Wolf PI363418(R), PI423418(R), PI543418(R), PI663418(R) Installation Guide
I NSTALLATION I NSTRUCTIONS
P RO I SLAND V ENTILATION H OODS
READ AND SAVE THESE INSTRUCTIONS
As you follow these instructions, you will
notice WARNING and CAUTION symbols.
This blocked information is important for the
safe and efficient installation of Wolf equipment. There are two types of potential
hazards that may occur during installation.
Another footnote we would like to identify is
IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
states a hazard that may cause serious
injury or death if precautions are not
followed.
WOLF®is a registered trademark of Wolf Appliance, Inc.
CONTACT
INFORMATION
Wolf Customer
Service:
800-332-9513
Website:
wolfappliance.com
A)
Never leave surface units unattended at
high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
B)
Always turn hood ON when cooking at high
heat or when flambéing food (Crêpes Suzette,
Cherries Jubilee, Peppercorn Beef Flambé).
C)
Clean ventilating fans frequently. Grease
should not be allowed to accumulate on fan
or filter.
D)
Use proper pan size. Always use cookware
appropriate for the size of the surface
element.
WARNING – TO REDUCE THE RISK OF A
RANGE TOP GREASE FIRE:
1)
SMOTHER FLAMES with a close-fitting lid,
baking sheet or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT BURNS.
IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL THE FIRE
DEPARTMENT.
2)
NEVER PICK UP A FLAMING PAN—You
may be burned.
3)
DO NOT USE WATER, including wet dishcloths or towels—This could cause a violent
steam explosion.
4)
Use an extinguisher ONLY IF:
A. You own a Class ABC extinguisher and
you know how to operate it.
B. The fire is small and contained in the
area where it started.
C. The fire department has been called.
D. You can fight the fire with your back to
an exit
*Based on "Kitchen Fire Safety Tips" published
by NFPA.
WARNING – TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE, OBSERVE
THE FOLLOWING*:
3
WOLF PRO ISLAND VENTILATION HOODS
Dimensions in parentheses are in
millimeters unless otherwise specified.
Rating plate location
Location of rating plate
inside back wall
RATING PLATE
INFORMATION
Model Number
Serial Number
INSTALLATION REQUIREMENTS
IMPORTANT NOTE:
This installation must be
completed by a qualified installer or Wolf
authorized service center technician.
Installer:
Please read the entire Installation
Instructions prior to installation. Save these
instructions for the local inspector’s reference, then leave them with the homeowner.
Homeowner:
Please read and keep these
instructions for future reference and be sure
to read the entire Use & Care Information
prior to use.
Any questions or problems about the installation should be directed to your Wolf dealer or
Wolf Appliance, Inc. at 800-332-9513. You can
also visit our website at wolfappliance.com.
IMPORTANT NOTE:
This appliance must be
installed in accordance with National Electrical
Codes, as well as all state, municipal and local
codes. The correct voltage, frequency and
amperage must be supplied to the appliance
from a dedicated, grounded circuit which is
protected by a properly sized circuit breaker or
time delay fuse. The proper voltage, frequency,
and amperage ratings are listed on the product
rating plate.
Record the model and serial numbers before
installing the hood. Both numbers are listed on
the rating plate, located on the inside back wall
of the hood shell. Refer to the illustration
below.
A)
Installation work and electrical
wiring must be done by qualified
person(s) in accordance with all
applicable codes and standards,
including fire-rated construction.
B)
When cutting or drilling into wall
or ceiling, do not damage electrical
wiring and other hidden utilities.
C)
Ducted fans must always be
vented to the outdoors.
WARNING – TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
The hood motor has a thermal overload
which will automatically shut off the
motor if it becomes overheated. The
motor will restart when it has cooled
down. If the motor continues to shut off
and restart, have the hood serviced.
4
WOLF PRO ISLAND VENTILATION HOODS
LIST OF MATERIALS
The following is a list of materials shipped
with the Wolf Pro island ventilation hood.
Stainless steel island hood
Transition with backdraft damper (attached
inside hood—needs to be removed)
Decorative stainless steel rails and installation components—(R) model hoods only
Two control knobs
Filters and grease cups (installed in hood)
(16) #10 x 2" (51) self-tapping hex head
screws (number of screws varies with the
width of the island hood)
(4)
1
/4" x 3" (76) lag screws
(4)
1
/4" (6) ID x 3/4" (16) OD washers
Installation package
Installation Instructions
Use & Care Information and product
registration card
Wolf logo nameplate
Island Hood
Island Hood
(R) Rail Option
INSTALLATION CONSIDERATIONS
Wolf Pro island ventilation hoods are
recommended for use with all Wolf cooking
appliances.
