Wolf PW302418 Installation

I NSTALLATION I NSTRUCTIONS

P RO W ALL V ENTILATION H OODS

As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation.

Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation.

signals a situation where minor injury or product damage may occur if you do not follow instructions.

states a hazard that may cause serious injury or death if precautions are not followed.

WOLF®is a registered trademark of Wolf Appliance Company, Inc.

CONTACT INFORMATION

Wolf Customer Service: 800-332-9513

Website: wolfappliance.com

INSTALLATION REQUIREMENTS

IMPORTANT NOTE:

This installation must be completed by a qualified installer or Wolf authorized service center technician.

Installer:

Please read the entire Installation Instructions prior to installation. Save these instructions for the local inspector’s reference, then leave them with the homeowner.

Homeowner:

Please read and keep these instructions for future reference and be sure to read the entire Use & Care Information prior to use.

Any questions or problems about the installation should be directed to your Wolf dealer or Wolf Appliance Company, Inc. at 800-332-9513. You can also visit our website at wolfappliance.com.

IMPORTANT NOTE:

This appliance must be installed in accordance with National Electrical Codes, as well as all state, municipal and local codes. The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded circuit which is protected by a properly sized circuit breaker or time delay fuse. The proper voltage, frequency, and amperage ratings are listed on the product rating plate.

Record the model and serial numbers before installing the Pro wall ventilation hood. Both numbers are listed on the rating plate, located on the left wall of the hood shell.

Model Number

Serial Number

WOLF PRO WALL VENTILATION HOODS

Low-Profile Wall Hood

Low-Profile Wall Hood (R) Rail Option

24" (610) Wall Hood

24" (610) Wall Hood (R) Rail Option

27" (686) Wall Hood

27" (686) Wall Hood (R) Rail Option

Dimensions in parentheses are in millimeters unless otherwise specified.

LIST OF MATERIALS

The following is a list of materials shipped with the Wolf Pro wall ventilation hood.

Stainless steel wall hood

Transition with backdraft damper (attached inside hood—needs to be removed)

Decorative stainless steel rail and installation components—(R) model hoods only

Control knobs—two for low-profile and 24" (610) deep hoods, three for 27" (686) deep hoods

Filters and grease cups (installed in hood)

(10) #10 x 2" (51) self-tapping hex head screws

(10) 10-24 washer nuts

Installation package (taped to filters)

Installation Instructions

Use & Care Information and product registration card

Wolf logo nameplate

WOLF PRO WALL VENTILATION HOODS

IMPORTANT NOTE:

Wolf recommends that the Pro wall ventilation hood be installed 30" (762) to 36" (914) above the countertop.

Rail option (R) wall hoods come with a classic stainless steel decorative rail and stand-offs. Optional platinum or brass rails are available to match Wolf dual fuel range bezels. Contact your Wolf dealer for details.

ELECTRICAL REQUIREMENTS

Wolf Pro wall ventilation hoods require a separate, grounded 110/120 V AC, 60 Hz power supply. The service should have its own 15 amp circuit breaker. Locate the electrical supply within the shaded area shown in the Installation Specifications illustration for your specific wall hood on page 6.

You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service.

DUCT COVER

If you are installing a Wolf duct cover with the wall hood, refer to instructions on page 21 before installing the hood.

RECIRCULATING KIT

If you are installing the accessory recirculating kit, refer to the instructions included with the kit before installing the hood.

ACCESSORIES

Optional accessories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com.

INSTALLATION CONSIDERATIONS

Wolf Pro wall ventilation hoods are recommended for use with all Wolf cooking appliances.

IMPORTANT NOTE:

For optimal performance, a Pro 27" (686) deep wall hood is recommended for use with ranges and rangetops that contain a charbroiler or griddle.

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the Wolf Warranty. Refer to the Wolf Pro Ventilation Hoods Use & Care Information for warranty details, or visit the Contact/ Help section of our website, wolfappliance.com.

Make sure you have the tools and materials necessary for proper installation.

Warranty service must be performed by a Wolf authorized service center. Wolf is not responsible for service required to correct a faulty installation.

