Whirlpool 3LWED5500Y, 3LWGD4800Y, 3LWED4800Y, 3LWED4900Y, 3LMEDC100Y Installation Instructions

...

ELECTRIC OR GAS DRYER

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION DU SECHE-LINGE

ELECTRIQUE OU A GAZ

SECADORA A GAS O ELÉCTRICA

INSTRUCCIONES DE INSTALACIÓN

Table of Contents

DRYER SAFETY .........................................................................2

DRYER DISPOSAL ..................................................................... 5

INSTALLATION REQUIREMENTS .............................................5

Tools and Parts ......................................................................5

LOCATION REQUIREMENTS .................................................... 6

ELECTRICAL REQUIREMENTS ................................................ 7

GAS REQUIREMENTS ............................................................... 8

INSTALL LEVELING LEGS ......................................................... 9

Table des matiéres

SECURITE DU SECHE-LINGE ................................................ 19

ELIMINATION DU SECHE-LINGE ........................................... 22

EXIGENCES D’INSTALLATION ............................................... 22

Outillage et Pièces ............................................................... 22

EXIGENCES D’EMPLACEMENT ............................................. 23

SPECIFICATIONS ELECTRIQUES .......................................... 25

EXIGENCES CONCERNANT L’ALIMENTATION EN GAZ ...... 26

INSTALLATION DES PIEDS DE NIVELLEMENT .................... 26

EXIGENCES CONCERNANT L’EVACUATION ........................ 27

VENTING REQUIREMENTS ...................................................... 9

PLAN VENT SYSTEM ............................................................... 10

INSTALL VENT SYSTEM ......................................................... 12

CONNECT VENT ...................................................................... 12

LEVEL DRYER .......................................................................... 13

COMPLETE INSTALLATION CHECKLIST ..............................13

REVERSE DOOR SWING (OPTIONAL) ................................... 14

TECHNICAL SPECIFICATIONS ............................................... 18

TROUBLESHOOTING .............................................................. 18

PLANIFICATION DU SYSTEME D’EVACUATION ................... 28

INSTALLATION DU CONDUIT D’EVACUATION ..................... 30

RACCORDEMENT DU CONDUIT D’EVACUATION ...............30

REGLAGE DE L’APLOMB DU SECHE-LINGE ........................ 31

ACHEVER L’INSTALLATION LISTE DE VERIFICATION .........31

INVERSION DU SENS DE L’OUVERTURE DE LA PORTE

(FACULTATIF) ........................................................................... 32

CARACTERISTIQUES TECHNIQUES ..................................... 36

DEPANNAGE ............................................................................36

Índice

SEGURIDAD DE LA SECADORA ............................................ 37

ELIMINACIÓN DE LA SECADORA ......................................... 40

REQUISITOS DE INSTALACIÓN ............................................. 40

Piezas y herramientas: ........................................................ 40

REQUISITOS DE UBICACIÓN ................................................. 41

REQUISITOS ELÉCTRICOS .................................................... 42

REQUISITOS DEL SUMINISTRO DE GAS .............................. 43

INSTALACIÓN DE LAS PATAS NIVELADORAS...................... 44

REQUISITOS DE VENTILACIÓN ............................................. 45

W10454272C

PLANIFICACIÓN DEL SISTEMA DE VENTILACIÓN .............. 46

INSTALACIÓN DEL SISTEMA DE VENTILACIÓN .................. 47

CONEXIÓN DEL DUCTO DE ESCAPE....................................48

NIVELACIÓN DE LA SECADORA............................................48

LISTA DE CONTROL DE LA INSTALACIÓN TERMINADA .... 49

CAMBIO DEL SENTIDO DE ABERTURA DE LA PUERTA

(OPCIONAL) ............................................................................. 49

ESPECIFICACIONES TÉCNICAS ............................................ 54

SOLUCIÓN DE PROBLEMAS .................................................. 54

3LWED5500Y 3LWGD4800Y 3LWED4800Y 3LWED4900Y 3LMEDC100Y 3LMEDC300Y

DRYER SAFETY

FOR YOUR SAFETY

1. Do not use or store petrol or other ammable materials in this appliance or near this appliance.

2. Do not spray aerosols in the vicinity of this appliance while it is in operation.

3. Do not modify this appliance.

WARNING:

precautions, including the following:

To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using the dryer. Keep a minimum clearance of 100 mm (4 in.) between the

rear of the dryer and any wall. The operation of this appliance may affect the operation of

other types of appliances which take their air supply for safe combustion from the same room. There has to be adequate ventilation to replace exhausted air and thus avoid the back-ow of gases into the room from appliances burning other fuels, including open res, when operating the tumble dryer. If in doubt, consult the appliance manufacturers.

