Woods Equipment S20CD, S15CD, S22CD, S25CD, S27CD User Manual

Download

Page 1

FLAIL

SHREDDER

Center Drive

S15CD S20CD S22CD S25CD S27CD

(Rev. 11/8/2011)

MAN0506

Page 2

TO THE DEALER:

Assembly and proper installation of this product is the responsibility of the Woods and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner.

The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Please contact your dealer to complete this form. Dealers can register all Woods product at dealer.WoodsEquipment.com under Product Registration.

Failure to register the product does not diminish customer’s warranty rights.

TO THE OWNER:

Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment.

For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary tools and equipment to handle all your needs.

Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided:

dealer. Read manual instructions

Model: _______________________________ Date of Purchase: _____________________

Serial Number: (see Safety Decal section for location) ____________________________________

Provide this information to your dealer to obtain correct repair parts.

Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety.

2 Introduction

Gen’l (Rev. 3/5/2010)

Page 3

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

BALANCE STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12

OPERATOR SIGN-OFF RECORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

FIELD OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

OPTIONAL EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

SHREDDER STORAGE & CLEANING. . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

SERVICE & MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

CONTOUR FLAIL PATTERN WORKSHEETS . . . . . . . . . . . . . . . . . . . . . . .36

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

DEALER CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

INDEX TO PARTS LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .64

INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . INSIDE BACK COVER

LEA EL INSTRUCTIVO!

Si no lee Ingles, pida ayuda a

alguien que si lo lea para que le

traduzca las medidas de seguridad.

MAN0506 (Rev. 9/5/2008)

Introduction 3

Page 4

SPECIFICATIONS

Maximum Outside Body Width:

15′ . . . . . . . . . . . . . . . . . . 189 in. (4.9 m)

20′ . . . . . . . . . . . . . . . . . . 253 in. (6.4 m)

22′ . . . . . . . . . . . . . . . . . . 277 in. (7.0 m)

25′ . . . . . . . . . . . . . . . . . . 309 in. (7.8 m)

27′ . . . . . . . . . . . . . . . . . . 334 in. (8.4 m)

Cutting Height: . . . . . . . . . . . . . . . . . . . . 3 - 18 in. (7.62 cm to 45.7 cm)

Width of Cut:

15′ . . . . . . . . . . . . . . . . . . 183 in. (4.6 m)

20′ . . . . . . . . . . . . . . . . . . 247 in. (6.2 m)

22′ . . . . . . . . . . . . . . . . . . 271 in. (6.8 m)

25′ . . . . . . . . . . . . . . . . . . 303 in. (7.6 m)

27′ . . . . . . . . . . . . . . . . . . 327 in. (8.3 m)

Knives: Cups

Number on 15′ . . . . . . . . . . . . 84. . . . . . . . . . . 164. . . . . . . . . . . . 4

Number on 20′ . . . . . . . . . . . . 116 . . . . . . . . . . 228. . . . . . . . . . . . 4

Number on 22′ . . . . . . . . . . . . 128. . . . . . . . . . 252. . . . . . . . . . . . 4

Number on 25′ . . . . . . . . . . . . 144. . . . . . . . . . 284. . . . . . . . . . . . 4

Number on 27′ . . . . . . . . . . . . 156. . . . . . . . . . 308. . . . . . . . . . . . 4

Recommended Tire Size: . . . . . . . . . . . . 9.5L - 15,6 ply rated

Tire Inflation Pressure: . . . . . . . . . . . . . . 25 psi

Rotor: Speed . . . . . . . . . . . . . . . . . . . . . 1350 RPM dynamically balanced

Drive: PTO . . . . . . . . . . . . . . . . . . . . . . . 1000 RPM

Weight of Shredder (approximate):

15′ w/2 casters* . . . . 3600 lbs (1633 kg)

20′ w/4 casters* . . . . 4800 lbs (2177 kg)

“L” “L” Cut-Off

4 Introduction

22′ w/4 casters* . . . . 5100 lbs (2313 kg)

25′ w/4 casters* . . . . 5600 lbs (2540 kg)

27′ w/4 casters* . . . . 5900 lbs (2676 kg)

* each caster assembly weighs

approximately 214 lbs

MAN0506 (Rev. 9/5/2008

Page 5

IMPORTANT!

WARNING

BALANCE STATEMENT

Both of the Woods Center Drive Shredder flail tubes are balanced as rotor assemblies to meet or exceed factory standards before installation. After installation, the shredders are statistically inspected to check balance. These factory efforts allow the shredder to operate smoothly and be free of excessive vibration when delivered to the customer.

■ The operator must be familiar with all safety

rules and safety decals before installing and running the shredder. All personnel must be familiar with and stay out of the hazard area whenever the shredder is running. (See Figure 18, page 22).

Smooth, acceptable vibration levels can be easily estimated in the field. After machine shutdown and coast down has been completed, place a quarter on a clean top panel of the shredder. At full rotor rpm (while maintaining all safety rules regarding safe distances from rotating equipment) observe the quarter. If the quarter stays still and does not bounce around, the operator can estimate that the shredder is free from excessive vibration. If the quarter jumps around during full rotor rpm, the shredder may be operating with excessive vibration where troubleshooting and maintenance are required (refer to the Troubleshooting section).

The Woods Center Drive Flail Shredder has been designed for maximum durability when shredding any type of crop. While operating in the field, many factors can affect and degrade shredder rotor balance and cause increased vibration levels.

● Operating too low to the ground or in frequent con-

tact with the ground can cause the flail knives to

wear unevenly. This can reduce their chopping effect and also increase vibration levels.

● Hitting large rocks or other foreign objects can

damage knives and other rotor parts, causing excessive vibration.

● Over time, certain types of soil and crops can also

lead to uneven knife wear and increased vibration levels.

● Once field operation has been started, it is the

operator’s responsibility to check and maintain shredder rotor balance.

● If knife replacement is required due to wear or

damage, refer to REPLACING FLAILS, page 29.

● Throughout the life of the flail shredder, removing

the flail tubes for replacement or re-balance may be necessary.

● If flail tube replacement is required due to wear or

damage, refer to SERVICING ROTORS (FLAIL TUBES), page 30.

● Any re-balance should be done with all knives

installed.

● Factory balanced repair rotors are available

through your local Woods dealer.

● Consult with your local balance shop experts or

contact Woods Technical Service for re-balance or replacement options.

Continued operation with excessive vibration can cause damage to and shorten component life, void product warranty, and affect personal safety. Checking and maintaining shredder rotor balance is the owner/ operator’s responsibility.

GENERAL INFORMATION

The purpose of this manual is to assist you in operating and maintaining your flail shredder. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation.

MAN0506 (Rev. 9/5/2008)

The illustrations and data used in this manual were current at the time of printing but, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification.

Throughout this manual, references are made to right and left directions. These are determined by standing behind the equipment facing the direction of forward travel.

Introduction 5

Page 6

TRAINING

Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator’s single careless act.

In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment.

It has been said “The best safety device is an informed, careful operator.” We ask you to be that kind of operator.

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

 Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-

6637.) Failure to follow instructions or safety rules can result in serious injury or death.

 If you do not understand any part of this manual and need assistance, see your dealer.

 Know your controls and how to stop engine and attachment quickly in an emergency.

 Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions.

 Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death.

 Make sure that all operating and service personnel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by a doctor familiar with this form of injury or gangrene, serious injury, or death will result. CONTACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. DO NOT DELAY.

 Never allow children or untrained persons to operate equipment.

6 Safety

PREPARATION

 Use a suitable lifting device of sufficient capacity. Use adequate personnel to handle heavy components.

 Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

 Air in hydraulic systems can cause erratic operation and allows loads or equipment components to drop unexpectedly. When connecting equipment or hoses or performing any hydraulic maintenance, purge any air in hydraulic system by operating all hydraulic functions several times. Do this before putting into service or allowing anyone to approach the equipment.

 Make sure all hydraulic hoses, fittings, and valves are in good condition and not leaking before starting power unit or using equipment. Check and route hoses carefully to prevent damage. Hoses must not be twisted, bent sharply, kinked, frayed, pinched, or come into contact with any moving parts. Operate moveable components through full operational range to check clearances. Replace any damaged hoses immediately.

 Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

 When attaching a pull-type unit to the tractor drawbar, always use a high-strength drawbar pin. The drawbar pin must have a device that will lock it into position. Secure safety chain to attachment and tractor.

 Make sure attachment is properly secured, adjusted, and in good operating condition.

 Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO spline groove.

 Before starting power unit, check all equipment driveline guards for damage. Replace any damaged guards. Make sure all guards rotate freely on all drivelines. If guards do not rotate freely on drivelines, repair and replace bearings before putting equipment into service.

 Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

CD Flail Shredder MAN0506 (4/15/2006)

Page 7

 Connect PTO driveline directly to power unit

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

 Inspect rubber flaps and swing rod before each use. Replace if damaged or missing. Flaps must pivot and hang freely so there are no gaps. Do not put equipment into service until repaired.

 Remove accumulated debris from this equipment, power unit, and engine to avoid fire hazard.

 Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

 Always raise unit and install transport locks before transporting. Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

 Always attach safety chain to tractor drawbar when transporting unit.

OPERATION

 Make sure shields and guards are properly installed and in good condition. Replace if damaged.

 A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment.

Do not estimate.

 Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.

TRANSPORTATION

 Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

 A minimum 20% of tractor and equipment weight must be on the tractor front wheels when

 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

 Keep bystanders away from equipment.

 Do not operate or transport equipment while

under the influence of alcohol or drugs.

 Operate only in daylight or good artificial light.

 Keep hands, feet, hair, and clothing away from

equipment while engine is running. Stay clear of all moving parts.

 Always comply with all state and local lighting and marking requirements.

 Never allow riders on power unit or attachment.

 Power unit must be equipped with ROPS or

ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

 Operate tractor PTO at the rpm speed stated in “Specifications” section.

(Safety Rules continued on next page)

CD Flail Shredder MAN0506 (4/15/2006)

Safety 7

Page 8

(Safety Rules continued from previous page)

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

 Look down and to the rear and make sure area is clear before operating in reverse.

 Do not operate or transport on steep slopes.

 Do not stop, start, or change directions sud-

denly on slopes.

 Use extreme care and reduce ground speed on slopes and rough terrain.

 Watch for hidden hazards on the terrain during operation.

 Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

 Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

MAINTENANCE

 Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt.

 Before performing any service or maintenance, lower equipment to ground or block securely, turn off engine, remove key, and disconnect driveline from tractor PTO.

 Use a suitable lifting device of sufficient capacity. Use adequate personnel to handle heavy components.

 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

 Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Follow Operator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

 Make sure attachment is properly secured, adjusted, and in good operating condition.

 Keep all persons away from operator control area while performing adjustments, service, or maintenance.

 Make certain all movement of equipment components has stopped before approaching for service.

 Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from dropping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

 Work not covered in SERVICE & MAINTENANCE must be done by a qualified dealership. Special skills, tools, and safety procedures may be required. Failure to follow these instructions can result in serious injury or death.

 Do not modify or alter or permit anyone else to modify or alter the equipment or any of its components in any way.

 Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous.

8 Safety

 Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

 Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

 Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

CD Flail Shredder MAN0506 (4/15/2006)

Page 9

 Make sure all safety decals are installed.

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!



Replace if damaged. (See Safety Decals section for location.)

 Make sure shields and guards are properly installed and in good condition. Replace if damaged.

 Do not disconnect hydraulic lines until engine is stopped, power unit is properly secured, equipment and all components are lowered to the ground, and system pressure is released by operating all valve control levers.

 Leak down or failure of mechanical or hydraulic system can cause equipment to drop.

STORAGE

 Block equipment securely for storage.

 Keep children and bystanders away from stor-

age area.

 Follow manual instructions for storage.

CD Flail Shredder MAN0506 (4/15/2006)

Safety 9

Page 10

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

1 - YELLOW REFLECTOR PN 20034004

2 - RED REFLECTOR PN 57123

4 - RED-ORANGE FLUORESCENT MATERIAL

PN 20034034

5 - PN 50030977

3 - SERIAL NUMBER PLATE

MODEL NO. SER IAL NO.

Woods Equipment Company

Oregon, Illinois, U.S.A.

CAUTION

1. Read Operator's Manual before starting.

2. Stop tractor engine, place all controls in neutral, lower machine to the ground, set park brake, remove ignition key, and wait for all moving parts to stop before servicing, adjusting, repairing, or unplugging.

3. Keep all guards and access doors closed and secured before operating.

4. Keep hands, feet, hair, and clothing away from moving parts.

5. Do not allow riders.

6. Do not enter rotor area when engine is running.

7. Never exceed 20 MPH when transporting.

8. Use hazard flashers when transporting.

9. Use drawbar pin with retainer and attach safety chain.

10. Wear appropriate hearing protection for prolonged exposure to excessive noise.

11. Review safety information periodically prior to use.

1. Lea el Manual del Operario antes de empezar.

2. Pare el motor del tractor, ponga todos los controles en

3. Mantenga cerrados y asegurados todos los protectores y

4. Mantenga retirados de las piezas móviles, las manos, los

5. No permita que nadie vaya con usted en la máquina.

6. No entre en el área del rotor mientras el motor está en

8. Use luces intermitentes de aviso cuando viaja con la

9. Use el pasador de la barra de tiro con fiador y enganche la

10. Use un protector apropiado para los oidos cuando esté

11. R

PRECAUCION

neutro, baje la máquina hasta el suelo, ponga el freno de estacionamiento, quite la llave del encendido, y espere a que todas las pizas móviles hayan parado antes de dar servicio, hacer ajustes, reparaciones, o de desatascar.

las compuertas antes de poner a funcionar la máquina.

pies, el pelo, y la ropa.

marcha.

Nunca exceda 32 km/h (20 MPH) al transportar.

máquina.

cadena de seguridad.

expuesto a ruido excesivo por un tiempo prolongado.

epase la información de seguridad periódicamente

antes del uso.

