XPiQ inc PM200-14B, PM200-14C, PM200-16B, PM200-16C, PM200-18B Datasheet

200 Watts

PM200 Series

4000 VAC Isolation

•

100% Burn-in

•

Low Safety Leakage Current

•

Short Circuit Protection

•

Meets EMI Requirements of

Medical Equipment

•

Both Line and Neutral Fused for

European Requirements

•

•

•

Specification

All specifications typical at nominal line, full load and 25°C

Intelligent Design Quality Product

XPiQ inc.

Medical Switching Power Supply

Input

Input Voltage • 90 to 130 VAC or 180 to 264 VAC

autoranging
Input Frequency • 47 to 440 Hz
Input Current • 4.5A (rms) for 115 VAC

2.6A (rms) for 230 VAC
Safety Ground • 50µA max. at 110 VAC 60 Hz
Leakage Current • 100µA max. at 240 VAC 50 Hz

Output

Total output power: • 15 to 200 watts
Ripple and noise: • 2% peak to peak maximum
Overvoltage • Provided on output #1 only;

Protection: set at 112-132% of its nominal

output voltage

Overcurrent • All outputs protected to short
Protection: circuit conditions

Temperature • All outputs ±0.04%/°C
Coefficient: maximum

Transient Response: • Maximum excursion of 4% or

better on all models, recovering
to 1% of final value 500us after
a 25% step load change

Line Regulation • ±0.5% max. at full load

General

Efficiency • 70% minimum at 200 watt output
Hold-up time • 20 msec minimum at nominal input
Inrush Current • 60A max at 25°C cold start
Withstand Voltage • 4000 VAC from input to output

1500 VAC from input to ground
500 VAC from output to ground

Environmental

Operating • 0°C to +70°C*
Temperature

Storage • -40°C to +85°C
Temperature

Relative Humidity • 5% to 95% non-condensing
MTBF • 85,000 hours minimum at full load

at 25°C ambient

EMI Requirement • Meets the conducted limits of

EN 55011 (CISPR11) Level B

Safety Requirements • Approved to: (Not for patient

contact)
a) UL2601
b) CSA C22.2 No.601.1-M90 per CUL
c) IEC 601-1/EN60601-1 (per TUV)

* Derate linearly from 100% load at 50°C to 50% load at 70°C

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XP-iQ.com

157

145-166 1/5/02 11:12 am Page 13

Connectors P1 P2 P3
Model 1 2 3 1, 2 3, 4, 5 6 7 8 9 1 2 3 4
PM200-10 PM200-12 AC AC AC Output Output Output Common Common
PM200-13 PM200-14 Line Neutral Ground -Sense Return #I #I #1 +SENSE PFD RETURN RETURN FAN
PM200-16 PM200-18
PM200-23 PM200-24 AC AC AC Output Common Output N.C. N.C. N.C. PFD Common Common FAN
PM200-25 Line Neutral Ground #1 Return #2 Return Return
PM200-30 PM200-31 AC AC AC Output Common Output Output N.C. N.C. PFD Common Common FAN
PM200-32 Line Neutral Ground #1 Return #2 #3 Return Return
PM200-40 PM200-41 AC AC AC Output Common Output Output Output Output Common Common
PM200-42 Line Neutral Ground #1 Return #2 #3 #4 #4 PFD Return Return FAN
PM200-45 Return

OUTPUT VOLTAGE & CURRENT RATINGS PM200

Notes

•

Mechanical Details

Pin Chart

Notes:

1. Dimensions shown in inches (mm)

2. Tolerance 0.02 (0.5) maximum)

3. Input connector P1 is Beau Inc. P/N 72-5-03C.
Output connector P2 is Beau Inc. P/N 72-5-09C.
Screws are #6-32 on 0.375 inch centers.

4. Connector P3 mates with Molex housing 22-01-1043
and Molex 40445 series crimp terminal

5. Weight: 1.4 Kgs (3.10 lbs) approx. for “B” version

1.75 Kgs (3.90 lbs) approx. for “C” version

Output #1 Output #2 Output #3 Output #4 Maximum

Output

Model Vnom Imin Imax Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Vnom Imin Imax Tol. Power

2

PM200-10 5 V 3.0 A 40.0 A 2% 200 W
PM200-12 12 V 1.2 A 16.7 A 2% 200 W
PM200-13 15 V 1.0 A 13.0 A 2% 200 W
PM200-14 24 V 0.6 A 8.4 A 2% 200 W
PM200-16 30 V 0.5 A 6.7 A 2% 200 W
PM200-18 48 V 0.3 A 4.2 A 2% 200 W
PM200-23 +5 V 3.0 A 30.0 A 2% +12 V 0 A 8 A 4% 200 W
PM200-24 +5 V 3.0 A 30.0 A 2% +15 V 0 A 6 A 4% 200 W
PM200-25 +5 V 3.0 A 30.0 A 2% +24 V 0 A 4 A 4% 200 W
PM200-30 +5 V 3.0 A 30.0 A 2% +12 V 0 A 8 A 4% -5 V 0 A 6 A 4% 200 W
PM200-31 +5 V 3.0 A 30.0 A 2% +12 V 0 A 8 A 4% -12 V 0 A 4 A 4% 200 W
PM200-32 +5 V 3.0 A 30.0 A 2% +15 V 0 A 6 A 4% -15 V 0 A 4 A 4% 200 W
PM200-40 +5 V 3.0 A 30.0 A 2% +12 V 0 A 8 A 4% -12 V 0 A 4 A 4% F 5 V 0 A 6 A 4% 200 W
PM200-41 +5 V 3.0 A 30.0 A 2% +15 V 0 A 6 A 4% -15 V 0 A 4 A 4% F 24 V 0 A 4 A 4% 200 W
PM200-42 +5 V 3.0 A 30.0 A 2% +12 V 0 A 8 A 4% -12 V 0 A 4 A 4% F 12 V 0 A 4 A 4% 200 W
PM200-45 +5 V 3.0 A 30.0 A 2% +12 V 0 A 8 A 4% -12 V 0 A 4 A 4% F 24 V 0 A 4 A 4% 200 W

1. Add suffix "B" for U-bracket or "C" for enclosed form e.g. PM200-45C.

2. Peak current is 12A on +12V, 9A on +15 V, and 6A on +24V.

3. Output #4 is floating. It can be connected externally for positive or negative output.

4. 200 watts for "C" version with a cover-and-fan assembly. 150 watts for "B" version without moving air.
(max current of output #1 & #2 derated to 70%) or 200 watts (no derating) with 25 CFM forced air provided by user.

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XP-iQ.com

158

145-166 1/5/02 11:12 am Page 14