Yaesu FT DX 9000 BROCHURE

Operator Interface: Visibility

The Total Operating Package

Technical Overview

From the moment you switch on the power of the FT DX 9000, you realize there is something special before you. The
information you need is right where your eyes are looking, and the display is not cluttered by extraneous data that is
confusing and fatiguing. It’s that " just right " feeling that lets you know that you own the very best.

Superior Visibility, with Logical and
Efficient Panel Layout

The FT DX 9000's front panel is uniquely operator­friendly. One's eyes are immediately drawn to
the center of the transceiver, where the most important
status and control operations take place. The large
main tuning dial is located just below the easy­to-read

frequency display, an area not cluttered
by information
Operator stress is
coupled with the two large, analog meters
immediately to the left of the frequency display.
Inthe"D" version, a 6.5 inch TFT display is provided,
which includes a real-time Spectrum Scope and
a host of operational status indicators.

other than frequency readouts.

reduced by the clean display,



Efficient Offset Tuning (Clarifier)

The oversized Clarifier control allowsoffset
tuningofthereceiverfromthemainoperating
frequency, for pile-up, contest, or even local
ragchewswhensomeoneisofffrequency.Green
andRedLEDsindicatewhethertheReceiveror
Transmitter, respectively, are being adjusted,
andtheamountofoffsetisclearlyindicatedin
themainfrequencydisplayfield.

Clear, Precise Analog Metering System

The huge 3.4" (86 mm) metering system provides
true analog precision and instant reaction time.





The left meter is a comprehensive TX/RX meter,
operating primarily as the "S-Meter" for the main
Receiver. The right meter is the S-Meter for the
Sub Receiver, and on transmit it serves as an ALC
Meter for the transmitter, allowing simultaneous
monitoring of ALC along with Power Output,
Compression Level, Microphone Input Level, PA
Current, or SWR on the left meter. On the "Contest"
and "MP" versions, two additional meters on the
right side of the front panel allow monitoring of
PA Voltage, Bias, SWR, and PA Temperature!

Large-Area TFT Status/information Display

Exciting display possibilities abound on the FT DX

9000. In addition to the "D" version's huge 6.5"
800 x 480 dot TFT display, the rear panel of the
FT DX 9000 includes a "Display" jack for connection
of an external monitor, if desired. The TFT
includes a number of status displays, including
band-swept SWR display, Spectrum Scope, and
multi-function World Clock. In the Spectrum
Scope mode, the entire TFT becomes the spectrum
display, for maximum viewing ease and resolution,
important for discerning weak signals in the
noise and interference on the band.
And if you connect your keyboard (not supplied)
to the rear panel keyboard jack, the TFT can
serve as a display screen for a station log.

Dual Metering and LCD Status Monitors
(Contest/MP Versions)



The two large analog meters to the left of the
frequency display provide a wide range of data
regarding operation on both receive and transmit.
But the two meters to the right of the frequency
display contain data not typically seen on Amateur
transceivers, including PA voltage, PA Temperature,
Bias Level, and SWR. The Bias may be adjusted
via a front panel control, with continuous alignment
possible between Class A and Class AB. In
addition, four oversized knobs allow precise
setting of the most important receiver filtering
adjustments:
CONTOUR,
Digital Noise
Reduction,
VRF, and
NOTCH

a

(manual).

Status Indication LEDs

Convenient indication LEDs are strategically
positioned near the knobs or function displays
associated with them, and in the case of the two
receivers the functions are easily separated due
to the Main Receiver being associated with Red
LEDs, and the Sub Receiver with Orange. The easy
recognition of functions and their status aids in
reducing operator stress over long hours of operation.

Panel Illumination

For ease of nighttime operation, the controls on
the front panel are indirectly illuminated, thanks
to carefully-positioned lamps in the frame underneath
the meters and TFT (depending on model).

When you and the transceiver become as one, the total operating experience becomes pure joy. You think, the radio does,

Superb Panel Layout for the HF Aficionado!

Many important control functions have been
brought out of the configuration menu and placed
on the front panel, per the requests of active operators
worldwide, and they're grouped in together for
instant access. For CW operation, controls such
as Pitch, Keyer Speed, CW Delay, and Keyer On/Off
are all closely grouped, while for SSB the VOX
Gain and Delay, Mic Gain, Processor Level, and
Compression Level metering controls are positioned
close together. And operations associated with
the Sub Receiver are all assembled in a special area
on the bottom left-hand side of the panel, so you
may use your left hand for feature selection and
your right hand for tuning of the Sub Receiver.
Both direct frequency entry and one-touch band
change are also provided, for efficient QSY.

and no other transceiver makes it so possible to realize!



Features Crafted for Real-World Operation

The Quick Memory Bank (QMB) remembers
frequency and mode data with one-touch Storage
and Recall capability. And the FT DX 9000 also
includes a valuable 30-second Digital Voice
Recorder that stores the incoming audio for the
most-recent 30-seond period, so you can go back
and review what was being received in case you
missed some important information during the
other station's transmission!

Smart Memory Card for Data/Configuration Storage

The Smart Memory Card (option on some versions)
allows storage, transfer, and recall of transceiver
configuration data and operator preferences, for
one-touch
environment. What's more, if you connect your
keyboard (not supplied) to the rear panel, you
can use the Smart Memory Card for storage of
Logbook data, that can later be transferred to a
personal computer for manipulation and archiving.

setup in a multi-operator DX-pedition

FT DX 9000 Contest;
Designed for the True Competitor!