Do not obstruct the air supply to the dryer (see Installation Instructions for minimum clearances).

Do not place items exposed to cooking oils in your dryer. Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch re. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a re hazard.

If it is unavoidable to dry in the dryer items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers, or that have been contaminated by hair care products, should be washed in hot water with an extra amount of detergent before being dried in the dryer. These items may give off vapours that could ignite or explode. Such washing will reduce, but not eliminate, the hazard.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance by persons responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

The dryer should not be used if industrial chemicals have been used for cleaning.

Before the dryer is removed from service or discarded, remove the doors to the drying compartment.

Do not reach into the dryer if the drum is moving. A door switch is tted for your safety.

Do not install or store the dryer where it will be exposed to the weather.

Do not tamper with controls. Do not continue to use this appliance if it appears to be

faulty.

Do not repair or replace any part of the dryer or attempt any maintenance unless specically recommended in this Use and Care Guide. Repairs and servicing should only be carried out by competent service personnel.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product. Follow their instructions.

Clean dryer lint screen before or after each load. Do not operate dryer without lint screen in place.

Keep area around the exhaust and inlet openings and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

The interior of the dryer and exhaust vent should be cleaned periodically by qualied service personnel.

See Installation Instructions for earthing instructions. Do not dry unwashed items in this dryer.

The nal part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures the items will not be damaged.

Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows tted with foam rubber pads must only be dried on a clothesline.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualied person in order to avoid a hazard.

WARNING: Never stop a tumble dryer cycle before the

end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

SAVE THESE INSTRUCTIONS

DRYER DISPOSAL

INSTALLATION REQUIREMENTS

Tools and Parts:

Gather required tools and parts before starting installation.

Flat-blade screwdriver Wire stripper

6,2 mm (1/4") nut driver

Utility knife

#2 Phillips screwdriver

Adjustable wrench that opens to 25mm (1") or hex-head socket wrench (for adjusting dryer feet)

Tape measure

(direct wire installations)

Putty knife

Caulking gun and compound (for installing new exhaust vent)

Tools needed for Gas installations:

Tin snips (new vent installations)

Level

Pliers Vent clamps

204 mm (8") or 254 mm (10") pipe wrench

Pipe joint compound resistant to LP gas

Parts supplied:

Leveling legs (4)

Parts package is located in dryer drum. Check that all parts are included.

Square washers (3) * Included with models without preinstalled power cords

Parts needed: (not supplied with dryer)

■ Electric cord and plug; model specic - check to see if your

model comes with a pre-installed power cord.

■ Vent clamps

■ Vent elbows and ductwork

For gas installation:

Check local codes and gas supplier, and read electrical, gas, and venting requirements before purchasing parts.

Gas supply line must have:

■ Shutoff valve

Rigid gas supply line must be:

■ Minimum 12.5 mm (1/2") ID pipe

Flexible gas supply line must be:

■ Minimum 10 mm (3/8") ID approved exible hose

LOCATION REQUIREMENTS

Select proper location for your dryer to improve performance and minimize noise. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

You will need:

■ A location that allows for proper exhaust installation. The

dryer must be exhausted to the outdoors. See “Venting Requirements.”

■ An earthed electrical outlet located within 610 mm (2 ft) of

either side of the dryer. See “Electrical Requirements.”

■ A oor that will support the dryer and a total weight (dryer

and load) of 90,7 kg (200 lbs). The combined weight of a companion appliance should also be considered.

■ A level oor with maximum slope of 25 mm (1") under entire

dryer. If slope is greater than 25 mm (1"), install Extended Dryer Feet Kit, Part No. 279810. Clothes may not tumble properly and models with automatic sensor cycles may not operate correctly if dryer is not level.