50030977-B

10 Safety

MAN0506 (Rev. 9/5/2008)

Page 11

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

DANGER

PELIGRO

ROTATING DRIVELINE HAZARD

To prevent serious injury or death from rotating driveline:

1. Keep all guards in place when operating.

2. Operate only at 1000 RPM.

3. Keep hands, feet, clothing, and hair away from moving parts.

PELIGRO CON EL MOVIMIENTO

ROTATIVO DEL EJE MOTRIZ

Para evitar heridas graves o la muerte a causa de la rotación del eje motriz:

1. Mantenga todos los protectores en su puesto mientras esté funcionando la máquina.

2. Hágala funcionar únicamente a 1000 RPM.

3. Mantenga retirados de las piezas móviles, las manos, los pies, la ropa y el pelo.

50030978-A

6 - PN 50030978

7 - PN 50030982

DANGER

PELIGRO

ROTATING FLAIL HAZARD

To prevent serious injury or death from rotating flails:

1. Stop engine, remove ignition key, and wait for moving parts to stop before servicing.

2. Keep hands and feet away from flails when engine is running.

3. Keep other people away.

PELIGRO CON LAS CUCHILLAS

CORTADORAS ROTATIVAS

Para evitar heridas graves o la muerte causadas por las cuchillas rotativas:

1. Pare el motor, quite la llave del encendido y espere hasta que las piezas móviles hayan parado antes de dar servicio.

2. Mantenga las manos y los pies retirados de las cuchillas estando el motor en marcha.

3. No permita que otra gente se acerque.

50030982-A

8 - PN 50530138

10 - PN 50530314

9 - PN 50530225

MAN0506 (Rev. 9/5/2008)

(Safety Decals continued on next page)

Safety 11

Page 12

SAFETY & INSTRUCTIONAL DECALS

GUARD MISSING.

DO NOT OPERATE.

DANGER

33347E

DANGER

GUARD MISSING.

DO NOT OPERATE.

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

(Safety Decals continued from previous page)

WARNING

ADVERTENCIA

HIGH-PRESSURE FLUID HAZARD

To prevent serious injury or death:

1. Relieve pressure on system before repairing, adjusting, or disconnecting.

2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands.

3. Keep all components in good repair.

PELIGRO DE FLUIDO BAJO

Para evitar heridas graves o la muerte:

1. Alivie la presión del sistema antes de hacer repara ciones, ajustes o desconecciones.

2. Use protección apropiada en las manos y en los ojos, cuando revise para ver si hay fugas. Utilice una tabla o un cartón en vez de las manos.

3. Mantenga todos los componentes en buen estado.

ALTA PRESION

50530315-A

11 - PN 50530707

14 - PN 50530315

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

DO NOT OPERATE WITHOUT -

 All driveline guards, tractor and

equipment shields in place

 Drivelines securely attached at both ends

 Driveline guards that turn freely on

driveline

12 - PN 50530728

15 - PN 18864

DANGER

KEEP AWAY!

16 - PN 33347

18864-C

Use a clean, damp cloth to clean safety decals.

Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off.

Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.

12 Safety

BE CAREFUL!

MAN0506 (Rev. 9/5/2008)

Page 13

OPERATOR SIGN-OFF RECORD

Woods Equipment Company follows the general safety standards specified by the American Society of Agricultural and Biological Engineers (ASABE) and the Occupational Safety and Health Administration (OSHA) for agricultural equipment.

Anyone who will be operating and/or maintaining the flail shredder must read and clearly understand all Safety, Operating, and Service & Maintenance information presented in this manual.

Do not operate or allow anyone else to operate this equipment until this information has been reviewed. Review this information annually, before the season start-up. Make periodic reviews of the Safety and Operation sections standard practice for those using any of your equipment.

Use the following Operator Sign-off Record to verify that each operator has read and understood the information in this manual and has been instructed in the safe operation of the flail shredder.

DATE OPERATOR’S NAME (PRINT) OPERATOR’S SIGNATURE

MAN0506 (Rev. 9/5/2008)

Operator Record 13

Page 14

OPERATION

WARNING

CAUTION

The Woods Flail Shredder is designed to pick up and shred crop and plant residue left in the field. Rotational power to the flails is provided by the tractor PTO.

Be familiar with the flail shredder before starting.

The owner is responsible for training operators in the safe operation of the flail shredder.

 Always comply with all state and local lighting and marking requirements.

6637.) Failure to follow instructions or safety rules can result in serious injury or death.

 Never allow children or untrained persons to operate equipment.



Make sure shields and guards are properly

installed and in good condition. Replace if damaged.

 Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

 Never allow riders on power unit or attachment.

 Before dismounting power unit or performing

any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt.

 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

 Keep bystanders away from equipment.

 Operate tractor PTO at the rpm speed stated in

“Specifications” section.

PRINCIPAL COMPONENTS

The Woods Flail Shredder consists of a large rotating tube with swinging steel flails attached. The flails pick up or strike crop residue or trash and shred it. Rotational power to the drum is provided by the tractor PTO through a gearbox in the center of the machine.

For removing the center strip of crop residue, an optional hydraulically driven blade can be installed under the cover in the center of the machine.

The flail shredder is designed to be used as a pull-type, semi-mounted, or 3-point mounted machine.

BREAK-IN OF THE FLAIL SHREDDER

The following should be observed when operating the unit for the first time:

NOTICE

■ Before operating the unit in the field, run the

PTO clutch. See . Weasler Modular Friction Clutch (24K), page 33.

After operating for 1/2 hour

1. Check all nuts, bolts, and other fasteners. Tighten

to specifications given in the Bolt Torque Chart, page 63.

2. Tighten wheel bolts to specifications given in the Bolt Torque Chart, page 63.

3. Check that the flails are in good condition and swing freely.

4. Check oil level in the gearbox. Add oil if needed.

5. Check that the PTO driveline shield turns freely.

14 Operation

6. Lubricate all grease points.

After operating for 5 to 10 hours

1. Repeat Steps 1 through 5 above.

2. Follow regular service schedule as outlined in

Service & Maintenance, page 24.

MAN0506 (Rev. 9/5/2008)

Page 15

Figure 1. Flail Shredder Principal Components

1. Crossmember

2. Rubber belt shield

3. Skid assembly

4. Rubber belt shield

5. Body weldment

6. Flail tube assembly RH

7. Flail tube assembly LH

8. Woods model decal

9. Gearbox

10. Bearing assembly

PRE-OPERATION CHECK LIST

(OWNER'S RESPONSIBILITY)

NOTICE

■ This Pre-Operation Check List is provided for

the operator. It is important to follow for both personal safety and maintenance of the flail shredder.

___ Check all lubrication points and grease as

instructed in Lubrication Service Record, page

27.

___ Use only a tractor of adequate power and weight

to pull the unit. (See chart below.)

___ Check that the unit is properly attached to the

tractor. On pull-type unit, be sure there is a mechanical retainer through the drawbar pin and the safety chain is installed. On 3-point hitch units, be sure retainers are used on the mounting pins.

___ Check oil level in gearbox. Add oil as required.

___ Check that the PTO driveline turns freely and that

the driveline can telescope easily.

___ Check tire pressure. Inflate to specified level.

___ Check flails. Inspect for damage or breakage.

Make sure they swing freely on their mount. Repair or replace as required.

___ Check condition of cutter blade (if so equipped).

___ Inspect all hydraulic lines, hoses, couplers, and

fittings. Tighten, repair, or replace any leaking or damaged components.

___ Install and secure all guards, doors, and covers.

___ Check PTO clutch operation (see . Weasler Mod-

ular Friction Clutch (24K), page 33).

CHOOSING THE CORRECT TRACTOR

To ensure safe and reliable operation of the flail shredder, use a tractor with the correct specifications. Use the following guidelines to select the correct tractor.

1. Horsepower

Use Table 1 on page 16 for selecting the tractor horsepower class appropriate for your unit’s width.

Increase the horsepower level by 25 percent when operating in hilly, soft, or wet conditions.

2. Tractor Weight

By following recommendations for tractor horsepower, the tractor will have sufficient weight to provide stability for unit during field operation or when transporting.

When using a 3-point mounted shredder, we recommend that each tractor be equipped with a full complement of suitcase weights on the tractor front (see Figure 2 for example). This will provide the required front weight for turning and extra traction if equipped with front wheel assist.

MAN0506 (Rev. 9/5/2008)

Operation 15

Page 16

6. Drawbar (Pull-Type Models Only)

Table 1: Tractor Horsepower (6-8) vs. Unit Width

Width Minimum Horsepower

15′ 90

20′ 120

22′ 132

25′ 150

27′ 162

Top Link Assembly

Upper Top Link Hole

Lower Top Link Pin

Lower 3-Point Pin

1000 RPM 16” or 20”

The tractor drawbar must be set to provide 16" (406 mm) on 1-3/8 - 21 or 20" (508 mm) 1-3/4 - 20 between the end of the PTO shaft and the center of the drawbar pin for all 1000 rpm PTO. See Figure 4. This dimension will provide the required clearance for the CV (Constant Velocity) joint on the front of the driveline.

NOTICE

■ Do not use PTO shaft adapters. They will

change the drawbar dimension and can cause driveline failures.

NOTE: On pull-type models, do not cut driveline.

Figure 2. Tractor Front Weight

3. 3-Point Hitch

The 3-point hitch models require that the tractor be equipped with a Category II or Category III 3-point hitch. If the hitch can be converted from one to the other, use a Category III to provide a wider stance and more stability.

Use the upper top link hole for Category III and the lower hole for Category II as shown in Figure 3.

For easier attachment, use a quick hitch. If not using a quick hitch, use optional hitch extension.

4. Hydraulic Requirements when Using Center Cutter Options

The tractor hydraulic system must be capable of 8 gpm (30 lpm) at 1500 psi (10,335 kPa). Either closed-centered or open-centered systems can be used.

5. Load Sensing Hydraulics (3-Point Models Only)

Many newer tractors are equipped with “load sensing” hydraulics. The operator is responsible for setting the tractor hydraulic system to provide “float” on the 3-point hitch. Refer to the tractor manual for specific instructions.

The “float” feature will allow the unit to follow the ground contours during operation. This applies to 3point mounted machines only.

Figure 3. 3-Point Hitch Attachment

Figure 4. Drawbar Dimension

PTO Driveline Length

(3-Point & 2-Point Models Only)

The unit is equipped with a PTO driveline long enough to fit any tractor and 3-point linkage system.

The operator is responsible for measuring the dimensions of the driveline through its working range. These dimensions will indicate if the driveline requires shorting to operate on the particular tractor/unit attachment system. The operator must check dimensions before using the unit for the first time and each time a different tractor is used with the unit.

Use the following procedure when determining driveline dimension:

16 Operation

MAN0506 (Rev. 9/5/2008)

Page 17

 Keep bystanders away from equipment.

WARNING

CAUTION

1. Clear the area of all bystanders.

2. Attach the 3-point hitch to the unit but not the PTO

driveline.

3. Raise the unit until the tractor PTO and gearbox shafts are the same height.

4. Measure the dimension between the shaft grooves on the tractor and implement ends. If this dimension is less than 34.81 inches, the shaft will require shortening.

5. Move the unit to its highest and lowest working position and measure this dimension again. [The unit’s shaft can telescope (see Figure 6) before it has been shortened.]

6. If required, shorten the shaft to prevent bottoming out during use. NOTE: An extra inch of compression space in the shaft can eliminate bottoming out during use. Measure to make sure.

7. Use an abrasive wheel power saw to cut the male end of the shaft. Cut the same amount from both the splined shaft and the safety shield. See Figure

5. Use a file to remove any burrs from the cut end.

NOTICE

■ Cut only the male end. Never cut the female end.

8. Never cut more than 9 inches from the male end. Cutting 1 inch from the male end shortens both the minimum and maximum lengths by 1 inch.

ATTACHING SHREDDER TO TRACTOR

1. Place unit on a level, dry area free of debris and

other foreign object.

 Keep bystanders away from equipment.

 Connect PTO driveline directly to power unit

PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

2. Clear the area of bystanders, especially children.

3. Provide enough clearance to back the tractor

safely into the unit.

■ Do not allow anyone to stand between tractor

and unit when backing up to the unit.

With Quick Hitch Attachment:

4. Set the height of the 3-point hitch so that quick

hitch claws are lower than the mounting pins.

5. Make sure 3-point hitch is set in the non-sway position. See tractor manual for details.

6. Align the claws under the lower and upper mast mounting pins while backing up.

NOTE: For a Category II hitch, use the bottom upper mast hole. For a Category III hitch, use the top upper mast hole.

7. When the claws are under the pins, slowly raise the 3-point hitch. Make sure each mounting pin seats in its respective claw.

Figure 5. Cutting the Driveline Shaft

MAN0506 (Rev. 9/5/2008)

8. Release the claw retainer locks to secure the mounting pins in the claws.

9. Check the top link frame. It should be free to slide in its mounting slots. This movement allows the unit to follow the ground contour when cresting a hill or going through a depression.

Figure 6. Driveline Dimension

Operation 17

Page 18

Without Quick Hitch Attachment:

1. Back tractor lower 3-point arms between lower

mast plates and align with lower 3-point hole.

2. Place 1-3/4 OD spacer through 3-point arm pivot (both sides).

3. Push tractor’s 3-point arm to the inside and slide a 1-7/16 OD spacer between to take up the empty space. Secure with lower 3-point hitch pin assembly, 1-3/4 OD spacer, and 7/16 x 2 klik pin.

4. Repeat steps 5 and 6 for other side.

5. Lower the tractor’s top link arm and secure in top

hole of upper mast assembly using spacer, hex bolt, and lock nut. (See illustration and parts list, page 48-48.)

Pull-Type Model:

1. Use the ratchet (see Figure 7) on top of the hitch to

set the hitch height.

2. Check and set the drawbar dimension.

3. Back the tractor up to the hitch.

4. Use a hardened drawbar pin that provides for a

mechanical retainer, such as a Klik pin.

5. Attach safety chain from hammer strap around the drawbar or cage to prevent unexpected separation. Provide sufficient slack for turning.

6. Use the ratchet to transfer the unit’s weight to the drawbar.

Figure 8. Drawbar & Safety Chain

Attach PTO Driveline

1. Make sure the driveline telescopes easily and

shields rotate freely.

NOTICE

■ The drawbar may need repositioning to provide

clearance for the driveline.

2. Attach the driveline to the tractor by retracting the

locking collar. Slide the yoke over the shaft and push on the yoke until the lock collar clicks into position. Make sure the yoke is locked into position. See Figure 9.

7. Make sure the drawbar is pinned in its center position.

Figure 7. Attaching to Pull-Type Model

18 Operation

Figure 9. Locking Collar

Attach Hydraulics (Center Cutter Option)

1. Use a clean cloth to clean hose ends and area

around the couplers on the tractor.

