World Dryer B2512168 User Manual

VMax® V2

High-Speed Vertical Hand Dryer

Secamanos vertical de alta velocidad • Sèche-mains vertical haute vitesse

V-649A

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or service the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage. Retain instructions for future reference.

Por favor lea y guarde estas instrucciones. Léalas cuidadosamente antes de tratar de montar, instalar, operar o dar mantenimiento al producto aquí descrito. Protéjase usted mismo y a los demás
observando toda la información de seguridad. No seguir las instrucciones puede ocasionar daños, tanto corporales como materiales. Guarde estas instrucciones para referencia en el futuro.

Lire et conserver ces instructions. Les lire attentivement avant de commencer à assembler, à installer, à faire fonctionner ou à entretenir l’appareil décrit. Pour se protéger et protéger autrui,
observer toutes les consignes de sécurité. Négliger de se conformer à ces instructions peut causer des blessures personnelles et/ou des dommages matériels. Conserver ces instructions
pour références ultérieures.

World Dryer Corporation

340 County Line Road
Bensenville, IL 60106 U.S.A.
800-323-0701
www.worlddryer.com

68-10467

Description

World air hand dryer is a surface-mounted dryer powered by a brushless DC motor, and delivers 1000 watts of drying
power. The dryer incorporates a replaceable HEPA filter and replaceable odor neutralizing tablet. An infrared sensor is
used to automatically activate the dryer. These models are intended for use in commercial, industrial, office and public
facility environments.

Electrical Specifications

Table 1

Models Type Electrical Input Rated Amperage Watts Certifications

V-649A Automatic 120V, 60 Hz 10 A 1000

General Safety Information

DANGER Failure to disconnect the power source before installation or servicing can result in serious injury or death from electric shock.

• Always disconnect the power source before servicing or installing the hand dryer.

WARNING Risk of fire, electric shock, personal injury or property damage are possible if local codes, or safety recommendations are

not followed.

• Use only for drying hands as intended by the manufacturer. Do not use hand dryer for any purpose other than drying hands.

• Carefully follow all instructions for installation on the enclosed mounting template / instructions.

• Installation should only be performed by qualified persons in compliance with all applicable national and local codes and standards.

• When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

• Always connect to a branch circuit with circuit breaker or fuse protection with an electrical rating greater than the model hand dryer’s rated

amperage shown in Table 1 - Electrical Specifications in accordance with national and local electrical codes.

• Use only the electrical power (voltage and frequency) specified for the model hand dryer being installed. See Table 1 - Electrical

Specifications

• To limit a voltage drop, and insure efficient operation, use 14 AWG wire or larger as required by local electrical codes.

• Each hand dryer must have a dedicated circuit.

• For indoor use only. Do not use outdoors. Do not expose to rain, sun or extreme temperatures. Do not use near sources of water or

extreme heat.

• Repair work should only be performed by an authorized service representatives.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack

of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.

WARNING Risk of fire, electric shock, personal injury or property damage are possible if the following safety precautions are not

followed.

• Do not use hand dryer for any purpose other than drying hands.

• Repair work should only be performed by an authorized service representatives. Only use genuine replacement parts.

• Do not insert foreign objects in or on the unit.

• Do not place heavy objects on the unit.

• Do not use in corrosive environments.

• Do not use in explosive atmospheres.

• Do not use in extremely humid locations or near sources of water.

• Do not immerse appliance in water or other liquid.

• Children should be supervised not to play with the appliance.

• Disconnect from the power supply before servicing.

WARNING When you dispose of an old appliance or any components, follow any local and national laws on disposal of electronic

waste. This appliance must not be disposed together with the domestic waste. This appliance has to be disposed at an authorized place
for recycling of electrical and electronic appliances. By collecting and recycling waste, you help save natural resources, and make sure
the product is disposed in an environmental friendly and healthy way.

