Wolf PL342212, PL341912 Installation Guide

PRO HOOD LINER
INSTALLATION GUIDE
SPECIFICATIONS, INSTALLATION, AND MORE
PRO HOOD LINER
Contents
3 Pro Hood Liner
3 Safety Precautions
6 Installation
10 Blower Specications
11 Troubleshooting
Features and specications are subject to change at any time without notice. Visit wolfappliance.com/specs for the most up-to-date information.
Important Note
To ensure this product is installed and operated as safely and efciently as possible, take note of the following types of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
2 | Wolf Customer Care 800.222.7820
PRO HOOD LINER
Product Information
Important product information, including the model and serial number, are listed on the product rating plate. The rating plate is located inside the right wall of the hood liner (lters need to be removed). Refer to the illustration below.
If service is necessary, contact Wolf Factory Certied Service with the model and serial number. For the name of the nearest Wolf Factory Certied Service or for questions regarding the installation, visit the Support & Service section of our website, wolfappliance.com, or call Wolf Customer Care at 800-222-7820.
RATING PLATE
Rating plate location
IMPORTANT INSTRUCTIONS
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY, OBSERVE THE FOLLOWING:
Installation work and electrical wiring must be
done by qualied person(s) in accordance with all applicable codes and standards, including re­rated construction.
Two installers are recommended due to the size
and weight of the pro hood.
Install the pro hood only with a blower manufac-
tured by Wolf.
When cutting or drilling into the wall or ceiling,
do not damage electrical wiring and other hidden utilities.
Ducted fans must always be vented to the
outdoors.
CAUTION
To reduce the risk of re and properly exhaust air, be certain to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.
wolfappliance.com | 3
SPECIFICATIONS
Installation Requirements
Install the hood 30" (762) to 36" (914) from the bottom of the hood to the countertop.
BLOWER ASSEMBLIES
Pro Hood Liners require an internal, in-line, or remote blower assembly, avail able through an authorized Wolf dealer. For local dealer information, visit the nd a showroom section of our website, wolfappliance.com. Refer to specic installa­tion instructions provided with each blower assembly.
DECORATIVE HOOD
The decorative hood can be created out of wood, plaster, tile, or metal. The shape of the hood is not critical, however, the decorative hood and liner must t together at the bottom edge in both width and depth. The height of the liner does not need to accommodate the entire height of the decora­tive hood.
3
The lower stainless steel. The bottom edge of the liner should not extend more than
/4" (19) of the liner’s 4" (102) reveal is nished
3
/4" (19) below the decorative hood.
Ducting
WARNING
To reduce the risk of re, use only metal ducting.
IMPORTANT NOTE: Consult a qualied HVAC professional
for specic installation and ducting applications.
Pro hoods accommodate a 10" rigid metal ducting.
A straight, short duct run allows the hood to perform most efciently. If the duct run exceeds 50' blower may be required to maintain proper air ow.
Internal and in-line blowers require a roof or wall cap. Connect ducting to the cap or to the remote blower and work back towards the hood. Use sheet metal screws and high-temperature duct tape to seal joints between ducting sections.
Pro hoods include a backdraft damper. Local codes may require the use of an additional backdraft and/or make-up air damper. Contact your local HVAC professional for spe­cic requirements.
A make-up air damper is available through an authorized Wolf dealer. For local dealer information, visit the nd a showroom section of our website, wolfappliance.com.
(254) round duct. Use only
(15 m), a higher CFM
4 | Wolf Customer Care 800.222.7820
SPECIFICATIONS
Discharge
Pro Hood Liners have a vertical discharge. Refer to the illustration below.
2" (54)
Vertical discharge
55/8"
(143)
Electrical Requirements
Installation must comply with all applicable electrical codes.
Locate the electrical supply as shown in the illustration below. A separate circuit servicing only this appliance is required.
ELECTRICAL REQUIREMENTS
Electrical Supply grounded, 120 VAC, 60 Hz
Service 15 amp dedicated circuit
DECORATIVE HOOD
E
121/2"
(318)
30" (762) TO 36" (914) BOTTOM EDGE TO COUNTERTOP
75/8"
(
194
)
Electrical location
RATING PLATE
Rating plate location
wolfappliance.com | 5
INSTALLATION
Hood Preparation
Remove the lters prior to installation. Remove the center lter rst, if applicable. To remove, press the lter upward, then rotate the bottom downward. Refer to the illustration below.
Filters
Installation
WARNING
Wall framing must be able to support the weight of the hood and internal blower, if applicable.
1 Refer to the illustration below for typical wall framing.
BLOCKING MOUNTING
5"
(127)
BACK PANEL
Wall framing (typical)
C
L
HOLE
MOUNTING
HOLE
10
(273)
3
/4
"
6 | Wolf Customer Care 800.222.7820
INSTALLATION
Installation
2 Remove the transition from inside the hood by removing
the hold-down brackets. Remove the shipping material from the damper. Refer to the illustration below.
