Yamaha 02R96 User Manual

❏

❏

02R96 V2.2 Supplementary Manual

The 02R96 System Software Version 2.20 features the following changes and additions (including the changes made
up to Version 2.11).

Changes and additions in Version 2.20

More Add-On Effects Packages available (pages 155 and 158)

The following Add-On Effects Packages are now available:

• AE041 Surround Post Package

• AE051 Vintage Stomp Package

Due to this addition, effect memories #53 through 67 in the Effects library are now designated as preset effects pro­grams. These preset programs are dedicated to Add-On Effects. The numbers of effects programs that do not have
Add-On Effects installed are grayed out and cannot be used. The following effects programs in the Effects library
have been dedicated to the new Add-On Effects Packages.

No. Preset name Type

62 Room ER ROOM ER

63 Auto Doppler AUTO DOPPLER

64 Field Rotation FLD ROTATION

65 Max100 MAX100

66 Vintage Phaser VNTG PHASER

67 Dual Phaser DUAL PHASER

Please refer to the following Yamaha website for the latest information on the Add-On Effects Packages:

http://www.yamahaproaudio.com

Additional trigger sources in the GPI OUTPUT section (pages 225 and 254)

The following parameters have been added as the trigger signal source in the GPI OUTPUT section.

xxx ON TALLY: The trigger signal is active only while the corresponding channel is turned ON.

The following parameters have been added in the OUTPUT list of the “GPI Trigger Source & Target List” on

❏

page 254.

# Source

254 CH1 ON TALLY

:

309 CH56 ON TALLY

310 BUS1 ON TALLY

:

317 BUS8 ON TALLY

318 AUX1 ON TALLY

:

325 AUX8 ON TALLY

326 ST ON TALLY

About the 02R96 Editor version

If you use the 02R96 Editor (Studio Manager) to control the 02R96, update the 02R96 Editor to version 2.1.2 or
higher (Studio Manager version 2.1 or higher).

If your Studio Manager CD-ROM version is not X5401 B0 , download the latest version from the following Yamaha
website:

http://www.yamahaproaudio.com

EN

Changes in V2.11

Y96K card and MY16-mLAN card support (pages 59 and 299)

The Waves Y96K Plug-in DSP card (supported by Version 2.10) and the MY16-mLAN interface card are now sup­ported. Also, in accordance with the mLAN MIDI specifications, multiple MIDI ports on SLOT 1 have been
changed to a single port. (Now you do not need to select Ports 1-8.)

Please refer to the following website for the latest information on compatible cards, and on the number of cards
that can be installed in combination with other cards.

http://www.yamahaproaudio.com

Changes in V2.10

MIX C-R SOURCES parameter added to
Control Room Monitor (page 137)

A “MIX C-R SOURCES” parameter has been added in the
CONTROL ROOM SETUP page. In V2.0, you could
choose one item from 2TR D1, D2, D3, A1, or A2 as a
monitor source, plus other sources (STEREO, ASSIGN1,
or ASSIGN2). In V2.1, you can turn the MIX C-R
SOURCES parameter off to disable this simultaneous
selection.

MIX MONITOR SOURCES parameter
added to Surround Monitor (page 138)

A “MIX MONITOR SOURCES” parameter has been
added to the SURROUND MONITOR page. In V2.0, you
could simultaneously choose a BUS and SLOT as the
monitor source, but in V2.1 you can turn this parameter
off to disable this simultaneous selection.

❏

❏

❏

THX presets added to Surround Monitor (page 139-141)

Presets for the THX pm3 monitor system have been added to the bass management settings for surround monitor­ing. Several supplements have also been added regarding the surround monitor settings, so please replace the cor­responding pages with the following.

Configuring Surround Monitoring

Surround monitoring, including speaker setup, monitor matrix, Bass Management, and mon­itor alignment, is configured on the Surround Monitor Setup page.

1 Use the MONITOR [DISPLAY] button to locate the Surround Monitor Setup

page.

2 Use the cursor buttons to select the parameters, and use the Parameter wheel,

INC/DEC buttons, and [ENTER] button to set them.

SPEAKER SETUP:

itor speakers. Select the OSC (Oscillator) parameter and choose from PINK NOISE, 500-2K
(pink noise through a 500 Hz to 2 kHz BPF), 1K (1 kHz sinewave), or 50 Hz (50 Hz sinewave).
Use the ON/OFF button to turn the Oscillator on and off. When on, the Oscillator outputs a
signal at –20 dB to the Surround Channels whose icons are highlighted. You can turn on and
off Oscillator output for speakers individually. Speaker icons can be selected by using the cursor
buttons. The signal phase of the LFE Channel can be reversed by using the SW phase button.
When ROTATE is on, the Oscillator signal is output by each speaker in turn in a clockwise
direction (3 second signal, 2 second pause).

❏

SURR. MODE: This indicates the currently selected Surround mode, which is set on the Sur-

round Mode page (see page 85).

Note: If you had been monitoring with the surround mode set to 6.1 and the monitor matrix mode

set to 6.1 on 02R96 units with system software earlier than V2.1, the playback may not always be
correct on V2.1.

MONITOR MATRIX: This is used to select the Surround Monitor Matrix. In 6.1 Surround

mode, you can select 6.1, 5.1, 3-1, or ST. In 5.1 Surround mode, you can select 5.1, 3-1, or ST.
In 3-1 Surround mode, you can select 3-1 or ST.

When a down mix Monitor Matrix is selected, you can attenuate signals by using the ATT
parameters.

You can use the Surround Monitor settings in Stereo mode, but Monitor Matrix is fixed to ST.

These parameters are for setting the volume balance of the surround mon-

Note: If you choose monitor matrix mode = 3-1, you must set the following three attenuation

amounts to the same value.

• ATT1 for surround mode 3-1

• ATT4 for surround mode 5.1

• ATT5 for surround mode 6.1
These ATT values are not attenuators for down-mixing; rather, they are used as monitor adjust­ment attenuators for lowering the playback volume of the Ls, Rs, Ls2, and Rs2 speakers.