling the cord during normal operation. Loss of engine power means the loss of most steering control. Also, without engine power, the boat could slow rapidly. This could cause people and objects in the boat to be thrown forward.

NOTE:

The start-in-gear protection device prevents the engine from starting except when in neutral.

2. Attach the engine shut-off cord to a se-

3. Turn the main switch to “” (on).

OFF

ZMU01880

Page 36

Operation

4. Open the throttle slightly without shifting using the neutral throttle lever or free accelerator. You may need to change the throttle opening slightly depending on engine temperature. After the engine starts, return the throttle to the original position.

STARTOFF

ZMU02314

NOTE:

●

On remote controls equipped with a neutral throttle lever, a good starting point is to lift the lever just until you feel resistance, then lift slightly more.

●

The neutral throttle lever or free accelerator can only be used when the remote control lever is in neutral.

5. Press in and hold the main switch to operate the remote choke system. The remote choke switch automatically returns to its normal position when you release your hand. Therefore keep the switch pressed in.

ZMU02315

NOTE:

It is not necessary to use the choke when

●

starting a warm engine. Push in the main switch fully, or the remote

●

choke system will not operate.

6. Turn the main switch to “” (start), and hold it for a maximum of 5 seconds.

7. Immediately after the engine starts, release the main switch and allow it to return to “” (on).

ECM00191

CAUTION:

●

Never turn the main switch to “” (start) while the engine is running. Do not keep the starter motor turning

●

for more than 5 seconds. If the starter motor is turned continuously for more than 5 seconds, the battery will be quickly discharged, thus making it impossible to start the engine. The starter

Page 37

can also be damaged. If the engine will not start after 5 seconds of cranking, return the main switch to “” (on), wait 10 seconds, then crank the engine again.

EMU27670

Warming up engine

EMU27710

Manual start and electric start models

1. After starting the engine, allow it to idle for 3 minutes to warm up. Failure to do so will shorten engine life.

2. Be sure the low oil pressure warning indicator goes off after starting the engine.

3. Check for a steady flow of water from the cooling water pilot hole.

ECM00210

CAUTION:

●

If the low oil pressure warning indicator does not go off after the engine starts, stop the engine. Otherwise serious engine damage could occur. Check the oil level and add oil if necessary. Consult your Yamaha dealer if the cause for the low oil pressure warning indicator cannot be found.

●

A continuous flow of water from the pilot hole shows that the water pump is pumping water through the cooling passages. If water is not flowing out of the pilot hole at all times while the engine is running, overheating and serious damage could occur. Stop the engine and check whether the cooling water inlet on the lower case or the cooling water pilot hole is blocked. Consult your Yamaha dealer if the problem cannot be located and corrected.

Operation

ZMU02034

EMU34530

Shifting

EWM00180

WARNING

Before shifting, make sure there are no swimmers or obstacles in the water near you.

ECM01610

CAUTION:

Warm up the engine before shifting into gear. Until the engine is warm, the idle speed may be higher than normal. High idle speed can prevent you from shifting back to neutral. If this occurs, stop the engine, shift to neutral, then restart the engine and allow it to warm up.

To shift out of neutral

1. Pull the neutral interlock trigger up (if equipped).

1. Neutral interlock trigger

Page 38

Operation

2. Move the remote control lever / gear shift lever firmly and crisply forward (for forward gear) or backward (for reverse gear) [about 35° (a detent can felt) for remote control models]. Be sure to check that the tilt lock lever is in the lock/down position (if equipped) before operating in reverse.

ZMU02086

ZMU05749

To shift from in gear (forward/reverse) to neutral

1. Close the throttle so that the engine slows to idle speed.

ZMU02030

2. After the engine is at idle speed in gear move the remote control lever / gear

ZMU05694

shift lever firmly and crisply into the neutral position.

Page 39

Operation

shift mechanism.

●

Do not shift into reverse while traveling at planing speeds. Loss of control, boat swamping, or damage to the boat could occur.

The boat is not equipped with a separate braking system. Water resistance stops it after the throttle lever is moved back to idle. The stopping distance varies depending on gross weight, water surface conditions, and wind direction.

ZMU05695

EMU27820

Stopping engine

Before stopping the engine, first let it cool off for a few minutes at idle or low speed. Stopping the engine immediately after operating at high speed is not recommended.

EMU27845

Procedure

1. Push and hold the engine stop button or turn the main switch to “” (off).

ZMU04881

EMU31742

Stopping boat

EWM01510

WARNING

●

Do not use the reverse function to slow down or stop the boat as it could cause you to lose control, be ejected, or impact the steering wheel or other parts of the boat. This could increase the risk of serious injury. It could also damage the

ZMU02083

Page 40

Operation

2. After stopping the engine, disconnect the fuel line if there is a fuel joint on the outboard motor.

ZMU02042

3. Tighten the air vent screw on the fuel tank cap (if equipped).

ZMU05041

boat, engine, and propeller. Correct trim is also affected by variables such as the load in the boat, sea conditions, and running speed.

EWM00740

WARNING

Excessive trim for the operating conditions (either trim up or trim down) can cause boat instability and can make steering the boat more difficult. This increases the possibility of an accident. If the boat begins to feel unstable or is hard to steer, slow down and/or readjust the trim angle.

4. Remove the key if the boat will be left unattended.

NOTE:

The engine can also be stopped by pulling the cord and removing the clip from the engine shut-off switch, then turning the main switch to “” (off).

EMU27861

Trimming outboard motor

The trim angle of the outboard motor helps determine the position of the bow of the boat in the water. Correct trim angle will help improve performance and fuel economy while reducing strain on the engine. Correct trim angle depends upon the combination of

ZMU02043

1. Trim operating angle

EMU27872

Adjusting trim angle for manual tilt models

There are 4 or 5 holes provided in the clamp bracket to adjust the outboard motor trim angle.

Page 41

Operation

1. Stop the engine.

2. Tilt the outboard motor up, and then remove the trim rod from the clamp bracket.

ZMU02007

3. Reposition the rod in the desired hole.

To raise the bow (“trim-out”), move the rod away from the transom. To lower the bow (“trim-in”), move the rod toward the transom. Make test runs with the trim set to different angles to find the position that works best for your boat and operating conditions.

EWM00400

WARNING

●

Stop the engine before adjusting the trim angle. Use care to avoid being pinched when

●

removing or installing the rod.

●

Use caution when trying a trim position for the first time. Increase speed gradually and watch for any signs of instability or control problems. Improper trim angle can cause loss of control.

results in less drag, greater stability and efficiency. This is generally when the keel line of the boat is up about 3 to 5 degrees. With the bow up, the boat may have a greater tendency to steer to one side or the other. Compensate for this as you steer. The trim tab can also be adjusted to help offset this effect. When the bow of the boat is down, it is easier to accelerate from a standing start onto plane.

Bow Up

Too much trim-out puts the bow of the boat too high in the water. Performance and economy are decreased because the hull of the boat is pushing the water and there is more air drag. Excessive trim-out can also cause the propeller to ventilate, which reduces performance further, and the boat may “por- poise” (hop in the water), which could throw the operator and passengers overboard.

NOTE:

The outboard motor trim angle can be changed approximately 4 degrees by shifting the trim rod one hole.