2. Insert the hose male ends into the tractor couplers. Make sure hoses lock in place.

3. Route hoses along or over the hitch and secure in position with clips, tape, or plastic ties. Provide enough slack for turning and lifting.

MAN0506 (Rev. 9/5/2008)

Page 19

Raise Stands

WARNING

CAUTION

1. Use hitch ratchets or 3-point hitch to raise the front

of the machine.

2. Unpin front frame stands. Raise and pin in their upper position. See Figure 10.

REMOVING SHREDDER FROM TRACTOR

Reverse the above procedure (Steps 1-17) when removing unit from the tractor.

Figure 10. Parking Stand

 Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

 Never allow riders on power unit or attachment.

 Do not allow bystanders in the area when oper-

ating, attaching, removing, assembling, or servicing equipment.

 Inspect and clear area of stones, branches, or other hard objects that might be thrown, causing injury or damage.



Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions.

 Keep bystanders away from equipment.

 Operate tractor PTO at the rpm speed stated in

“Specifications” section.

FIELD OPERATION

The Woods Flail Shredder is designed with the flexibility to operate well in almost any kind of crop and terrain conditions. However, the operator is responsible for being familiar with all operating and safety procedures and following them. Each operator should review this Field Operation section at the start of the season and as often as required to be familiar with the unit.

Operators should also review the PRE-OPERATION CHECK LIST, page 15, and Attaching Shredder to Tractor, page 17.

6637.) Failure to follow instructions or safety rules can result in serious injury or death.

 Never allow children or untrained persons to operate equipment.



Make sure shields and guards are properly

installed and in good condition. Replace if damaged.

 Always comply with all state and local lighting and marking requirements.

PREPARING FOR OPERATION

1. Pull into the field and position the unit in a level

area.

2. Lower into operating position.

3. 3-Point hitch models: Set the 3-point so the quick

hitch is vertical and the floating upper mast is forward.

Flail Height

Set the unit to give a flail height of at least 3 to 6 inches (75 to 150 mm) above the ground. This will

minimize the amount of stones and dirt picked up by

MAN0506 (Rev. 9/5/2008)

Operation 19

Page 20

the flails under all operating conditions. (See Balance

7109

7111

Floating Top Mast

Statement, page 5.)

NOTE: To avoid unnecessary wear on knives and related parts, never set the unit lower than the recommended setting. (See Balance Statement, page 5.)

Figure 11. 3-Point Hitch Models

4. 3-Point models only: Be sure the floating mast is

free to slide in its mounting frame to allow the machine to follow ground contours. Refer to Figure

13.

SET OPERATING HEIGHT

3-Point Hitch Models

Use the ratchet on the rockshaft mount to set the unit height.

Pull-Type Models

Use the ratchets or cylinders on the hitch and rockshaft mount to set the unit height.

Figure 12. Pull-Type Models (Ratchet)

3-Point & 2-Point Hitch Models

1. Set lower 3-point arms in the free-float position.

2. Set the hitch in the non-swing position.

3. Set the hydraulic system to allow the 3-point to

float. Refer to tractor manual for instructions.

Figure 13. Free-Float Position

FLAIL KNIVES

The shredder is factory equipped with “L” or cup type flails. The two types are interchangeable.

“L” Flails

“L” flails (Figure 15) work best when trash or crop residue is standing.

Cup Flails

Cup flails (Figure 16) can pick up material from the ground and work best in matted trash conditions.

The standard cup flail is 11 inches (279 mm) long and is used for most applications. Optional 7 and 9 inch (177 and 228 mm) flails are available to match the tip position to ground contour.

Attach optional cup flails as follows, making sure that knives at 180° match (see Figure 14) (see Balance Statement, page 5):

1. Leave standard flails located between the rows.

2. Remove others and install shorter flails to follow

ground contour. Be sure to mount the same size flails on opposite sides of the tube. Measure the row spacing and flail position carefully to minimize ground contact. See page 36 and page 37.

20 Operation

MAN0506 (Rev. 9/5/2008)

Page 21

WARNING

Setting Outer Trailing Wheels (Casters & Struts)

Normally, wheels are set to track in the row centers, between the raised seed beds. Tire position will determine flail height, but depth of furrow is also a factor in setting flail height. In some conditions the furrow between the seed beds is deeper on the ends, where irrigation waters enter the field. As furrows change depth, flail height will change.

To compensate for the depth change, move the trailing wheels against the side of the outer seed bed (see Fig-

Figure 14. Optional Flail Contour

ure 17). The wheels will then tend to climb up the side of the seed bed and prevent the flails from hitting the top of the bed.

Set the flail height after the wheels have been moved against the seed bed.

Figure 15. “L” Flails

Figure 16. Cup Flails

Setting Flail Height

1. Be sure wheels are set to follow in the center of furrow row. Set flails 3 to 6 inches (75 to 150 mm) above the ground. (See Balance Statement,

page 5.)

2. Align the unit with the working area on or between rows on flat farming.

3. 3-Point Models: Set the 3-point hitch so the wheels carry only a small portion of the unit’s weight and act more as stabilizing wheels. See tractor manual for setting hitch.

Figure 17. Wheel Position

STARTING THE TRACTOR

1. Run tractor engine at low idle.

2. Slowly engage PTO control to start the shredder.

3. Slowly bring tractor engine to rated PTO speed.

Never exceed rated speed.

STOPPING THE TRACTOR

1. Slowly decrease engine speed to low idle.

2. Disengage center cutter’s hydraulic system (if so

equipped). Never approach unit until the blade has stopped turning.

3. Slowly disengage PTO clutch. The overrunning clutch will allow the shredder to freewheel down.

4. Restart the unit only after the drums quit turning. The PTO will not need to be disengaged to lift the unit on the ends or while turning.

MAN0506 (Rev. 9/5/2008)

Operation 21

Page 22

HAZARD AREA

WARNING

KEEP OUT OF

 Make certain all movement of equipment components has stopped before approaching for service.

Stay away from front, side, and rear of unit while it is running. Flails can pick up stones, sticks, wire, and other debris and throw it out with enough force to severely injure bystanders.

Keep out of shaded area shown in Figure 18.

Shut down unit and wait for moving parts to stop before approaching.

CV joint angle should not exceed 80 degrees in either operating or standstill condition of the driveline. Larger angles will damage the joint.

The angle should never exceed 35 degrees when the driveline is under full load.

NOTICE

■ Disengage PTO when making sharp turns.

Figure 18. Hazard Area

GROUND SPEED

Travel speed can vary between 3 and 8 mph (5 and 13 kmph) depending on the bulk of residue and terrain conditions. The operator is responsible for noting the condition of the work, setting the speed to obtain a quality shredding job, and maintaining control of the unit.

Speed may be increased if shredding quality is good.

Decrease speed if trash is left standing or if some is not picked up.

TURNING

3-Point Mounted Units:

Always raise the unit slightly to lift rear wheels off the ground before turning. This will eliminate side loads on the wheel assembly, unless unit is equipped with caster wheels.

Pull-Type Units:

The front universal is equipped with a CV (Constant Velocity) joint to allow for turning. Although the CV joint allows for sharper turns than a regular driveline, it does have some limitations. Refer to Figure 19.

Figure 19. CV Joint Angles

CLEANING

After Each Use

● Remove large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

● Inspect machine and replace worn or damaged

parts.

● Replace any safety decals that are missing or not

readable.

Periodically or Before Extended Storage

● Clean large debris such as clumps of dirt, grass,

crop residue, etc. from machine.

● Remove the remainder using a low-pressure water

spray.

1. Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface.

2. Be careful when spraying near chipped or scratched paint as water spray can lift paint.

3. If a pressure washer is used, follow the advice of the pressure washer manufacturer.

● Inspect machine and replace worn or damaged

parts.

● Sand down scratches and the edges of areas of

missing paint and coat with Woods spray paint of matching color (purchase from your Woods dealer).

22 Operation

MAN0506 (Rev. 9/5/2008)

Page 23

●

WARNING

3141506

Replace any safety decals that are missing or not readable (supplied free by your Woods dealer). See Safety Decals section for location drawing.

12. Do not allow children to play on or around the

stored unit.

STORAGE

 Block equipment securely for storage.

 Keep children and bystanders away from stor-

age area.

At the end of the season, the shredder should be thoroughly inspected and prepared for storage. Repair or replace any worn or damage components to prevent unnecessary down time at the beginning of the next season.

To ensure a long, trouble-free life, prepare the unit for storage by carrying out the following procedure:

1. Clear the area of bystanders, especially children.

2. Thoroughly wash the unit, using a pressure washer

to remove all dirt, mud, debris, and residue. See Cleaning instructions on this page.

OPTIONAL EQUIPMENT

RUBBER FLAPS

All units are equipped with front shield flaps (Figure 20) along the front of the frame. The shield flaps stop or deflect trash, stones, or other debris picked up by the flails.

Be sure the shield flaps are in good condition for operation. Replace if damaged, torn, or missing.

ADDITIONAL REAR WHEELS

Additional rear wheels (Figure 21) should be installed on machines 18 feet or wider. They provide extra flotation and stability for wide units and are available from your dealer or the factory.

3. Inspect the flails and rotors for damage or entangled material. Remove entangled material. Repair or replace damaged parts.

4. Inspect all hydraulic hoses, lines, couplers, and fittings. Tighten all loose fittings. Replace any hose that is cut, nicked, abraded, or separating from the crimped end of a fitting.

5. Change gearbox oil.

6. Lubricate all grease fittings. Make sure all grease

cavities have been filled with grease to remove any water residue from pressure washing.

7. Touch up all paint nicks and scratches to prevent rust.

8. Move to storage area. Select a dry area free of debris. Store in an area away from human activity.

9. Unhook from tractor (see Removing Shredder from Tractor, page 19).

10. Place safety stands or large blocks under the frame to take the load off the tires. NOTE: Do not deflate tires.

Figure 20. Optional Rear Wheels

BED CONES

3-POINT UNITS ONLY

For some operations you may want to pack hills. Mount bed cones (Figure 21) directly over the row in place of rear wheels.

11. If the unit cannot be placed indoors, cover with a waterproof tarpaulin and tie securely. Store away from human activity.

MAN0506 (Rev. 9/5/2008)

Figure 21. Optional Bed Cones

Operation 23

Page 24

SERVICE & MAINTENANCE

WARNING

CAUTION

grease with extreme pressure (EP) performance. An SAE multi-purpose lithium-based grease is also acceptable.

area while performing adjustments, service, or maintenance.

 Do not handle knives with bare hands. Careless or improper handling may result in serious injury.



Make sure shields and guards are properly

installed and in good condition. Replace if damaged.

 Make certain all movement of equipment components has stopped before approaching for service.

LUBRICANTS

1. Grease

Use an SAE multi-purpose high temperature

2. Gearbox Oil

Use an SAE 85W90 gear oil for all operating conditions. Capacity: 2-1/2 U.S. quarts (110 oz.).

Storing Lubricants

Your unit can operate at top efficiency only if clean lubricants are used. Use clean containers to handle all lubricants. Store them in an area protected from dust, moisture, and other contaminants.

GREASING

NOTE: Use the Lubrication Service Record, page 27 to

keep a record of all scheduled maintenance.

1. Use a hand-held grease gun for all greasing.

2. Wipe grease fitting with a clean cloth before

greasing to avoid injecting dirt and grit.

3. Replace and repair broken fittings immediately.

4. If fittings will not take grease, remove and clean

thoroughly. Also clean lubricant passageway. Replace fitting if necessary.

LUBRICATION SCHEDULE

NOTE: Recommendations are based on normal oper-

ating conditions. Severe or unusual conditions may require more frequent lubrication or oil changes. Refer to Figure 23.

Daily or every 8 hours of operation

PTO Driveline Lubricate daily or every 8 hours of oper-

ation (every 4 hours if U-joints run at angles). See Figure 22 for lubrication points.

24 Service & Maintenance

MAN0506 (Rev. 9/5/2008)

Page 25

Figure 22. PTO Driveline Lubrication Points

A. Daily or 8 hours B. 25 hours C. 40 hours D. Check Daily/Change Annually

(Rev. 1/24/2011)

MAN0506 (Rev. 9/5/2008)

Figure 23. Lubrication Points

Service & Maintenance 25

Page 26

Daily or every 8 hours of operation

7109

7123Z

7114Z

ROTOR DRIVE HUB

GEARBOX OIL DRAIN

7126Z

7104Z

Every 40 hours of operation

1. Lubricate PTO U-joints and over-running clutch.

2. Check gearbox daily or every 8 hours of operation.

See Figure 24 for gearbox oil fill location.

Figure 24. Gearbox Oil Fill Location

Every 25 hours of operation

1. Lubricate PTO driveline telescoping section (one

location, Position B, Figure 23).

2. Lubricate rotor end bearings. See Figure 25.

1. Lubricate rotor drive couplers next to the couplers

on underside of unit and inside of flail tube (use hole in flail tube to access grease fitting, 2 locations).

2. Grease the drive hubs with 10 to 20 pumps. You may use extra grease only on drive hubs.

Annually

1. Change gearbox oil. Refill with SAE 85W90 gear

oil. Capacity: 2-1/2 U.S. quarts (110 oz.). See Figure 27.

3. Lubricate wheel rockshaft bearings (3 to 5 locations). See Figure 26.

Figure 25. Rotor End Bearing

Lubrication Point

Figure 27. Gearbox Oil Drain Location

2. Repack wheel bearings. See Figure 28.

Figure 28. Wheel Bearings

3. Lubricate ratchets as necessary (2 locations each

ratchet). See Figure 29.

Figure 26. Wheel Rockshaft Bearing

Lubrication Points

26 Service & Maintenance

Figure 29. Ratchet Lubrication Points

(Rev. 1/24/2011)

MAN0506 (Rev. 9/5/2008)

Page 27

LUBRICATION SERVICE RECORD

HOURS OF SERVICE

SERVICED BY

10 Hours or daily

L PTO Driveline (8)

L PTO Driveline telescope

section

L U-Joint (1)

L Overrunning clutch (1)

Gearbox oil level

25 Hours

L Rotor end bearings

L Wheel mounting tube

bearings

40 Hours

L Rotor inner bearings (2)

Annually

C Gearbox oil

R Wheel bearings

L Ratchets

✔

NOTE: See page 24 through page 27 for details. Copy this page to continue service record.