If you're into contesting, you prize operating
efficiency, and that's why we created the FT DX
9000 "Contest" version. Intended for elite-class
DX-pedition and contest use, the FT DX 9000
Contest includes an extra Key and Headphone
jack, so two operators may use the transceiver at
the same time. Some of the "luxury" features of
the "D" and "MP" versions are available as add­on options, but you and your group can add



those later to configure your lean, mean contest
machine just the way you want to!



HF Cutting-Edge Transceiver

FT

DX

9000

Operation

Ergonomics

When your hand goes automatically to the right dial or switch on the front panel of a transceiver, you know that the
ergonomics have been carefully thought out by the design team. It is this kind of extra care that gives you the edge
during long operating sessions.

Touch the Main Dial, and You Know
the FT DX 9000 is Different. . .

The Main Tuning Dial is a large-diameter

•

(3.2"/81 mm) dial directly coupled to the magnetic
rotary encoder which drives the HRDDS via
microprocessor control. Its heavy weight (7 oz./200 g)
and quality mounting and construction provide a
smooth "flywheel" effect during operation, ideal
for quick cruising up and down a band.

The Main Tuning Dial is a new dual structure,

•

utilizing the normal dial structure along with a
rotating skirt that creates a small air gap. This air
gap reduces sweat accumulation on the operator's
fingertips, enhancing tuning precision during long
operating sessions, especially on DX-peditions to
hot tropical areas.

Ease of operation is further enhanced by the

•

convenient positioning of frequency-determining
switches immediately adjacent to the Main Tuning
Dial. VFO and Memory selection switches are
all located to the right, while the "Store" and
"Recall"
(QMB) memory
switches just to the left of the Main Tuning Dial.

switches for the Quick Memory Bank

registers are easy-to-spot blue

Three Large Knobs for Most
Important Control Functions

On the lower right-hand side of the front panel,
three large (1.5"/39 mm) knobs are provided for
several of the most often-used control operations.
The AF/RF Gain control utilizes high-quality,
concentric volume controls with the extreme
durability normally found on high-use test equipment.
The SHIFT/WIDTH controls utilize a carefully­specified dial tension, so as to ensure both ease and
precision in adjustment and stability of the settings.

To the right of the other two primary control knobs
is a "multi-function" knob that serves a number of
important purposes. Its most-often-used tasks
include VFO-B and Clarifier (offset) tuning, and
the large diameter makes precise tuning effortless.
When operating in the VFO-B mode, moreover,
this knob may be used for tuning in 500 kHz
steps (for quick "general coverage" band change),
as well as operating mode selection for VFO-B.
When operating in the "VFO-B" mode, the outer
circle lights up in orange, matching the color of
the VFO-B labels,
thus preventing
operator confusion
and errors.

Configuration Options!

Configure your FT DX 9000 for the Best Operating Experience. . .Your Way!

Although we've assembled an impressive array
of luxury features on the FT
versions, we have a deep respect for the individual
creativity of the users of our products. Low-band,
contest, DX-pedition, hi-fi audio, and local rag­chew specialists all have their particular needs,
and that's why we give you the ability to customize
your FT DX 9000 at the time of purchase, and
after purchase as well. The "Contest" version, with
addition of all options, becomes the "D" version.
Or you can custom-configure an intermediate version
to your liking.

For the latest Yaesu news,visit us on the Internet:

DX 9000 D and MP

You may select from among the following
options when placing your order:

Dual Receive Unit 

•

VRF Unit      

•

µ Tuning Units (1.8 MHz, 3.5/7 MHz, 10/14 MHz)

•

Memory Card Unit (Flash Memory)

•

TFT Unit (The Memory Unit is required for TFT operation)

•

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-ku, Tokyo 153-8644, Japan




http://www.vxstd.com

VERTEX STANDARD

US Headquarters

10900 Walker Street, Cypress, CA 90630, U.S.A.

About this brochure: we have made this brochure as comprehensive and factual as possible. We reserve the right, however, to make changes at any time in equipment, optional accessories,
specifications, model numbers, and availability. Precise frequency range may be different in some countries. Some accessories shown herein may not be available in some countries. Some

information may have been updated since the time of printing; please check with your Authorized Yaesu Dealer for complete details. This device has not been approved by the FCC. This device may
not be sold or leased, or offered for sale or lease, until FCC approval has been obtained.

http://www.vxstdusa.com
Email: [e-mail]

Phone [phone]; Fax [phone]

Customizing Options

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong

If the TFT Unit is to be installed at a later date (not
installed

at the time of original purchase), the
price changes, and an additional installation fee
may apply. See your Yaesu dealer for latest
pricing information.

http://www.yaesu.co.uk

Email: [e-mail]

http://www.vxstd.com.hk

2004.0905NA(U/E)

B9200468

Printed in Japan

Scheduled Introduction: December, 2004

Total Design Focus. . .

The Goal: Create the Greatest Transceiver Ever!

Then You Behold the Front Panel, and You Know. . .Yaesu Did It!

Future Production Model: FT DX 9000MP 400 W Version HF/50 MHz 

Dual Analog Meter Sets, LCD Display, Memory Card Installed, Main and Sub Receiver VRF, Full Dual RX,
Switching External Power Supply/Twin Speaker Enclosure.

FT DX 9000D 200 W Version HF/50 MHz

Large TFT Display, Built-in Memory Board, Main and Sub Receiver VRF, Full Dual RX,
"µ" Tuning (3 modules) Installed, Internal Switching Power Supply

FT DX 9000 Contest200 W Version HF/50 MHz

Dual Meters + LCD, VRF Installed in Main Receiver, Extra Key and Headphone Jacks, Internal Switching Power Supply

One Look, One Listen. . .

Actual Size Photo: "FT DX 9000D"

And you'll understand that the FT DX 9000 truly represents

A New Dimension in Amateur Radio!