EMU27911

Adjusting boat trim

When the boat is on plane, a bow-up attitude

Page 42

Operation

Bow Down

Too much trim-in causes the boat to “plow” through the water, decreasing fuel economy and making it hard to increase speed. Operating with excessive trim-in at higher speeds also makes the boat unstable. Resistance at the bow is greatly increased, heightening the danger of “bow steering” and making operation difficult and dangerous.

NOTE:

Depending on the type of boat, the outboard motor trim angle may have little effect on the trim of the boat when operating.

EMU27934

Tilting up and down

If the engine will be stopped for some time or if the boat is moored in shallows, the outboard motor should be tilted up to protect the propeller and lower casing from damage by collision with obstructions, and also to reduce salt corrosion.

EWM00221

WARNING

Be sure all people are clear of the outboard motor when tilting up and down, Body parts can be crushed between the motor and the clamp bracket when the

motor is trimmed or tilted.

EWM00250

WARNING

Leaking fuel is a fire hazard. If there is a fuel joint on the outboard motor, disconnect the fuel line or close the fuel cock if the engine will be tilted for more than a few minutes. Otherwise fuel may leak.

ECM00241

CAUTION:

●

Before tilting the outboard motor, stop the engine by following the procedure on page 34. Never tilt the outboard motor while the engine is running. Severe damage from overheating can result.

●

Do not tilt up the engine by pushing the tiller handle (if equipped) because this could break the handle.

EMU27979

Procedure for tilting up (manual tilt models)

1. Place the remote control lever / gear shift lever in neutral.

ZMU01988

Page 43

Operation

ZMU04881

2. Place the tilt lock lever (if equipped) in the release/up position.

ZMU02044

3. Pull up the shallow water lever (if equipped).

4. Hold the rear of the top cowling with one hand and tilt the engine up fully.

5. Push the tilt support knob into the clamp bracket. Or the tilt support bar will turn to the lock position automatically.

ZMU02078

ECM01640

CAUTION:

Do not use the tilt support lever or knob when trailering the boat. The outboard motor could shake loose from the tilt support and fall. If the motor cannot be trailered in the normal running position, use an additional support device to secure it in the tilt position. For more detailed information, see page 43.

EMU30192

Procedure for tilting down (manual tilt models)

1. Place the tilt lock lever in the lock position.

ZMU02048

2. Slightly tilt the engine up until the tilt support bar is automatically released.

3. Slowly tilt the engine down.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially

Page 44

Operation

to allow operation in shallow water.

EMU28071

Cruising in shallow water (manual tilt models)

EWM00710

WARNING

Place the gear shift in neutral before us-

●

ing the shallow water cruising system.

●

Run the boat at the lowest possible speed when using the shallow water cruising system. The tilt lock mechanism does not work while the shallow water cruising system is being used. Hitting an underwater obstacle could cause the outboard motor to lift out of the water, resulting in loss of control. Do not rotate the outboard motor 180°

●

and operate the boat in reverse. Place the gear shift in reverse to operate the boat in reverse.

●

Use extra care when operating in reverse. Too much reverse thrust can cause the outboard motor to lift out of the water, increasing the chance of accident and personal injury. Return the outboard motor to its normal

●

position as soon as the boat is back in deeper water.

ECM00260

CAUTION:

Do not tilt the outboard motor up so that the cooling water inlet on the lower unit is above the surface of the water when setting up for and cruising in shallow water. Otherwise severe damage from overheating can result.

ZMU02047

EMU28124

Procedure

1. Place the remote control lever / gear shift lever in neutral.

ZMU01988

Page 45

Operation

ZMU04881

2. Place the tilt lock lever in the release/up position.

ZMU02044

3. Slightly tilt the outboard motor up. The tilt support bar will lock automatically, supporting the outboard motor in a partially raised position.

NOTE:

This outboard motor has 2 positions for shallow water cruising.

4. To return the outboard motor to the normal running position, place the gear shift lever in neutral, then place the tilt lock lever in the lock/down position.

ZMU02048

5. Slightly tilt the outboard motor up until the tilt support bar automatically returns to the free position.

6. Slowly lower the outboard motor to the normal position.

EMU28193

Cruising in other conditions

Cruising in salt water

After operating in salt water, flush the cooling water passages with fresh water to prevent them from becoming clogged. Also rinse the outside of the outboard motor with fresh water and, if possible, rinse the power head under the cowling.

Cruising in muddy or turbid water

Yamaha strongly recommends that you use the optional chromium-plated water pump kit (available for V4 and large engines) if you use the outboard motor in water with a lot of sediment in it, such as muddy or other turbid (cloudy) water.

Cruising in acidic water

Water in some areas can be acidic. After operating in such water, flush the cooling passages with fresh water to prevent corrosion. Also rinse the outside of the outboard motor with fresh water.

Page 46

Maintenance

EMU34520

Specifications

NOTE:

“(AL)” stated in the specification data below represents the numerical value for the aluminum propeller installed. Likewise, “(SUS)” represents the value for stainless steel propeller installed and “(PL)” for plastic propeller installed.

NOTE:

“*” means, select the engine oil referring to the chart of engine oil paragraph. For further information, see page 9.

EMU28219

Dimension:

Overall length:

F15AMH 1001 mm (39.4 in) F9.9CE 643 mm (25.3 in) F9.9CMH 1001 mm (39.4 in) FT9.9DE 643 mm (25.3 in) FT9.9DMH 1105 mm (43.5 in)

Overall width:

F15AMH 427 mm (16.8 in) F9.9CE 369 mm (14.5 in) F9.9CMH 427 mm (16.8 in) FT9.9DE 369 mm (14.5 in) FT9.9DMH 501 mm (19.7 in)

Overall height S:

F15AMH 1080 mm (42.5 in) F9.9CE 1080 mm (42.5 in) F9.9CMH 1080 mm (42.5 in)

Overall height L:

F9.9CE 1207 mm (47.5 in) F9.9CMH 1207 mm (47.5 in) FT9.9DE 1253 mm (49.3 in) FT9.9DMH 1253 mm (49.3 in)

Overall height X:

FT9.9DE 1321 mm (52.0 in)

Transom height S:

F15AMH 440 mm (17.3 in) F9.9CE 440 mm (17.3 in) F9.9CMH 440 mm (17.3 in)

Transom height L:

F9.9CE 567 mm (22.3 in) F9.9CMH 567 mm (22.3 in) FT9.9DE 567 mm (22.3 in) FT9.9DMH 567 mm (22.3 in)

Transom height X:

FT9.9DE 635 mm (25.0 in)

Weight (AL) S:

F15AMH 45.0 kg (99 lb) F9.9CE 47.0 kg (104 lb) F9.9CMH 45.0 kg (99 lb)

Weight (AL) L:

F9.9CE 49.0 kg (108 lb) F9.9CMH 47.0 kg (104 lb) FT9.9DE 50.0 kg (110 lb) FT9.9DMH 49.0 kg (108 lb)

Weight (AL) X:

FT9.9DE 51.0 kg (112 lb)

Performance:

Full throttle operating range:

4500–5500 r/min

Maximum output:

F15AMH 11.0 kW@5000 r/min (15 HP@5000 r/min) F9.9CE 7.3 kW@5000 r/min (10 HP@5000 r/min) F9.9CMH 7.3 kW@5000 r/min (10 HP@5000 r/min) FT9.9DE 7.3 kW@5000 r/min (10 HP@5000 r/min) FT9.9DMH 7.3 kW@5000 r/min (10 HP@5000 r/min)

Idling speed (in neutral):

