EN
Topic:
i
Multimedia & Navigation System
with Android™ 6.0 OS
Installation manual
Thank you for purchasing one of our products with Android 6.0.1!
We appreciate your condence. Enjoy your brand new multimedia unit!
XM-2DA703-A6
Please read the following manual carefully before you install and use the
unit. Please save this manual in case you will need to clarify fur ther possible
questions regarding installation and usage of our product.
We recommend you to let the technician install the unit in your vehicle.
You can nd the detailed manual for your product on our homepage:
www.xomax.de/download
ENGLISH
1
EN
Topic:
Table of Contents
Table of Contents
Safety instructions and precautions 3
Handling by stop only ...................... 3
Installation .................................... 3
Regular loudness ............................ 3
Repair of the unit............................ 3
Power supply ................................. 3
Replacement of fuses ...................... 3
Overheating ................................... 3
Regular temperature ....................... 3
Cleaning of the unit
Usage of the touchscreen ................ 4
Moisture ........................................ 4
The risk of injuries .......................... 4
Handling the CDs and DVDs ............. 4
Installation 5
Connection schedule Can-Bus
cable adapter 7
........................ 4
Quadlock cable connections 8
Connection schedule – Cinch
multicore 9
Common solutions 10
Recycling of an old unit 12
Recycling of the battery 12
2
EN
Topic:
Safety instructions and precautions
Safety instructions and
!
!
!
!
!
!
!
!
!
precautions
Handling by stop only
To avoid any accidents please don't
handle the unit while you driving. Please
stop and park the vehicle at safety
place and handle the unit casually.
Installation
Please read the following manual
carefully before you install the unit. We
recommend you to let the technician
install the unit in your vehicle.
Regular loudness
Please set the loudness of the unit to
the appropriate level so you were still
able to hear exterior noises especially
trafc warning signals. Furthermore the
higher loudness level can damage your
hearing organs.
Repair of the unit
Due to awed warranty seal the
warranty becomes invalid.
Power supply
Use the unit connected only to 12 Volt
on-board power supply. The minus (-)
should be connected with the ground
(GND) (negative).
Due to the wrong conguration exists
the danger of re. In case of doubt
please consult with professional technicians.
Replacement of fuses
While replacing the fuse please make
sure that the new fuse has the same
properties as the old one, especially the
amperage.
Overheating
Do not occlude the vent holes to avoid
the heat generation and accumulation
in the unit. Otherwise exists the danger
of re.
Do not open the unit. Do not try to
repair the unit by yourself due to any
emerging technical problems. While
opening the unit by yourself exists the
danger to be electrocuted.
Do not use the unit any further since
you detect any kind of technical
problems.
Leave all the repair operations to
professional technicians.
Regular temperature
Please make sure that the temperature
inside of the vehicle amounts to not
more than +40 C.
If it's too cold or too hot inside of the
vehicle, do not turn the unit on until
the inside temperature of the cabin
descends.
3
EN
Topic:
Safety instructions and precautions
!
Cleaning of the unit
!
!
!
!
!
Please keep the unit clean and remove
the dust from it regularly. Please use for
that a soft and dry cleaning rag.
Major soilings can be removed carefully
with the wet cleaning rag. Do not use
any chemical or alcohol-containing
detergents to avoid the damage of the
unit's varnish.
Usage of the touchscreen
Do not press the touchscreen too hard
– it may lead to image distortions, unit
malfunctions and touchscreen damages.
Do not use any sharp articles to use
the touchscreen. Please handle the
touchscreen with your nger or with the
appropriate stylus.
Moisture
To avoid the danger of re or the
electric shock do not put the unit in to
the moist environment (e.g. adverse
weather conditions, inappropriate wet
cleaning etc.)
Handling the CDs and DVDs
Remove transport securing
screws (if available)
Before using the optical drive, be
sure to remove the two transpor t
locking screws marked with colored
stripes (top of the radio).
The risk of injuries
Do not open the cabinet or modify the
unit. The active laser components used
with this product comply with the
provisions of Laser Class 1.
4
EN
Topic:
Installation
Installation
!
!
We recommend you to let a
professional technician install the
unit in your vehicle.
WARNING!
Please read these advices carefully
before installation procedure.
The damages caused by an inappropriate installation are not covered
by warranty.
To avoid the risk of losing the
warranty please let a specialist
accomplish the installation of the
unit.
» To avoid a short circuit please
disconnect the vehicle battery before
the installation. To do it properly please
read the manual of the vehicle.
» Please be aware that this unit has an
2DIN standart size. Make sure that your
vehicle is equipped with an installation
cell of required size.
» As may be the case you will need a
suitable faceplate, adapter or other
accessories. These could be provided
from your local specialist supplier.
» The connection cables may not be
cutted or short-circuited. Otherwise the
warranty becomes invalid.
» Before the installation please make
sure that the vehicle has the 12 Volt
on-board power supply.
» The minus (-) should be connected
with the ground (GND) (negative).
» Please tag the polarity of the avai-
lable speakers before you disconnect
the vehicle batter y.
» A proper grounding of the unit's
housing requires a clean ground
connection. Thus the grounding area
should be rust-, stain- and dust-free.
» Please ground the cable separately
from other heavy current devices such
as an amplier etc.
» Please ensure that the coloured
cables are connected according to the
wiring diagram. The wrong wiring may
lead to malfunctions or even damages
of the electric elements of the vehicle.
