Safety Plate (SP-1) for Sine
Installation
Instruction Sheet
Wave Plus AC/DC Conduit
Boxes
Safety Plate Overview
The purpose of the Safety Plate (SP-1) is to prevent accidental contact
with any live circuits or wires within either the DC Conduit Box (DCCB)
or the AC Conduit Box (ACCB). The Safety Plate (SP-1) covers the open
end of either the DCCB or the ACCB on the inverter side. It attaches to
the base of the conduit box and is secured by the Sems screws that attach
the top cover. The Sems screws have lockwashers attached and are used
on the top and bottom of the top covers. The Safety Plate only needs to be
installed in the event that the Sine Wave Plus inverter is removed from the
system.
SP-1 Safety Plate
975-0081-01-01 Rev A
Figure 1-1
975-0081-01-01 1 of 4
Safety Plate SP-1
Safety Plate (SP-1) for Sine Wave Plus AC/DC Conduit Boxes
Installing the Safety Plate
WARNING: Shock Hazard
Be sure to disconnect all DC and AC power before
removing the inverter and installing the safety plate.
To install the safety plate:
1. Remove the two #8 Sems screws on the top and bottom of the conduit
box (AC or DC). Put these screws is a safe place.
2. Slide the Safety Plate over the open end of the conduit box inserting
the cover tabs into the slots on the Safety Plate. Be sure to align the
holes for the screws for resecuring the top cover.
3. Replace the two #8 Sems screws on the top and bottom of the chassis
to secure the Safety Plate into place.
Remove these Sems Screws
only from the top cover
Inverter side of
ACCB and DCCB
Cover Tabs
AC Conduit Box (ACCB)
Figure 1-2
Location of Cover Tabs and #8 Sems Screws on Top Cover of AC and DC
Remove these Sems Screws
only from the top cover
DC Conduit Box (DCCB)
Conduit Boxes.
2 of 4 975-0081-01-01
Top Cover
Installing the Safety Plate
x
o
B
t
i
u
d
n
o
C
C
D
X
E
R
T
N
A
X
Safety Plate
Replace the #8 Sems
screw from the top of
the chassis.
Figure 1-3
Installing the Safety Plate SP-1 on the DCCB
Top Cover
Ensure the top cover tabs
protrude through the
cover tab slots.
x
o
B
t
i
u
d
n
o
C
C
D
X
E
R
T
N
A
X
Replace the #8
Sems screw from
the bottom of the
chassis.
NOTE: Installation of the Safety Plate
on the ACCB is the same as shown in
this illustration for the DCCB.
975-0081-01-01 3 of 4
Safety Plate (SP-1) for Sine Wave Plus AC/DC Conduit Boxes
Trademarks
SP-1 Safety Plate is a trademark of Xantrex International. Xantrex is a registered trademark of Xantrex
International.
Other trademarks, registered trademarks, and product names are the property of their respective owners
and are used herein for identification purposes only.
Notice of Copyright
Safety Plate (SP-1) for Sine Wave Plus AC/DC Conduit Boxes © August 2003 Xantrex International.
All rights reserved.
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC.
(“XANTREX”)
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF
ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER
DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER
DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF
THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE
ENTIRELY AT THE USER’S RISK.
Date and Revision
August 2003 Rev A
Part Number
975-0081-01-01
Contact Information
Telephone: 1-800-670-0707 (toll free in North America)
1-360-435-8826 (direct)
Fax: 1-360-435-3547
Email: CustomerService@xantrex.com
Web: www.xantrex.com
4 of 4 975-0081-01-01
Loading...