GEARBOX OIL LEAKAGE

■ Major oil leakage from the gearbox shaft seal

area is not acceptable and could cause the gearbox to fail due to lack of lubrication and cooling. It is the operator’s responsibility to check the gearbox oil level per the Lubrication Service Table.

Before checking gearbox oil level, shut down the shredder for a couple of hours to allow the oil to drain back into the reservoir for the most accurate reading. Proper oil level should be between the full and add lines on dipstick. When oil is needed, add through the dipstick tube.

NOTICE

■ DO NOT OVERFILL. Lab tests have proven that

overfilling the gearbox can dramatically increase the gearbox operating temperature. In extreme cases this can overheat the oil, reducing its lubricating and cooling properties, and eventually cause shaft seals to deteriorate and fail. Overheated oil has an obvious burnt smell; drain it and refill with new oil. Overfilling gearbox oil can void the warranty.

The gearbox should not require frequent servicing of oil. It is not designed to consume or lose large amounts of oil. If oil needs to be added frequently, troubleshooting the cause is required (see section below).

MAN0506 (Rev. 9/5/2008)

Service & Maintenance 27

Page 28

Gearbox leakage & Troubleshooting

Some gearbox oil leakage may be acceptable if:

1. Oil covers less than a 3-inch diameter circle around the shaft seal area (see Figure 30).

Woods dealer. Consult with Woods Technical Service for further details, rebuild recommendations, or warranty questions.

CHANGING GEARBOX OIL

2. Oil covers less than a 4-inch diameter circle around the dipstick tube (see Figure 30).

If oil leakage covers an area larger than that described in 1 and 2, do the following:

1. Properly check oil level. If low, properly service.

2. Clean oily area of gearbox. Use a degreaser to

remove all oil from outside surface of gearbox.

3. Closely monitor gearbox for 10 hours of operation. Check and service oil every 30 minutes or as needed to ensure operation does not occur with oil below the add mark.

4. If after 10 hours of operation, oil covers less than the area described in 1 & 2 above, seepage is considered to be acceptable.

5. If after 10 hours of operation, oil covers more than the area described in 1 & 2 above, this seepage is considered to be unacceptable leakage.

6. Gearboxes with unacceptable leakage should be rebuilt, replacing old seals and worn parts with new seals and parts. Gearbox rebuild and seal replacement parts are available through your local

Although gearbox oil never wears out, dust, dirt, and moisture can enter through the breather during operation. These contaminants must be removed once a year to ensure a long life for working components. In very dusty or dirty conditions, change the oil twice a year.

1. Clear area of bystanders, especially children.

2. Shut off tractor, place all controls in neutral, set

parking brake, remove key, and wait for all moving parts to stop.

3. Raise the unit to provide access to underside. Place safety stands or large blocks under frame.

4. Disconnect PTO driveline and hydraulic lines.

5. Place a pan under drain plug. Remove drain plug

and dipstick plug (see Figure 31).

6. Allow gearbox to drain for 10 minutes.

NOTE: To remove the most contaminants, drain oil

when gearbox is hot.

Figure 30. Acceptable Oil Leakage

28 Service & Maintenance

MAN0506 (Rev. 9/5/2008)

Page 29

Figure 31. Drain Plug (Underside of Unit)

DRAIN PLUG

WARNING

7. Re-install and tighten drain plug.

8. Dispose of used oil in an approved container.

9. Add SAE 85W90 gear oil through the dipstick

cover. Use the dipstick to check the oil level (Figure

32) and add oil accordingly.

10. Re-install and tighten fill plug.

11. Reconnect PTO driveline and hydraulic lines.

2. Shut off tractor, place all controls in neutral, set

parking brake, remove key, and wait for all moving parts to stop.

3. Use a jack with sufficient capacity to lift the frame.

4. To determine wheel spacing, measure from the

center line of the unit. Mark positions on the frame.

5. Lift frame until wheels have cleared the ground.

6. Place safety stands or large blocks under the

frame.

7. Loosen mounting bolts on one wheel assembly.

8. Slide assembly along the frame tube to new

position (see Figure 33).

9. Tighten mounting bolts to specified torque level.

12. Remove blocks or safety stands.

Figure 32. Dipstick Location

RATCHET HEIGHT ADJUSTMENT

Mechanical ratchets provide height setting for the unit. To set ratchets, follow this procedure:

1. Clear the area of bystanders, especially children.

2. Turn the turnbuckle to achieve the desired ratchet

length (see Figure 32). Repeat Step 2 with other ratchets.

WHEEL SPACING

The rear wheels can be adjusted for alignment with crop rows.

1. Clear the area of bystanders, especially children.

Figure 33. Positioning Wheel Assembly

10. Remove safety stands or blocks.

11. Lower and remove jack.

12. Repeat with other wheel assembly.

REPLACING FLAIL KNIVES

 Do not handle knives with bare hands. Careless or improper handling may result in serious injury.

■ Read Balance Statement, page 5, before replac-

ing any knives.

The flail knives in pairs swing on a hardened bushing, designed to reduce wear, and are sandwiched between two steel spacers. The hardened bushing is bolted to the clip with a 1/2" NC carriage bolt and a flange lock nut.

1. Clear the area of any bystanders.

2. Shut off tractor, place all controls in neutral, set

parking brake, remove key, and wait for all moving parts to stop.

MAN0506 (Rev. 9/5/2008)

Service & Maintenance 29

Page 30

3. Disconnect driveline and hydraulic lines from the

WARNING

tractor.

4. Place safety stands or large blocks under the frame.

5. Loosen and remove the worn flail and its opposite on the other side of the rotor. Discard worn flails and their mounting hardware.

6. Replace with new flails and mounting hardware (see Figure 34).

Figure 35. Front Rubber Shield Flaps

4. Replace damaged flap with new flap and secure

with correct hardware.

NOTE: Use only genuine Woods parts when replacing flaps.

SERVICING ROTORS (FLAIL TUBES)

Figure 34. Flail Replacement

NOTICE

■ To maintain rotor balance, always replace oppo-

site (180°) pairs of flails and mounting hardware.

7. Tighten flail mounting flange lock nut.

8. Replace additional worn flails following step 5 and

step 6.

9. Remove safety stands or blocks from under frame.

10. Lower unit and remove jack.

11. Attach driveline and hydraulic line to tractor.

12. Refer to Balance Statement, page 5, for balance

issues.

REPLACING RUBBER SHIELD FLAPS

Rubber shield flaps on the front of the unit deflect or prevent stones or debris from being ejected when operating unit. Replace if damaged or missing to provide a safe work environment. To replace, follow this procedure:

1. Clear the area of bystanders, especially children.

2. Lower the unit to the ground, place all controls in

neutral, shut off engine, set park brake, remove key, and wait for all moving parts to stop before dismounting.

NOTE: For 3-point hitch units, unhook to gain access to center flaps.

3. Remove 3/8" nut, washer and carriage bolt from each worn flap. (Replace any worn or damaged hardware. See page 48 for hardware sizes.)

 Do not handle knives with bare hands. Careless or improper handling may result in serious injury.

■ Any excessive vibration caused by worn or

missing knives or damaged drive components can cause damage to the shredder and personal injury. Excessive vibration can also be transmitted through the hitch mounts and PTO to the tractor resulting in tractor damage.

■ Once field operation has been started, it is the

responsibility of the owner/operator to monitor and maintain acceptable rotor balance. Refer to Balance Statement, page 5, for details.

NOTICE

■ Read Balance Statement, page 5, before replac-

ing any knives.

Refer to Replacing Flails, page 29, for knife or knife component replacement.

The Woods Center Drive Flail Shredder has been designed for durability when shredding any type of crop. Some operating conditions will shorten the life of the shredder or components. These include operating too low to the ground or in frequent contact with the ground, and contact with large rocks or other foreign objects. Over time, some types of soils and crops can cause wear or damage to rotor components and affect rotor balance, leading to increased vibration. Continued operation with excessive vibration can damage the shredder, requiring rotor service, removal, or replacement.

Factory balanced spare replacement rotors are available through your local Woods dealer. Contact Woods

30 Service & Maintenance

MAN0506 (Rev. 9/5/2008)

Page 31

Technical Service for re-balance options or further

CAUTION

P E E R

F S 2 1 1

details.

Follow the procedure below if rotor removal or replacement is required.

 Use a suitable lifting device of sufficient capacity. Use adequate personnel to handle heavy components.

1. Clear the area of any bystanders.

2. Shut off tractor, place all controls in neutral, set

parking brake, remove key, and wait for all moving parts to stop.

LOCKING COLLAR SET SCREW

LOCKING COLLAR

SHAFT

FOR REMOVAL: TAP WITH A HAMMER AND PUNCH AFTER LOOSENING SET SCREW.

FOR INSTALLATION: REVERSE PROCEDURE

MAN0506003

Figure 36. Locking Collar

Replacing Components

3. Remove PTO driveline from the shredder.

4. Fully disconnect the shredder from the tractor.

5. Remove wheel arms (casters or struts).

6. Use a hoist, crane, or frame of sufficient capacity to

raise the front of the unit and allow the back of the unit to rest on a solid surface (blocks).

7. Leave lifting device attached while working on rotors to prevent tipping.

Removing Components

Refer to Replacing Flails, page 29, for knife or knife component replacement.

Refer to Servicing Rotors, page 30, before proceeding with these steps.

1. Follow steps in the previous section to prepare and position shredder. Support each end of the rotor (flail tube) to be removed with a crane or hoist.

2. Remove bearing locking collar (see Figure 36).

3. Remove the six bolts holding the bearing plate to

the body assembly.

4. Slide rotor out to disengage from the center drive coupling.

5. Thoroughly clean and inspect gearbox drive couplings for wear and replace if any wear is detected. Also inspect the rubber O-ring for wear or tears and replace if any wear or tears are detected.

6. Remove crossmember from the underside of the shredder, providing access for the removal of the gearbox.

7. Remove gearbox, if damaged. This will require removal of the second rotor (repeat steps 1-5 above).

1. Place new stud bolts into gearbox using Loctite No. 271 or equivalent.

2. Remount gearbox. The gearbox oil dipstick should protrude out the top panel of the shredder for checking and servicing. Reinstall the nuts and lock washers securing the top of the gearbox to the shredder gearbox mount plate and torque to specifications in Bolt Torque Chart, page 63.

3. Remount the crossmember securing the bottom of the gearbox and torque to specifications in Bolt Torque Chart, page 63.

4. Install drive couplings and reapply new grease around entire O-ring and gear teeth surfaces.

5. Install rotors (flail tubes) in the opposite fashion as removal. Position rotors with each end supported by a crane or hoist so that it is aligned with the gear coupling and gearbox output shaft center lines. The bearing (stub shaft) end of the rotor will protrude out of the hole in the end sheet.

6. With gentle care not to damage gear coupler teeth or O-ring, provide pressure to align gear teeth and slide the rotor back into its original position.

NOTE: When re-installing rotors, the gear coupling grease fitting will need to be temporarily removed to allow for air to purge from the coupler assembly during installation. After successful installation, reinstall grease fitting and re-service.

7. Reinstall bearing plate assembly and bolts, and apply appropriate torque.

8. Reinstall bearing locking collar and tighten (see Figure 36).

NOTICE

■ If removing rotor drive coupling, use Loctite No.

271 or equivalent and special high collar lock washers to keep bolts from loosening.

MAN0506 (Rev. 9/5/2008)

Service & Maintenance 31

Page 32

REPLACING STUB SHAFT

1. Remove rotor (see Servicing Rotors (Flail Tubes),

page 30).

2. Remove three 1/2 x 2-1/2 hex bolts in taper lock hub and re-install bolts in three threaded holes (see Figure 38).

3. Tighten bolts evenly to release taper lock hub from stub shaft. NOTE: You may have to give a sharp blow directly to each bolt head to help the hub disengage.

Figure 37. Rotor Direction of Rotation

Figure 38. Stub Shaft Assembly

SERVICING WEASLER MODULAR FRICTION CLUTCH

Tools Required

• 3/4" Socket wrench

• 8" Minimum C-clamps (2)

• 1/4" Hex Allen wrench

• Regular screwdriver or punch

• Duct tape or locking pliers with 3" throat minimum

•Hammer

• 1/2" sq. to 1" sq. bar x 9"

•Scale or Vernier

Breaking In the Clutch (Run In)

NOTE: All new clutches must be broken in (Run in) and

any clutch that has not been used for approximately 60 days.

1. Shut off tractor and disengage PTO.

2. Disconnect driveline from the tractor PTO shaft.

3. Loosen the bolts on the outside diameter of the

clutch until all bolts are just loose, then tighten all bolts 1/2 turn.

4. Unscrew stub shaft from the rotor tube.

5. Install new stub shaft, reversing Steps 1-3.

4. Attach the driveline to the tractor PTO. Stand clear

of the unit.

5. Start tractor. Engage PTO clutch and run for a few seconds or until clutch visibly smokes.

6. Disengage PTO. Shut off tractor. Disconnect driveline from the tractor.

7. Tighten all bolts on the outside diameter of the clutch until the compression plate is tight against the housing.

8. Grease the fitting on the yoke, using a multipurpose high-temperature EP grease or an equivalent lithium grease.

9. For an integral overrunning clutch, make sure clutch turns freely in one direction.

Removing the Driveline

1. Shut off tractor and disengage PTO.

2. Disconnect driveline from PTO shaft.

3. Remove the bolt (21K) or clamp (24K) that

attaches the clutch to the shredder’s input shaft.

32 Service & Maintenance

MAN0506 (Rev. 9/5/2008)

Page 33

NOTE: The shaft is heavy. Grasp the clutch firmly with both hands and slide off the input shaft.

Rebuilding Friction Pack

Disassembly

Inspection

1. Inspect the steel parts for wear and replace if

necessary.

2. Inspect the yoke/hub for looseness. If there is more than .03 end play, replace.

1. Position clutch and universal joint assembly on a bench so that end is accessible.

2. Remove the long bolts on the outside of the housing that hold the friction pack together.

3. Remove the plate(s) and all internal components. Leave the yoke/hub intact.

4. Discard friction discs.

5. If rebuilding the overrunning clutch, refer to

Rebuilding Overrunning Clutch, page 33, beginning with Step 2.

Inspection

1. Inspect the steel and iron parts for wear, warping,

or cracks, and replace if necessary.

2. Inspect the yoke/hub for looseness. If there is more than.03 end play, replace.

3. Clean any rust or dust from the plate surfaces with a wire brush or steel wool.

Assembly

3. Using screwdriver, scrape any hardened grease

from the overrunning key pockets.

