Wolf PHORIZDIS36W, PHORIZDIS54W, PHORIZDIS42W, PHORIZDIS48W, PHORIZDIS60W Installation Instructions Manual

WOLF PRO-SERIES WALL HOOD HORIZONTAL
DISCHARGE INSTALLATION INSTRUCTIONS

811357 / Rev A/ June, 2007

Horizontal Discharge Kit Contains:

QTY

DESCRIPTION

1 Back Panel with PEM studs
2 Mounting Brackets
1 Installation Hardware (810555)
1 Instruction Sheet

Horizontal Discharge Accessory Kits are designed for
use with Wolf Pro-Series Wall Hood Model Numbers:

24" DEEP 27" DEEP
HOODS HOODS

PW302418(R) PW302718(R)
PW362418(R) PW362718(R)
PW422418(R) PW422718(R)
PW482418(R) PW482718(R)
PW542418(R) PW542718(R)
PW602418(R) PW602718(R)
PW662418(R) PW662718(R)

Horizontal Discharge Kit Model Numbers

• PHORIZDIS30W (811088) – For use with PW302418
& PW302718

• PHORIZDIS36W (811089) – For use with PW362418
& PW362718

• PHORIZDIS42W (811090) – For use with PW422418
& PW422718

• PHORIZDIS48W (811091) – For use with PW482418
& PW482718

• PHORIZDIS54W (811092) – For use with PW542418
& PW542718

• PHORIZDIS60W (811093) – For use with PW602418
& PW602718

• PHORIZDIS66W (811094) – For use with PW662418
& PW662718

PROCEDURE

1. First, ensure that there is adequate wall framing

available for the hood to mount securely to (See
Figure 1).

Page 1 of 2

2. Cut opening into wall. This opening must be large
enough for the supplied transition or custom duct
work to fit through when attached to the wall hood
(See Figure 2).

3. Install the mounting brackets onto the wall and
ensure that they are attached to wall framing studs.
These brackets will aid in mounting the hood onto
the wall by temporarily holding the hood in place for
you (See Figure 3).

4. Remove the factory installed back panel from the
hood by removing the screws on the top and back
sides of the wall hood (save the screws as they will
be used again). Then remove the electrical junction
box from the factory supplied back panel and save
the nuts holding the junction box on because they
will needed in order to transfer the junction box over
to the new horizontal discharge kit back panel (See
Figure 4).

5. Assemble the junction box removed in step 4 onto
the horizontal discharge back panel. If an internal
blower will be used with the hood, mount the blower
assembly to the horizontal discharge back panel
using the provided #10-24 KEPS nuts and the blow­er installation instructions (See figure 5).

6. Next, assemble the new horizontal discharge back
panel (and internal blower assembly if applicable)
onto the hood using the screws removed in step 3.

7. Attach the transition or custom duct work to the out­let of the ventilation hood.

8. Mount the hood onto the wall by utilizing the rectan­gle cut outs in the back panel and hanging the hood
on the mounting brackets.

9. Use the rows of holes provided (shown in figure 3)
to drive mounting screws into the wall framing to
properly support the hood.

10. Connect electrical wiring per the ventilation hood
installation instructions.

Hood must be anchored to wall framing to provide
proper support

811357 / Rev A/ June, 2007

Page 2 of 2

A - 17-1/2” to horizontal framing stud center from bottom of hood
B - 9” Horizontal framing stud centers
C - 13-1/8” to center of framing stud from center of hood
D - 26-1/4” Framing Stud centers
E - Wall Opening see Figure 2 for size and location

Width of Unit

Suggested Wall Framing Layout

A

B

C

D

E

Figure 1

Wall Hole Cut-Out

A - Wall opening for duct work
B - 22-1/2” Hole in wall center of hood
C - Blower Discharge opening in back panel
D - 10-3/4” high hole in wall
E - 17-1/2” to top of hole in wall

A

B

C

D

E

Figure 2

Hood Mounting Illustration

A - 15-1/16" to top mounting bracket hole from bottom of hood
B - Use this row of holes to attach hood to wall framing studs
C - 13 1/8" to mounting bracket hole from center of hood
D - 26 1/4" mounting bracket centers
E - Must mount brackets to wall framing studs

A

B

C

D

E

B

Figure 3

Back Panel Removal

Figure 4

Internal Blower Mounting

Figure 5

Hood Side View

Transition
0 10-1/4”

12-1/4”

9”

Figure 6