Whirlpool ADP 2550 WH INSTRUCTION FOR USE

GB ADP 2550	Quick Reference Guide

Further indications are given in the pages to follow and in the user instructions.

Programme selector

Options

Programme progress indicator

Rinse aid level indicator

Pre-rinse / Pre-wash

Add rinse aid.

Start button

Salt level indicator

Washing

Add regeneration salt; only add regeneration

Indicator lamp lit while the dishwasher is operating.

salt immediately before starting a wash

Flashes when a fault occurs.

Drying

programme.

Switches off at the end of the programme.

Programme end

Place the detergent in the:

Consumption

1)

small

large

Normal load

Programme Symbol

Programme selection and

compartment

compartment

and Temperature

recommended load type

Water

Energy

Time

(Litres)

(kWh)

(Min.)

Pre-wash

Crockery to be washed later.

-

-

5.0

0.02

9

Rapid 40° C

Lightly soiled crockery with no dried-on food.

-

X

13.0

0.85

30

Bio-Eco 50° C

2)

Normally or heavily soiled crockery with dried-on food.

X

X

16.0

1.26

133

Normal 65° C

3)

Normally soiled crockery.

X

X

16.0

1.60

86

Intensive 70° C

Heavily soiled pans and saucepans.

X

X

21.5

1.70

93

1)Values may vary in relation to usage, e.g.: different loads, water

temperatures - above or below 15° C - as well as water hardness and power supply voltage, etc.

2)Programme recommended when using detergents of type B (enzyme-based detergents). Reference programme for energy label.

3)Programme recommended when using detergents of type A (non enzyme-based detergents).

5019 100 91302

(We reserve the right to make technical modifications)

How to use the dishwasher

Upper and lower rack

1.After loading the dishwasher, close the door properly and open the water supply tap.

2.The dishwasher switches on automatically as soon as the programme selector knob is turned.

One of the programme indicator lamps will switch on.

3.Turn the selector knob to select the desired programme. The corresponding indicator lamp lights up. If required, select options (if supplied).

4.Press the Start button to start the selected programme. The Start indicator lamp will light up. Once set, the programmed data cannot be altered by turning the programme selector knob. Note: once the Start button has been pressed, the dishwasher memorises the last programme selected. This information remains in the memory even during interruption of the power supply.

To change the selected

programme, press the Start button for about 5 seconds, until the Start indicator lamp switches off.

Select a new programme and press the Start button.

Note: if the dishwasher is switched off during a wash programme, when switched on again it will resume the wash cycle from where it was interrupted.

Only open the dishwasher door if strictly necessary during a wash cycle and exercise maximum caution. Danger of scalding from steam.

5.To indicate the end of the programme, the Start indicator lamp switches off and the End indicator lamp (if fitted) lights up (for about 30 min.).

6.Once the Start indicator lamp has switched off, turn the programme selector knob to the initial position to switch off the dishwasher. All the indicator lamps switch off.

7.Open the door (warning: beware of hot steam). Unload the lower rack before the upper one. Close the water tap.

Upper rack

Rack height adjustment:

(The dishwasher is delivered with the upper rack in the top position).

The rack height can also be changed when loaded.

•To lower: pull out the two side handles and gently lower the rack.

•To raise: pull up the two side handles until the rack clicks into place.

•The rack must be level on both sides.

Crockery holders:

•Down: cups and long-stemmed glasses.

•Up: plates.

Glass holder:

Lower rack

A

A

C

Plate holders:

•(A) May be lowered to increase available space.

A

Cutlery basket:

•The cutlery basket can be removed to increase (C) available space.

•Some models are provided with a grid (D) that can be fitted onto the cutlery basket.

D

C

Please read the user instructions carefully.