Assembly

1. Using a multi-purpose high-temperature EP grease

or equivalent lithium grease, inject one grease gun pump into each key pocket. Evenly wipe two more pumps over the overrunning surface.

2. Press a new leaf spring into each pocket. The ends should touch the bottom of the pockets.

1. Place one new friction disc, then separator plate, then second friction disc into housing.

2. Add the pressure plate so that the flat surface rests on the friction disc. NOTE: The tangs on the plate must fall into the reliefs in the housing.

3. Add the disc spring so that its inside diameter contacts the fins of the pressure plate.

4. Assemble the compression plate and all the long bolts. Make sure all nuts rest in their pockets.

5. Tighten all long bolts to 30 lbs-ft.

Rebuilding Overrunning Clutch

Disassembly

1. Remove the four bolts that secure the friction pack.

Remove the friction pack.

2. Using screwdriver and pliers, remove the retaining ring that holds the overrunning clutch together.

3. Slide the collar and washer off the clutch hub, noting the orientation of the collar for reinsertion.

4. Remove and discard the keys and leaf springs.

Figure 39. Weasler Modular Friction Clutch (24K)

3. Add new keys. With one hand, hold the two keys in

the pockets.

4. Slide the collar onto the hub, orienting collar correctly.

5. Add washer.

6. Install retaining ring.

7. Make sure clutch spins freely and only in correct

direction.

8. Reassemble friction pack.

MOUNTING CLUTCH TO SHREDDER

1. Mount and bolt the clutch hub onto the shredder

input shaft. Make sure shaft and clutch grooves line up.

2. Re-install any shielding that was moved or removed.

3. Run the clutch before using. Refer to Breaking In the Clutch (Run In), page 32.

MAN0506 (Rev. 9/5/2008)

Service & Maintenance 33

Page 34

NOTES

34 Service & Maintenance

MAN0506 (Rev. 9/5/2008)

Page 35

TROUBLESHOOTING

The Woods Flail Shredder uses swinging flails to pick up and shred crop residue left in the field. It is a simple and reliable system that requires minimal maintenance.

The following table lists problems, causes, and solutions that you may encounter. If you encounter a problem that is difficult to solve even after reading through this table, please call your local Woods dealer. When calling, please have this manual and your unit’s serial number ready.

PROBLEM CAUSE SOLUTION

Shredder doesn’t track Poor wheel spacing Set wheels in center of crop rows.

3-Point not set Set 3-point hitch in non-sway

position.

Shredder not level Level shredder (see Set Operating

Height, page 20).

Irrigation furrows not even Set wheels against seed bed (see

Setting Outer Trailing Wheels (Casters & Struts), page 21).

Shredder doesn’t follow ground contour

Shredder vibrates Driveline doesn’t telescope. Remove, disassemble, and clean

Debris is being thrown out from under shredder

3-Point not set Set 3 point in float position.

See tractor manual to set Load Sensing hydraulic system.

Shredder too high Set shredder closer to ground.

Irrigation furrows not even Set wheels against seed bed.

telescoping joint.

Rotor out of balance Replace damaged or broken flails

and flails 180 degrees opposite.

Check for missing balance weights or rebalance.

Shredder set too low Raise shredder.

Knives excessively worn Replace knives.

Rubber shields missing Replace flaps immediately.

Crop residue is being left Traveling too fast Slow travel speed.

Shredder too high Lower shredder.

Improper flails Change flails.

MAN0506 (Rev. 9/5/2008)

Crop residue strip left in shredder center

Troubleshooting 35

Add center cutter or divider.

Page 36

WORKSHEET FOR CONTOUR FLAIL PATTERNS

36 Contour Flail Patterns

MAN0506 (Rev. 9/5/2008)

Page 37

WORKSHEET FOR CONTOUR FLAIL PATTERNS

24’

MAN0506 (Rev. 9/5/2008)

Contour Flail Patterns 37

Page 38

ASSEMBLY

WARNING

CAUTION

DEALER SET-UP INSTRUCTIONS

 Do not allow bystanders in the area when operating, attaching, removing, assembling, or servicing equipment.

 Do not handle knives with bare hands. Careless or improper handling may result in serious injury.

 Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual.

After the unit has been leveled for a couple of hours, check oil level and service through the dipstick/filler tube as required.

Figure 40. Dipstick Shipping Plug Removal

WHEEL ASSEMBLY

1. Raise the rear of the unit.

2. Place safety stands or large blocks under frame.

 Use a suitable lifting device of sufficient capacity. Use adequate personnel to handle heavy components.

1. Open the crate and cartons containing the

attaching components and mounting hardware.

2. Use the packing list to check that all parts have been shipped.

For Some Models Shipped on End

Units that stand on their aft ends during shipping have a dipstick shipping plug installed in the gearbox dipstick tube to prevent leakage during shipping.

NOTICE

■

For units shipped on aft end, the dipstick shipping plug must be removed before shredder operation. Replace plug with dipstick in filler tube after shredder has been removed from truck and leveled.

3. Measure the wheel spacing from the center of the

unit. Mark the frame (rockshaft).

4. Install the wheel assembly to the rockshaft (Figure

41). If equipped with caster wheels, verify that

there is enough clearance for casters to rotate without hitting each other. Failure to do so will

result in tire damage.

5. Tighten mounting bolts to their specified torque.

Figure 41. Wheel Assembly Installed

3-POINT UNITS

6. Attach floating upper mast (1) to shredder using

two hardened bushings, 1 x 5" hex bolts, lock nuts, and four 3/4 x 3" spacers. See parts list for hardware, page 48-48. (Keep hardware loose.)

38 Assembly

MAN0506 (Rev. 9/5/2008)

Page 39

7. Attach front top link spacer, bolts, and lock nuts to

7082Z

front of upper mast assembly.

NOTE:

For Quick Hitch Cat II, use spacer in front lower hole of upper mast assembly. For Quick Hitch Cat III, use spacer in front upper hole of upper mast assembly. Without Quick Hitch, use spacer through top link pivot in front upper hole of upper mast assembly.

8. Assemble lower 3-point hitch pin assembly, spacers, and klik pin to lower mast (both sides).

NOTE: For Quick Hitch Cat II & III, place 1-3/4 OD spacer on the inside and 1-7/16 OD spacer on the outside.

3. Install front parking stands (Figure 44), using L-pin and hair pin cotter.

Figure 44. Front Stands Installed

PULL-TYPE HITCH INSTALLATION

(Pull-type units only)

1. Mount hitch to 3-point lower mounts, using pins

and Klik pins.

2. Install ratchet. Be sure to install retaining pins.

3. Attach clevis or pin to hitch tongue (See page 48

for parts breakdown.)

Figure 42. Floating Upper Mast Installed

ALL UNITS

1. Install PTO driveline by sliding the yoke with the

slip clutch over the input shaft (Figure 43).

2. Tighten interlocking clamp bolts to their specified torque.

4. Attach tow chain to hitch.

Figure 45. Pull-Type Hitch Installed

Figure 43. Gearbox Input Shaft

MAN0506 (Rev. 9/5/2008)

Assembly 39

Page 40

MANUAL STORAGE TUBE INSTALLATION

1. Rubber flap

2. Flap bracket, right

3. Flap bracket, left

5. flap rod

6. Swing flap bar, mast plate

7. Swing flap bar

8. 3/8 NC x 1 Carriage bolt

9. 3/8 NC Flange lock nut

10. 3/16 x 1-1/2 Cotter pin

The manual storage tube may be supplied in either of the following styles.

NOTE: Use equal number of belting and bars on each side of shredder.

3. Tighten all hardware.

For One-Piece Style Manual Tube:

Mount the manual tube to the inside of the shredder side sheet, using three 3/8 x 1-1/4" hex bolts, washers, and 3/8" nuts. Mounting holes are located above the bearing plate (see Figure 46).

Figure 46. One-Piece Style Manual Tube Installed

For Clamp-Style Manual Tube:

1. Mount the tube clamp to the inside of the shredder

side sheet using two 1/4" self-tapping screws (Figure 47). Mounting holes are located above the bearing plate.

2. Place the tube in the clamp with the cap facing forward.

RUBBER FLAP INSTALLATION

1. Remove all components from shipping carton.

Make sure that all required hardware is included.

2. Attach flap brackets to the front of the shredder using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange lock nuts.

NOTE: Use flap brackets to space flap brackets out evenly across front of shredder.

3. Attach flap bars to flat brackets using 3/8 NC x 11/2 carriage bolts and 3/8 flange lock nuts.

4. Assemble rod and rubber flaps through flap brackets and secure using 3/16 x 1-1/2 cotter pins.

5. Tighten all hardware.

6. For detailed installation instructions, see the parts

diagram and instruction sheet the comes with the swing flap kit designed for each shredder.

NOTE: Keep the Operator’s Manual with the shredder at all times.

Figure 47. Clamp-Style Manual Tube Assembly

OPTIONAL EQUIPMENT

RUBBER BELTING INSTALLATION

1. Remove all components from shipping carton.

Make sure that all required hardware is included.

2. Attach rubber belting and bars to front of shredder using 3/8 NC x 1-1/2 carriage bolts and 3/8 flange lock nuts.

40 Assembly

Figure 48. Rubber Flat Installation (15’ Shown)

SAFETY LIGHT KIT INSTALLATION

1. Remove all components from shipping carton.

Make sure that all required hardware is included.

2. Attach dual safety lights (Figure 49) to their bases using 1/4 NC x 1" hex bolts, washers and nuts

MAN0506 (Rev. 9/5/2008)

Page 41

provided. Make sure that light lenses are in the

5. Dual lamp, 4-pin LH

6. Dual lamp, 4-pin RH

8. Clamp, adhesive-backed

9. 1/4 NC x 1" Hex bolt

10. 1/4 NC Hex nut

11. 1/4" Lock washer

12. 1/4" Flat washer

20. Wiring harness

21. Dual light bracket

DP3

1. Center deflector

2. 1/2 NC x 1-1/4 carriage bolt

3. 1/2 NC Flange lock nut

correct position in relation to direction of equipment travel: amber lenses on the outside, red lenses on the inside facing rear of shredder.

3. Install light bracket on end of shredder using 1/2 NC x 1-1/2" hex bolts, washers and nuts (four each) in slots 3 and 4 on top of end sheet.

4. Plug ends of wiring harness into corresponding plugs of the light units (Note: left side of wishbone harness is labeled “Left”).

5. Run wiring harness along top of shredder and secure with enclosed adhesive-backed clamps (5) approximately every two feet.

6. Connect 7-pin connector of wiring harness to tractor and test all light functions before actual use.

Figure 51. Safety Light Installed - Front View

Install Center Deflector

Slide deflector (1) between shredder center channel with the point forward.

Secure into position using four 1/2 NC x 1-1/4 carriage bolts (2) and flange lock nuts (3).

Figure 49. Safety Light Kit Diagram (Non-End Tow)

Figure 50. Safety Light Installed - Rear View

MAN0506 (Rev. 9/5/2008)

Figure 52. Center Deflector Installed

Assembly 41

Page 42

CENTER CUT KIT INSTALLATION

WARNING

Block Shredded

To minimize the potential hazards of working underneath the cutter, follow these procedures.

1. Jackstands with a load rating of 2000 lbs or more are the only approved blocking device for this cutter. Install a minimum of four jackstands under the shredder before working underneath unit.

2. Install adapter (23) and hose (11) to the OUT or RETURN side of the motor.

3. Place motor (4) inside motor housing (2) and secure using six 9/16 NC x 1-1/2 cap screws (7) lock nuts (6). Make sure OUT or RETRUN side of motor is on the open side of the motor housing. Torque hardware to 171 lbs-ft.

4. Slide blade hub (1) over motor shaft, install 1/4" key and secure using one 5/16 NF x 1-1/2 cap screw (20), flat washers (33) and lock washer (34) in the bottom of the shaft. Torque to 19 lbs-ft.

5. Clamp hub to shaft using two 3/8 NC x 1-3/4 cap screws (18) and lock nuts (22). Torque to 35 lbs-ft.

6. Secure blade (3) to blade hub using two 3/8 NC x 1-1/4 cap screws (19) and flange lock nuts (22). Torque to 35 lbs-ft.

Do not position jackstands under wheels, axles, or wheel supports. Components can rotate and cause shredder to fall.

2. Consider the overall stability of the blocked unit. Just placing jackstands underneath will not ensure your safety.

The working surface must be level and solid to support the weight on the jackstands. Make sure jackstands are stable, both top and bottom. Make sure shredder is approximately level.

3. With full shredder weight lowered onto jackstands, test blocking stability before working underneath.

4. If shredder is attached to tractor when blocking, set the brakes, remove key, and block shredder before working underneath.

5. Securely block rear tractor wheels, in front and behind. Tighten tractor lower 3-point arm anti-sway mechanism to prevent side-to-side movement.

Assemble Motor and Blade

1. Install elbow (8), adapter (9), elbow (10) and hose

(11) to the IN or PRESSURE side of the hydraulic motor.

Figure 53. Motor Assembly

42 Assembly

MAN0506 (Rev. 9/5/2008)

Page 43

Install Motor Housing

DP1

Check Val ve

Center Plate

RETURN

PRESSURE

DP2

OUT

1. Slide motor assembly between shredder center channel and secure to the left side using two 1/2 NC x 1-1/4 carriage bolts (29) and flange lock nuts (30).

2. Install 1/2 NC x 1 cap screw (31) and flat washer (32) to the right rear hole of the motor housing and secure with flange lock nuts (30).

3. Install 1/2 NC x 1-1/4 carriage bolt (29) and flange lock nut (30) into the right front hole.

4. Raise motor housing to the bottom of the mounting slots and torque hardware to 85 lbs-ft.

4. Place hose assembly around center plate of shredder and drape quick couplers over the front of the shredder. See Figure 55 and Figure 56.

5. Make sure hose with check valve is on the right side of the center plate.

Figure 55. Hose Assembly

6. Route hose (11) from the IN side of the motor

between shredder and rockshaft and attach it to tee (12) on the left side of the center plate.

Assembly Hoses

Figure 54. Motor Assembly Installed

1. Attach male quick coupler (17) and adapter (16) to

the end of hose (15). Attach tee (12) to the opposite end of hose.