■ It is important to make sure the room has an adequate air

supply for drying operation. The operation of this appliance may affect the operation of other appliances which take their air supply for safe combustion from the same room.

■ Adequate ventilation must be provided to avoid a backow

of gases into the room from appliances burning other fuels, including open res. If in doubt consult the appliance manufacturers.

IMPORTANT: The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Do not operate your dryer at temperatures below 7°C (45°F). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

L.P. Gas Conversion:

Gas conversion kit, part number 279918, available for purchase from your dealer. Full instructions are supplied with the kit. Conversion must be made by a competent technician.

Additional parts may be required, depending on your installation. Check local codes. Check existing venting and electrical and gas supply. Read “Electrical Requirements,” "Gas Requirements," and “Venting Requirements” before purchasing parts.

Proper installation is your responsibility.

Installation clearances:

For each arrangement, consider allowing more space for ease of installation and servicing; spacing for companion appliances and clearances for walls, doors, and oor moldings. Space must be large enough to allow door to fully open. Add spacing on all sides of dryer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

Dryer Dimensions

279 mm

Front View:

1095 mm

(43

Side View:

356 mm

(14")

Back View:

686 mm

(27")

578 mm

(22

743 mm

(29

260 mm

(10

/ 4

(11")

Recessed Area and Closet Installation

This dryer may be installed in a recessed area or closet. If a closet door or louvered door is installed, the minimum unobstructed air openings in the top and bottom of the door

98 mm

489 mm

(19

108 mm

/ 4

are required. For recessed area and closet installations, minimum clearances can be found on the serial tag on the dryer.

356 mm

(14") max.

76 mm

(3")

310 mm

(3")

(48" )

155 mm

(24" )

102 mm

(4")

25 mm

(1")

457 mm

(18")

25 mm

(1")

76 mm

■ Dimensions shown are minimum spacings required. Consider

allowing more space for ease of installation, servicing, and compliance with local codes and ordinances.

■ Additional spacing for companion appliances and clearances

for walls, doors, and oor moldings should also be considered. Add spacing of 25 mm (1") on all sides of dryer to reduce noise transfer.

■ This dryer must not be installed behind a lockable door,

a sliding door or a door with a hinge on the opposite side to that of the dryer.

■ The dryer must be exhausted outdoors.

■ No other fuel-burning appliance may be installed in the same

closet as the dryer.

972 mm

(38

Side View of Side Swing Door:

578 mm

(22

359 mm

(14

743 mm

(29

260 mm

(10

ELECTRICAL REQUIREMENTS

IMPORTANT: Observe all governing codes and ordinances. If the model comes with a pre-installed power cord, do not

modify or replace.

100 mm

(4")

108 mm

Some models are supplied without an electric cord and plug. It must be connected by a qualied electrician to a single-phase electricity supply at the voltage shown on the dataplate, using a suitable xed wiring installation in accordance with local and national wiring regulations.

■

A 3-wire circular cord of minimum conductor size of 4 mm2

cross-section area should be used.

■

A 30A supply fuse should be used, and a switch with a

minimum contact separation of 3 mm in both poles must be incorporated into the xed wiring for dryer disconnection. The dryer should be positioned so that the disconnection switch is easily accessible to the user.

■

A cord clamp bushing is provided on the dryer, and should

be tightened on completion of wiring. The electrical mains terminals are located behind the small rear access panel (terminal block cover), and connections should be made in accordance with the terminal markings. Remember to replace the terminal access panel (terminal block cover).

■

If using an unterminated power cord,

the square washers that are provided must be used.

NOTE: In accordance with the European EMC Directive

(89/336/EEC) the maximum electricity supply system impedance to which the electric dryer should be connected is declared to be

0.29 Ohm + J0.18 Ohm. This dryer has a Maximum power absorption/usage of 4700 watts.

GAS REQUIREMENTS

If code permits and an additional earth bond wire is used, it is recommended that certied electrician determine that the earth bond path is adequate.

Electrical Safety Standards: The manufacturer has chosen compliance with IEC/EN.60335 standards as the most appropriate for this product.

Do not use an adapter.

Recommended Earthing Method

■ It is your responsibility to contact a qualied electrical installer

to ensure that the electrical installation is adequate and in conformance with all local codes and ordinances.

