Page 1
Model No. WLCCEX69571
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
Serial No.
Write the serial number in the space
above for future reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfaction through direct assistance from our factory.
USER'S MANUAL
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-936-4266
Mon.–Fri., 8h00–18h30 EST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
Page 2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE PURSUIT 795i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions before
using the exercise cycle.
Read all instructions in this manual before
1.
using the exercise cycle. Use the exercise
cycle only as described.
2. It is the responsibility of the owner to ensure
that all users of the exercise cycle are adequately informed of all precautions.
3. Use the exercise cycle indoors, away from
moisture and dust. Place the exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet from damage.
4. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
5. Keep children under the age of 12 and pets
away from the exercise cycle at all times.
6. The exercise cycle should not be used by
persons weighing more than 250 pounds
(115 kg).
7. Wear appropriate clothing when exercising; do
not wear loose clothing that could become
caught on the exercise cycle.
athletic shoes for foot protection.
8. When adjusting the seat, insert the seat knob
through one of the holes in the seat post
(see the drawing on page 4). Do not insert
the seat knob under the seat post.
9. Always keep your back straight when using
the exercise cycle. Do not arch your back.
10. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
11. The exercise cycle is intended for in-home
use only. Do not use the exercise cycle in a
commercial, rental, or institutional setting.
12. The pulse monitor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse monitor is intended only
as an exercise aid in determining heart rate
trends in general.
Always wear
WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read
all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
The decal shown at the right has been
placed on the exercise cycle. If the decal
is missing, or if it is not legible, please
call our Customer Service Department to
order a free replacement decal at1-888936-4266.
in the location shown.
Apply the replacement decal
3
Page 4
BEFORE YOU BEGIN
Thank you for selecting the new WESLO®PURSUIT
795i exercise cycle. The PURSUIT 795i blends
advanced engineering with contemporary styling to
provide you with a low-impact workout in the convenience and privacy of your own home.
For your benefit, read this manual carefully before
you use the PURSUIT 795i. If you have additional
questions, please call our Customer Service
Department toll-free at 1-888-936-4266, Monday
through Friday, 8:00 a.m. until 6:30 p.m. Eastern Time
Water Bottle Holder
(bottle is not included)
Book Rack
(excluding holidays). To help us assist you, please
mention the product model number and serial number
when calling. The model number is WLCCEX69571.
The serial number can be found on a decal attached
to the PURSUIT
ual for the location of the decal).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
795i (see the front cover of this man-
Handlebars
Console
Resistance Knob
Seat
Seat Post
Seat Knob
Pedal
BACK
FRONT
Front Wheels
RIGHT SIDE
4
Page 5
PART IDENTIFICATION CHART
M10 x 25mm Button Screw (8)–5
M10 Nylon Locknut (31)–4
M8 Nylon Locknut (21)–3
M4 x 16mm Screw (9)–5
M8 Split Washer (53)–3 M10 Split Washer (41)–5
M10 x 70mm Carriage Bolt (30)–4
Use the chart below for help identifying the small
parts used in assembly. The number in parenthesis
below each part refers to the key number of the part.
The second number refers to the quantity used in
assembly. Note: Some parts may have been pre-
attached for shipping purposes. If a part is not
found in the parts bag, check to see if it has been
pre-attached.
5
Page 6
ASSEMBLY
Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the
packing materials until assembly is completed.
Assembly requires the included allen wrench , a phillips screwdriver and two
adjustable wrenches .
1. Identify the Front Stabilizer (17), which has Wheels
(25) on the ends. Hold the Front Stabilizer against
the saddle on the front of the Frame (15). Make
sure that the Front Stabilizer is turned so the square
holes are facing away from the saddle. Attach the
Front Stabilizer with two M10 x 70mm Carriage
Bolts (30) and two M10 Nylon Locknuts (31).
Attach the Rear Stabilizer (not shown) to the rear of
the Frame (15) in the same manner.
2. The Console (7) requires two AA batteries (not
included). Alkaline batteries are recommended.
Refer to the inset drawing. Open the battery cover
on the underside of the Console as shown. Press
two batteries into the battery compartment. Make
sure that the negative ends of the batteries
(marked “–”) are touching the springs in the
battery compartment. Close the battery cover.
Insert the console wire through the Handlebar Post
(14). Connect the console wire to the Reed Switch
Wire (54). Attach the Console (7) to the Handlebar
Post with four M4 x 16mm Screws (9).