2. Attach male quick coupler (17) and adapter (16) to the end of second hose (15). Attach check valve (14), nipple (13) and tee (12) to the opposite end of hose.

NOTE: Make sure flow indicator arrow on the side of the check valve (14) is pointing in the correct direction. See Figure 55

3. Install check valve (14) and two nipples (13) between the two tees (12).

NOTE: Make sure flow indicator arrow on the side of the check valve (14) is pointing in the correct direction.

7. Route hose (11) from the OUT side of the motor between shredder and rockshaft and attach it to tee (12) on the right side of the center plate.

Figure 56. Hose Routing

MAN0506 (Rev. 9/5/2008)

Assembly 43

Page 44

Install Hose Clamps



Connect Hoses to Tractor

1. Place hose clamps (36) around hoses (11) and

center hoses between center plate.

2. Mark clamp holes in desired location on shedder body and drill two 11/32" holes.

3. Secure hose clamps to shredder using 5/16 NF x 1-1/4 cap screws (20), flat washers (33), lock washers (34) and hex nuts (35). See Figure 57.

NOTICE

■ Oil flow to hydraulic motor must not exceed 28

gpm.

1. Connect PRESSURE hose to a tractor rear remote

quick coupler that has a lever (handle) that can be placed in the detent or locked position.

2. RETURN hose must be connected directly to the tractor reservoir or to a specifically designated motor return or ‘zero’ back pressure port.

Install Decals

Apply safety decals (24 & 25) to a clean surface on the back of the shredder where they can be seen with out obstructions. Install decals (25) on either side of the hose assembly. See Figure 57.

Remove Deflector Kit

1022652 deflector kit must be removed from the shredder before using cutter kit. Deflector kit pushes material away from the cutter kit and preventing material from being cut.

Figure 57. Hose Clamp Installation

44 Assembly

MAN0506 (Rev. 9/5/2008)

Page 45

DEALER CHECK LISTS



PRE-DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

Inspect the equipment thoroughly after assembly to make sure that it is set up properly before delivering it to the customer.

The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made.

___ Check that all safety decals are installed and in

good condition. Replace if damaged.

___ Properly attach implement to tractor and make all

necessary adjustments.

___ Check all bolts to be sure they are properly

torqued.

___ Check wheel bolts for proper torque.

___ Check that all cotter pins and safety pins are

properly installed. Replace if damaged.

___ Check and grease all lubrication points as identi-

fied in Lubrication Schedule, page 24.

DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

___ Show customer how to make adjustments.

___ Instruct customer how to lubricate and explain

the importance of lubrication.

___ Point out the safety decals. Explain their meaning

and the need to keep them in place and in good condition. Emphasize the increased safety hazards when instructions are not followed.

___ Present Operator's Manual and request that cus-

tomer and all operators read it before operating equipment. Point out the manual safety rules, explain their meanings and emphasize the increased safety hazards that exist when safety rules are not followed.

___ Explain to customer the potential crushing haz-

ards of going underneath raised equipment. Instruct customer that service work does not require going underneath unit and never to do so.

___ Show customer the safe, proper procedures to be

used when mounting, dismounting, and storing equipment.

___ For mounted units, add wheel weights, ballast in

front tires, and/or front tractor weight to enhance front end stability. A minimum 20% of tractor and equipment gross weight must be on front tractor wheels. When adding weight to attain 20% of tractor and equipment weight on front tractor wheels, you must not exceed the ROPS weight certification. Weigh the tractor and equipment. Do not estimate!

___ Make customer aware of optional equipment

available so that customer can make proper choices as required.

MAN0506 (Rev. 9/5/2008)

Dealer Check Lists 45

Page 46

NOTES

46 Dealer Check Lists

MAN0506 (Rev. 9/5/2008)

Page 47

PARTS INDEX

FLAIL SHREDDER

Center Drive

FRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-48

FLAIL TUBE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

WHEEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

BED CONE ASSEMBLY (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . .52

WEASLER® PTO SHAFT WITH TORQMASTER CLUTCH

24K PULL-TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 - 53

24K 2-POINT & 3-POINT . . . . . . . . . . . . . . . . . . . . . . . . . .54

DUAL SAFETY LIGHT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

WEASLER 24K TORQMASTER CLUTCH . . . . . . . . . . . . . . . . . . . . . .55

WEASLER 30K AUTOMATIC CLUTCH (OPTIONAL). . . . . . . . . . . . . .55

WEASLER PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)

30K 3-POINT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

30K PULL-TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

CENTER DRIVE GEARBOX ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . .58

RUBBER BELTING (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

CENTER CUTTER KIT (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . 60 - 61

CENTER DEFLECTOR (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . .61

RUBBER FLAPS (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

(Rev. 10/13/2010)

MAN0506 (Rev. 9/7/2011)

Parts

Page 48

CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY

48 Parts

MAN0506 (Rev. 9/5/2008)

Page 49

CENTER DRIVE FLAIL SHREDDER FRAME ASSEMBLY PARTS LIST

REF PART QTY DESCRIPTION

1 NSS 1 S15CD Body weldment 1 NSS 1 S20CD Body weldment 1 NSS 1 S22CD Body weldment 1 NSS 1 S25CD Body weldment 1 NSS 1 S27CD Body weldment 2 ---------- - Flail tube asy, right & left

(see page 50) 3 1016168 1 15’ Rockshaft asy 3 1013097 1 20’ Rockshaft asy 3 1016167 1 22’ Rockshaft asy 3 1013057 1 25’ Rockshaft asy 3 1013122 1 27’ Rockshaft asy 5 90507112 1 Tow chain (pull-type only) 6 1012170 2 Bearing, 2-3/16 flange 7 1010120 2 Bearing plate 8 56383 2 Pin weldment 9 50520211 2 Parking stand, square

10 50530279 2 Parking stand pin 14 1013049 1 Gearbox 800 Series (see page 58) 16 1016104 1 3-Point PTO shaft, 1-3/8" yoke with

clutch (see page 52)

16 1016105 1 3-Point PTO shaft, 1-3/4" yoke with

clutch (see page 52)

16 1016106 1 3-Point PTO shaft, 1-3/8" yoke with

clutch long (see page 52)

16 1016107 1 3-Point PTO shaft, 1-3/4" yoke with

clutch long (see page 52)

16 1016108 1 Pull-type PTO shaft, 1-3/8" yoke

with clutch (see page 52)

16 1016109 1 Pull-type PTO shaft, 1-3/4" yoke

with clutch (see page 52)

17 1012175 1 Gearbox stand 20 90025004 * 2 1/8 Hair pin cotter 21 90025012 * 2 7/16 x 2 Klik pin 22 20020705 1 Ratchet jack with pipe 24 20020553 2 Lower 3-pt hitch pin assembly

24a 90029204 * 1 5/16 x 1-5/8 Roll pin

25 90006143 24 1/2 NC Nut, Spiralock flanged 27 1019786 1 Dipstick tube/Jam nut/Dipstick 29 1019755 - Complete safety decal set 30 12735 * 24 1/2 NC x 1-3/4 HT Carriage bolt 31 90023084 * 2 3/8 x 3-1/2 Cotter pin 32 230 * 8 5/8 NC Nut ZP 33 90001786 * 8 5/8 NC x 2 Carriage bolt 34 90011015 * 8 5/8 Lock washer

REF PART QTY DESCRIPTION

36 20973 * AR 3/8 NC x 1-1/4 Carriage bolt GR5 37 565 * AR 3/8 Flat washer 38 90006500 * AR 3/8 NC Top lock nut

39 50530831 1 Hitch, Cat 3 complete (items 51-54)

41 90002734 * 4 5/8 NC x 1-3/4 Hex bolt, black 42 90006019 2 1" NC Nut 43 1013067 2 Skid weldment 44 1012202 AR Rubber belt shield 45 1016188 AR Rubber belt shield, 15’ & 27’ 45 1016195 AR Rubber belt shield, 20’ 45 1019763 AR Rubber belt shield, 22’ 47 10033957 1 Manual storage tube, clamp style

-or47 1003828 1 Manual storage tube, 1-piece style 48 90011021 2 1" Lock washer 49 50530219 1 Pin, rear hitch 50 50520412 1 Pull-type hitch weldment 51 50530834 1 Top plate 52 50530832 1 Cushion 53 50530833 1 V-Plate 54 90001411 2 3/4 NC x 3 Hex bolt GR5 55 90001537 2 1 NC x 6-1/2 Hex bolt GR5 58 90023081 * 2 3/8 x 2 Cotter pin 59 50520433 1 Clevis hitch kit 60 20030151 1 1" ID Mast spacer bushing 63 50030338 2 Drive hub, splined inner 64 90109126 2 O-Ring, flail coupler 65 90039030 4 Snap ring, 1-3/4 66 50530313 4 Stud bolt, 5/8 NC x 2-3/4 GR5 67 1016187 4 Spacer mast .75 x 3.00 68 1016186 2 Hardened bushing 69 90001531 5 Bolt, 1 x 5 HHCS GR5 70 90006514 5 Nut, 1 NC Top lock 71 20030960 2 Spacer, 1-3/4 OD 72 20030961 2 Spacer, 1-7/16 OD 73 20030959 2 Spacer. 1-3/4 OD 75 1013114 2 Upper mast plate 76 20020553 2 Lower 3-pt hitch pin asy 77 90017110 2 1/4 x 1/2 Hex wash self-tap screw 78 10033958 1 Clamp

AR As Required

NSS Not Sold Separately

* Standard hardware; obtain locally

MAN0506 (Rev. 9/7/2011)

Parts

Page 50

FLAIL TUBE ASSEMBLY

REF

LEFT

PART #

1 1016199LK 1016198LK 1 15’ Flail tube w/knives 1 1016199HD 1016198HD 1 15’ HD Cotton tube

1 1016199CP 1016198CP 1 15’ Cup knife tube

1 1013109LK 1013108LK 1 20’ Flail tube w/knives 1 1013109HD 1013108HD 1 20’ HD Cotton tube

1 1013109CP 1013108CP 1 20’ Cup knife tube

1 1016179LK 1016178LK 1 22’ Flail tube w/knives 1 1016179HD 1016178HD 1 22’ HD Cotton tube

1 1016179CP 1016178CP 1 22’ Cup knife tube

1 1012169LK 1012168LK 1 25’ Flail tube w/knives 1 1012169HD 1012168HD 1 25’ HD Cotton tube

1 1012169CP 1012168CP 1 25’ Cup knife tube

1 1013119LK 1013118LK 1 27’ Flail tube w/knives 1 1013119HD 1013118HD 1 27’ HD Cotton tube

1 1013119CP 1013118CP 1 27’ Cup knife tube

RIGHT

PART #

QTY DESCRIPTION

w/knives

REF PART QTY DESCRIPTION

2 1012163 2 Stub shaft, 2-3/16" 3 50531067 AR L-Knife, long 8-1/2", (6 mm) 3 1019788 AR L-Knife, HD cotton

(Durafaced) (8 mm) 4 50531048 AR Weld-on clip 5 50030779 12 3/8 High collar lock washer 6 1010056 AR L- Knife, cut off 6 1019789 AR L- Knife, cut off 7 50030345 2 Drive hub sleeve, outer 8 1013092 12 3/8 NC x 2-1/2 SHCS 9 90002526 6 1/2 NC x 2-3/4 Tap bolt, full thread

10 90515001 * 2 1/8 NPT Straight grease fitting

11 1012164 2 2-7/16 Hub, E-style 12 90001357 * AR 5/8 NC x 3-1/2 Hex bolt GR5 13 50530405 AR Hardened wear bushing 14 50530974 AR Steel cup flail 11" (Standard) 14 50530973 AR Steel cup flail 9" 14 50530972 AR Steel cup flail short 15 90011013 * AR 1/2 Lock washer 16 11900 * AR 1/2 NC Flange lock nut 17 90006508 AR 5/8 NC Top lock nut 18 90011015 * AR 5/8 Lock washer 19 1010061 AR Spacer, steel (for 6 mm L-knife) 19 1012184 AR Spacer, steel (for 8 mm L-knife) 20 1010062 AR Bushing, L-knife

21 90001758 * AR 1/2 NC x 3-1/4 Carriage bolt

50 Parts

SHCS Socket Head Cap Screw

NS Not Shown

AR As Required

* Standard hardware, obtain locally

MAN0506 (Rev. 9/5/2008)

Page 51

WHEEL ASSEMBLY

REF PART NO QTY DESCRIPTION

1 90509009 1 Dust cap

2 90109002 1 Seal

3 90101023 1 Inner bearing cone

4 90101022 1 Inner cup

5 90509011 5 1/2 NF Wheel nut

6 90509003 1 Hub, 5-bolt

7 90101016 1 Outer bearing cup

8 90101015 1 Outer bearing cone

9 90509067 1 7/8 Washer

10 90023043 * 1 3/16 x 1-1/2 Cotter pin

11 90006060 1 7/8 NF Slotted nut

12 90509070 1 Tire, 9.5L x 15

13 90509078 1 Wheel rim (15" x 6 - 5 bolt)

14 90509117 5 1/2 NF x 1-7/8 Stud bolt

15 2377 6 3/4 NC x 6 Hex bolt GR5

(Qty: 8 for 1010013 & 1010014)

REF PART NO QTY DESCRIPTION

16 50520111 1 Strut weldment

16 50520112 1 Strut assembly with hubs

17 1010013 1 Caster arm assembly (8 holes)

18 50520197 1 Caster weldment

18 50520198 1 Caster and hub assembly

19 1010014 1 Back plate (8 holes)

20 20031233 1 Oilite washer

21 20031219 1 Plate, retainer

22 20031766 2 Caster pivot bearing

23 90515024 * 1 1/4 - 28 UNF Straight grease fit-

ting

24 90001221 * 1 1/2 NC x 1 Hex bolt GR5

26 90006015 8 3/4 NC Hex nut

27 90011017 8 3/4 Lock washer

* Standard hardware, obtain

locally

MAN0506 (Rev. 9/7/2011)

Parts

Page 52

BED CONE ASSEMBLY (OPTIONAL) 50510065

REF PART NO QTY DESCRIPTION

1 20031440 1 U-Bolt, 3/4 NC x 4 x 5.5 long

2 2377 6 3/4 NC x 6 Hex bolt GR5

3 50520162 1 Strut weldment

4 50520163 1 Yoke weldment

5 50530349 1 Scraper

6 50520164 1 Roller weldment

7 90001696 * 7 3/8 NC x 1-1/4 Carriage bolt GR5

8 90101002 2 1-1/4 Insert bearing

9 NSS 4 2-Hole flange

A 50520179 1 Packer asy (Items 4-9)

