WHIRLPOOL AMD 351 GWH12MB-K3DND8 User Manual

BEFORE USING THE APPLIANCE

To make the most out of your new appliance, please read the user instructions carefully and keep them handy for future consultation.

SAFETY PRECAUTIONS

• The Installation and service/repair must be performed by a qualified technician, in compliance with the producer's instructions and following local safety norms. Do not repair or replace any parts of the appliance unless it is specifically written in the user instructions.

• Do not pull the power supply cord to remove it from the socket. Do not twist or press the power supply cord, and make sure it is not broken.

• Do not touch the power plug, circuit breaker and emergency button when your hands are wet.

• Do not insert your fingers or foreign substances into the air inlet/outlet of indoor&outdoor unit.

• Never block the air inlet or outlet of indoor and outdoor unit.

• Physically or mentally disabled people, children and people without any experience with the product are only allowed to use the appliance if they have had specific training on how to operate the appliance by a person responsible for their security and well-being. The appliance is not intended for use by disabled people and very young children without supervision.

• Children should be supervised to ensure that they do not play with the appliance (including remote control).

AIR CONDITIONER PRECAUTIONS

Please strictly follow the below instructions:

• Long and direct exposure to cool air might be harmful to health. It is advisable to set the louvers in order to avoid direct cool air and deflect it within the room.

• Upon malfunctioning first turn the appliance off by pressing the ON/OFF button on the remote control, then disconnect it from power supply.

• Do not switch the appliance on and off too often as this can damage the appliance.

• Do not place any objects on the outdoor unit.

• Disconnect the air conditioner from the power supply if it is to be left unused for a long period of time or during a thunder/lightning storm.

• This product contains Fluorinated Greenhouse Gases covered by the Kyoto Protocol, the refrigerant gas being in a hermetically sealed system. Refrigerant gas: R410a has a Global Warming Potential (GWP) 1975.

• This appliance has been made of recyclable or re-usable material. Scrapping must be carried out in compliance with local waste disposal regulations. Before scrapping it, make sure to cut off the mains cord so that the appliance cannot be re-used.

• For more detailed information on handling and recycling of this product, contact your local authorities who deal with the separate collection of rubbish or the shop where you bought the appliance.

SCRAPPING OF PACKAGING

• The packaging can be 100% recycled as confirmed by the recycling symbol . The various parts of the packaging must not be dispersed in the environment, but must be scrapped in line with local authority regulations.

SCRAPPING OF APPLIANCE

• This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).

• By ensuring that this product is disposed of correctly, you will help to prevent potentially negative consequences for the environment and for human health.

• The symbol on the product or on the documents accompanying the product indicates that this appliance should not be treated as household waste, but must be given to the appropriate local gathering place where electric and electronic appliances are stored and recycled.

SAFEGUARDING THE ENVIRONMENT

PRODUCT DESCRIPTION

Indoor unit

1. Air Intake

2. Front Panel

3. Display panel

4. Air Outlet

5. Electrical box

6. On/off switch

7. Vertical Adjustment Louver

8. Horizontal Adjustment Louver

9. Air Filter

10. Remote Control

Outdoor unit

11. Air Intake

12. Pipes and Power Connection Cord

13. Drain Hose

14. Air Outlet

Images in the user instructions are based on external views of standard models, shape and design vary according to the model.

CONTROL PANEL DISPLAY INDICATORS DESCRIPTION

Temperature indicator (1)

Displays set and room temperature.

Running indicator (2)

It lights up in red when connecting to power supply. It lights up in white during operation.

Heating indicator (3)

It lights up during heating mode.

Cooling indicator (4)

It lights up during cooling mode.

Dehumidifying indicator (5)

It lights up during Dehumidifying mode

Signal Receptor (6)

REMOTE CONTROL FUNCTIONS AND INDICATORS

1. ON/OFF BUTTON

Starts and/or Stops the appliance by pressing this button.

2-3. TEMPERATURE SETTING BUTTONS

Used to set temperature. Used to set time for clock. Used to set time in timer mode.

4. MODE BUTTON

Used to select the operation mode.

5. BUTTON

Used to set or cancel 6th sense operation.