3 Mount the transition and hold-down brackets to the top
of the hood using the existing screws. Refer to the illus­tration below.
TRANSITION
TRANSITION
Transition position (shipping) Transition mounting
HOLD-DOWN
BRACKET
4 Remove the electrical box from the inside of the hood.
Refer to the illustration below.
5 For internal blowers, install the blower prior to mounting
the hood. Refer to the instructions provided with the blower.
6 Lift the hood into position and insert Romex
®
wire(s) into the electrical knockout and secure with a UL or C/UL approved connector (not provided).
7 Secure the hood to the wall structure with the provided
screws and washers.
8 Connect the ducting to the transition and secure with
duct sealing tape.
ELECTRICAL BOX
(INSIDE HOOD)
Location of electrical box
wolfappliance.com | 7
INSTALLATION
Electrical Connections
WARNING
Before making electrical connections, verify the power is turned off at the service panel.
IMPORTANT NOTE: Refer to installation instructions pro-
vided with the blower assembly.
INTERNAL BLOWER
1 Connect black to black and white to white with the
provided connectors, and connect the green/bare wire to the ground screw.
2 Verify all wires are secure and not pinched, and reinstall
the box.
3 Plug the blower power cord into the receptacle inside
the hood. Refer to the illustration below.
4 Turn on the power to the hood and verify light and
blower operation.
IN-LINE/ REMOTE BLOWER
1 Connect the home supply. Connect black to black and
white to white with the provided connectors, and con­nect the green/bare wire to the ground screw.
2 Connect the blower supply to the power cord provided
with the blower. Connect black to black, white to white, and the green/bare wire to the ground screw.
3 Verify all wires are secure and not pinched, and reinstall
the box.
4 Plug the blower power cord into the receptacle inside
the hood. Refer to the illustration below.
5 Turn on the power to the hood and verify light and
blower operation.
RECEPTACLE
RECEPTACLE
Electrical connections
Electrical connections
8 | Wolf Customer Care 800.222.7820
INSTALLATION
Complete the Installation
FILTERS
Orient the lters with the lines running vertically. To install, place the top edge of the lter against the spring, press upward and rotate the bottom into position. Slide the outer lters over to reinstall the center lter, if applicable. Refer to the illustration below.
Filters
LIGHT BULBS
A suction-cup-style light bulb changer is provided with the hood. To install, use the changer to push the bulb into the receptacle and rotate counterclockwise one-quarter turn. Refer to the illustration below.
LIGHT BULB
CHANGER
Light bulb
wolfappliance.com | 9
BLOWER SPECIFICATIONS
28
29 29
11
Blower Dimensions
IN-LINE BLOWERS
243/8"
(619)
3
/4"
(298)
181/2"
(470)
41/2"
(114)
211/2"
(546)
121/4"
(311)
18"
(457)
12"
(305)
22"
(559)
8"
(203)
24
(632)
18"
(457)
7
/8
"
600 CFM in-line blower
REMOTE BLOWERS
3
/4
20
"
24
(629)
(527)
3
/4
"
1
(718)
/4
15
(394)
"
10" (254)
DIAMETER
1
/2
"
14"
(356)
600/900 CFM remote blower
24
(622)
1
/2
3
4
(121)
1100 CFM in-line blower
18" (457)
10"
1
/2
"
(749)
14
"
/4
"
(375)
10" (254)
DIAMETER
3
/4
"
1
/8
10
"
(257)
22"
(559)
1200 CFM remote blower
(254)
29
(749)
7
(184)
1
/2
"
(749)
1
/2
"
1
/4
"
14
(375)
10" (254)
DIAMETER
3
/4
"
3
/8
10
"
(264)
1500 CFM remote blower
25"
(635)
21" (533)
10"
(254)
29
(749)
7
(184)
1
/2
"
1
/4
"
10 | Wolf Customer Care 800.222.7820
TROUBLESHOOTING
Troubleshooting
IMPORTANT NOTE: If the hood does not operate properly,
follow these troubleshooting steps:
Verify electrical power is supplied to the hood.
Verify proper wiring connections.
If the hood does not operate properly, contact Wolf
Factory Certied Service. Do not attempt to repair the hood. Wolf is not responsible for service required to correct a faulty installation.
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries. All other trademarks are property of their respective owners in the United States and other countries.
wolfappliance.com | 11
WOLF APPLIANCE, INC. P.O. BOX 44848 MADISON, WI 53744 WOLFAPPLIANCE.COM 800.222.7820
0000000 REV-A 8/2019
Loading...