F15AMH 950 ±50 r/min F9.9CE 950 ±50 r/min F9.9CMH 950 ±50 r/min FT9.9DE 1050 ±50 r/min FT9.9DMH 1050 ±50 r/min

Page 47

Maintenance

Engine:

Type:

4-stroke L

Displacement:

323.0 cm

Bore × stroke:

59.0 × 59.0 mm (2.32 × 2.32 in)

Ignition system:

CDI

Spark plug (NGK):

DPR6EA-9

Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)

Control system:

F15AMH Tiller F9.9CE Remote control F9.9CMH Tiller FT9.9DE Remote control FT9.9DMH Tiller

Starting system:

F15AMH Manual F9.9CE Electric F9.9CMH Manual FT9.9DE Electric FT9.9DMH Manual

Starting carburetion system:

Choke valve

Valve clearance (cold engine) IN:

0.15–0.25 mm (0.0059–0.0098 in)

Valve clearance (cold engine) EX:

0.20–0.30 mm (0.0079–0.0118 in)

Min. cold cranking amps (CCA/EN):

F9.9CE 347.0 A FT9.9DE 347.0 A

Min. rated capacity (20HR/IEC):

F9.9CE 40.0 Ah FT9.9DE 40.0 Ah

Alternator output:

F15AMH 80 W F9.9CMH 80 W

Maximum generator output:

F9.9CE 10.0 A FT9.9DE 10.0 A FT9.9DMH 10.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

F15AMH 2.08 (27/13) F9.9CE 2.08 (27/13) F9.9CMH 2.08 (27/13) FT9.9DE 2.92 (38/13) FT9.9DMH 2.92 (38/13)

Trim and tilt system:

Manual tilt

Propeller mark:

F15AMH J F9.9CE J F9.9CMH J FT9.9DE R FT9.9DMH R

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. research octane:

Fuel tank capacity:

12 L (3.17 US gal) (2.64 Imp.gal)

Recommended engine oil:

4-stroke outboard motor oil

Recommended engine oil group 1*:

SAE 10W-30/10W-40/5W-30 API SE/ SF/SG/SH/SJ/SL

Recommended engine oil group 2*:

SAE 15W-40/20W-40/20W-50 API SH/SJ/SL

Lubrication:

Wet sump

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

Page 48

Maintenance

Gear oil quantity:

F15AMH 250.0 cm3 (8.45 US oz) (8.82 Imp.oz) F9.9CE 250.0 cm

(8.45 US oz) (8.82 Imp.oz) F9.9CMH 250.0 cm3 (8.45 US oz) (8.82 Imp.oz) FT9.9DE 370.0 cm

(12.51 US oz) (13.05 Imp.oz) FT9.9DMH 370.0 cm

(12.51 US oz)

(13.05 Imp.oz)

Tightening torque for engine:

Spark plug:

18.0 Nm (13.3 ft-lb) (1.84 kgf-m)

Propeller nut:

F15AMH 17.0 Nm (12.5 ft-lb) (1.73 kgf-m) F9.9CE 17.0 Nm (12.5 ft-lb) (1.73 kgf-m) F9.9CMH 17.0 Nm (12.5 ft-lb) (1.73 kgf-m) FT9.9DE 21.0 Nm (15.5 ft-lb) (2.14 kgf-m) FT9.9DMH 21.0 Nm (15.5 ft-lb) (2.14 kgf-m)

Engine oil drain bolt:

28.0 Nm (20.7 ft-lb) (2.86 kgf-m)

Engine oil filter:

18.0 Nm (13.3 ft-lb) (1.84 kgf-m)

Noise and vibration level:

Operator sound pressure level (ICOMIA 39/94 and 40/94):

82.7 dB(A)

Vibration on tiller handle (ICOMIA 38/94):

2.7 m/s

EMU28223

Transporting and storing

outboard motor

EWM00690

WARNING

●

Leaking fuel is a fire hazard. When

transporting and storing the outboard motor, close the air vent screw and fuel cock to prevent fuel from leaking.

●

USE CARE when transporting fuel tank, whether in a boat or car. DO NOT fill fuel container to maximum

●

capacity. Gasoline will expand considerably as it warms up and can build up pressure in the fuel container. This can cause fuel leakage and a potential fire hazard.

EWM00700

WARNING

Never get under the lower unit while it is tilted, even if a motor support bar is used. Severe injury could occur if the outboard motor accidentally falls.

ECM00660

CAUTION:

The outboard motor should be trailered and stored in the normal running position. If there is insufficient road clearance in this position, then trailer the outboard motor in the tilt position using a motor support device such as a transom saver bar. Consult your Yamaha dealer for further details.

EMU28235

Clamp screw mounting models

When transporting or storing the outboard motor while removed from a boat, keep the outboard motor in the attitude shown.

Page 49

ZMU02049

ZMU02050

NOTE:

Place a towel or something similar under the outboard motor to protect it from damage.

EMU28241

Storing outboard motor

When storing your Yamaha outboard motor for prolonged periods of time (2 months or longer), several important procedures must be performed to prevent excessive damage. It is advisable to have your outboard motor serviced by an authorized Yamaha dealer prior to storage. However, you, the owner, with a minimum of tools, can perform the following procedures.

ECM01080

CAUTION:

●

To prevent problems which can be caused by oil entering the cylinder from the sump, keep the outboard motor in the attitude shown when transporting

Maintenance

and storing it. If storing or transporting the outboard motor on its side (not upright), put it on a cushion after draining the engine oil.

●

Do not place the outboard motor on its side before the cooling water has drained from it completely, otherwise water may enter the cylinder through the exhaust port and cause engine trouble.

●

Store the outboard motor in a dry, wellventilated place, not in direct sunlight.

EMU28303

Procedure

EMU28332

Flushing in a test tank

ECM00300

CAUTION:

Do not run the engine without supplying it with cooling water. Either the engine water pump will be damaged or the engine will be damaged from overheating. Before starting the engine, be sure to supply water to the cooling water passages.

1. Wash the outboard motor body using fresh water. For further information, see page 47.

2. Disconnect the fuel line from the motor or shut off the fuel cock, if equipped.

3. Remove the engine top cowling and silencer cover. Remove the propeller.

4. Install the outboard motor on the test tank. Fill the tank with fresh water to above the level of the anti-cavitation plate.

Page 50

Maintenance

ZMU02051

1. Water surface

2. Lowest water level

ECM00290

CAUTION:

If the fresh water level is below the level of the anti-cavitation plate, or if the water supply is insufficient, engine seizure may occur.

5. Cooling system flushing is essential to prevent the cooling system from clogging up with salt, sand, or dirt. In addition, fogging/lubricating of the engine is mandatory to prevent excessive engine damage due to rust. Perform the flushing and fogging at the same time.

EWM00090

WARNING

Do not touch or remove electrical parts

●

when starting or during operation. Keep hands, hair, and clothes away

●

from the flywheel and other rotating parts while the engine is running.

6. Run the engine at a fast idle for a few minutes in neutral position.

7. Just prior to turning off the engine, quickly spray “Fogging Oil” alternately into each carburetor or the fogging hole of the silencer cover, if equipped. When properly done, the engine will smoke ex-

cessively and almost stall.

8. Remove the outboard motor from the test tank.

9. Install the silencer cover/cap of fogging hole and top cowling.

10. If the “Fogging Oil” is not available, run the engine at a fast idle until the fuel system becomes empty and the engine stops.