OBSERVE ALL GOVERNING CODES AND ORDINANCES. Gas supply:

Check that dryer is equipped with the correct burner for the particular type of gas supply. Burner information will be found on the model/serial rating plate in the door well of the dryer. If this information does not agree with the type of gas available, see your dealer.

Natural Gas:

This dryer is factory adjusted for use with NATURAL GAS (G20), and no further adjustment should be required at installation.

L.P. Gas:

This dryer is also certied for use with L.P. (propane or butane) gases with appropriate conversion. No attempt shall be made to convert the appliance from the gas specied on the model/serial rating plate for use with a different gas without consulting the serving gas supplier.

Conversion must be done by a qualied service technician. Gas conversion kits are available for purchase from your dealer.

Full instructions are supplied with the kit.

Supply Line Requirements

Provide a rigid gas supply line to the dryer location. It should be minimum 12.5 mm (1/2") ID. When acceptable to the gas supplier and local codes, 10 mm (3/8") ID rigid supply line may be used for lengths under 6.1 m (20'). Pipe-joint compounds resistant to the action of L.P. gas must be used.

Gas connection to the dryer itself should be made by means of a exible gas hose suitable for the appliance and gas category in accordance with national installation regulations. If in doubt, contact the gas supplier. It should be minimum 10 mm (3/8") ID.

A means of restraint should be used between the appliance and the wall to prevent straining of the rigid gas supply when the appliance is moved. An appropriate length of chain and a wall hook is recommended.

The dryer gas inlet connection is a 10 mm (3/8") NPT thread. An adapter is supplied for conversion to standard ISO.228-1 thread 10 mm (3/8" BSP).

Check for leaks by using an approved noncorrosive leak detection solution. Bubbles will show a leak. Correct any leak found. A pressure measurement tapping is provided on the gas valve within the dryer, accessible after removal of the lower front panel.

Gas supply pressure testing

The dryer must be disconnected from the gas supply piping system during any pressure testing of that system.

Screw in leveling legs

diamond marking

Examine leveling legs, nd diamond marking. Screw legs into leg holes by hand, use a wrench to nish turning legs until diamond marking is no longer visible.

Now stand the dryer on its feet. Slide the dryer until it is close to its nal location. Leave enough room for electrical connection and to connect the exhaust vent.

INSTALL LEVELING LEGS

Prepare dryer for leveling legs

To avoid damaging oor, use a large at piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard.

VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

WARNING: Gas dryers should only be installed in a room

if the room meets the appropriate ventilation requirements specied in the national installation regulations. Make sure the room containing the dryer has an adequate air supply for gas combustion and drying operation. A window or equivalent means of ventilation must be opened in the room when the dryer is in use (an equivalent form of opening includes an adjustable louver, hinged panel, or other means of ventilation that opens directly to outside air.

WARNING: The design of the ue system should ensure that

any condensate formed when operating the appliance is either retained or subsequently evaporated or discharged. Following these installation instructions should adequately meet this requirement.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or exible metal vent shall be used for exhausting.

102 mm

(

)

■ Only a 102 mm (4") heavy metal exhaust vent and clamps

may be used. Do not install metal vent that is smaller than 102 mm (4") in diameter.

■ Do not use plastic, non-metal, or metal foil vent

Rigid metal vent

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess exible metal vent to avoid sagging

and kinking that may result in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 2.4 m (7

/4 ft.).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged with lint. Replace plastic or metal foil vents with rigid metal or exible metal vents. Review "Vent System Chart" and if necessary, modify existing vent system to achieve best drying performance.

Elbows:

■ 45° elbows provide better airow than 90° elbows.

Good Better

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape.

Exhaust hoods:

Recommended Styles:

Louvered Hood

Box Hood

Acceptable Style:

Angled Hood

■ An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

■ Exhaust hood must be at least 305 mm (12") from the ground

or any object that may be in the path of the exhaust (such as owers, rocks, bushes, or snow line, etc.).

■ Do not use an exhaust hood with a magnetic latch.

Vent products can be purchased from your dealer. For more information, see “Assistance or Service” section in your “Use and Care Guide.”