1
30
25
2
Console
Wire
17
7
25
15
7
12
31
Battery Cover
9
Batteries
Carefully slide the Handlebar Post (14) onto the
Frame (15). Be careful to avoid pinching the
wires inside the Handlebar Post. Attach the
Handlebar Post with three M10 x 25mm Button
Screws (8) and three M10 Split W
Attach the Knob Housing (12) to the Handlebar Post
with a M4 x 16mm Screw (9).
Attach the Handlebar (5) to the Handlebar Post (14)
3.
with two M10 x 25mm Button Screws (8) and two
M10 Split Washers (41).
ashers (41).
15
14
8
41
8
14
9
54
41
8
3
8
41
5
6
Page 7
4. Tighten the two Side Shield Screws (4) in the Left
Side Shield (1). Next, tighten the two Side Shield
Screws in the Right Side Shield (2).
4
40
Press the Side Shield Cover (40) onto the Left and
Right Side Shields (1, 2).
5. Insert the Seat Post (20) into the Frame (15). Align
one of the holes in the Seat Post with the hole in
the Frame. Insert the Seat Knob (29) into the Frame
and the Seat Post, and tighten the Seat Knob into
the Frame.
through one of the holes in the Seat Post; do
not insert the Seat Knob under the Seat Post.
Attach the Seat (19) to the Seat Post (20) with three
M8 Nylon Locknuts (21) and three M8 Split Washers
(53). (Note: The Nylon Locknuts and Split Washers
may be pre-attached to the bottom of the Seat.)
Make sure to insert the Seat Knob
2
1
4
5
19
53
53
21
21
Identify the Left Pedal (28); there is an “L” on the
6.
Left Pedal for identification. Using an adjustable
wrench, tighten the Left Pedal counterclockwise into
the left arm of the Crank (33).
Tighten the Right Pedal (not shown)
the right arm of the Crank (33).
7. Make sure that all parts are properly tightened
before you use the exercise cycle. Place a mat
under the exercise cycle to protect the floor or car
pet.
clockwise into
20
29
15
6
33
28
-
7
Page 8
HOW TO USE THE PURSUIT 795i
HOW TO ADJUST THE SEAT
fective
For ef
exercise, the
Seat (19) should
be at the proper
height. As you
pedal, there
should be a
slight bend in
your knees
when the pedals
are in the lowest
position. To
adjust the Seat,
first hold the
Seat and
unscrew the
Seat Knob (29).
Align one of the
holes in the
Seat Post (20) with the hole in the Frame (15). Insert
the Seat Knob into the Frame and the Seat Post, and
tighten the Seat Knob into the Frame. Caution: Make
sure to insert the Seat Knob through one of the
holes in the Seat Post; do not insert the Seat
Knob under the Seat Post.
19
20
29
15
HOW TO APPLY AN INFORMATION DECAL TO
THE CONSOLE
All of the infor
mation on the
console is printed
in English. The
included decal
sheet contains
the same information in five
other languages.
If English is not
your language,
find the decal on
the decal sheet
that is printed in
your language.
-
HOW TO ADJUST THE PEDALLING RESISTANCE
To vary the
intensity of your
exercise, the
pedalling resistance can be
adjusted. The
resistance is
controlled with
the Resistance
Knob (10). To
increase the
resistance, turn
the Resistance
Knob clockwise;
to decrease the
resistance, turn
the Resistance Knob counterclockwise.
10
Next, peel the
information decal
off the decal
sheet. Apply the
decal to the
console in the
location shown.
TTERY INSTALLATION
BA
Before the console can be operated, two AA
batteries must be installed. If you have not installed
batteries, see assembly step 2 on page 6.
8
Page 9
DIAGRAM OF THE CONSOLE
The console offers six modes that provide instant
exercise feedback. Each mode is displayed for five
seconds in a repeating cycle. The modes are
described below.
Pulse—This mode displays your heart rate
when the pulse sensor is used.
Calorie—This mode displays the approximate
number of calories you have burned.
Fat Calorie—This mode displays the approximate number of fat calories you have burned.
(See BURNING FAT on page 10.)
Speed—This mode displays your pedalling
speed, in kilometers per hour.
Time—This mode displays the length of time
you have exercised.
Distance—This mode displays the total number
of kilometers you have pedalled during your
workout.
HOW T
1.