11. Drain the cooling water completely out of the motor. Clean the body thoroughly.

12. If the “Fogging Oil” is not available, remove the spark plug(s). Pour a teaspoonful of clean engine oil into each cylinder. Crank several times manually. Replace the spark plug(s).

13. Drain the fuel from the fuel tank.

NOTE:

Store the fuel tank in a dry, well-ventilated place, not in direct sunlight.

EMU28402

Lubrication

1. Install the spark plug(s) and torque to proper specification. For information on spark plug installation, see page 54.

2. Change the gear oil. For instructions, see page 61. Inspect the oil for the presence of water that indicates a leaky seal. Seal replacement should be performed by an authorized Yamaha dealer prior to use.

3. Grease all grease fittings. For further details, see page 52.

NOTE:

For long-term storage, fogging the engine with oil is recommended. Contact your Yamaha dealer for information about fogging oil and procedures for your engine.

Page 51

Maintenance

EMU28431

Battery care

EWM00330

WARNING

Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poisonous and highly caustic. Always follow these preventive measures:

●

Avoid bodily contact with electrolytic fluid as it can cause severe burns or permanent eye injury.

●

Wear protective eye gear when handling or working near batteries.

Antidote (EXTERNAL):

●

SKIN - Flush with water. EYES - Flush with water for 15 minutes

●

and get immediate medical attention.

Antidote (INTERNAL):

Drink large quantities of water or milk

●

followed by milk of magnesia, beaten egg, or vegetable oil. Get immediate

medical attention. Batteries also generate explosive hydrogen gas; therefore, you should always follow these preventive measures:

●

Charge batteries in a well-ventilated ar-

ea.

Keep batteries away from fire, sparks,

●

or open flames (for example: welding

equipment, lighted cigarettes, and so

on.)

●

DO NOT SMOKE when charging or han-

dling batteries. KEEP BATTERIES AND ELECTROLYTIC FLUID OUT OF REACH OF CHILDREN.

Procedure

1. Disconnect and remove the battery from the boat. Always disconnect the black negative cable first to prevent the risk of shorting.

2. Clean the battery casing and terminals. Fill each cell to the upper level with distilled water.

3. Store the battery on a level surface in a cool, dry, well-ventilated place out of direct sunlight.

4. Once a month, check the specific gravity of the electrolyte and recharge as required to prolong battery life.

EMU28442

Flushing power unit

Perform this procedure right after operation for the most thorough flushing.

ECM01530

CAUTION:

Do not perform this procedure while the engine is running. The water pump may be damaged and severe damage from overheating can result.

1. After shutting off the engine, unscrew the garden hose connector from the fitting on the bottom cowling.

Follow the manual of the battery for the handling of the battery. Batteries vary among manufacturers. Therefore the following procedures may not always apply. Consult your battery manufacturer’s instructions.

Page 52

Maintenance

tion. Water will leak out of the connector instead of cooling the engine, which can cause serious overheating. Be sure the connector is tightened securely on the fitting after flushing the engine.

1. Fitting

2. Garden hose connector

3. Garden hose adapter

2. Screw the garden hose adapter onto a garden hose, which is connected to a fresh water supply, and then connect it to the garden hose connector.

3. With the engine off, turn on the water tap and let the water flush through the cooling passages for about 15 minutes. Turn off the water and disconnect the garden hose adapter from the garden hose connector.

4. Reinstall the garden hose connector onto the fitting on the bottom cowling. Tighten the connector securely.

ECM00540

CAUTION:

Do not leave the garden hose connector loose on the bottom cowling fitting or let the hose hang free during normal opera-

ZMU04887

NOTE:

●

When flushing the engine with the boat in the water, tilting up the outboard motor until it is completely out of the water will achieve better results.

●

For cooling system flushing instructions, see page 43.

EMU28450

Cleaning the outboard motor

After use, wash the exterior of the outboard motor with fresh water. Flush the cooling system with fresh water.

ZMU02052

NOTE:

For cooling system flushing instructions, see page 43.

EMU28460

Checking painted surface of motor

Check the motor for scratches, nicks, or flaking paint. Areas with damaged paint are more likely to corrode. If necessary, clean and paint the areas. A touch-up paint is available from your Yamaha dealer.

Page 53

Maintenance

EMU28478

Periodic maintenance

EWM01071

WARNING

Be sure to turn off the engine when you perform maintenance unless otherwise specified. If you are not familiar with machine servicing, this work should be done by your Yamaha dealer or other qualified mechanic.

EMU28511

Replacement parts

If replacement parts are necessary, use only genuine Yamaha parts or parts of equivalent design and quality. Any part of inferior quality may malfunction, and the resulting loss of control could endanger the operator and passengers. Yamaha genuine parts and accessories are available from your Yamaha dealer.

EMU34150

Severe operating conditions

Severe operating conditions involve one or more of the following types of operation on a regular basis:

Operating continuously at or near maxi-

●

mum engine speed (rpm) for many hours

●

Operating continuously at a low engine speed (rpm) for many hours Brief periods of rapid acceleration and de-

●

celeration followed by engine shut off before the engine has reached proper operating temperature

●

Frequent quick acceleration and deceleration Frequent shifting

●

Frequently starting and stopping the engine(s) Operation that fluctuates often between

●

light and heavy cargo loads

Outboard motors operating under any of

these above conditions require more frequent maintenance. Yamaha recommends that you do this service twice as often as specified in the maintenance chart. For example, if a particular service should be done at 50 hours, do it instead at 25 hours. This will help prevent more rapid deterioration of engine components.

Page 54

Maintenance

EMU34431

Maintenance chart 1

Frequency of maintenance operations may be adjusted according to the operating conditions, but the following table gives general guidelines. Refer to the sections in this chapter for explanations of each owner-specific action.

NOTE:

When operating in salt water, muddy, other turbid (cloudy), acidic water, the engine should be flushed with clean water after each use.

The “” symbol indicates the check-ups which you may carry out yourself. The “” symbol indicates work to be carried out by your Yamaha dealer.

Initial Every

Item Actions

Anode(s) (external)

Anode(s) (cylinder head, thermostat cover)

Anodes (exhaust cover, cooling water passage cover, Rectiﬁer Regulator cover)

Anode(s) (exhaust cover, cover joint)

Battery

Cooling water leakage

Cowling clamp Inspection

Engine starting condition/Noise

Engine idling speed/ Noise

Engine oil Replacement

Engine Oil ﬁlter (cartridge)

Fuel ﬁlter (can be disassembled)

Fuel pump

Fuel/oil leakage Inspection

Inspection or replacement as necessary

Replacement

Inspection or charging, replacement as necessary

Inspection or replacement as necessary

Inspection

Replacement

Inspection or replacement as necessary

20 hours

months)

100

hours (1

years)

300

hours (3

years)

500

hours (5

years)

Page 55

Item Actions

Fuel pipe

Fuel pipe Replacement

Gear oil Replacement

Greasing points Greasing

Impeller/water pump housing

Propeller/Propeller nut/ Cotter pin

Shift link/shift cable

Spark plug(s)

Spark plug caps/high tention cordes

Pilot water Inspection

Throttle link/Throttle cable/Throttle pick-up timing

Thermostat

Timing belt

Valve clearance

Water inlet Inspection

Main switch/stop switch/choke switch

Wire harness connections/Wire coupler connections

(Yamaha) Fuel tank

Inspection or replacement as necessary

Replacement

Inspection or replacement as necessary

Inspection, adjustment or replacement as necessary

Inspection or replacement as necessary

Inspection, adjustment or replacement as necessary

Inspection or replacement as necessary

Inspection and adjustment

Inspection or replacement as necessary

Inspection and cleaning as necessary

Maintenance

Initial Every

20 hours

months)

100

hours (1

years)

hours (3

years)

300

500

hours (5

years)

Page 56

Maintenance

EMU34450

Maintenance chart 2

Item Actions

Guide exhaust/exhaust manifold

Timing belt Replacement

EMU28910

Inspection or replacement as necessary

NOTE:

When using lead or high-sulfur gasoline, inspecting valve clearance may be required more frequently than every 500 hours.