IMPORTANT NOTE:

Wolf Pro ventilation hoods are shipped without the blower assembly. Wolf internal, in-line and remote blower assemblies are available, refer to page

20. Use only a Wolf blower with the Pro wall ventilation hood.

Dimensions in parentheses are in millimeters unless otherwise specified.

INSTALLATION INSTRUCTIONS

10" (254)

OVERALL

HEIGHT

OVERALL WIDTH

4" (102)

22" (559)

OVERALL DEPTH

12"

(305)

(51)

/4" (19)

DIAMETER

OF RAIL

OVERALL WIDTH

4" (102)

24" (610)

OVERALL DEPTH

12"

(305)

18" (457)

OVERALL

HEIGHT

(51)

/4" (19)

DIAMETER

OF RAIL

OVERALL WIDTH

27" (686)

OVERALL DEPTH

12"

(305)

18" (457)

OVERALL

HEIGHT

(51)

4" (102)

/4" (19)

DIAMETER

OF RAIL

OVERALL DIMENSIONS

LOW-PROFILE WALL HOODS

Overall Widths 30" (762), 36" (914),

42" (1067) and 48" (1219)

Overall Height

10" (254)

Overall Depth (

excluding

rail) 22" (559)

Shipping Weight (shell only) 39–55 lbs

(18–25 kg)

Dimensions may vary to ±1/8" (3).

24" (610) DEEP WALL HOODS

Overall Widths 30" (762), 36" (914),

42" (1067), 48" (1219), 54" (1372),

60" (1524) and 66" (1676)

Overall Height

18" (457)

Overall Depth (

excluding

rail) 24" (610)

Shipping Weight (shell only) 67–126 lbs

(30–57 kg)

Dimensions may vary to ±1/8" (3).

27" (686) DEEP WALL HOODS

Overall Widths 30" (762), 36" (914),

42" (1067), 48" (1219), 54" (1372),

60" (1524) and 66" (1676)

Overall Height

18" (457)

Overall Depth (

excluding

rail) 27" (686)

Shipping Weight (shell only) 69–128 lbs

(31–58 kg)

Dimensions may vary to ±1/8" (3).

Low Profile Wall Hood

shown with (R) rail option

24" (610) Deep Wall Hood

shown with (R) rail option

27" (686) Deep Wall Hood

shown with (R) rail option

WOLF PRO WALL VENTILATION HOODS

30" TO 36"

(762–914)

TO COUNTERTOP

30" TO 36"

(762–914)

TO COUNTERTOP

10" (254) 18" (457)

HEIGHT

OF HOOD

22" (559) 24" (610)

DEPTH OF HOOD

WIDTH OF HOOD

NOTE: Low-profile and 24" (610) deep wall hoods have a vertical or horizontal discharge; discharge direction varies with blower model.

(152)

(127)

LOCATION OF ELECTRICAL

30" TO 36"

(762–914)

TO COUNTERTOP

30" TO 36"

(762–914)

TO COUNTERTOP

18" (457)

HEIGHT

OF HOOD

27" (686)

DEPTH OF HOOD

WIDTH OF HOOD

(152)

(127)

LOCATION OF ELECTRICAL

NOTE: 27" (686) deep wall hoods are vertical discharge only.

INSTALLATION SPECIFICATIONS

Low-Profile and 24" (610) Deep Wall Hoods

27" (686) Deep Wall Hoods

Dimensions in parentheses are in millimeters unless otherwise specified.

INSTALLATION INSTRUCTIONS

INSTALLATION SPECIFICATIONS

The following chart provides dimensions specific to each wall hood model. These dimensions are critical for proper installation. Also refer to the illustration below.

Low-Profile Wall Hoods

Model (A) (B) (C) (D)

W302210I 30" (762) 71/2" (191) 15" (381) 411/16" (119)

W362210I 36" (914) 71/2" (191) 18" (457) 411/16" (119)

W362210 36" (914) 71/2" (191) 18" (457) 411/16" (119)

W422210 42" (1067) 71/2" (191) 21" (533) 411/16" (119)

W482210 48" (1219) 71/2" (191) 24" (610) 411/16" (119)

24" (610) Deep Wall Hoods

Model (A) (B) (C) (D)

W302418 30" (762) 91/2" (241) 15" (381) 513/16" (148)

