ADP 720 WH
EN -1-
Chart
TAB LE T
SETTING
This setting allows
to optimize the
cycle
performances
according the type
of detergent used.
Push the Tablet
button (the
indicator lights up)
if you are using the
combined
detergents in
tablet.
If you are using
powder or gel
detergent, the
Tablet indicator
on the control
panel has to be off.
DELAYED START
BUTTON
Push the button (repeatedly)
to delay the start of the
program. Adjustable from
0:30 to 24 hours. With each
press of the button, the
delay start increases by: 0:30
if selection below 4 hours,
1:00 if selection is below
12 hours, 4 hours if selection
is above 12 hours. If 24
hours reached, and the
button is pressed, the
delayed start is deactivated -
"OFF" message is shown.
Then press the START
button. The delay time can
be adjusted after Start key
press. The dishwasher will
start after the set time.
START/PAUSE/
RESUME
BUTTON
Push this button to
start the selected
program: the
indicator lights up
and goes off at the
end of the program.
Press Start button or
open the door
during washing cycle
to pause the cycle -
the Start Indicator
blinks.
To resume the cycle
push Start button
and close the door.
CANCEL/OFF
BUTTON
Push this button to
switch off the control
panel.
If pressed for 3 seconds
when a program is
running it cancels this
program. If pressed
for 3 seconds when
the dishwasher is off,
it drains the water out.
If pressed during
program and delayed
start selection it
cancels the selection
and returns to
previous cycle and
option selection.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
5019 300 02470
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
ECO PROGRAM
INDICATOR
When lit, it indicates that
standard program is active.
MULTIZONE
INDICATOR
When lit, it indicates the
wash in the upper or lower
rack only.
KEYBOARD LOCK
INDICATOR
When lit, it indicates that
keyboard lock is active.
WATER TAP C LOSE D
- Alarm
Blinks when there is no inlet
water or water tap is closed.
WASH TIME DISPLAY
Indicates the cycle duration and the remaining time (h:min). With “Delayed start”
selected it indicates the time remaining until program start: “h24” if above
10 hours delay time remain and “h:mm” if below 10 hours delay time remain.
If “Fx Ey” messages appears on the display, see page 8 - chapter “What to do if...”.
DELAY INDICATOR
When lit, it indicates that de lay
is active.
RINSE AID
INDICATOR
When lit (at the end of the
cycle), the rinse aid dispenser
needs to be refilled.
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir needs
to be refilled.
PROGRAM
SELECTION
BUTTON
Push “P” button
(repeatedly) until
selected
program number
is shown on the
display (P1...Px) -
see “Table of
programs” - next
page.
After 3 seconds
the cycle
remaining time is
displayed.
POWERCLEAN
®
Thanks to the additional power
jets this option provides a more
intensive and powerful wash in the
lower rack, in the specific area.
MULTIZONE
Allows you to choose
the washing zones.
The appliance washes
both racks by default
(indicators are not lit).
To wash only in
specific rack, press
this button
repeatedly:
KEYBOARD
LOCK
This option allows you
to lock the buttons on
the control panel.
Children will not be
able to accidentally
start the dishwasher
by pressing the
buttons on the control
panel when this
option is selected.
If you want to activate
this option hold down
the button for
3 seconds.
Repeat the same
operation to unlock
the panel.
only upper rack
indicator lit
only lower rack
indicator lit
ANTIBACTERIAL
RINSE
This function activates an
antibacterial rinse at the end of the
wash cycle, guaranteeing a further
reduction of bacteria.
Press the button to activate or
deactivate the function.
This function can be used with the
programs indicated in the table of
programs.
The dishwasher door must be
kept shut for the entire duration of
the program in order to guarantee
reduction of bacteria.
If the door is opened the indicator
lamp starts flashing.
Quick reference guide
Whirlpool is a registered trademark of Whirlpool USA
EN -2-
Chart
1) Program data obtained under normal conditions and with default options on. Data may vary depending on ambient conditions and used options. Differences of up to 20 minutes are possible with sensor programs as
a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following
address: “contact@whirlpool.com”.
Power consumption in: Left-on mode: 1.08 W / Off-mode: 0.40 W.