O OPERA
o turn on the
T
, press the
power
on/reset button
or simply begin
pedalling. When
the power is
turned on, the
entire display
will appear for two seconds. The console will then
be ready for operation.
TE THE CONSOLE
2. When the power
is turned on, the
console will
begin displaying
all modes in a
repeating cycle
(except for the
pulse mode).
Flashing arrows will show which mode is currently
displayed.
3. To measure your
pulse, stop pedalling and place
your thumb on
the pulse sensor
as shown. The
pulse sensor is
pressure-activated—fully press down the pulse sensor.
press too hard, or the circulation in your thumb
will be restricted, and your pulse will not be
detected. Next, slightly raise your thumb until the
heart-shaped indicator in the display flashes
steadily. Hold your thumb at this level. After 5 to 10
seconds, three dashes will appear in the display
and your pulse will then be shown. Hold your thumb
on the sensor for another 15 seconds for the most
accurate reading. If the displayed pulse appears to
be too high or too low, or if your pulse is not displayed, lift your thumb off the sensor and allow the
display to reset. Press down again on the sensor as
described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of pressure to the pulse sensor. Try the sensor several
times until you become familiar with it.
o reset the dis
T
4.
, press the
play
on/reset button.
5. To turn off the power, simply wait for about six
minutes. Note: The console has an “auto-off”
feature. If the pedals are not moved and the con
sole buttons are not pressed for six minutes, the
power will turn off automatically in order to conserve the batteries.
-
Arrow
Do not
-
9
Page 10
CONDITIONING GUIDELINES
The following general guidelines will help you to plan
your exercise program. Remember that proper nutrition and adequate rest are essential for successful
results.
WARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for persons over the age
of 35 or persons with pre-existing health problems.
The pulse monitor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse monitor is intended only
as an exercise aid in determining heart rate
trends in general.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart in the centre of the
console shows recommended heart rates for fat burning, maximum fat burning, and cardiovascular (aerobic) exercise.
To find the proper heart rate for you, first find your age
on the left side of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
to the right of your age. The three numbers are your
“training zone.” The lowest number is the recommended heart rate for fat burning; the middle number is the
recommended heart rate for maximum fat burning; the
highest number is the recommended heart rate for
aerobic exercise.
Burning Fat
To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num
ber in your training zone as you exercise.
carbohydrate calories for ener-
.
-
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
HOW TO MEASURE YOUR HEART RATE
To measure your heart rate, first exercise for at least
four minutes. Then, stop pedalling and measure your
heart rate using the pulse sensor on the console.
WORKOUT GUIDELINES
Each workout should include the following three
important parts:
A warm-up, consisting of 5 to 10 minutes of stretching and light exercise. A proper warm-up increases
your body temperature, heart rate, and circulation in
preparation for strenuous exercise.
Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise program, do not keep your heart rate in your training
zone for longer than 20 minutes.)
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Caution: Be sure to progress at
your own pace and avoid overdoing it. Incorrect
or excessive training may result in injury to your
health.
Remember
regular and enjoyable part of your everyday life.
, the key to success is make exercise a
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num
ber in your training zone as you exercise.
-
10
Page 11
MAINTENANCE AND TROUBLE-SHOOTING
Inspect and tighten all parts of the exercise cycle
regularly
The exercise cycle can be cleaned with a soft, damp
cloth. Avoid spilling liquid on the console. Keep the
console out of direct sunlight or the display may be
damaged. Remove the batteries when storing the
exercise cycle.
HOW TO TIGHTEN THE CRANK
If the arms of the Crank (33) become loose, they
should be tightened in order to prevent excessive
wear. Loosen the Crank Nut (56) on the left arm of the
. Replace any worn parts immediately.
59
56
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. In order to adjust the
reed switch, the Left Side Shield (1) must be removed.
Using an adjustable wrench, turn the Left Pedal (28)
40
42
28
33
42
42
1
4
33
Crank. Place the end of a standard screwdriver in one
of the slots in the Crank Bearing Assembly (59).
Lightly tap the screwdriver with a hammer to turn the
Crank Bearing Assembly counterclockwise until the
arms are no longer loose. Do not overtighten the
Crank Bearing Assembly. When the Crank Bearing
Assembly is properly tightened, retighten the Crank
Nut.
BATTERY REPLACEMENT
If the console does not function properly
should be replaced. To replace the batteries, see
assembly step 2 on page 6. In addition, make sure
that the console wire is connected to the reed switch
wire.