Every

1000 hours

Page 57

EMU28941

Greasing

Yamaha grease A (water resistant grease) Yamaha grease D (corrosion resistant grease; for propeller shaft)

F9.9CE, FT9.9DE

Maintenance

ZMU02330

Page 58

Maintenance

F9.9CMH, FT9.9DMH, F15AMH

ZMU02331

Page 59

EMU28953

Cleaning and adjusting spark plug

EWM00560

WARNING

When removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow external sparks, which could lead to explosion or fire.

EWM01550

WARNING

The engine will still be very hot when it has just been turned off. Take extremely care so that neither you nor anyone else gets burnt. To avoid burns, work on the engine when it has cooled down.

The spark plug is an important engine component and is easy to inspect. The condition of the spark plug can indicate something about the condition of the engine. For example, if the center electrode porcelain is very white, this could indicate an intake air leak or carburetion problem in that cylinder. Do not attempt to diagnose any problems yourself. Instead, take the outboard motor to a Yamaha dealer. You should periodically remove and inspect the spark plug because heat and deposits will cause the spark plug to slowly break down and erode. If electrode erosion becomes excessive, or if carbon and other deposits are excessive, you should replace the spark plug with another of the correct type.

Standard spark plug:

DPR6EA-9

Before fitting the spark plug, measure the electrode gap with a wire thickness gauge; adjust the gap to specification if necessary.

Maintenance

1. Spark plug gap

2. Spark plug I.D. mark (NGK)

3. Spark plug part number

Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)

When fitting the plug, always clean the gasket surface and use a new gasket. Wipe off any dirt from the threads and screw in the spark plug to the correct torque.

Spark plug torque:

18.0 Nm (13.3 ft-lb) (1.84 kgf-m)

NOTE:

If a torque-wrench is not available when you are fitting a spark plug, a good estimate of the correct torque is 1/4 to 1/2 a turn past finger-tight. Have the spark plug adjusted to the correct torque as soon as possible with a torque-wrench.

EMU28962

Checking fuel system

EWM00060

WARNING

Gasoline and its vapors are highly flammable and explosive. Keep away from sparks, cigarettes, flames, or other

Page 60

Maintenance

sources of ignition.

EWM00910

WARNING

Leaking fuel can result in fire or explosion.

Check for fuel leakage regularly.

●

If any fuel leakage is found, the fuel system must be repaired by a qualified mechanic. Improper repairs can make the outboard unsafe to operate.

Check the fuel lines for leaks, crack, or malfunction. If a problem is found, your Yamaha dealer or other qualified mechanic should repair it immediately.

EMU28980

Inspecting fuel filter

EWM00310

WARNING

Gasoline is highly flammable, and its vapors are flammable and explosive.

●

If you have any question about properly doing this procedure, consult your Yamaha dealer.

●

Do not perform this procedure on a hot or running engine. Allow the engine to cool.

●

There will be fuel in the fuel filter. Keep away from sparks, cigarettes, flames or other sources of ignition.

●

This procedure will allow some fuel to spill. Catch fuel in a rag. Wipe up any spilled fuel immediately.

●

The fuel filter must be reassembled carefully with the O-ring, filter cup, and hoses in place. Improper assembly or replacement could result in a fuel leak, which could result in a fire or explosion hazard.

EMU29001

Cleaning fuel filter

1. Remove the nut holding the fuel filter assembly if equipped.

Checkpoints

Fuel system parts leakage

●

Fuel line joint leakage

●

Fuel line cracks or other damage Fuel connector leakage

●

ZMU02054

ZMU02055

1. Nut

Page 61

Maintenance

2. Unscrew the filter cup, catching any spilled fuel in a rag.

3. Remove the filter element, and wash it in solvent. Allow it to dry. Inspect the filter element and O-ring to make sure they are in good condition. Replace them if necessary. If any water is found in the fuel, the Yamaha portable fuel tank or other fuel tanks should be checked and cleaned.

ZMU02079

1. Filter cup

2. Filter element

3. Filter housing

4. O-ring

4. Reinstall the filter element in the cup. Make sure the O-ring is in position in the cup. Firmly screw the cup onto the filter housing.

5. Attach the filter assembly to the bracket so that the fuel hoses are attached to the filter assembly.

6. Run the engine and check the filter and lines for leaks.

EMU29041

Inspecting idling speed

EWM00451

WARNING

Do not touch or remove electrical parts

●

when starting or during operation. Keep hands, hair, and clothes away

●

from the flywheel and other rotating parts while the engine is running.

ECM00490

CAUTION:

This procedure must be performed while the outboard motor is in the water. A flushing attachment or test tank can be used.

A diagnostic tachometer should be used for this procedure. Results may vary depending on whether testing is conducted with the flushing attachment, in a test tank, or with the outboard motor in the water.

1. Start the engine and allow it to warm up fully in neutral until it is running smoothly.

NOTE:

Correct idling speed inspection is only possible if the engine is fully warmed up. If not warmed up fully, the idle speed will measure higher than normal. If you have difficulty verifying the idle speed, or the idle speed requires adjustment, consult a Yamaha dealer or other qualified mechanic.

2. Verify whether the idle speed is set to specification. For idle speed specifications, see page 41.

EMU29074

Changing engine oil

EWM00760

WARNING

●

Avoid draining the engine oil immediately after stopping the engine. The oil is hot and should be handled with care to avoid burns.

●

Be sure the outboard motor is securely fastened to the transom or a stable

Page 62

Maintenance

stand.

ECM00970

CAUTION:

●

Do not overfill the oil, and be sure the outboard motor is upright (not tilted) when checking and changing the engine oil.

●

If the oil level is above the upper level mark, drain until the level meets the specified capacity. Overfilling the oil could cause leakage or damage.

ECM01240

CAUTION:

Change the engine oil after the first 10 hours of operation, and every 100 hours or at 6-month intervals thereafter. Otherwise the engine will wear quickly.

ZMU02056

1. Drain screw

3. Put a new gasket on the oil drain screw. Apply a light coat of oil to the gasket and install the drain screw.

Drain screw tightening torque:

28.0 Nm (20.7 ft-lb) (2.86 kgf-m)

NOTE:

Change the engine oil when the oil is still warm.

1. Put the outboard motor in an upright position (not tilted).

ZMU02049

2. Prepare a suitable container that holds a larger amount than the engine oil capacity. Loosen and remove the drain screw while holding the container under the drain hole. Then remove the oil filler cap. Let the oil drain completely. Wipe up any spilled oil immediately.

NOTE:

If a torque wrench is not available when you are installing the drain screw, finger tighten the screw just until the gasket comes into contact with the surface of the drain hole. Then tighten 1/4 to 1/2 turn more. Tighten the drain screw to the correct torque with a torque wrench as soon as possible.