PLAN VENT SYSTEM

The design of the ue system should ensure that any condensate formed when operating the appliance from cold, is either retained and subsequently evaporated or discharged. Following these installation instructions should adequately meet this requirement.

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

A. Dryer B. Elbow C. Wall D. Exhaust hood

E. Clamps F. Rigid metal or exible metal vent G. Vent length necessary to connect elbows H. Exhaust outlet

Optional exhaust installations (on some models)

This dryer can be converted to exhaust out the right side, left side, or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted.

Periscope installation

Determine vent path:

■ Select route that will provide straightest and most direct

path outdoors.

■ Plan installation to use fewest number of elbows and turns.

See “Venting Requirements.”

■ When using elbows or making turns, allow as much room

as possible.

■ Bend vent gradually to avoid kinking.

■ Use as few 90° turns as possible.

A. Standard rear offset exhaust installation B. Left or right side exhaust installation C. Bottom exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions.

Over-The-Top installation (also available with one offset elbow)

Determine vent length and elbows needed for best drying performance:

■ Use following Vent System Chart to determine type of vent

material and hood combinations acceptable to use. NOTE: Do not use vent runs longer than those specied

in Vent System Chart. Exhaust systems longer than those specied will:

■ Shorten life of dryer.

■ Reduce performance, resulting in longer drying times

and increased energy usage.

305 mm (

12" mín.

)

305 mm

(

12" mín.

)

The Vent System Chart provides venting requirements that will help achieve best drying performance.

Vent System Chart

Connect vent to exhaust hood

Number of

90° turns or elbows

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add one 90° turn to the chart.

The maximum length using a 51 mm x 152 mm (2"x 6")

rectangular vent with 2 elbows and a 64 mm (2-1/2") exhaust hood is 2,4 m (8ft).

For exhaust systems not covered by the Vent System Chart (such

as multiple unit hookups, plenums, and power-assist fans), see Service Manual, Part 603197. (To purchase the Service Manual, contact your local authorized service dealer.

Type

of vent

Rigid metal

Box/louvered

hoods

15,8 m (52 ft.)

13,4 m (44 ft.)

11,0 m (36 ft.)

8,2 m (27 ft.)

6,1 m (20 ft.)

Angled

hoods

13,4 m (44 ft.)

11,0 m (36 ft.)

18,5 m (28 ft.)

6,4 m (21 ft.)

4,3 m (14 ft.

Vent must t over the exhaust hood. Secure vent to exhaust hood with 102 mm (4") clamp. Run vent to dryer location using straightest path possible. Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into interior of vent to secure vent, because they can catch lint.

CONNECT VENT

1. Connect vent to exhaust outlet

INSTALL VENT SYSTEM

Install exhaust hood

Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood.

Using a 102 mm (4") clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must t over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 102 mm (4") clamp.

2. Move dryer to nal location

Move dryer to nal location. Avoid crushing or kinking vent. After dryer is in place, remove corner posts and cardboard from under the dryer.

LEVEL DRYER

1. Level Dryer

Check levelness of dryer from side to side. Repeat from

front to back.

NOTE: The dryer must be level to reduce noise and assure

proper performance.

If legs are not long enough to level dryer, order Extended Dryer

Feet kit, Part No. 279810 (sold two legs per kit), from your dealer.

Not Level LEVEL Not Level

1. Tighten and adjust leveling legs

COMPLETE INSTALLATION CHECKLIST

Check that all parts are now installed. If there is an extra

part, go back through steps to see what was skipped.

Check that dryer legs are properly installed.

Check that you have all of your tools.

Dispose of/recycle all packaging materials.

Check dryer’s nal location. Be sure vent is not crushed

or kinked.

Secure all exhaust vent joints with 102 mm (4")clamps.

For power supply cord installation, plug into an earthed outlet.

For direct wire installation, turn on power.

Check that dryer is level. See “Level Dryer”.

Remove lm on console and any tape remaining on dryer.

Wipe dryer drum interior thoroughly with a damp cloth

to remove any dust.

Read “Dryer Use” in your Use and Care Guide.

Set the dryer on a full heat cycle (not an air cycle) for

20 minutes and start the dryer. (If you have a gas dryer, it is equipped with an electronic ignition system for the burner which is fully automatic; no action is needed by the user (there is no pilot light).