NSS Not sold separately

* Standard hardware, obtain locally

TYPE A - WEASLER

REF PART NO QTY DESCRIPTION

1 19851 1 Slide lock repair kit 1.38 ID -or-

2 90317733 1 Slide lock yoke asy 1.38 ID -or-

3 58759 2 Cat 6 CV U-joint repair kit

4 19840 1 CV Bell shield

5 58760 1 CV Body with fitting

6 90318183 1 Yoke & shaft 26.8

7 19846 2 Shield bearing repair kit

8 18864 1 Safety sign

9 55648 1 Centralizer repair kit (not shown)

19837 1 Slide lock repair kit 1.75 ID

90318121 1 Slide lock yoke asy 1.75 ID

24K PULL-TYPE PTO SHAFT WITH TORQMASTER CLUTCH

52 Parts

REF PART NO QTY DESCRIPTION

10 1010819 1 Outer guard & bearing

11 1010820 1 Inner guard & bearing

12 33347 1 Decal, Danger, Guard missing

13 90317909 1 Yoke, tube & slip sleeve

14 58765 1 U-Joint cross & bearing kit

15 1010805 1 Clutch asy, 55 clamp 24K

A 1016108 1 PTO CV 1.38-21 CD P-type 24KE

A 1016109 1 PTO CV 1.75-20 CD P-type 24KE

B 1016127 1 Tractor half asy with guard 1.38

B 1016125 1 Tractor half asy with guard 1.75

(Rev. 8/23/2011)

MAN0506 (Rev. 9/5/2008)

Page 53

TYPE B - WEASLER® 24K PULL-TYPE PTO SHAFT WITH TORQMASTER CLUTCH

REF PART NO QTY DESCRIPTION

A 1016108 1 PTO complete 1-3/8 21 spline -or-

A 1016109 1 PTO complete 1-3/4 20 spline

1 19851 1 Slide lock repair kit 1.38 ID -or-

19837 1 Slide lock repair kit 1.75 ID

2 1033104 1 Slide lock yoke asy 1.38 ID -or-

1033105 1 Slide lock yoke asy 1.75 ID

3 1033107 2 Cat 6 CV U-joint repair kit

4 19840 1 CV Bell shield

5 1033106 1 CV Body with fitting

6 1033109 1 Yoke & shaft

7 19846 2 Shield bearing repair kit

8 18864 1 Safety sign

9 55648 1 Centralizer repair kit (not shown)

REF PART NO QTY DESCRIPTION

10 1010819 1 Outer guard & bearing

11 1010820 1 Inner guard & bearing

12 33347 1 Decal, Danger, Guard missing

13 90317909 1 Yoke, tube & slip sleeve

14 58765 1 U-Joint cross & bearing kit

15 1010805 1 Clutch asy, 55 clamp 24K

A 1016108 1 PTO CV 1.38-21 CD P-type 24KE

A 1016109 1 PTO CV 1.75-20 CD P-type 24KE

B 1016127 1 Tractor half asy with guard 1.38

B 1016125 1 Tractor half asy with guard 1.75

(Rev. 10/13/2010)

MAN0506 (Rev. 9/7/2011)

Parts

Page 54

WEASLER® 24K 2-POINT & 3-POINT PTO SHAFT WITH TORQMASTER CLUTCH

CD6523

REF PART NO QTY DESCRIPTION

5 90401149 1 Dual lamp, 4-pin LH

6 90401150 1 Dual lamp, 4-pin RH

8 90507121 12 Clamp, adhesive-backed

9 90001009 * 10 1/4 NC x 1 Hex bolt GR5

10 90006001 * 10 1/4 NC Hex nut

11 90011009 * 10 1/4 Lock washer

12 90011031 * 10 1/4 Flat washer

20 90401152 1 Wiring harness, wishbone

26’

21 50530986 2 Bracket, dual safety light

* Standard hardware, obtain

locally

REF PART QTY DESCRIPTION

1 19851 1 Slide lock repair kit 1.38 ID -or1 19837 1 Slide lock repair kit 1.75 ID 2 90317208 1 Slide yoke assembly 1.38 ID -or- 2 90317418 1 Slide yoke assembly 1.75 ID 3 1016113 2 U-Joint cross & bearing kit 4 90318183 1 Yoke & shaft 26.8 center-end -or- 4 90318074 1 Yoke & shaft, 32.9 center-end 5 19846 1 Shield bearing repair kit 6 18864 1 Safety sign 7 1010803 1 Outer guard & bearing (1016117,

1016111) -or-

7 1010813 1 Outer guard & bearing (1016122,

1016124) 8 1010804 1 Inner guard & bearing 9 33347 1 Safety sign, Danger, Guard missing

DUAL SAFETY LIGHT KIT (OPTIONAL)

REF PART QTY DESCRIPTION

10 90317724 1 Yoke, tube & slip sleeve 11 1010805 1 Friction overrunning clutch asy. 55

clamp (24K) A 1016104 1 PTO Shaft complete 1-3/8 -21 CD Std A 1016105 1 PTO Shaft complete 1-3/4 -20 CD Std B 1016106 1 PTO Shaft complete 1-3/8 -21 CD

long B 1016107 1 PTO Shaft complete 1-3/4 -20 CD

long C 1016117 1 Tractor half asy w/guard 1-3/4 Std C 1016111 1 Tractor half asy w/guard 1-3/8 Std D 1016122 1 Tractor half asy w/guard 1-3/8 long D 1016124 1 Tractor half asy w/guard 1-3/4 long E 1016112 1 Implement half asy w/guard 24K

54 Parts

(Rev. 8/23/2011)

MAN0506 (Rev. 9/5/2008)

Page 55

WEASLER® 24K TORQMASTER CLUTCH ASSEMBLY

REF PART NO QTY DESCRIPTION

9 90318170 1 Leaf spring

10 90318171 1 Overrunning key

11 90318175 2 Friction disk

12 90318174 1 Separator plate

13 90003055 4 M10 x 1.50 x 25 Serrated hex

head cap screw

14 90003053 6 M8 x 1.25 x 60 Hex bolt, CL 10.9

15 90011236 A/R Washer, 8 mm x 1.6 thick

16 90006548 6 Nut, M8 x 1.25 Hex ZP

17 1010833 1 Hub clamp asy 1.75

A 1010832 1 Friction pack, overrunning (10

mm bolts, 24K)

B 1010805 1 Complete clutch asy, 55 clamp

(10 mm bolts, 24K)

NSS = Not Serviced Separately

REF PART NO QTY DESCRIPTION

1 1010831 1 Yoke, Clamp style with overrun-

ning clutch & hub asy (10 mm bolts) (includes Items 2-10)

1A 1019629 1 Overrunning clutch repair kit

(includes items 2, 6, 7, 9, & 10)

2 90318165 1 Wave spring

3 90318154 1 Set screw, .312-18 x .25 long

4 90317541 31 Ball, 1/4" dia.

5 1019630 1 OR Inner hub assembly

6 90318167 1 Washer

7 90318168 1 Retaining ring

8 90318169 1 Overrunning hub

REF PART NO QTY DESCRIPTION

A 1019811 - Automatic clutch asy complete

1 1019813 1 Yoke & hub, 30K auto

2 1019814 1 Clutch pack, 30K auto

3 1010833 1 Hub clamp assembly 1-3/4

4 1025874 6 HHCS, M12-1.75P x 20 mm

CL10.9 flanged head

WEASLER® AUTOMATIC CLUTCH (OPTIONAL)

MAN0506 (Rev. 9/7/2011)

Parts

Page 56

WEASLER® 30K 3-POINT PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)

REF PART QTY DESCRIPTION

A 1019810 - PTO Shaft complete 1-3/4 20-spline

30K 3-point with automatic clutch 1 19837 1 Slide lock repair kit 1.75 ID 2 90317418 1 1-3/4 20-Spline yoke 3 58765 2 U-Joint cross & bearing kit 55E 4 1022637 1 Yoke & shaft, (1.69 - 20 spline) 5 1009065 2 Drive shield bearing kit

WEASLER® 30K 3-POINT PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)

REF PART QTY DESCRIPTION

6 90317455 1 Safety sign 7 1022638 1 Outer guard & bearing 8 1022639 1 Inner guard & bearing

9 33347 1 Danger decal, guard missing 10 1022640 1 Yoke, tube & slip sleeve 11 1019811 1 Automatic clutch assembly 30K (see

page 55 for breakdown)

REF PART QTY DESCRIPTION

A 1026555 - PTO Shaft complete 1-3/4 20-spline

30K 3-point with automatic clutch 1 19837 1 Slide lock repair kit 1.75 ID 2 90317418 1 1-3/4 20-Spline yoke 3 58765 2 U-Joint cross & bearing kit 55E 4 90317613 1 Yoke & shaft, 1.69 20-spline, 30.6 long

-OR- -OR4 90318183 1 Yoke & shaft, 1.69 20-spline, 26.8 long 5 1009065 2 Drive shield bearing kit

56 Parts

REF PART QTY DESCRIPTION

6 90317455 1 Safety sign 7 1010803 1 Outer guard & bearing 8 1010804 1 Inner guard & bearing

9 33347 1 Danger decal, guard missing 10 90317724 1 Yoke, tube & slip sleeve 11 1019811 1 Automatic clutch assembly 30K (see

page 55 for breakdown)

(Rev. 11/8/2011)

MAN0506 (Rev. 9/5/2008)

Page 57

TYPE A - WEASLER® 30K PULL-TYPE PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)

REF PART QTY DESCRIPTION

A 1019820 - PTO Shaft complete 1-3/4 20-spline

30K pull-type with automatic clutch 1 19837 1 Slide lock repair kit 1.75 ID 2 90318121 1 Slide lock yoke assembly 3 58759 2 CV U-Joint repair kit 55E 4 58760 1 CV Body with fitting 5 1022641 1 Yoke & shaft (1.69 - 20 spline) 6 1009065 2 Drive shield bearing kit

REF PART QTY DESCRIPTION

7 18864 1 Safety sign 8 1022642 1 Outer guard & bearing

9 1022643 1 Inner guard & bearing 10 33347 1 Danger decal, guard missing 11 1022644 1 Yoke, tube & slip sleeve 12 58765 2 U-Joint cross & bearing kit 55E 13 1019811 1 Automatic clutch assembly 30K (see

page 55 for breakdown)

TYPE B - WEASLER® 30K PULL-TYPE PTO SHAFT WITH AUTOMATIC CLUTCH (OPTIONAL)

REF PART QTY DESCRIPTION

A 1019820 - PTO Shaft complete 1-3/4 20-spline

30K pull-type with automatic clutch 1 19837 1 Slide lock repair kit 1.75 ID 2 1033105 1 Slide lock yoke assembly 3 1033107 2 CV U-Joint repair kit 55E 4 1033106 1 CV Body with fitting 5 1033109 1 Yoke & shaft (1.69 - 20 spline) 6 1009065 2 Drive shield bearing kit

(Rev 10/13/2010)

MAN0506 (Rev. 9/7/2011)

REF PART QTY DESCRIPTION

7 18864 1 Safety sign 8 1022642 1 Outer guard & bearing

page 55 for breakdown)

Parts

Page 58

CENTER DRIVE GEARBOX

REF PART QTY DESCRIPTION

A 1013049 1 Complete gearbox, Series 800 1 1019782 1 Casting, Threaded holes 2 1019783 1 Casting, Non-threaded holes 3 1019784 1 Pinion shaft/gear asy 27T with bearing

cones & bearing cups 4 90315546 1 Cross shaft/gear asy 20T 5 90101150 1 Bearing cone 6 90101152 2 Bearing cup 7 1019785 4 Bolt, 3/8-16 x 2.75 SHCS 8 1019787 3 Guard, seal 9 90039030 1 Snap ring 1.750

10 90109125 3 Seal TC-1.750-2.437-.312 11 90503078 2 Plug, 1/2-14 NPT SCHD W/3M 12 90003033 8 Bolt, 3/8-16 x 2.25 SHCS 13 90501159 1 Bushing, 1/2 NPT to 1/8 NPT 14 90101328 1 Bearing cone 15 NSS - Bearing cone (included in item 3) 16 NSS - Bearing cone (included in item 3)

NSS Not Serviced Separately

58 Parts

MAN0506 (Rev. 9/5/2008)

Page 59

RUBBER BELTING

REF PART QTY DESCRIPTION

1 1012202 4 Rubber belting (15 ft) 1 1012202 6 Rubber belting (20 ft & 22 ft) 1 1012202 8 Rubber belting (25 ft & 27 ft) 2 1022647 4 Belt bar (15ft) 2 1022647 6 Belt bar (20 ft & 22 ft) 2 1022647 8 Belt bar (25 ft & 27 ft) 3 1022649 2 Belt bar (15 ft & 27 ft) 3 1022648 2 Belt bar (20 ft) 3 1022650 2 Belt bar (22 ft) 4 1016188 2 Rubber belting (15 ft & 27 ft) 4 1016195 2 Rubber belting (20 ft) 4 1019763 2 Rubber belting (22 ft)

REF PART QTY DESCRIPTION

5 64824 * 34 3/8 NC x 1-1/2 Carriage bolt (15 ft) 5 64824 * 46 3/8 NC x 1-1/2 Carriage bolt (20 ft) 5 64824 * 50 3/8 NC x 1-1/2 Carriage bolt (22 ft) 5 64824 * 62 3/8 NC x 1-1/2 Carriage bolt (25 ft) 5 64824 * 34 3/8 NC x 1-1/2 Carriage bolt (27 ft) 6 14350 * 34 3/8 NC flange lock nut (15 ft) 6 14350 * 46 3/8 NC flange lock nut (20 ft) 6 14350 * 50 3/8 NC flange lock nut (22 ft) 6 14350 * 26 3/8 NC flange lock nut (25 ft) 6 14350 * 62 3/8 NC flange lock nut (27 ft)

* Standard hardware, obtain locally

MAN0506 (Rev. 9/7/2011)

Parts

Page 60

CENTER CUTTER KIT (OPTIONAL)

24 - 50530315

25 - 50530263

HIGH-PRESSURE FLUID HAZARD

To prevent serious injury or death:

1. Relieve pressure on system before repairing, adjusting, or disconnecting.

2. Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands.

