Yamaha ELB01E3, ELB01 User Manual

Page 1

ELB-01 Assembly Instructions

Carefully read these instructions BEFORE assembling the Electone.

Be careful not to confuse any of the parts, and be sure to install all parts in the correct direction by following the procedures given below.

Be sure to assemble the Electone with two or more people.

Don’t use any screws other than the ones speciﬁed and included in this package. Use of incorrect screws can cause damage and malfunction.

Be sure to tighten all screws upon completing assembly.

Make sure to perform all assembly operations on a ﬂat surface.

To disassemble, reverse the procedures.

You need a Phillips (+) screwdriver to assemble the Electone.

Open the package, take out the two styrofoam pads from the both sides of the package, and carefully

place the main unit on top of the pads as shown.

Take care not to pinch AC power cord plug between the pads and Main unit.

Take out all parts from the package.

Please conﬁrm that all parts shown in the illustration are provided. When you take out the Speaker Unit, always hold the bottom of the Speaker Unit, not holding the Grill Net.

Dust Cover

Styrofoam pads

Take out the styrofoam pads, and place the Main Unit on top of the pads.

Grill Net

Attached to the Speaker Unit

Music Rest

Main Unit

Long screws (ø6 X 25 mm): 4 pcs.

Short screws (ø5 X 12 mm): 8 pcs.

Pedalboard cord clamps: 2 pcs.

Speaker Unit

Screw caps: 4 pcs.

Sideboard

(Left)

Sideboard

(Right)

Bench

Pedalboard Unit

ELB-01 Assembly Instructions

Bench Board

Legs: 4 pcs.

Page 2

Mount the Sideboards onto the Pedalboard

unit.

Be sure not to confuse the Right and Left Sideboards.

3-1 Raise the Pedalboard as shown in the illustration

below.

3-2 Position each screw hole on both the Pedalboard

and Sideboards as shown in the illustration and mount the Sideboards onto the Pedalboard using the 4 short screws (2 screws on each Sideboard).

4-3 While holding the Sideboard(s) to the Speaker

unit, fasten the four short screws from the rear, to secure the Speaker unit to the Sideboards. Cover the four screw holes on the rear side with the corresponding screw caps.

Push the Sideboard toward the Speaker unit

Push the Sideboard toward the Pedalboard

Short/black screws

3-3 Stand the Pedalboard after securing the screws.

Mount the Speaker Unit onto the Sideboards.

4-1 Remove the Grill Net from the Speaker Unit.

Short

Short screws

Screw caps

Mount the Main Unit.

Screw caps

screws

5-1 As shown in the illustration, hold the Main unit

horizontally (with two people), and place it on the front side of the Speaker unit so that the arm at the bottom of the Main unit comes in front of the Sideboards, then slide it to the rear side.

4-2 With the help of another person, hold the Speaker

unit horizontally, and slide it from the rear into place along the brackets.

Take care not to drop the Speaker unit or to pinch your ﬁnger(s) between the Speaker unit and Sideboard.

ELB-01 Assembly Instructions

1. Place down so that the arm comes in front of the Sideboard

Arm

2. Slide to the rear side

Take care not to drop the Main unit or to pinch your ﬁnger(s) between the Speaker unit and Main unit.

Page 3

5-2 Use the four long screws to fasten the Main unit to

the Sideboards as shown in the illustration.

Long screw

Connect the Pedalboard cord and Speaker cord to the Main Unit.

Make sure that the latches on each plug of the cords face toward you, and connect them to each socket securely.

Speaker cord Pedalboard cord

Fix the Pedalboard cord to the Sideboard using the Pedalboard cord clamps.

8-1 Afﬁx the two Pedalboard cord clamps to the rear

side of the Speaker unit and the lower inside of the Left Sideboard as shown in the illustration.

Fit the Grill Net onto the Speaker.

First, align the net with the bottom line, then secure it to the speaker assembly.

Fasten the Grill Net by inserting the knobs into the holes.

8-2 Insert the Pedalboard cord in the clamps.

Shut the clamp after inserting the cord.

ELB-01 Assembly Instructions

Page 4

Place the music rest on the Electone.

Turn on the Electone’s power switch and conﬁrm that the Electone can be played, and that the assembly is successful.

After completing the assembly, please check the following items.

• Are there any parts left over?

→ Review all assembly procedures.

• Is the Electone clear of doors and other movable ﬁxtures?

→ Move the Electone to an appropriate location.

• Does the Electone make a rattling noise when you shake it?

→ Tighten all screws.

• Can the Electone be turned on?

→ Conﬁrm that the AC power cord plug is securely connected to an appropriate power outlet.

• Does the Electone produce sounds?

→ Conﬁrm that the Speaker cord plug and the Pedalboard cord plug are securely connected to each socket on the Main unit.

If the Electone creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly instructions and tighten all screws again.

BENCH ASSEMBLY

Turn the bench board over and put the legs in place, one by one, at the corners of the bench board, then tighten each nut using the included wrench. Be sure to put the washer between each leg and nut as shown.

Leg

Washer

Bench board

Nut

ELB-01 Assembly Instructions

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

WF43900 510MWAP3.3-01A0

Printed in China