4. Add the correct amount of oil through the filler hole. Install the filler cap.

Recommended engine oil:

4-stroke outboard motor oil

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

Page 63

ZMU02057

5. Start the engine and watch to make sure the low oil pressure-warning indicator (if equipped) turns off. Make sure that there are no oil leaks.

ECM00681

CAUTION:

If the low oil pressure-warning indicator does not turn off or if there are oil leaks, stop the engine and find the cause. Continued operation with a problem could cause severe engine damage. Consult your Yamaha dealer if the problem cannot be located and corrected.

6. Turn off the engine and wait 3 minutes. Recheck the oil level using the dipstick to be sure the level falls between the upper and lower marks. Fill with oil if it is below the lower mark, or drain to the specified level if it is above the upper mark.

ZMU02058

Maintenance

7. Dispose of used oil according to local regulations.

NOTE:

●

For more information on the disposal of used oil, consult your Yamaha dealer.

●

Change the oil more often when operating the engine under adverse conditions such as extended trolling.

EMU29112

Checking wiring and connectors

●

Check that each grounding wire is properly secured.

●

Check that each connector is engaged securely.

ZMU02087

EMU29120

Exhaust leakage

Start the engine and check that no exhaust leaks from the joints between the exhaust cover, cylinder head, and body cylinder.

EMU29130

Water leakage

Start the engine and check that no water leaks from the joints between the exhaust cover, cylinder head, and body cylinder.

EMU29140

Engine oil leakage

Check for oil leaks on the around the engine.

NOTE:

If any leaks are found, consult your Yamaha dealer.

Page 64

Maintenance

EMU32110

Checking propeller

EWM01610

WARNING

You could be seriously injured if the engine accidentally starts when you are near the propeller.

Before inspecting, removing, or install-

●

ing the propeller, remove the spark plug caps from the spark plugs. Also, place the shift control in neutral, turn the main switch to “” (off) and re- move the key, and remove the cord from the engine shut-off switch. Turn off the battery cut-off switch if your boat has one. Do not use your hand to hold the pro-

●

peller when loosening or tightening the propeller nut. Put a wood block between the anti-cavitation plate and the propeller to prevent the propeller from turning.

ZMU01897

Checkpoints

●

Check each of the propeller blades for wear, erosion from cavitation or ventilation, or other damage.

●

Check the propeller shaft for damage.

●

Check the splines for wear or damage. Check for fish line tangled around the pro-

●

peller shaft.

ZMU02059

●

Check the propeller shaft oil seal for damage.

EMU30661

Removing propeller

EMU29195

Spline models

1. Straighten the cotter pin and pull it out using a pair of pliers.

2. Remove the propeller nut, washer, and spacer (if equipped).

Page 65

ZMU02062

1. Cotter pin

2. Propeller nut

3. Washer

4. Propeller

5. Thrust washer

3. Remove the propeller and thrust washer.

EMU29213

Dual thrust models

1. Straighten the cotter pin and pull it out using a pair of pliers.

Maintenance

EMU30671

Installing propeller

EMU29231

Spline models

ECM00340

CAUTION:

Be sure to install the thrust washer be-

●

fore installing the propeller, otherwise the lower case and propeller boss could be damaged.

●

Be sure to use a new cotter pin and bend the ends over securely. Otherwise the propeller could come off during operation and be lost.

1. Apply Yamaha marine grease or a corrosion resistant grease to the propeller shaft.

2. Install the spacer (if equipped), thrust washer, and propeller on the propeller shaft.

3. Install the spacer (if equipped) and the washer. Tighten the propeller nut to the specified torque.

4. Align the propeller nut with the propeller shaft hole. Insert a new cotter pin in the hole and bend the cotter pin ends.

1. Cotter pin

2. Propeller nut

3. Washer

4. Deﬂector

5. Propeller

6. Thrust washer

2. Remove the propeller nut and washer.

3. Remove the deflector, propeller, and thrust washer.

ZMU02329

ZMU02063

NOTE:

If the propeller nut does not align with the propeller shaft hole after tightening to the specified torque, tighten the nut further to align it with the hole.

Page 66

Maintenance

EMU29262

Dual thrust models

ECM00340

CAUTION:

●

Be sure to install the thrust washer before installing the propeller, otherwise the lower case and propeller boss could be damaged. Be sure to use a new cotter pin and

●

bend the ends over securely. Otherwise the propeller could come off during operation and be lost.

1. Apply Yamaha marine grease or a corrosion resistant grease to the propeller shaft.

2. Install the thrust washer and propeller on the propeller shaft. Install the deflector on the propeller.

3. Install the washer and tighten the propeller nut to the specified torque.

4. Align the propeller nut with the propeller shaft hole. Insert a new cotter pin in the hole and bend the cotter pin ends.

EMU29282

Changing gear oil

EWM00800

WARNING

Be sure the outboard motor is securely

●

fastened to the transom or a stable stand. You could be severely injured if the outboard motor falls on you.

●

Never get under the lower unit while it is tilted, even when the tilt support lever or knob is locked. Severe injury could occur if the outboard motor accidentally falls.

1. Tilt the outboard motor so that the gear oil drain screw is at the lowest point possible.

2. Place a suitable container under the gear case.

3. Remove the gear oil drain screw and gasket.

ZMU02063

NOTE:

If the propeller nut does not align with the propeller shaft hole after tightening to the specified torque, tighten the nut further to align it with the hole.

ZMU02064

1. Gear oil drain screw

2. Oil level plug

NOTE:

If a magnetic gear oil drain screw is

●

equipped, remove all metal particles from the screw before installing it. Always use new gaskets. Do not reuse the

●

removed gaskets.

4. Remove the oil level plug and gasket to

Page 67

Maintenance

allow the oil to drain completely.

ECM00710

CAUTION:

Inspect the used oil after it has been drained. If the oil is milky, water is getting into the gear case which can cause gear damage. Consult a Yamaha dealer for repair of the lower unit seals.

NOTE:

For disposal of used oil, consult your Yamaha dealer.

5. With the outboard motor in a vertical position, and using a flexible or pressurized filling device, inject the gear oil into the gear oil drain screw hole.

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F15AMH 250.0 cm (8.82 Imp.oz) F9.9CE 250.0 cm3 (8.45 US oz) (8.82 Imp.oz) F9.9CMH 250.0 cm (8.82 Imp.oz) FT9.9DE 370.0 cm (13.05 Imp.oz) FT9.9DMH 370.0 cm3 (12.51 US oz) (13.05 Imp.oz)

(8.45 US oz)

(12.51 US oz)

6. Put a new gasket on the oil level plug. When the oil begins to flow out of the oil level plug hole, insert and tighten the oil level plug.

7. Put a new gasket on the gear oil drain screw. Insert and tighten the gear oil drain screw.

EMU29302

Cleaning fuel tank

EWM00920

WARNING

Gasoline is highly flammable, and its vapors are flammable and explosive.

If you have any question about properly

●

doing this procedure, consult your Yamaha dealer. Keep away from sparks, cigarettes,

●

flames, or other sources of ignition when cleaning the fuel tank. Remove the fuel tank from the boat be-

●

fore cleaning it. Work only outdoors in an area with good ventilation. Wipe up any spilled fuel immediately.

●

Reassemble the fuel tank carefully. Improper assembly can result in a fuel leak, which could result in a fire or explosion hazard.

●

Dispose of old gasoline according to local regulations.

