Yamaha 01X Reference Manual
Quick Reference
Recording to Computer/Audio Sequencer (DAW)
Direct Recording
In this setup, you can directly record the eight analog inputs of the 01X
(or up to 24 channels via the mLAN connection). Unless you’ve
changed the settings, the 01X is set up for this operation by default.
Check that the input signal is not clipping or overloading from
Adjust the input gain
2
to match the output
of the device. (p. 16)
Connect the devices
1
to be recorded to
the 01X inputs.
Mic
Mic
Synthesizer
the horizontal level meter display on the 01X LCD. (p. 46)
INPUT METER POINT = PRE EQ: input signal clip display
input signal clip
You can bypass the EQ and Dynamics processing and
send the signal direct to the mLAN output.
DIRECT OUT Position = PRE EQ (p. 91)
4-band EQ
Dynamics
4-band EQ
Dynamics
4-band EQ
Dynamics
4-band EQ
Dynamics
Set up the computer (with
6
mLAN connection) and audio
sequencer for recording.
1. Using the mLAN Auto Connector,
make sure the number of
channels (in “From 01X to
PC/Mac”) is equal to or higher
than the number of channels to
be recorded. (Guide, pp. 9, 20)
2. Select the input channels of the
mLAN Audio Driver on the
sequencer. (p. 69)
Audio Sequencer
Audio Track 01
Audio Track 02
Audio Track 03
Audio Track 04
Recording a Mix
In this setup, you can record a mix of all 01X inputs, sending the stereo bus
to mLAN Out.
Ex. • Simultaneous recording of several MIDI tone generators with live instruments and microphones.
• Mixing the individual outputs of a rhythm machine (with separate EQ and Dynamics on the 01X).
Mic
Synthesizer
Synthesizer
Synthesizer
01X
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
EQ, Dyn, Vol, Pan
Effect 1, 2
Mix
The Stereo Bus signal is
sent to the mLAN output.
ST-BUS → [1/2] in the
OUT PATCH (mLAN Out
Channel) (p. 90)
In this situation, direct
recording of channels
1 and 2 (as in “Direct
Recording” above) is
not possible.
Computer
Monitor
Guitar
Effects can also be
inserted in the signal
path of each channel.
Effect 1/2 PATCH
= channel number
(p. 102)
Apply effects, such as reverb,
3
for monitoring purposes by adjusting
the levels of Aux Send 3 (or 4) in the
individual channels and STI 1 (or 2) in
the Master layer (with faders). (The effect
is not recorded; only the dry signal is.)
* In these explanations, normal page references are to the 01X Owner’s Manual; those indicated by “Guide” are to the 01X Installation Guide.
For more information, make sure to refer to the “Overview of the 01X” on page 25 of the Owner’s Manual, as well as the block diagram at the end of the manual.
Effect 2
(ex. Dist.)
01X
4-band EQ
Dynamics
SEND3
Effect 1
(Reverb)
STI1 Fader
Adjust the direct monitor level for each
4
channel to be recorded with the individual
channel faders.
This allows you to monitor
without latency (delay).
You can also record the mLAN output,
adjusting the output level with the fader. (p. 91)
DIRECT OUT POSITION = POST FADER
Audio Track 05
Computer
Monitor
Adjust the output level with
5
the STEREO fader and the
MONITOR/PHONES knob.
Using Rec Bus
Ex. 1: Use the Stereo Bus for monitoring the overall sound, and record specific channels
via the Rec Bus.
1. Set Rec Bus to ON for the channel(s) you wish to record via Rec Bus.
RECBUS (Recording Bus Assign) = ON (p. 99)
2. Assign the Rec Bus output to mLAN. (p. 90)
OUT PATCH (mLAN Out Channel): RECBUS = [1/2]
Ex. 2: For vocal recording, monitor the overall sound via the Stereo Bus and set up a
separate monitor mix for the vocalist (with STEREO/AUX OUT), recording the
microphone signal directly.
1. Set the Rec Bus output to ON for only those instrument channels you want in the
monitor mix for the vocalist.
2. OUT PATCH (St/Aux Out Port) : RECBUS = ST/AUX OUT (p. 91)
3. Apply reverb or other processing to the monitor mix as desired.
Set the Rec Bus of the STI 1 (in the Master layer) to ON. (See step #1 in Ex. 1 above.)
4. Record the microphone input directly. (See “Direct Recording” above.)
Quick Reference
Audio Playback from the Computer/Sequencer (DAW)
Stereo Playback (two-channel mix)
This setup lets you play back the main stereo output from the software mixer (DAW)
from the 01X.
Send the main stereo output of the sequencer to channels
Audio Sequencer
Software Audio Mixer
Computer
1
1 and 2 of the mLAN Audio Driver. (See step #8, p. 70.)
Set the mLAN 1 and 2 channels (Layer 9-16) to
2
stereo pair operation and adjust the level by
one of the faders.
1. Simultaneously press [SEL] of both mL1 and mL2.
2. Press knob 5 or 6 (RESET-BOTH). (p. 102)
01X
Effect 1, 2
Pan
Mix
Monitor
Ch. “mL2” (Layer 9-16)
EQ, Dyn, Vol
EQ, Dyn, Vol
Ch. “mL1”
SEND3, 4
Recording and Mixdown Using the 01X
This setup lets you use the 01X to mixdown the individual audio channels of the
sequencer (see application #2 at right) along with any live instruments/vocals input
to the 01X, and record everything to the sequencer. In this way, you can mixdown to
stereo two-track on your computer and master the recorded song in an audio editor.
Audio Sequencer
Software Audio Mixer
MIDI
Mic / Guitar
Synthesizer
Computer
Assign the output of the 01X Stereo Bus to mLAN. (p. 90)
OUT PATCH (mLAN Out Channel): ST-BUS = [1/2]
In this situation, direct recording of channels 1 and 2 (as in
“Direct Recording” on reverse side) is not possible.
mLAN Audio Driver Ch.1, 2
Effect 1, 2
SEND3, 4
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
STI1, 2
Pan
Mix
OUT PATCH
[ST-BUS] = D.OUT
<P.91>
Recorder
(Digital connection)
Monitor
Playback of Individual Channels
In this setup, each audio channel on the software mixer (DAW) is sent to the corresponding
channel of the 01X.
Audio Sequencer
Software Audio Mixer
Assign the audio channels on the
1
sequencer to the channels of
the mLAN Audio Driver, from
channel 1 in order. (p. 70)
Computer
Use the mLAN Stereo Inputs (Monitor In) for the sequencer’s stereo output.
2
• By connecting the stereo output of the sequencer to the mLAN Stereo Inputs,
you can monitor the both the sequencer output and the 01X output, without
having to use 01X input channels for monitoring.
• The available channels of the mLAN Audio Driver depend on the settings of
the mLAN Auto Connector. (Guide, pp. 9, 20)
01X
mLAN Stereo Input-R
Monitor A/B
mLAN Stereo Input-L
Ch. “mL8”
Ch. “mL7”
Ch. “mL6”
Ch. “mL5”
Ch. “mL4”
Ch. “mL3”
Ch. “mL2”
Ch. “mL1”
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
EQ, Dyn, Vol
SEND3, 4
The actual output settings differ depending on the sequencer (DAW).
For example:
• Each mixer channel on the sequencer is assignable to one of the mLAN channels.
• Each mixer channel on the sequencer is assigned to a bus, and the bus is
assignable to one of the mLAN channels.
Stereo L, R
Effect 1, 2
(Mix Balance)
Monitor
Pan
Mix
STI1, 2 Fader
WC96730 311POCP38.2-01A0 Printed in Japan
Loading...