If the dryer will not start, check the following:

■ Controls are set in a running or “On” position.

■ Start button has been pushed rmly.

■ Dryer is plugged into an outlet and/or electrical supply

is on.

■ Household fuse is intact and tight, or circuit breaker has

not tripped.

■ Dryer door is closed.

When the dryer has been running for 5 minutes, open the

dryer door and feel for heat. If you feel heat, cancel cycle and close the door.

If you do not feel heat, turn off dryer, and check the following:

■ There may be 2 household fuses or circuit breakers for

the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualied technician.

NOTE: You may notice an odor when the dryer is rst heated. This odor is common when the heating element is rst used. The odor will go away.

If dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once legs are level, make sure all four legs are snug against the ground.

REVERSE DOOR SWING (OPTIONAL)

If your door is the 29" Large Side-Swing Door, follow steps 1-6.

If your door is the 29" Super Wide Side-Swing Door, follow steps 1-13.

3. Lift door off top screws

Lift door until top screws in cabinet are in large part of hinge slot. Pull door forward off screws. Set door on top of dryer. Remove top screws from dryer cabinet.

NOTE: Magnetized screw driver is helpful.

Large Side-Swing Door

1. Place towel on dryer

Place towel on top of dryer to avoid damaging the surface.

2. Remove bottom screws

4. Remove and transfer hinge

hole plugs

Use a small, at-blade screwdriver to gently remove 4 hinge hole plugs on left side of dryer cabinet. Insert plugs into hinge holes on opposite side of dryer cabinet.

5. Insert screws in hinge holes on

dryer cabinet

Open dryer door. Remove bottom screws from dryer cabinet side of hinges. Loosen (do not remove) top screws from dryer cabinet side of hinges.

NOTE: Two people maybe needed to reinstall door.

Insert screws into bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges.

6. Check door strike alignment

3. Lift door off top screws

Close door and check that door strike aligns with door catch. If needed, slide door catch left or right within slot to adjust alignment.

Super Wide Side-Swing Door

1. Place towel on dryer

Place towel on top of dryer to avoid damaging the surface.

2. Remove bottom screws

Lift door until top screws in dryer cabinet are in large part of hinge slot. Pull door forward off screws. Set door (handle side up) on top of dryer. Remove top screws from dryer cabinet.

4. Remove screws from hinges

Remove screws attaching hinges to door.

5. Remove screws from door

Open dryer door. Remove bottom screws from dryer cabinet side of hinges. Loosen (do not remove) top screws from dryer cabinet side of hinges.

Remove screws at top, bottom, and side of door (4 screws). Keep door screws separate from hinge screws as they are different sizes. Holding door over towel on dryer, grasp sides of outer door and lift to separate it from inner door. NOTE: Do not pry apart with putty knife or screwdriver. Do not pull on door seal or plastic door catches.

6. Rotate outer door

Take outer door and rotate in 180º and set it back down on inner door. Be certain to keep cardboard spacer centered between doors. Reattach outer door panel to inner door panel so handle is on the side where hinges were just removed. Insert 4 door screws.

7. Flip door over

8. Attach door hinges

Flip door over so handle side is down.

Reattach door hinges to dryer door so that the larger hole is at the bottom of the hinge.

9. Remove door strike

Remove door strike from dryer cabinet and set aside.

10. Remove and transfer

hinge hole plugs

Use a small, at-blade screwdriver to gently remove 4 hinge hole plugs on left side of dryer cabinet. Transfer plugs into hinge holes on opposite side of dryer cabinet.

11. Insert screws in hinge holes on

dryer cabinet

12. Remove door strike plug

Remove door strike plug. Insert the door strike removed in Step 9 into hole and secure with screw. Insert door strike plug into original door strike hole and secure with screw.

13. Check door strike alignment

NOTE: Two people maybe needed to reinstall door.

Insert screws into the bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges.

Close door and check that door strike aligns with door catch. If it is needed, slide door catch left or right within slot to adjust alignment.