Proper installation is the responsibility
of the installer. Product failure due to
improper installation is not covered
under the Wolf Warranty. Refer to the Wolf
Pro Ventilation Hoods Use & Care
Information for warranty details, or visit
the Contact/ Help section of our website,
wolfappliance.com.
Make sure you have the tools and materials
necessary for proper installation.
Warranty service must be performed by a
Wolf authorized service center. Wolf is not
responsible for service required to correct a
faulty installation.
IMPORTANT NOTE:
Wolf Pro ventilation
hoods are shipped without the blower
assembly. Wolf internal, in-line and remote
blower assemblies are available; refer to pages
15–16. Use only a Wolf blower with the Pro
island hood.
IMPORTANT NOTE:
Wolf recommends that
the Pro island ventilation hood be installed
30" (762) to 36" (914) above the countertop.
Rail option (R) island hoods come with classic
stainless steel decorative rails and stand-offs
on both sides of the hood. Optional platinum
or brass rails are available to match Wolf dual
fuel range bezels. Contact your Wolf dealer for
details.
If you are installing an optional duct cover with
the Pro island hood, refer to instructions on
page 9 before installing the hood.
When performing installation, servicing
or cleaning the unit, it is recommended
to wear safety glasses and gloves.
5
Dimensions in parentheses are in
millimeters unless otherwise specified.
INSTALLATION INSTRUCTIONS
ELECTRICAL REQUIREMENTS
Wolf Pro island ventilation hoods require a
separate, grounded 110/120 V AC, 60 Hz power
supply. The service should have its own 15
amp circuit breaker. Locate the electrical
supply through the top of the hood. Refer to
the Installation Specifications illustration
below.
You must follow all National Electrical Code
regulations. In addition, be aware of local
codes and ordinances when installing your
service.
INSTALLATION SPECIFICATIONS
TOP WIDTH
SUBTRACT 18" (457) FROM OVERALL WIDTH
18" (457)
OVERALL
HEIGHT
OVERALL WIDTH
34" (864)
OVERALL DEPTH
13"
(330)
4" (102)
2"
(51)
3
/4" (19)
DIAMETER
OF RAIL
2"
(51)
OVERALL DIMENSIONS
PRO ISLAND HOODS
Overall Widths 36" (914), 42" (1067),
54" (1372) and 66" (1676)
Overall Height
18" (457)
Overall Depth (
excluding
rails) 34" (864)
Shipping Weight (shell only) 95–168 lbs
(43–76 kg)
Unit dimensions may vary to ±1/8" (3).
Pro island hood shown with (R) rail option.
18" (457)
HEIGHT
OF HOOD
34" (864)
DEPTH OF HOOD
WIDTH OF HOOD
LOCATION OF ELECTRICAL SUPPLY
THROUGH TOP OF HOOD
30" TO 36"
(762–914)
TO COUNTERTOP
30" TO 36"
(762–914)
TO COUNTERTOP
6
WOLF PRO ISLAND VENTILATION HOODS
INSTALLATION SPECIFICATIONS
The illustration and chart below provides
dimensions critical for proper installation of
the Wolf Pro island ventilation hood.
34" (864)
DEPTH OF
HOOD
A
WIDTH OF
HOOD
B
WIDTH OF
TOP PLATE
C
HEIGHT OF
TRANSITION
D
TO CENTER
OF TRANSITION
6
1
/2
"
(165)
13"
(330)
10" (254)
Pro Island Hoods
Model (A) (B) (C) (D)
PI363418(R) 36" (914) 18" (457) 7" (178) 9" (228)
PI423418(R) 42" (1066) 24" (610) 7" (178) 12" (304)
PI543418(R) 54" (1371) 36" (914) 7" (178) 18" (457)
PI663418(R) 66" (1676) 48" (1219) 7" (178) 24" (610)
Letters correspond to those in the illustration.
To reduce the risk of fire and electric
shock, install this ventilation hood only
with a blower manufactured by Wolf.
Blower model numbers are listed on
page 16.
Loading...