» Please note that the connection
cables of this unit and of the other
devices may have the same purpose
but the different colour. For this reason
while connecting this unit with the
other devices please ensure that both
of the cables in each case have the
same purpose. To congure everything
correctly please refer to the manuals of
the both devices.
» Please ensure that the negative
speaker cable is in each case plugged
into the negative speaker socket of the
ISO interface. Do not ever connect the
negative speaker cables with the vehicle
body.
» This unit is designed and construed
for connection with 4 speakers. Do not
combine this unit with devices that are
designed and construed for connection
5
EN
Topic:
Installation
with 2 speakers.
» The speakers should feature the
impedance of 4-8 Ohm and a sufcient
wattage.
» Please ensure that the speakers you
are connecting with the unit are intact.
Damaged speakers can impair the unit.
» To avoid a short circuit please isolate
all cable junctions and endings of the
unused cables with the electrical tape.
» All the cables should be layed and
xated tidy and properly. The cables
should not contact any movable or hot
objects.
» If the vehicle doesn't have an "ACC"
ignition position, please connect the
red cable with the ignition switch.
Otherwise the unit does not turn off
automatically, causing the discharging
of the vehicle battery.
» To avoid a rogue and hazardous
short circuit do not lay the yellow cable
through the engine bay in order to
connect it with the vehicle battery.
» Do not ever connect speaker cables
among one another. In case you do not
want to connect all the 4 speakers with
the unit please isolate the endings of
unused cables with the electrical tape
to prevent a short circuit.
» Do not ever connect the negative
speaker cables with the vehicle body.
» To ensure a awless performance of
the unit the intergration angle should
amount to +/- 30.
6
EN
Topic:
Connection schedule Can-Bus cable adapter
Connection schedule Can-Bus cable adapter
7
EN
Topic:
Quadlock cable connections
Quadlock cable connections
8
EN
Topic:
Connection schedule – Cinch multicore
Connection schedule – Cinch multicore
9
EN
Topic:
Common solutions
Common solutions
The following advices are generally valid and refer to diverse Xomax models with
the similar characteristics. Please note that some articles may refer not to your
model exactly and contain the describtion of features and functions that your model
does not support.
The describtion of the
problem
The remote control is
without function.
The unit does not turn
on.
The cause and the solution
Solution 1:
Please ensure that the bat tery lm is removed. By
deliver y the bat tery is protected by a lm which should
be removed befor e usage.
Solution 2:
The bat tery could be empty. Please replace it if required.
Solution 3:
Please make sure that the infrared receiver (labelled with
IR) on the control panel is not blocked.
Not e:
You can test the functionality of the remote control as
follows: please hold the IR transmitter towards a c amera
(e.g. a cell phone camera) and press any button on the
remote control. If the remote contr ol is operative you
can see the infrared signal on the display of the used
camera device.
This problem is in most cases caused due to a wrong
connection of the ISO cable.
Please review the pin assignments of the ISO cable and
ISO plug. Pay attention to the proper connection of the
ignition- and steady plus and correct the discrepancy if
required.
Not e:
Though the design of ISO plug is standar dized, it's pin
assigment is not and may vary. Thus in case of mismatch
of connections due to different pin assignments a simple
plug'n'play connection may lead to grievous error s.
10
EN
Topic:
Common solutions
Poor radio reception:
The radio tuner nds no
broadcaster or the reception is poor.
For problem-solving regarding the radio reception it
is impor tant to know the type of the antenna of your
vehicle.
Here are the possible solutions for each t ype of the
antenna:
Type 1 – passive antenna:
We recommend you to substitude the existing antenna
by the larger and therefore more ef cient one.
Shark n or r od antennas (under 5 cm) are denitely
insufcient.
Type 2 – active antenna:
The vehic le provides no cur rent for the active antenna.
In this case a phantom power is required, which provides
the active antenna with the ex ternal power supply.
Type 3 – active antenna with diversity system:
The unit provides no current for the active antenna and
has no diversity suppor t. For this type of antenna is
required the phantom power with an integrated diversit y
system.
Not e:
A phantom power is not to be confused with an antenna
amplier which is far less ef cient.
Radio stations are lost:
As soon as the unit will be
turned off all the stored
stations and users settings
will be lost.
This problem is c aused due to a wrong connec tion of the
ISO cable.
Please interchange the cables for ignition plus and for
steady plus.
Caution:
If these wires have fuses the latter should be interchanged as well.
11
EN
Topic:
Recycling of an old unit
Recycling of an old unit
User information regarding recycling of
electric and electronic devices (private
households)
This symbol on products or in their
manuals implies that electric and
electronic devices at the end of their
service life should be separated from
the domestic waist.
Please hand these products for recycling at municipal collection points free
of charge.
The proper disposal of these products
contributes to environment protection.
To nd the nearest collection point
or recycling yard please consult your
municipal administration.
Recycling of the battery
According to the battery decree we
make you aware of your obligation to
dispose of empty batteries at municipal
collection points.
Batteries that contain pollutants
(e.g. Hg = mercury, Pb = lead, Cd =
cadmium) are labelled with the symbol
pictured above.
At our place you can free dispose of the
empty batteries purchased at our store.
Made for STEL Multimedia GmbH,
Paewesiner Weg 20,
13581 Berlin,
GERMANY
12
Loading...