, the batteries
clockwise and remove it from the Crank (33). Remove
the two Side Shield Screws (4) and the three M4 x
32mm Screws (42) from the Left Side Shield. Next, lift
the Side Shield Cover (40) off the Side Shields. Grasp
both Side Shields at the top and gently pull them
apart. Make sure that the arm of the Crank is in the
position shown in the drawing above. Carefully slide
the Left Side Shield forward off the arm of the Crank
and remove it.
Next, locate the
Reed Switch (54).
Turn the Crank (33)
until the Magnet
(55) is aligned with
the Reed Switch.
Loosen but do not
remove the M4 x
16mm Screw (9).
Slide the Reed
Switch slightly closer to or away from
the Magnet. Retighten the Screw
moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjust
ed, reattach the left side shield and pedal.
33
.
9
55
54
urn the Crank for a
T
-
11
Page 12
HOW TO ADJUST THE RESISTANCE STRAP
If there is not enough pedalling resistance when the
resistance knob is turned to the highest setting, the
Resistance Strap (47) may need to be adjusted.
adjust the Resistance Strap, the left side shield must
first be removed. Refer to the instructions at the left
and remove the left side shield.
Next, turn the
resistance knob
to the lowest setting. Locate and
open the Strap
Buckle (46). Grip
the end of the
Resistance Strap
(47) and pull it up
to remove any
slack. While
holding the end
of the Resistance Strap, fully close the Strap Buckle.
Turn the Crank (33) for a moment to make sure that
there is not too much resistance. When the Resistance Strap is properly adjusted, reattach the left side
shield and pedal.
HOW TO ADJUST THE BELT
The exercise cycle features a precision belt that must
be kept properly adjusted. If the belt causes excessive noise or slips as you pedal, the belt should be
checked. To do this, the left side shield must first be
removed. Refer to the instructions on page 11 and
remove the left side shield.
33
47
46
To
Next, use an
adjustable
wrench to turn
the right pedal
counterclock
wise and
remove it.
Remove the
right side
shield.
Press down on
the centre of
the Belt (16) between the front and rear pulleys.
There should be from 1/4” to 3/4” (6 to 19mm) of
vertical movement in the centerre of the Belt.
If the Belt (16)
is properly
adjusted, reattach the side
shields and pedals. If the Belt
needs to be
adjusted, loosen
the M8 Washer
Nut (34) on
each side of the
Flywheel (39).
To tighten the Belt, turn the two M6 Nuts (37) clockwise; to loosen the Belt, turn the Nuts counterclockwise. Make sure that the Flywheel is straight and tighten the M8 Washer Nuts (34). Reattach the side shields
and pedals.
-
34
16
16
39
37
12
Page 13
PART LIST—Model No. WLCCEX69571 R0500A
Key No. Qty. Description
1 1 Left Side Shield
2 1 Right Side Shield
3 2 Double Tree Fastener
4 4 Side Shield Screw
5 1 Handlebar
6 2 Foam Grip
7 1 Console
8 5 M10 x 25mm Button Screw
9 7 M4 x 16mm Screw
10 1 Resistance Knob
11 1 Resistance Cable
12 1 Knob Housing
13
14 1 Handlebar Post
15 1 Frame
16 1 Belt
17 1 Front Stabilizer
18 1 Rear Stabilizer
19 1 Seat
20 1 Seat Post
21 3 M8 Nylon Locknut
22 1 25.4mm x 50.8mm Bushing
23 1 38.1mm x 63.5mm Bushing
24 2 Wheel Hub
25 2 Wheel
26 2 Wheel Spacer
27 2 M6 x 16mm Self-tapping Screw
28 1 Left Pedal
29 1 Seat Knob
30 4 M10 x 70mm Carriage Bolt
31 4 M10 Nylon Locknut
1 Right Pedal
Key No. Qty. Description
32 1 Small Spring
33 1 Crank/Pulley
34 2 M8 Washer Nut
35 2 Adjustment Bolt
36 2 Adjustment Bracket
37 2 M6 Nut
38 1 Flywheel Axle
39 1 Flywheel
40 1 Side Shield Cover
41 5 M10 Split Washer
42 3 M4 x 38mm Screw
43 2 Flywheel Bearing
44
45 1 M4 x 16mm Flat Head Screw
46 1 Strap Buckle
47 1 Resistance Strap
48 2 Stabiliser Endcap
49 1 Large Spring
50 4 M6 Washer
51 1 M4 x 14mm Bolt
52 1 M4 Nut
53 3 M8 Split Washer
54 1 Reed Switch/Wire
55 1 Magnet
56 1 Crank Nut
57 2 Handlebar Endcap
58 1 Flywheel Spacer
59* 2 Crank Bearing Assembly
# 1 User’s Manual
# 1 Console Decal Sheet
# 1 Allen Wrench
* Includes all parts shown in the box
2 M10 Washer
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the page 15 of
this manual for information about ordering replacement parts.