6. BUTTON

Used to set or cancel around U operation.

7. FAN BUTTON

Used to select fan speed in sequence auto, high, medium or low.

8. SWING BUTTON

Used to stop or start vertical adjustment louver swinging and sets the desired up/down airflow direction.

9. POWER SAVE BUTTON

Used to set or cancel power save operation

10-11. TIMER ON and TIMER OFF BUTTON

Used to set or cancel the timer operation.

12. DISPLAY ON/OFF BUTTON

Used to turn on/off display light on indoor unit.

13. INFO °C BUTTON

Used to display room temperature or set temperature on indoor unit control panel.

14. AUTO CLEAN BUTTON

Used to set or cancel auto clean operation.

15. CLOCK BUTTON

Used to set the current time.

16. SLEEP BUTTON

Used to set or cancel Sleep operation.

17. JET BUTTON

Used to start or stop the fast cooling and heating operation.

INDICATOR SYMBOLS ON RC DISPLAY

Cooling indicator

Dehumidifying indicator

Fan only indicator

Heating indicator

Auto fan speed

High fan speed

Medium fan speed

Low fan speed

Auto clean indicator

Swing indicator

Lock indicator

indicator

Sleep indicator

Around U indicator

Jet indicator

Signal transmission

Display set timer

Display current time

Temperature display

Set temperature dispaly indicator

Room temperature display indicator

Front panel display light on indicator

FAN

°F

STORAGE AND TIPS FOR USING THE REMOTE CONTROL

How to insert the batteries

1. Unscrew the screw on the battery cover. Gently press down on the battery cover and push in the direction of the arrow to remove, as shown.

2. Insert 2 AAA batteries (1.5V) into the compartment. Ensure that "+" and "-" polarity is correctly positioned.

3. Close the battery cover on the remote control. Put back the screw on the remote control and fasten it tightly.

How to remove the batteries

Unscrew the screw and remove the battery cover in the direction of the arrow. Press the positive pole of the battery softly with your fingers, then draw the batteries out of the compartment. All this should be done by adults, children are forbidden to remove the batteries from the remote control in order to avoid danger of swallow.

Disposal of the batteries

Please discard the batteries as sorted municipal waste at the accessible collection point.

Precautions

• When replacing the batteries, do not use new batteries with old batteries, or different types of batteries as this may cause the remote control to malfunction.

• If you do not expect to use the remote control for some time, take the batteries out to prevent leakage of battery acid in the remote control.

• Operate the remote control within effective range. Keep the remote control at least 1 meter from any TV set or HI-FI equipment.

• If the remote control does not work normally, take the batteries out and reinstall after 30 seconds. If it still does not work install new batteries.

• To operate the appliance by remote control, point the remote control at the receiving device on the indoor unit, to ensure receiving sensibility.

• To send a message from remote control, the

symbol will flash for 1 second. On receipt of the message, the appliance will emit a beep.

• The remote control will operate the air conditioner at a distance of up to 7m.

• Each time the batteries are replaced in the remote control, the remote control is pre-set at 6th Sense mode.

Signal receptor

OPERATING MODE DESCRIPTION

General Operation:

1. Turning on

Press button, when the appliance receives the signal, the RUNNING indicator on indoor unit dispaly lights up. During mode changes wait a few seconds and repeat the operation if the appliance does not respond at once. When setting the heating operation, air flow will start after 2-5 minutes.

2. Selecting mode

Each time the Mode button is pressed, the operation mode is changed in sequence:

6th SENSE mode

COOLING mode

DEHUMIDIFYING mode

FAN only mode

HEATING mode

3. Setting FAN speed

Each time the Fan button is pressed, the fan speed is changed in sequence:

Auto fan speed

Low fan speed

Medium fan speed

High fan speed Only low fan speed is available under Dehumidifying mode.

4. Setting temperature

Press once to raise temperature setting by 1 °C Press once to raise temperature setting by 1 °C

When pressing or button and hold it down, the number will change rapidly. Range of available set temperature: 16°C~30°C

*Note: In 6th SENSE mode the temperature cannot be set.

FAN

+ 16 hidden pages