World Dryer K-162 Service Manual

SMARTdri

™

High-Efciency Intelligent Hand Dryer

Secamanos inteligente altamente eciente

Sèche-mains intelligent à haute efcacité

All K and K4 Series

Todos los modelos K y de la Serie K4
Ensemble de la série K et K4

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or service
the product described. Protect yourself and others by observing all safety information. Failure to comply with
instructions could result in personal injury and/or property damage. Retain instructions for future reference.

Por favor lea y guarde estas instrucciones. Léalas cuidadosamente antes de tratar de montar, instalar, operar o dar mantenimiento al producto aquí
descrito. Protéjase usted mismo y a los demás observando toda la información de seguridad. No seguir las instrucciones puede ocasionar daños, tanto
personales como materiales. Guarde estas instrucciones para referencia en el futuro.

Lire et conserver ces instructions. Les lire attentivement avant de commencer à assembler, installer, faire fonctionner, réparer ou entretenir l’appareil
décrit. Pour se protéger et protéger autrui, observer toutes les consignes de sécurité. Le fait de négliger d’appliquer ces instructions peut entraîner des
blessures et/ou des dommages matériels. Conserver ces instructions pour consultation ultérieure.

World Dryer Corporation

5700 McDermott Drive
Berkeley, IL 60163 U.S.A.
800-323-0701
www.worlddryer.com

1

Description

World warm air hand dryer, powered by a universal brush motor, delivers up to 850 watts of drying power and incorporates
an integrated element for heated air. The dryer controls provide for (3) distinct levels of motor operation (Hi, Med and
Low) and the option of operation with, or without, the heating element. An infrared sensor is used to automatically activate
the dryer. These models are intended for use in commercial, industrial, ofce and public facility environments.

Electrical Specications

Table 1

Models Type Electrical Input Rated Amperage Rated Watts Certications

K-XXX Automatic 120VAC, 50/ 60Hz 10A 1200 UL

K4-XXX Automatic 208 - 240VAC, 50/60Hz 5.2A 1250 UL

General Safety Information

DANGER Failure to disconnect the power source before installation or servicing can result in serious

injury or death from electric shock.

• Always disconnect the power source before servicing or installing the hand dryer.

DANGER Failure to properly ground this unit could result in severe electrical shock and/or death.

• This hand dryer must be properly grounded (Earthed) for safe operation. An identied ground connection point is
supplied on the hand dryer’s wall base.

• We recommend GFCI protection in wet or damp locations or as required by local code.

WARNING Risk of re, personal injury or property damage are possible if local codes, or safety

recommendations are not followed.

• Installation and servicing should only be performed by qualied electrical technicians.

• Use only the electrical power (voltage and frequency) specied for the model hand dryer being installed. See Table 1 ­Electrical Specications.

• Connect the hand dryer to the nearest suitable distribution panel.

• To limit a voltage drop, and insure efcient operation, use No. 12 AWG (4 mm2) wire or larger as required by local
electrical codes.

• Always connect to a branch circuit with circuit breaker or fuse protection with an electrical rating greater than the model
hand dryer’s rated amperage shown in Table 1 - Electrical Specications in accordance with the NEC (National Electrical
Code) and/or CEC (Canadian Electrical Code).

• To avoid a hazard due to inadvertent resetting of the thermal cutout, the hand dryer must not be supplied through an
external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

• Each automatic model hand dryer must have a dedicated circuit.

• Route all eld wiring away from moving parts within the hand dryer.

CAUTION Improper mounting could result in personal injury or property damage.

• Follow the mounting height recommendations in Table 2.

• On a stud wall, one side of the hand dryer should be mounted to an existing stud.

Unpacking

1. Remove all packing material. Recycling is recommended.

2. Carefully remove the hand dryer from the shipping carton, using care not to drop the appliance.

3. Inspect carefully for any damage that may have occurred during transit. Check for any loose, missing or damaged

parts. If the hand dryer is damaged, promptly inform the dealer where you purchased it.

2