TECHNICAL SPECIFICATIONS

220-240V~50Hz 1ph 3A max. IPX4

Maximum Power Absortion/Usage: 4700 Watts Moisture Resistance (Water Ingress, Rain Test): 5500-5600

Factory set for NATURAL GAS: Injector: 2,2 mm Heat input gross: 5,9 kW

European Country:

European Gas Category: Gas Flow Rate: Supply Pressure (G20): Factory Adjusted Pressure:

With LP Gas Conversion Kit: Injector size: 1,25 mm Heat input gross: 6,4 kW

European Country:

European Gas Category: Butane Supply Pressure (G30):

Adjusted Pressure: Propane Supply Pressure (G31): Adjusted Pressure:

With France/Belgium NATURAL GAS conversion kit: Injector size: 1,65 mm Heat input gross: 5,9 kW

European Country: European Gas Category: Supply Pressure (G20):

Supply Pressure (G25): Adjusted Pressure:

Note: Conversion kit: From Natural Gas to LP Gas : Whirlpool Part No. W10233219.

Conversion kit: From Natural Gas to Natural Gas - France/Belgium: Whirlpool Part No. W10184947. Manufacturer: Whirlpool Corporation, Benton Harbor, Michigan 49022, USA.

CZ, CY, ES, GB, GR, HR, IE, IT,

PT, SI, SK, TR

2H3+

0.562703 M3/HR 20 mbar

7.4 mbar

PT, SI, SK, TR

2H3+

28-30 mbar

N/A

37 mbar

N/A

FR, BE

2E+

20 mbar 25 mbar

N/A

CY, CZ, DK, EE, FI, GR, HU, IT,

NO, RO, SE, SK, TR

2H3B/P

0.562703 M3/HR 20 mbar

7.4 mbar

CY, CZ, DK, EE, FI, GR, HU, IT,

NO, RO, SE, SK, TR

2H3B/P

30 mbar

N/A

30 mbar

N/A

These units are sold in multiple regions with different requirements for measuring capacity. Below are a few of the valid forms of measure posted on this product:

Dry Linen Capacity: A weight measure that reects a maximum

load size that can be loaded into the dryer.

IEC Capacity: The capacity measure that represents the maximum capacity of dry linens and textiles which the manufacturer declares can be treated in a specic cycle.

Dry Linen Capacity

TROUBLESHOOTING

See the “Use and Care Guide” to possibly avoid the cost of a service call.

10,5 kg (23 lb)

IEC Capacity

7,5 kg (16,5 lb)

SECURITE DU SECHE-LINGE

IMPORTANTES INSTRUCTIONS DE SECURITE

AVERTISSEMENT :

l’utilisation du sèche-linge, il convient d’observer certaines précautions fondamentales, notamment :

An de réduire le risque d’incendie, de choc électrique ou de blessures corporelles lors de

Lire toutes les instructions avant d’utiliser le sèche-linge. Laisser un dégagement minimal de 100 mm (4") entre l’arrière

du sèche-linge et les éventuelles parois environnantes.

Le fonctionnement de cet appareil peut affecter celui d’autres appareils dont la source d’approvisionnement en air se fait dans la même pièce pour une combustion sans danger. Lorsqu’on utilise le sèche-linge, une aération adéquate est nécessaire pour renouveler l’air rejeté et ainsi éviter le retour dans la pièce de gaz en provenance d’appareils ménagers utilisant d’autres carburants comme combustible, y compris les feux ouverts. En cas de doute, consulter le fabricant de l’appareil.

Ne pas obstruer l’alimentation en air du sèche-linge (voir les instructions d’installation pour les dégagements minimaux).

Ne pas placer d’articles tâchés d’huile de cuisson dans le sèche-linge. Des articles ayant été au contact d’huile peuvent s’enammer spontanément, surtout s’ils sont exposés à des sources de chaleur, telles un sèche-linge. Les articles peuvent chauffer, entraînant une réaction d’oxydation de l’huile. Le phénomène d’oxydation crée de la chaleur. Si la chaleur ne peut pas s’échapper, les articles peuvent devenir sufsamment chauds pour prendre feu. Le fait d’empiler, d’entasser ou d’entreposer des articles ayant été au contact d’huile peut empêcher la chaleur de s’échapper et créer un risque d’incendie.