WARNING Cancer and Reproductive Harm - www.p65warnings.ca.gov

English

2

Unpacking / Standard Accessories

1. Remove all packing material. Recycling is recommended.

2. Carefully remove the hand dryer from the shipping carton, using care not to drop the appliance.

3. Inspect carefully for any damage that may have occurred during transit. Check for any loose,
missing or damaged parts. If the hand dryer is damaged or missing parts, promptly inform the
dealer where you purchased it.

Standard items included with the hand dryer are:

Power Supply

Cleaning Brush

User Manual

Manual

Installation Template

Cover Kit

HEPA Filter Cartridge with Odor

Neutralizing Tablet

Installation

CAUTION Improper mounting could result in personal injury or property damage.

1. Use the mounting template provided to mark the locations for the (4) wall

mounting anchors to attach the wall mounting bracket to the wall.

2. It is recommended that at least 1 of the 4 mounting anchors for the unit be

fastened into a wall stud or support.

3. To use the hollow wall anchors included with the wall mounting kit, pre-drill the

wall in the marked locations using a 5/16” (8mm) drill, insert the plastic anchors
and tap flush to the wall.

4. Complete the attachment of the wall mounting bracket to the wall with the (4)

mounting anchors using a No. 25 torx screwdriver.

5. Hang the hand dryer on the bracket. Remove water collection tray from bottom

of dryer, and complete the attachment of the dryer with the 4th anchor.

6. Connect power supply wiring to terminal block and secure Power Supply Cover

7. Replace the water collection tray.

3 English

Wall Mounting Bracket with

mounting anchors

How to Use

1. The hand dryer will start automatically when hands are inserted.

2. Slowly move your hands up and down through the air stream for 10 – 12 seconds.

3. The hand dryer will stop automatically after hands are removed.

Dryer Controls

The hand dryer is equipped with an ON/OFF Power Switch and Speed Control Switch for quieter operation if desired.
The factory setting for the Speed Control Switch is “HIGH”. Both the ON / OFF Power Switch and Speed Control Switch
are located inside the dryer - above the water collection tray. To access, remove the water collection tray and intake air
pre-filter and locate the ON / OFF Power Switch and Speed Control Switch as shown in the figure below.
Note: The hand dryer includes an anti-vandal lock for securing the water collection tray and HEPA filter. The lock is
located immediately below the water collection tray. To remove the water collection tray or HEPA filter, slide the lock to the
right to the “unlocked” position. After servicing, slide the lock to the left to the “locked” position.

LED Display

The LED display provides information about the operation and
servicing needs of the hand dryer.

• LED-1: Starting operation: (Mode 1) LED-1 a blue “smiley” icon appears 3 times. Afterwards

the LED lights rotate clockwise for 9 seconds (one drying cycle), thereafter all 30 LEDs blink
3 times. The LEDs rotate again and flash after 9 seconds. Afterwards the machine shuts off
automatically. (Mode 2) Same as above, but the LEDs rotate clockwise for 10 seconds. In
case of an electrical or motor problem all 30 LEDs will blink for 30 seconds.

• LED-2: Filter change sign. The filter sign will turn on after 25.000 uses. After replacing the

filter the filter sign will stay for 5 seconds, and then blink 3 times (the filter usage is reset).

• LED-3: Shows that the water tank is full. When full the water tank will blink red until the water

is emptied and the tray is put back into the unit.

Maintenance and Cleaning Instructions

Cleaning

• All surfaces of the hand dryer can be cleaned with a soft cloth and non-abrasive, non-caustic cleaning solution.

• Provided cleaning brush should be used for cleaning the drain hole in the bottom of the drying cavity.

Maintenance

Emptying the Water Collection Tray

1. The water collection tray will fill with water with hand dryer use.

2. Regularly check the water tank status on the LED display panel. The LED Display will indicate when the water
collection tray is full and needs emptying.

3. If water collection tray is not emptied when full, the collection tray will overflow onto the floor. High washroom traffic
may require more frequent emptying of the water collection tray.

4. For optimum hygiene, routinely clean the water collection tray with a non-abrasive, non-caustic cleaning solution.

English

4