Table of programs
Deter-
gent
Consumption
Drying
Phase
Programs
Available
options
Loading instructions Litres kWh
Minutes
1)
P1
6th Sense
®
PowerClean
®
40-70°C
Delay
Multizone
PowerClean
®
Antibacterial
Rinse
Use for normal soiled dishes with dried-on food.
Senses the level of soiling on the dishes and adjusts the
program accordingly. When the sensor is detecting the soil
level an animation appears in the display and the cycle
duration is updated. The PowerClean
®
option is activated
automatically with this program. To deactivate, press the
PowerClean
®
button on the control panel.
X 7.5-13 0.95-1.45 85-175 Full
P2
Pre-Wash cold
Delay
Multizone
Crockery to be washed later. — 4.0 0.01 14-16 NO
P3
Fragile 40°C
Delay
Multizone
Lightly soiled crockery, for example glasses and cups. X 10.5 0.85 105-114 Light
P4
Rapid 45°C
Delay
Multizone
Lightly soiled crockery, with no dried-on food. X 11.0 0.85 30-50 NO
P5
Eco
2)
50°C
Delay
Multizone
PowerClean
®
Antibacterial
Rinse
Normally soiled crockery.
Standard program the most efficient in terms of its
combined energy and water consumption.
X 10.0 0.92 230 Full
P6
Daily 60°C
Delay
Multizone
Antibacterial
Rinse
Normally soiled crockery. X 11.0 1.30 80-95 Full
P7
Silent 50°C
Delay
Multizone
Normally soiled crockery, gentle and quiet thanks to the
lower spray pressure.
X 14.0 1.20 290-299 Light
P8
Steam
Delay
Multizone
PowerClean
®
Antibacterial
Rinse
Program including steam action dedicated for heavily
soiled crockery, pots and pans. Soaking or hand
pretreatment is no longer needed.
X 14.5 1.75 180-190 Full
Quick reference guide
EN -3-
First time use
5
7
86
1
4
10
9
23
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set
before the first wash or if water
hardness has been changed
1
Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness is set to level 1 (soft), no
salt is required and salt indicator lamp will
remain off.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when
SALT NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft 1”!)
Screw on the cap.
Salt residual
around the cap
needs to be
removed. Some
salt reservoirs
have a level
indicator
integrated in the
cap (see below
how to check).
- Press and hold together Program and buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
- Press the Program button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the
start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/
Pause
button to save setting.
1. Ask your water supply company what the water hardness is... 2. ...enter this value
on your dishwasher
Salt required
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
Insert value is shown
in the display
0 - 5 0 - 9 0 - 6.3 Soft 1 NO
6 - 10 10 - 18 7 - 12.6 Medium 2
YES
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Ver y hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Add salt (never add detergent!)
min. 0.8 kg/max. 1 kg
Water hardness level is
factory set for medium-hard
water (level 4).
Detergents
When powder or gel
detergent is used,
regeneration salt must be
added and water hardness
level must be set as indicated
in the table on the right.
Also, when tablets which
include salt functionality are
used, regeneration salt still
must be added.
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).
Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
How to set water hardness in order to always assure the best cleaning results
Before first use, run the appliance with detergent and without loading.
EN -4-
Daily check
3
Daily use
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
(press the dedicated button).
Only fill the detergent
dispenser prior to
starting a wash
program.
Shut the cover
by pressing dedicated ribs.
If required,
open the
cover B
(press the
dedicated
button).
Add rinse aid
to the max.
line ~150 ml
The rinse aid dosage can be
adjusted to the detergent
used. The lower the setting,
the less rinse aid is dispensed
(factory setting: position 4).
Press the button to open the
cover B. Using a coin or
similar object, turn the arrow
to the desired setting. After
adjusting the rinse aid setting,
shut the cover again.
Visual
indicator
2
Check the rinse aid indicator to check the
level into the dispenser.
(depending on the model)
Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when
RINSE AID NEEDS TO BE ADDED.
dark: OK. clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause
a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6).
Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
Use only one tablet per one cycle, only
placed in detergent dispenser.
Some types of tablets may not dissolve
completely during the short cycles
(Fragile, Rapid, Handwash); placing the
tablet on the tub bottom can help
dissolving and washing.
Insert detergent: Tablet / powder / gel into the big chamber.
Please look for the recommendation of the detergent manufacturer
on the packaging of the detergent product.
Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Loading...