Si l’on doit faire sécher dans le sèche-linge des articles ayant été souillés par des substances telles que de l’huile de cuisson, acétone, alcool, pétrole, kérosène, produit détachant, térébenthine, cire, décapant pour cire ou produits de coiffure, ils doivent être lavés à l’eau chaude avec un supplément de détergent avant d’être séchés dans le sèche-linge. Ces articles sont susceptibles de dégager des vapeurs qui pourraient s’enammer ou exploser. Les laver ainsi au préalable permet de réduire mais non de supprimer ce risque.

Cet appareil ne convient pas à une utilisation par des personnes (y compris des enfants) à capacités physiques, sensorielles ou mentales réduites, ou dépourvues d’expérience et de connaissances, à moins qu’elles ne soient placées sous supervision ou qu’elles aient reçu des instructions concernant l’utilisation de l’appareil par une personne responsable de leur sécurité.

Il convient de surveiller les enfants pour qu’ils ne jouent pas avec l’appareil.

Ne pas utiliser le sèche-linge si l’on a utilisé des produits chimiques industriels pour le nettoyage.

Retirer les portes du compartiment de séchage avant de retirer le sèche-linge pour un entretien ou de le mettre au rebut.

Ne pas accéder à l’intérieur du sèche-linge pendant le fonctionnement du tambour. Pour votre sécurité, l’appareil est pourvu d’un contacteur de porte.

Ne pas installer ou entreposer le sèche-linge dans un endroit où il serait exposé aux intempéries.

Ne pas effectuer d’intervention non autorisée sur les commandes.

Ne pas utiliser ce sèche-linge s’il semble défectueux.

Ne pas procéder à l’entretien, à la réparation ou au remplacement de n’importe quelle pièce du sèche-linge, à moins que ceci ne soit spéciquement recommandé dans le guide d’utilisation et d’entretien. Seul un dépanneur compétent est habilité à effectuer une intervention de réparation ou d’entretien sur cet appareil.

Ne pas utiliser d’assouplissants pour tissu ou de produits pour éliminer l’électricité statique à moins que cela ne soit recommandé par le fabricant d’assouplissants pour tissu ou du produit. Suivre leurs instructions.

Nettoyer le ltre à peluches du sèche-linge avant ou après chaque charge. Ne pas utiliser le sèche-linge si le ltre à peluches n’est pas installé.

La zone située autour des ouvertures de prise ou d’évacuation d’air et les zones adjacentes doivent être exemptes de peluches et poussières.

L’intérieur du sèche-linge et le conduit d’évacuation doivent être nettoyés régulièrement par un personnel d’entretien qualié.

Voir les instructions d’installation pour les instructions de mise à la terre.

Ne pas faire sécher d’articles non lavés dans ce sèche-linge.

La partie nale du programme de séchage par culbutage a lieu sans chaleur (programme de refroidissement) pour que les articles soient laissés à une température qui ne risque pas de les endommager.

Les articles tels que le caoutchouc mousse (mousse de latex), les bonnets de douche, les textiles imperméabilisés, les articles avec endos de caoutchouc et les vêtements ou oreillers rembourrés avec matelassage en mousse doivent être séchés uniquement sur une corde à linge.

Si le cordon d’alimentation est endommagé, il doit être remplacé par le fabricant, son agent de service ou toute autre personne qualiée an d’éviter tout danger.

AVERTISSEMENT : Ne jamais arrêter un sèche-linge

en phase de culbutage avant la n du programme de séchage à moins de retirer les articles rapidement et de les étendre an de dissiper la chaleur.

CONSERVER CES INSTRUCTIONS

ELIMINATION DU SECHE-LINGE

EXIGENCES D’INSTALLATION

Outillage et Pièces

Rassembler les outils et piéces nécessaires avant de commancer l’installation.

Tournevis à lame plate Pince à dénuder les ls

Tourne-écrou de 6,2 mm (1/4")

Couteau utilitaire

Tournevis Phillips no 2

Clé à molette avec ouverture

jusqu’à 25 mm (1") ou clé à douille hexagonale (pour ajuster les pieds du sèche-linge)

Mètre ruban

(pour les installations à raccordement direct)

Couteau à mastic

Pistolet à calfeutrage et composé de calfeutrage (pour l’installation d’un nouveau circuit d’évacuation)

Cisaille de ferblantier (pour l’installation d’un nouveau conduit)

Niveau

Pince

Brides de conduit

+ 50 hidden pages