3. Keep all components in good repair.

Para evitar heridas graves o la muerte:

1. Alivie la presión del sistema antes de hacer repara ciones, ajustes o desconecciones.

2. Use protección apropiada en las manos y en los ojos, cuando revise para ver si hay fugas. Utilice una tabla o un cartón en vez de las manos.

3. Mantenga todos los componentes en buen estado.

60 Parts

WARNING

ADVERTENCIA

PELIGRO DE FLUIDO BAJO

ALTA PRESION

50530315-A

MAN0506 (Rev. 9/5/2008)

Page 61

CENTER CUTTER KIT PARTS LIST

REF PART QTY DESCRIPTION

1 1016151 1 Center deflector 2 301109 * 4 1/2 NC x 1-1/4 Carriage bolt GR5 3 11900 * 4 1/2 NC Flange lock nut

* Standard hardware, obtain locally

REF PART QTY DESCRIPTION

1 1024671 1 Blade hub

2 1016161 1 Motor housing

3 1024674 1 Blade, .31 x 2.50 x 13.31 dbl edge

4 1017719 1 Hydraulic motor

6 58125 * 6 9/16 NC Lock nut

7 58452 * 6 9/16 NC x 1-1/2 HHCS GR8

8 90503099 1 Elbow, 1-1/16 ORBM x 3/4NPTF

9 27309 1 Adapter, 3/4 NPTF x 3/4 NPTM

10 1023026 1 Elbow, 3/4 NPTM x 3/4 NPTF 90°

11 90506021 2 Hose, 40" x 3/4 NPTM x 3/4 NPTM

12 90503098 2 Tee, 3/4 NPTF

13 90501239 3 Nipple, 3/4 NPTM

14 90503097 2 Check valve, 3/4 NPT

15 90506016 2 Hose, 114" x 3/4 NPTM x 3/4 NPTM

16 90501303 2 Adapter, 1/2 NPTM x 3/4 NPTF

REF PART QTY DESCRIPTION

17 90519003 2 Quick coupler, male

18 90001115 * 2 3/8 NC x 1-3/4 HHCS GR5

19 12169 * 2 3/8 NC x 1-1/4 HHCS GR5 20 66 * 3 5/16 NF x 1-1/2 HHCS GR5 22 14350 * 4 3/8 NC Flange lock nut 23 1023035 1 Adapter, 1-5/16 ORBM x 3/4 NPTF 24 50530315 1 Decal, Hydraulic pressure 25 50530263 2 Decal, Rotating blades 29 301109 * 3 1/2 NC x 1-1/4 Carriage bolt 30 11900 * 4 1/2 NC Flange lock nut 31 25475 * 1 1/2 NC x 1 HHCS GR5 32 854 * 1 1/2 Flat washer 33 4378 * 3 5/16 Flat washer 34 2472 * 3 5/16 Lock washer 35 5283 * 2 5/16 NF Hex nut 36 1004695 2 Clamp, 1.94 dia Pipe

HHCS Hex Head Cap Screw

* Standard hardware, obtain locally

CENTER DEFLECTOR (OPTIONAL)

MAN0506 (Rev. 9/7/2011)

Parts

Page 62

RUBBER FLAP

REF PART QTY DESCRIPTION

1 50531089 14 Rubber flap (12" - 15 ft) 1 50531089 18 Rubber flap (12" - 20 ft) 1 50531089 20 Rubber flap (12" - 22 ft) 1 50531089 24 Rubber flap (12" - 25 ft) 1 50531089 26 Rubber flap (12" - 27 ft) 2 1022659 3 Flap bracket, right (15 ft) 2 1022659 4 Flap bracket, right (20 ft) 2 1022659 5 Flap bracket, right (22 ft & 25 ft) 2 1022659 6 Flap bracket, right (27 ft) 3 1022660 3 Flap bracket, left (15 ft) 3 1022660 4 Flap bracket, left (20 ft) 3 1022660 5 Flap bracket, left (22 ft & 25 ft) 3 1022660 6 Flap bracket, left (27 ft) 4 1022661 2 Rubber flap (2", 15 ft & 27 ft) 4 1022662 2 Rubber flap (8.5", 20 ft & 22 ft) 5 1022654 2 Flap rod (15 ft) 5 1022655 2 Flap rod (20 ft)

REF PART QTY DESCRIPTION

5 1022656 2 Flap rod (22 ft) 5 1022657 2 Flap rod (25 ft) 5 1022658 2 Flap rod (27 ft) 6 1026528 2 Swing flap bar, mast plate (32" all) 7 1026529 2 Swing flap bar (32", 20 ft, 25 ft, 27 ft) 8 15028 * 20 3/8 NC x 1 Carriage bolt (15 ft) 8 15028 * 28 3/8 NC x 1 Carriage bolt (20 ft) 8 15028 * 32 3/8 NC x 1 Carriage bolt (22 ft) 8 15028 * 36 3/8 NC x 1 Carriage bolt (25 ft) 8 15028 * 40 3/8 NC x 1 Carriage bolt (27 ft) 9 14350 * 20 3/8 NC Flange lock nut (15 ft) 9 14350 * 28 3/8 NC Flange lock nut (20 ft) 9 14350 * 32 3/8 NC Flange lock nut (22 ft) 9 14350 * 36 3/8 NC Flange lock nut (25 ft) 9 14350 * 40 3/8 NC Flange lock nut (27 ft)

10 90023043 * 4 3/16 x 1-1/2 cotter pin

* Standard hardware, obtain locally

62 Parts

MAN0506 (Rev. 9/5/2008)

Page 63

BOLT TORQUE CHART

SAE SERIES TORQUE CHART

SAE Bolt Head

Identification

SAE Grade 2

(No Dashes)

SAE Grade 5

(3 Radial Dashes)

SAE Grade 8

(6 Radial Dashes)

METRIC SERIES TORQUE CHART

Metric Bolt Head

Identification

8.8

Metric

Grade 10.9

10.9

Metric

Grade 8.8

Typical Washer Installations

Lock Washer

Flat Washer

8/9/00

Bolt

Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.

Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.

Diameter

(Inches)

1/4" 7/16" 6 8 10 13 14 18

5/16"1/2"121719262737

3/8"9/16"233135474967

7/16"5/8"3648557578106

1/2" 3/4" 55 75 85 115 120 163

9/16" 13/16" 78 106 121 164 171 232

5/8" 15/16" 110 149 170 230 240 325

3/4" 1-1/8" 192 261 297 403 420 569

7/8" 1-5/16" 306 416 474 642 669 907

1" 1-1/2" 467 634 722 979 1020 1383

Diameter &

Thread Pitch

(Millimeters)

6 x 1.0 10 mm 8 6 11 8 8 6 11 8 6 x 1.0

8 x 1.25 13 mm 20 15 27 20 21 16 29 22 8 x 1.0

10 x 1.5 16 mm 39 29 54 40 41 30 57 42 10 x 1.25

12 x 1.75 18 mm 68 50 94 70 75 55 103 76 12 x 1.25

14 x 2.0 21 mm 109 80 151 111 118 87 163 120 14 x 1.5

16 x 2.0 24 mm 169 125 234 173 181 133 250 184 16 x 1.5

18 x 2.5 27 mm 234 172 323 239 263 194 363 268 18 x 1.5

20 x 2.5 30 mm 330 244 457 337 367 270 507 374 20 x 1.5

22 x 2.5 34 mm 451 332 623 460 495 365 684 505 22 x 1.5

24 x 3.0 36 mm 571 421 790 583 623 459 861 635 24 x 2.0

30 x 3.0 46 mm 1175 867 1626 1199 1258 928 1740 1283 30 x 2.0

Wrench

Size

Wrench

Size

Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9

N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft

SAE 2 SAE 5 SAE 8

lbs-ft N-m lbs-ft N-m lbs-ft N-m

Coarse Thread Fine Thread

Marking on Head Marking on Head

MARKING ON HEAD

Diameter &

Thread Pitch

(Millimeters)

Bolt Torque & Size Charts (Rev. 3/28/2007)

Appendix 63

Page 64

BOLT SIZE CHART

NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.

SAE Bolt Thread Sizes

5/16 3/8 1/2 5/8 3/4 7/8

IN 1 7

MM 25 50 75 100 125 150 175

Metric Bolt Thread Sizes

8MM 18MM14MM12MM10MM 16MM

ABBREVIATIONS

AG .............................................................. Agriculture

ASABE .................... American Society of Agricultural &

Biological Engineers (formerly ASAE)

ASAE....... American Society of Agricultural Engineers

ATF................................Automatic Transmission Fluid

BSPP.............................British Standard Pipe Parallel

BSPTM................ British Standard Pipe Tapered Male

CV ....................................................Constant Velocity

CCW.............................................. Counter-Clockwise

CW .............................................................. Clockwise

F .......................................................................Female

FT.............................................................. Full Thread

GA .....................................................................Gauge

GR (5, etc.)........................................... Grade (5, etc.)

HHCS ........................................ Hex Head Cap Screw

HT ...........................................................Heat-Treated

JIC.................Joint Industry Council 37° Degree Flare

LH................................................................. Left Hand

LT ...........................................................................Left

m ........................................................................ Meter

mm ............................................................... Millimeter

M ..........................................................................Male

MPa ........................................................ Mega Pascal

N ......................................................................Newton

NC...................................................... National Coarse

NF ...........................................................National Fine

NPSM .................... National Pipe Straight Mechanical

NPT...........................................National Pipe Tapered

NPT SWF......... National Pipe Tapered Swivel Female

ORBM ...........................................O-Ring Boss - Male

P ..........................................................................Pitch

PBY.......................................................Power-Beyond

psi ......................................... Pounds per Square Inch

PTO......................................................Power Take Off

QD ...................................................Quick Disconnect

RH.............................................................. Right Hand

ROPS........................... Roll-Over Protective Structure

RPM........................................Revolutions Per Minute

RT ........................................................................Right

SAE..........................Society of Automotive Engineers

UNC ..................................................... Unified Coarse

UNF ..........................................................Unified Fine

UNS ..................................................... Unified Special

64 Appendix

Bolt Torque & Size Charts (Rev. 3/28/2007)

Page 65

INDEX

ASSEMBLY

Dealer Set-Up Instructions Optional Equipment

Center Cut Kit Installation 42 Rubber Belting Installation 40 Rubber Flap Installation 40 Safety Light Kit Installation 40

DEALER CHECK LISTS

Delivery Check List (Dealer’s Responsibility) Pre-Delivery Check List

(Dealer’s Responsibility)

GENERAL

Abbreviations Balance Statement Bolt Size Chart Bolt Torque Chart Flail Pattern Worksheets General Information Introduction Obtaining Replacement Manuals Specifications Table of Contents Warranty

Product 65 Replacement Parts 1

Worksheets for Contour Flail Patterns

OPERATION

Attaching Shredder to Tractor

Hydraulics (Center Cutter Option) 18 PTO Driveline 18 Pull-Type Model 18 Raising Stands 19 With Quick Hitch 17 Without Quick Hitch 18

Break-In Period Choosing the Correct Tractor Cleaning Field Operation

Flail Knives 20 Ground Speed 22 Hazard Area 22 Setting Flail Height 21 Setting Operating Height 20 Setting Outer Trailing Wheels 21 Starting the Tractor 21 Stopping the Tractor 21 Turning 22

OPERATION (CONTINUED)

Optional Equipment

Additional Rear Wheels 23 Bed Cones for 3-Point Units 23 Rubber Flaps 23

Pre-Operation Check List

(Owner’s Responsibility) Preparing for Operation Principal Components PTO Driveline Length (3-Point & 2-Point Models) Removing Shredder from Tractor Storage Tractor horsepower vs. unit width (Table 1)

SAFETY

Check Lists

Hazard Area Operator Sign-Off Record Safety Decals Safety Rules Safety Symbols Explained

SERVICE & MAINTENANCE

Balance Statement Changing Gearbox Oil Gearbox Oil Leakage Greasing Lubricants Lubrication Points Diagram Lubrication Schedule Lubrication Service Record Mounting Clutch to Shredder Ratchet Height Adjustment Replacing Flail Knives Replacing Rubber Shield Flaps Replacing Stub Shaft Servicing Rotors

Servicing Weasler Modular Friction Clutch Wheel Spacing

TROUBLESHOOTING

Delivery (Dealer’s Responsibility) 45

Pre-Delivery (Dealer’s Responsibility) 45

Pre-Operation (Owner’s Responsibility) 15

10, 11, 12

6, 7, 8, 9

Removing Components 31

Replacing Components 31

MAN0506 (Rev. 9/5/2008)

Index 65

Page 66

WARRANTY

All Models Except Mow’n MachineTM Zero-Turn Mowers

Please Enter Information Below and Save for Future Reference.

Date Purchased: ____________________________ From (Dealer): __________________________________________

Model Number: ____________________________ Serial Number: __________________________________________

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER.

All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.

The warranty periods for specific parts or conditions are listed below:

Part or

Condition

Warranted

Gearbox

Seals

Gearbox

components

Blade

spindles

Rust-through

Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other than those obtainable through WOODS.

This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.

WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.

WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of

purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or

replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues

or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture replacement parts.

No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this

Woods Equipment

All units listed below 2 years

BW1260, BW1620, BW1800, BW2400 8 years

BW240HD, BW180HD, BW180HB, BW126HB 7 years

BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240

PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2, RM660-2, RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH, TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204

RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44

RM550-2, RM660-2, RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204 3 years

BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB, BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, TS1680

Warranty. Answers to any questions regarding warranty service and locations may be obtained by contacting:

Model Number

Company

2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061 USA

800-319-6637 tel 800-399-6637 fax www.WoodsEquipment.com

Duration (from date of delivery to the original

purchaser)

6 years

5 years

3 years (1 year if used in rental or commercial applications)

10 years

F-3079 (Rev. 2/14/2011)

Page 67

WARRANTY

(Replacement Parts For All Models Except Mow’n Machine

Zero-Turn Mowers)

Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.

days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid.

WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WA R RA N TY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/ OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.

This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture replacement parts.

No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.

Answers to any questions regarding warranty service and locations may be obtained by contacting:

F-8494 (Rev. 10/3/2011)

Page 68

Woods Equipment Company

2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois 61061

800-319-6637 tel 800-399-6637 fax www.WoodsEquipment.com

©2006 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and “Tested. Proven. Unbeatable.” are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.