1. Empty the fuel tank into an approved container.

2. Pour a small amount of suitable solvent into the tank. Install the cap and shake the tank. Drain the solvent completely.

3. Remove the screws holding the fuel joint assembly. Pull the assembly out of the tank.

ZMU02065

Page 68

Maintenance

ZMU02067

4. Clean the filter (located on the end of the suction pipe) in a suitable cleaning solvent. Allow the filter to dry.

5. Replace the gasket with a new one. Reinstall the fuel joint assembly and tighten the screws firmly.

EMU29312

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from corrosion by sacrificial anodes. Inspect the external anodes periodically. Remove scales from the surfaces of the anodes. Consult a Yamaha dealer for replacement of external anodes.

ECM00720

CAUTION:

Do not paint anodes, as this would render them ineffective.

NOTE:

Inspect ground leads attached to external anodes on equipped models. Consult a Yamaha dealer for inspection and replacement of internal anodes attached to the power unit.

EMU29320

Checking battery (for electric start models)

EWM00330

WARNING

Battery electrolytic fluid is dangerous; it contains sulfuric acid and therefore is poisonous and highly caustic. Always follow these preventive measures:

●

Avoid bodily contact with electrolytic fluid as it can cause severe burns or permanent eye injury.

●

Wear protective eye gear when handling or working near batteries.

Antidote (EXTERNAL):

●

SKIN - Flush with water. EYES - Flush with water for 15 minutes

●

and get immediate medical attention.

Antidote (INTERNAL):

Drink large quantities of water or milk

●

followed by milk of magnesia, beaten egg, or vegetable oil. Get immediate

medical attention. Batteries also generate explosive hydrogen gas; therefore, you should always follow these preventive measures:

●

Charge batteries in a well-ventilated ar-

ea.

Keep batteries away from fire, sparks,

●

or open flames (for example: welding

Page 69

Maintenance

equipment, lighted cigarettes, and so on.) DO NOT SMOKE when charging or han-

●

dling batteries. KEEP BATTERIES AND ELECTROLYTIC FLUID OUT OF REACH OF CHILDREN.

ECM00360

CAUTION:

●

A poorly maintained battery will quickly

deteriorate.

●

Ordinary tap water contains minerals

harmful to a battery, and should not be

used for topping up.

1. Check the electrolyte level at least once

a month. Fill to the manufacturer’s recommended level when necessary. Top up only with distilled water (or pure deionized water suitable to use in batteries).

NOTE:

Consult a Yamaha dealer when charging or re-charging batteries.

EMU29332

Connecting the battery

EWM00570

WARNING

Mount the battery holder securely in a dry, well-ventilated, vibration-free location in the boat. Install a fully charged battery in the holder.

ECM01122

CAUTION:

●

Make sure the main switch (on applicable models) is “” (off) before work- ing on the battery.

●

Reversal of the battery cables will damage the electrical parts.

●

Connect the red battery cable first when installing the battery and disconnect the black battery cable first when removing it.

●

The electrical contacts of the battery and cables must be clean and properly connected, or the battery will not start the engine.

2. Always keep the battery in a good state

of charge. Installing a voltmeter will help you monitor your battery. If you will not use the boat for a month or more, remove the battery from the boat and store it in a cool, dark place. Completely recharge the battery before using it.

3. If the battery will be stored for longer

than a month, check the specific gravity of the fluid at least once a month and recharge the battery when it is low.

Connect the red battery cable to the POSITIVE (+) terminal first. Then connect the black battery cable to the NEGATIVE (-) terminal.

Page 70

Maintenance

1. Red cable

2. Black cable

3. Battery

EMU29370

Disconnecting the battery

Disconnect the BLACK cable from the NEGATIVE (-) terminal first. Then disconnect the RED cable from the POSITIVE (+) terminal.

EMU29391

Checking top cowling

ECM01650

CAUTION:

Be sure the cowling is closed securely and that there are no gaps. A loose or improperly fitting cover could allow water into the engine.

EMU29400

Coating the boat bottom

A clean hull improves boat performance. The boat bottom should be kept as clean of marine growth as possible. If necessary, the boat bottom can be coated with an anti-fouling paint approved for your area to inhibit marine growth. Do not use anti-fouling paint which includes copper or graphite. These paints can cause more rapid engine corrosion.

ZMU01943

Check the fitting of the top cowling by pushing it with both hands. If it is loose have it repaired by your Yamaha dealer.

ZMU02068

Page 71

Trouble Recovery

EMU29425

Troubleshooting

A problem in the fuel, compression, or ignition systems can cause poor starting, loss of power, or other problems. This section describes basic checks and possible remedies, and covers all Yamaha outboard motors. Therefore some items may not apply to your model. If your outboard motor requires repair, bring it to your Yamaha dealer. If the engine trouble-warning indicator is flashing, consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low? A. Check battery condition. Use battery of recommended capacity.

Q. Are battery connections loose or corroded? A. Tighten battery cables and clean battery terminals.

Q. Is fuse for electric start relay or electric circuit blown? A. Check for cause of electric overload and repair. Replace fuse with one of correct amperage.

Q. Are starter components faulty? A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear? A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty? A. Fill tank with clean, fresh fuel.

A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged? A. Clean or replace filter.

Q. Is starting procedure incorrect? A. See page 28.

Q. Has fuel pump malfunctioned? A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect type? A. Inspect spark plug(s). Clean or replace with recommended type.

Q. Are spark plug cap(s) fitted incorrectly? A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly connected? A. Check wires for wear or breaks. Tighten all loose connections. Replace worn or broken wires.

Q. Are ignition parts faulty? A. Have serviced by a Yamaha dealer.

Q. Is engine shut-off cord not attached? A. Attach cord.

Q. Are engine inner parts damaged? A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect type? A. Inspect spark plug(s). Clean or replace with recommended type.

Q. Is fuel contaminated or stale?

Q. Is fuel system obstructed?

Page 72

Trouble Recovery

A. Check for pinched or kinked fuel line or other obstructions in fuel system.

Q. Is fuel contaminated or stale? A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged? A. Clean or replace filter.

Q. Have ignition parts failed? A. Have serviced by a Yamaha dealer.

Q. Has warning system activated? A. Find and correct cause of warning.

Q. Is spark plug gap incorrect? A. Inspect and adjust as specified.

Q. Is ignition wiring damaged or poorly connected? A. Check wires for wear or breaks. Tighten all loose connections. Replace worn or broken wires.

Q. Is motor angle too high? A. Return to normal operating position.

Q. Is carburetor clogged? A. Have serviced by a Yamaha dealer.

Q. Is fuel joint connection incorrect? A. Connect correctly.

Q. Is throttle valve adjustment incorrect? A. Have serviced by a Yamaha dealer.

Q. Is battery cable disconnected? A. Connect securely.

Warning buzzer sounds or indicator lights.

