Weidmuller IE-SW8-ECO User Manual

Page 1
Bedienungsanleitung
Industrial Ethernet 10/100 MBit/s Mini-Switch 2
Operating instructions
Industrial Ethernet 10/100 Mbps Mini-Switch 5
GB
\
IE-SW8-ECO 8829430000
%
Industrial Central Equipment
4EA4
For Use in Class 2 Circuits
Page 2
5
Operating instructions
The IE-SW8-ECO switching hub is designed for the Industrial Automation environment. Like all Ethernet switches from Weidmüller, it features non-blocking (full wire-speed) operation. It divi-
des an Ethernet network into five collision domains – “bridging” data links to create larger network dia­meters than possible with repeating hubs.
Each port automatically negotiates its data rate to 10 Mbps or 100 Mbps – controlling data flow with the PAUSE function in full-duplex links or with the backpressure method in half-duplex links.
Port assignments are learned by reading Ethernet frames and logging the source addresses to a table. Throughput is improved by restricting traffic to those ports party to a data exchange – while other data is simultaneously exchanged on other ports.
Store-and-forward operation is implemented and broadcast, multicast, or unicast transmissions are re­ceived by all ports.
The IE-SW8-ECO has five Auto-MDIX ports for attaching local devices. In addition to a power LED, each port has one LED showing link/activity/rate and one showing duplex status. The unit operates from a wide range of low-voltage AC or DC power.
The IE-SW8-ECO is provided with a writable label for easy identification of the remote device attached to each cable
Specifications
Electrical INPUT DC AC Voltage: 10-36 V8-24 V Power: 6 W 6 VA Frequency N/A 47-63Hz
Temperature Operating Temperature: 0 °C to +60 °C Storage Temperature: -40 °C to +85 °C
Mounting DIN-rail TS-35
Compliance CE­FCC, part 15, Class A EN50081-2 EN50082-2
\
%
Industrial Central Equipment
4EA4
For Use in Class 2 Circuits
Functional Compliance: ANSI/IEEE 802.3 Data Rates: 10 /100 Mbps Signaling: 10BaseT and 100BaseTX
Connectors: Shielded RJ-45 Segment Length: 100 m (max.)
LED- Indicators Power green Activityt/ Link green or yellow Duplex green
RJ45 Connector Pin Assignment Pin Funktion 1 TD+ 2 TD­3 RD+ 6 RD­(All other pins are unused.)
Page 3
6
Dimensional Drawing
Power Options
Power Considerations
Voltage in the range of 10-36 VDC or 8-24 VAC must deliver current commensurate with 6-watt power consumption. The recommended size for solid power conductors is 16-22 AWG; for stranded conduc­tors, use 16-18 AWG. Ground is directly connected to zero volts and the chassis is isolated from zero volts. Input connections are reverse-polarity protected.
LED Indicators
The “PWR” LED glows solid green when the switch is properly powered. To aid in troubleshooting, each port has two LEDs. The Port 1 LED labeled “L” glows solid if a link exists, flashes to show activity and shows data rate by color: green for 100 Mbps and yellow or 10 Mbps. The LED labeled “D” glows solid green if full-duplex is on or is unlit when that port is operating in half-duplex mode. The LEDs of Ports 1 and 2–5 are unlabeled but work the same.
25 mm
16 mm
100 mm
44.1 mm98 mm
50 mm
TS-35 DIN-Rail
PWR
Page 4
7
Network Connections
The switch employs Auto-MDIX technology so that either straight-through or crossover cables can be used to connect to network interface adapters or to another hub.
Warranty of this product
Weidmueller Interface GmbH & Co. KG warrants this product to the original purchaser for five year from the product’s shipping date. If a Weidmueller product fails to operate in compliance with its specification during this period, Weidmueller will, at its option, repair or replace the product at no charge. The custo­mer is, however, responsible for shipping the product; Weidmueller assumes no responsibility for the product until it is received. This warranty does not cover repair of products that have been damaged by abuse, accident, disaster, misuse,or incorrect installation. Weidmuellers limited warranty covers pro­ducts only as delivered. User modification may void the warranty if the modification damages the pro­duct, in which case this warranty does not cover repair or replacement.
This warranty in no way warrants suitability of the product for any specific application.
Manufacturer:
Weidmüller Interface GmbH & Co. KG Klingenbergstrasse 16 32758 Detmold Germany
Declaration of Conformitity
EMC Directive 89/336/EEC as amended by 92/31/EEC & 93/68/EEC; General Product Safety Directive 92/59/EEC
EN 55022:1995 (CISPR22: 1993), Class A; EN 50082-2:1995, EMC - Part 2: Industrial Environment
Connecting the chassis connection to earth is optional in all applications.
DC powered
AC powered
(ungrounded secondary)
AC powered
(grounded secondary)
AC powered with battery backup
Redundant DC
powered
Page 5
Loading...