W362418 36" (914) 91/2" (241) 18" (457) 513/16" (148)

W422418 42" (1067) 91/2" (241) 21" (533) 513/16" (148)

W482418 48" (1219) 91/2" (241) 24" (610) 513/16" (148)

W542418 54" (1372) 91/2" (241) 27" (686) 513/16" (148)

W602418 60" (1524) 91/2" (241) 30" (762) 513/16" (148)

W662418 66" (1676) 91/2" (241) 33" (838) 513/16" (148)

27" (686) Deep Wall Hoods

Model (A) (B) (C) (D)

W302718 30" (762) 91/2" (241) 15" (381) 513/16" (148)

W362718 36" (914) 91/2" (241) 18" (457) 513/16" (148)

W422718 42" (1067) 91/2" (241) 21" (533) 513/16" (148)

W482718 48" (1219) 91/2" (241) 24" (610) 513/16" (148)

W542718 54" (1372) 91/2" (241) 27" (686) 513/16" (148)

W602718 60" (1524) 91/2" (241) 30" (762) 513/16" (148)

W662718 66" (1676) 91/2" (241) 33" (838) 513/16" (148)

Letters correspond to those in the illustration.

HEIGHT OF

TRANSITION

TO CENTER

OF TRANSITION

TO CENTER

OF TRANSITION

WIDTH

OF HOOD

LOW-PROFILE AND 24" (610) HOODS

STEP 1: INSTALL DUCTWORK

IMPORTANT NOTE:

Wolf recommends that the Pro wall ventilation hood be installed 30" (762) to 36" (914) above the countertop.

IMPORTANT NOTE:

Consult a qualified HVAC Engineer for specific ducting applications.

IMPORTANT NOTE:

All Wolf Pro wall hoods must exhaust to the outdoors except when used with the accessory recirculating kit. Always use metal ducting. Do not use flex ducting.

Decide where the ductwork will run between the hood and the outside. A straight, short duct run will allow the hood to perform more efficiently. Limit the number of elbows and transitions to as few as possible. Long duct runs, elbows and transitions will reduce the performance of the hood. Wolf recommends the maximum linear duct run be no greater than 50' (15 m). The low-profile and 24" (610) deep wall hoods have an adjustable discharge that can run vertically or horizontally.

Horizontal discharge is only applicable on low-profile wall hoods (excluding W302210I and W362210I) used with a remote blower. In-line blowers and WBLOWER-60INT are not for use in horizontal discharge applications with a low-profile wall hood.

Horizontal discharge is applicable on 24" (610) deep wall hoods used with WBLOWER-60INT, WBLOWER-120INT or any Wolf remote blower. In-line blowers and WBLOWER-90INT are not for use in horizontal discharge applications.

IMPORTANT NOTE:

There is a possibility of noise issues if there is a short duct run coupled with a remote blower.

To reduce the risk of fire, use only metal ductwork.

WOLF PRO WALL VENTILATION HOODS

DUCTWORK INSTALLATION

THROUGH ROOF

22" (559)

DEPTH OF HOOD

8" ROUND DUCT

SOFFIT OR CABINET

OR DUCT COVER

REMOTE BLOWER

*HORIZONTAL DISCHARGE APPLICABLE ON LOW-PROFILE WALL HOODS

(EXCLUDING W302210I AND W362210I) USING A REMOTE BLOWER. LOW-PROFILE WALL

HOODS WITH AN INTERNAL OR IN-LINE BLOWER MUST USE VERTICAL DISCHARGE.

DUCTWORK INSTALLATION

THROUGH WALL

DISCHARGE COLLAR

HORIZONTAL DISCHARGE*

VERTICAL DISCHARGE

TRANSITION

/4"W x 41/4"D TO 8" ROUND

/8"H (INCLUDING FLANGES)

30" TO 36"

(762–914)

COUNTERTOP

TO BOTTOM OF

VENTILATION HOOD

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

10" (254)

HEIGHT OF HOOD

WALL HOOD

ROOF CAP OR REMOTE BLOWER –

TRANSITION FROM 8" (203) TO 10" (254) DUCT

REQUIRED FOR REMOTE BLOWER

Ducting options for low-profile wall hoods

+ 16 hidden pages