Q. Is cooling system clogged? A. Check water intake for restriction.

Q. Is engine oil level low? A. Fill oil tank with specified engine oil.

Q. Is specified engine oil not being used? A. Check and replace oil as specified.

Q. Is thermostat faulty or clogged? A. Have serviced by a Yamaha dealer.

Q. Are carburetor adjustments incorrect? A. Have serviced by a Yamaha dealer.

Q. Is fuel pump damaged? A. Have serviced by a Yamaha dealer.

Q. Is air vent screw on fuel tank closed? A. Open air vent screw.

Q. Is choke knob pulled out? A. Return to home position.

Q. Is heat range of spark plug incorrect? A. Inspect spark plug and replace it with recommended type.

Q. Is specified engine oil not being used? A. Check and replace oil with specified type.

Q. Is engine oil contaminated or deteriorated? A. Replace oil with fresh, specified type.

Q. Is oil filter clogged? A. Have serviced by a Yamaha dealer.

Q. Has oil feed/injection pump malfunctioned? A. Have serviced by a Yamaha dealer.

Page 73

Q. Is load on boat improperly distributed? A. Distribute load to place boat on an even plane.

Q. Is water pump or thermostat faulty? A. Have serviced by a Yamaha dealer.

Trouble Recovery

on gear housing? A. Remove foreign matter and clean lower unit.

Q. Is fuel system obstructed? A. Check for pinched or kinked fuel line or other obstructions in fuel system.

Q. Is there excess water in fuel filter cup? A. Drain filter cup.

Engine power loss.

Q. Is propeller damaged? A. Have propeller repaired or replaced.

Q. Is propeller pitch or diameter incorrect? A. Install correct propeller to operate outboard at its recommended speed (r/min) range.

Q. Is trim angle incorrect? A. Adjust trim angle to achieve most efficient operation.

Q. Is motor mounted at incorrect height on transom? A. Have motor adjusted to proper transom height.

Q. Has warning system activated? A. Find and correct cause of warning.

Q. Is boat bottom fouled with marine growth? A. Clean boat bottom.

Q. Is fuel filter clogged? A. Clean or replace filter.

Q. Is fuel contaminated or stale? A. Fill tank with clean, fresh fuel.

Q. Is spark plug gap incorrect? A. Inspect and adjust as specified.

Q. Is ignition wiring damaged or poorly connected? A. Check wires for wear or breaks. Tighten all loose connections. Replace worn or broken wires.

Q. Have electrical parts failed? A. Have serviced by a Yamaha dealer.

Q. Is specified fuel not being used? A. Replace fuel with specified type.

Q. Is specified engine oil not being used? A. Check and replace oil with specified type.

Q. Is thermostat faulty or clogged? A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect type? A. Inspect spark plug(s). Clean or replace with recommended type.

Q. Are weeds or other foreign matter tangled

Q. Is air vent screw closed? A. Open the air vent screw.

Q. Is fuel pump damaged? A. Have serviced by a Yamaha dealer.

Page 74

Trouble Recovery

Q. Is fuel joint connection incorrect? A. Connect correctly.

Q. Is heat range of spark plug incorrect? A. Inspect spark plug and replace it with recommended type.

Q. Is high pressure fuel pump drive belt broken? A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift lever position? A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged? A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged? A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled on propeller? A. Remove and clean propeller.

Q. Is motor mounting bolt loose? A. Tighten bolt.

Q. Is steering pivot loose or damaged? A. Tighten or have serviced by a Yamaha dealer.

EMU29433

Temporary action in

emergency

EMU29440

Impact damage

EWM00870

WARNING

The outboard motor can be seriously damaged by a collision while operating or

trailering. Damage could make the outboard motor unsafe to operate.

If the outboard motor hits an object in the water, follow the procedure below.

1. Stop the engine immediately.

2. Inspect the control system and all components for damage. Also inspect the boat for damage.

3. Whether damage is found or not, return to the nearest harbor slowly and carefully.

4. Have a Yamaha dealer inspect the outboard motor before operating it again.

EMU29462

Replacing fuse

If the fuse has blown on an electric start model, open the fuse holder and replace the fuse with a new one of the proper amperage.

EWM00630

WARNING

Be sure to use the specified fuse. An incorrect fuse or a piece of wire could allow excessive current flow. This could cause electric system damage and a fire hazard.

Page 75

ZMU02092

1. Fuse holder

2. Fuse (20 A)

3. Spare fuse (20 A)

NOTE:

Consult your Yamaha dealer if the new fuse immediately blows again.

EMU29533

Starter will not operate

If the starter mechanism does not operate (the engine cannot be cranked with the starter), the engine can be started with an emergency starter rope.

EWM01022

WARNING

Use this procedure only in an emergen-

●

cy to return to the nearest port for repairs. When the emergency starter rope is

●

used to start the engine, the start-ingear protection device does not operate. Make sure the remote control lever is in neutral. Otherwise the boat could unexpectedly start to move, which could result in an accident.

●

Attach the engine shut-off cord to a secure place on your clothing, or your arm or leg while operating the boat.

●

Do not attach the cord to clothing that could tear loose. Do not route the cord where it could become entangled, pre-

Trouble Recovery

venting it from functioning.

●

you when pulling the starter rope. It could whip behind you and injure someone.

●

An unguarded, rotating flywheel is very dangerous. Keep loose clothing and other objects away when starting the engine. Use the emergency starter rope only as instructed. Do not touch the flywheel or other moving parts when the engine is running. Do not install the starter mechanism or top cowling after the engine is running.

●

Do not touch the ignition coil, spark plug wire, spark plug cap, or other electrical components when starting or operating the motor. You could get an electrical shock.

EMU29603

Emergency starting engine

1. Remove the top cowling.

2. Remove the cable by pulling out it from the starter, if the cable is equipped.

Page 76

Trouble Recovery

the engine is in neutral and that the clip is attached to the engine shut-off switch.

ZMU02069

1. Start-in-gear protection cable

3. Remove both ends of the choke link rod.

ZMU02332

1. Choke link rod

4. Remove the starter/flywheel cover after removing the 3 bolts. Disconnect the wire leads from the starter/flywheel cover.

ZMU02026

ZMU02334

6. Pull up the lever on the carburetor to operate the choke system when the engine is cold. After the engine starts, return the lever to the original position.

ZMU02070

5. Prepare the engine for starting. For further information, see page 28. Be sure

ZMU02333

7. Insert the knotted end of the emergency starter rope into the notch in the flywheel rotor and wind the rope around the flywheel several turns clockwise.

Page 77

ZMU02074

8. Pull the rope slowly until resistance is felt.

9. Give a strong pull straight out to crank and start the engine. Repeat if necessary.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immediately take it to a Yamaha dealer. Otherwise some corrosion may begin almost immediately. If you cannot immediately take the outboard motor to a Yamaha dealer, follow the procedure below in order to minimize engine damage.

EMU29783

Procedure

1. Thoroughly wash away mud, salt, seaweed, and so on, with fresh water.

2. Remove the spark plug(s), then face the spark plug holes downward to allow any water, mud, or contaminants to drain.

3. Drain the fuel from the carburetor, fuel filter, and fuel line. Drain the engine oil completely.

4. Fill the sump with the fresh engine oil.

Trouble Recovery

holes while cranking the engine with the manual starter or emergency starter rope.

6. Take the outboard motor to a Yamaha dealer as soon as possible.

ECM00400

CAUTION:

Do not attempt to run the outboard motor until it has been completely inspected.

Engine oil capacity:

1.0 L (1.06 US qt) (0.88 Imp.qt)

5. Feed engine fogging oil or engine oil through the carburetor(s) and spark plug

Page 78

YAMAHA MOTOR CO., LTD.

Printed in Japan March 2007–0.1 × 1

Printed on recycled paper

Yamaha F15A, F9.9C, FT9.9D User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

General information

Safety information

Basic requirements

Basic components

Operation

Maintenance

Trouble Recovery