13
Page 14
3
3
2
1
6
5
8
7
10
11
12
9
14
8
9
4
4
44
4
19
21
21
53
53
20
9
22
23
29
24
25
26
27
15
16
24
25
26
27
31
55
28
33
56
13
33
30
54
9
31
31
31
45
46
47
51
32
50
50
49
52
34
36
37
35
58
43
39
43
30
18
48
48
37
36
35
34
38
17
44
41
41
40
54
8
41
41
41
8
57
42
42
59*
59*
44
EXPLODED DRAWING—Model No. WLCCEX69571 R0500A
14
Page 15
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Monday–
Friday, 8:00 am–6:30 pm EST (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WLCCEX69571)
• The NAME of the product (WESLO
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 14 of this manual).
CUSTOMER RECORD
Serial No.: ____________________________ Purchase Date: _______________________________________
Retailer Name: ________________________ Retailer Address: ______________________________________
®
PURSUIT 795i)
PLACE
STAMP
HERE
of Canada Inc.
ICON
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
15
Page 16
LIMITED WARRANTY
®
of
/du Canada Inc.
™
ICON OF/DU CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of ninety (90) days from the date of purchase.
ty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing,
at ICON's option, the product at one of its authorised service centres. All products for which warranty claim is made
must be received by ICON at one of its authorised service centres with all freight and other transportation charges
prepaid, accompanied by suf
ficient proof of purchase. All returns must be pre-authorised by ICON. This warranty
does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorised service centre, to products used
for commercial or rental purposes, or to products used as store display models. No other warranty beyond that
specifically set forth above is authorised by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with
the use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly
, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any and all
other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its
scope and duration to the terms set forth herein. Some provinces do not allow limitations on how long an implied
warranty lasts.
Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to province or
so specified by the retailer of your equipment.
This warran-
ICON OF/DU CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUNTY:
MODEL NO.
SERIAL NO. PURCHASE DATE:
RETAILER NAME:
1) Primary user(s) of product:
o Male o Female o Family
Age of primary user:
2)
o 0–24 o 35–44 o 55–64
o 25–34 o 45–54 o 65 and over
3) Annual household income:
o 0–9,999 o 15,000–19,999
o 10,000–14,999 o 20,000+
4) How many times a week do you exercise?
o Less than 3 times o 3 times or more
5) Have you ever purchased a ICON product before?
o Ye s o No
6) Where did you first see or hear about ICON products?
o Magazine o Friend/relative
o Newspaper Ad o Store
o Other
What was the primary reason for purchasing this ICON product?
7)
o Store Employee o T
o Electronic Features o Magazine Ads o Price
o Product Design o Product Innovation
o Other Features
elevision
Ads
o Colour
PHONE:
POSTCODE:
RETAILER
PRODUCT WARRANTY REGISTRATION
ADDRESS:
8) Did you consider purchasing fitness equipment from another
manufacturer?
o No o Y
What other Manufacturer?
9) Based on your impression of what you have purchased,
would you buy another ICON product?
o Ye s o No o No Opinion
If not, what other brand name equipment would you purchase?
10) What other type of exercise equipment do you own?
o Bicycle o Exercise Cycle o T
o Home Gym o W
o Cardio Glide o Other
11) Which type of magazines do you read regularly?
o Sports o Fitness o Motoring
o Business o Computer o General
12) Do you wish to be sent further bulletins about ICON products?
o Ye s o No
2000 ICON of Canada, Inc. Printed in US
©
es
eight Bench
THANK YOU FOR YOUR TIME
readmill
o Stepper
WESLO®is a registered trademark of ICON Health & Fitness, Inc.
Part No. 166095 R0500A Printed in China © 2000 ICON Health & Fitness, Inc.
Loading...