Whirlpool ADPU8783 A PCTR 6S IX INSTRUCTION FOR USE

Quick reference guide				Chart

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

WASH TIME DISPLAY

RINSE AID INDICATOR

SALT INDICATOR

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected

When lit (at the end of the cycle),

When lit (at the end of the cycle), the

it indicates the time remaining until program start (h.00) - below 1h (0:min).

the rinse aid dispenser needs to

salt reservoir needs to be refilled.

5019 396 03671

If “Fx Ey” messages appears on the display, see page 9 - chapter “What to do if...”.

be refilled.

PROGRAM

SELECTION BUTTON

Push “P” button (repeatedly) until selected program number is shown on the display (P1...Px) - see “Table of programs” - next page).

POWER CLEAN

Thanks to the additional power jets this option provides a more intensive and powerful wash in the lower rack, in the specific area. This option is recommended for washing pots and casseroles (see page 7). Press this button to activate Power Clean (the indicator lights up). For non Power Clean loading to achieve best cleaning performances and resources optimization, Power Clean should be switched off.

HALF LOAD BUTTON

Half load cycle can be used for the upper or lower rack. Select the required program then press the “Half Load” button - the light comes on. Turns off at the end of the program.

The “Half Load” option can be used with the programs indicated in the table of programs.

TABLET SETTING

This setting allows to optimize the cycle performances according the type of detergent used. Push the Tablet button for 3 seconds (until the indicator lights up)

if you are using the combined detergents in tablet (rinse aid, salt and deteregent in 1 dose). If you are using powder detergent or liquid detergent, the Tablet indicator on the control panel has to be off.

DELAYED START BUTTON

Push the button (repeatedly) to delay the start of the program. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after

24 restarts from 0. Then press the START button. The dishwasher will start after the set time.

START/RESUME BUTTON

Push this button to start the selected program: the indicator lights up and goes off at the end of the program.

When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks.

To resume the cycle close the door and push Start button again.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display).

If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process).

Whirlpool is a registered trademark of Whirlpool USA	GB -1-

Quick reference guide

Chart

P1

P2

P3

P4

P5

P6

P7

P8

P9

P10

		Table of programs					Consumption
					Deter-				Drying
			Available
	Programs			Loading instructions	gent	Litres	kWh	Minutes 1)	Phase
			options
				Use for normal soiled dishes with dried-on food. Senses the
	6th Sense Power			level of soiling on the dishes and adjusts the program
		40-70°C	Delay	accordingly. When the sensor is detecting the soil level an	X	7-14	1.00-1.65	80-165	Full
	Clean		Half Load	animation appears in the display and the cycle duration is
			Power Clean	updated. The Power Clean option is activated automatically
				with this program. To deactivate, press the Power Clean
				button on the control panel.
	Pre Wash	cold	Delay	Crockery to be washed later.	—	4.0	0.03	14	NO
	Fragile	40°C	Delay	Light soiling, for example glasses and cups.	X	10.0	0.85	100	Light
	Rapid	45°C	Delay	Lightly soiled crockery, with no dried-on food.	X	11.0	0.80	30	NO
	Eco 2)	50°C	Delay
			Half Load	Normally soiled crockery. Energy-saving program.	X	11.0	0.93	240	Full
			Power Clean
	Fast Daily	60°C	Delay	Normally soiled crockery.	X	10.0	1.30	80	Full
	Silent	50°C	Delay	Normally soiled crockery, gentle and quiet thanks to the	X	13.0	1.20	290	Light
				lower spray pressure (39 dbA).
	Intensive	65°C	Delay	Recommended program for heavily soiled crockery,	X	14.0	1.60	145	Full
			Power Clean	especially suitable for pans and saucepans.
	Steam		Delay	Program including steam action dedicated for heavily soiled
				crockery, pots and pans. Soaking or hand pretreatment is no	X	14.0	1.70	180	Full
			Power Clean
				longer needed.
	Hygiene 3)		Delay	Normally or heavily soiled crockery, with additional
				antibacterial wash. Program interruption (e.g. due to door	X	13.0	1.50	118	Full
			Power Clean
				opening) can compromise elimination of germs.

1)Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2)Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “[e-mail]”.

3)The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

GB -2-

How to set water hardness in order to always assure the best cleaning results

First time use

10 4 1 9

3 2

5 6 7 8

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10spray arms

Water hardness should be set only before the first wash or if water hardness has been changed

Water hardness level is factory set for medium-hard water (level 4).

Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.

At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

-Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.

-The current water hardness setting will be visible on the display.

-Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the start button will set the level back to 1).

-Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

	1. Ask your water supply company what the water hardness is...						2. ...enter this value	Suggestions for detergent use
							on your dishwasher
	German		French		English	Water hardness	Insert value is shown	Gel or Powder	Tablets
	degrees °dH		degrees °fH		degrees °eH	level	in the display	(rinse aid and salt)
	0	- 5	0	- 9	0 - 6.3	Soft	1
	6 - 10		10	- 18	7 - 12.6	Medium	2
	11	- 15	19	- 27	13.3 - 18.9	Average	3	go to step 1
	16	- 21	28	- 37	19.6 - 25.9	Medium-hard	4	(see “Daily	if water is
								check”)	HARD extra salt
	22	- 28	38	- 50	26.6 - 35	Hard	5
									needs to be
	29	- 35	51	- 63	35.7 - 44.1	Very hard	6		added
									(go to step 1,
	36	- 50	64	- 90	44.8 - 62.4	Extremely hard	7		“Daily check”)

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)			Daily check
1	Visual indicator		Screw on the cap.
	(depending		Salt residual
	on the model).		around the cap
	Unscrew cap.		need to be
			removed. Some
			salt reservoir have
			a level indicator
			integrated in the
			cap (see below
	Fill the salt reservoir with water	Add salt (never add detergent!)	how to check).
	before the first wash only.	min. 0.8 kg/max. 1 kg

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

The salt level indicator lamp may remain lit at the end of several wash cycles. If the water hardness level falls within category (soft), no salt is required.

(depending on the model)

Salt indicator on the control panel

The indicator lamp lights up when SALT

NEEDS TO BE ADDED.

Salt indicator on the salt reservoir cap

	green: OK.	clear: NEEDS TO
		BE ADDED

GB -3-

Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

Daily check

2	Visual
	indicator

If required, open the cover B (press the dedicated button).

(depending on the model)

Add rinse aid to the max. line ~150 ml

The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.

Check the rinse aid indicator to check the	Rinse aid indicator on the control panel	Rinse aid indicator on the dispenser
level into the dispenser.	The indicator lamp lights up when	dark: OK.	clear: NEEDS TO BE ADDED
	RINSE AID NEEDS TO BE ADDED.

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations	Daily use

		Open the cover A
3	(press the dedicated button).

Insert detergent: Tablet / powder / liquid into the big chamber. Please look for the recommendation of the detergent manufacturer

Only fill the detergent dispenser prior to starting a wash program.

on the packaging of the detergent product.

Use only one tablet per one cycle, only placed in detergent dispenser.

All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory.

Some types of tablets may not dissolve completely during the short cycles (Rapid, Fragile, Handwash); placing the tablet on the tub bottom can help dissolving and washing.

Shut the cover

by pressing dedicated ribs.

GB -4-