Page 1
Model No. 831.150292
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
• Assembly
• Adjustments
• Troubleshooting
• Part List and Drawing
WEIGHT BENCH EXERCISER
User’s Manual
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
Patent Pending
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Page 2
Keep hands and
fingers clear of
this area.
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ADJUSTMENTS
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
FULL 90-DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
WARNING DECAL PLACEMENT
The warning decals
shown here have been
placed on the weight
bench in the locations
shown. If a decal is
missing or illegible,
please call toll-free
1-877-992-5999, Mon.
through Fri., 6 a.m.
until 6 p.m. Mountain
Time, to order a free
replacement decal.
Place the decal on the
weight bench in the
location shown.
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Keep the weight bench indoors, away from
moisture and dust. Do not put the weight
bench in a garage or covered patio, or near
water.
5. Use the weight bench only on a level surface. Cover the floor beneath the weight
bench to protect the floor.
6. Make sure all parts are properly tightened
each time the weight bench is used. Replace
any worn parts immediately.
10. Keep hands and feet away from moving parts.
11. The weight bench is designed to support a
maximum user weight of 300 pounds, and a
maximum total weight of 410 pounds. Do not
place more than 110 pounds, including a barbell and weights, on the weight rests. Do not
place more than 50 pounds on the leg lever.
12. Always make sure there is an equal amount
of weight on each side of your barbell when
you are using it. Always keep some weight
on both ends of the barbell when adding or
removing weights to prevent the barbell from
tipping.
13. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
14. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
7. Keep children under 12 and pets away from
the weight bench at all times.
8. Always wear athletic shoes for foot protection while exercising.
9. Do not use a barbell that is longer than six
feet with the weight bench. Note: The weight
bench does not include a barbell or weights.
15. When using the backrest in an inclined position, make sure that the support rod is
inserted completely through both uprights,
and that the support rod is turned to the
locked position.
16. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool
ing down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
-
3
Page 4
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER®PRO
220 weight bench. The weight bench offers an impressive array of weight stations designed to develop
every major muscle group of the body. Whether your
goal is to tone your body
and strength, or improve your cardiovascular system,
the weight bench will help you to achieve the specific
results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
ASSEMBLED
DIMENSIONS:
Height: 47 in.
Width: 30 in.
Depth: 62 in.
, build dramatic muscle size
reading this manual, call 1-800-4-MY-HOME
(1-800-469-4663). To help us assist you, please note
the product model number and serial number before
calling. The model number is 831.150292. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
®
Weight Rests
Upright
Leg Lever
Weight Tube
Backrest
Support Rod
Seat
4
Page 5
ASSEMBLY
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled successfully by anyone. However, it is important to
realize that the versatile weight bench has many
parts and that the assembly process will take
time. Most people find that by setting aside plenty of time, assembly will go smoothly.
Before beginning assembly, carefully read the
following information and instructions:
Assembly requires two people.
•
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1. Before assembling the weight bench, be sure
that you have read and understand the information in the box above.
Attach two Joint Plates (11) to the Upright (1)
without the warning decal with two M10 x 66mm
Bolts (28) and two M10 Nylon Locknuts (31). Do
not tighten the Locknuts yet.
Repeat this step with the other Upright (1).
Make sure the Joint Plates (11) are oriented as
shown in the inset drawing.
1
1
arning
W
Decal
11
31
11
28
1
5
Page 6
2. Attach the Crossbar (2) to an Upright (1) with two
M10 x 66mm Bolts (28), two Joint Plates (11),
and two M10 Nylon Locknuts (31).
tighten the Locknuts yet.
Do not
2
Repeat this step with the other Upright (1).
3. Attach the Front Leg (4) to the Bench Frame (3)
with an M10 x 66mm Bolt (28), an M10 x 19mm
Screw (5), an M10 Washers (30), and an M10
Nylon Locknut (31). Do not tighten the Locknut
or Screw yet.
1
1
31
11
28
3
11
2
5
28
3
Attach the Bench Frame (3) to the Crossbar (2)
4.
with two M10 x 68mm Bolts (27) and two M10
Nylon Locknuts (31).
31
30
4
4
27
2
3
31
6
Page 7
5. Insert the Support Rod (14) into a set of holes in
the Uprights (1). Turn the Support Rod so the
locking pin is wrapped around the Upright.
5
ighten the M10 Nylon Locknuts (31) and M10
T
x 19mm Screw (5) used in steps 1–5.
6. Lubricate the M10 x 60mm Bolt (25) with grease.
Attach the Leg Lever (6) to the Front Leg (4) with
the Bolt and an M10 Nylon Locknut (31).
overtighten the Locknut; the Leg Lever must
be able to pivot easily.
7. Slide a Pad Tube (12) into the Leg Lever (6).
Slide two Foam Pads (13) onto the ends of the
Pad Tube.
ented as shown.
Make sure the Foam Pads are ori-
Do not
6
7
Locking
13
14
1
Pin
31
25
4
6
Lubricate
6
Repeat this step with the other Pad Tube (12).
Insert a Weight Rest (15) into an Upright (1). Turn
8.
eight Rest so the locking pin is wrapped
the W
around the Upright.
Repeat this step with the other W
(15).
eight Rest
12
13
12
8
15
Locking
Pin
1
15
7
Page 8
9. Attach the Backrest Tubes (7) to the Backrest (8)
with four M6 x 38mm Screws (32) and four M6
ashers (22). Do not tighten the Screws yet.
W
Make sure that the name embroidery is in the
indicated location.
9
8
Name
Embroidery
22
7
22
32
32
10. Lubricate an M10 x 142mm Bolt (23) with grease.
Attach the Backrest Tubes (7) to the welded tube
on the Bench Frame (3) with the Bolt, two M10
Washers (30), and an M10 Nylon Locknut (31).
Do not overtighten the Locknut; the Backrest
Tubes must be able to pivot easily.
Tighten the M6 x 38mm Screws (32) used in
step 10.
11. Attach the Seat (9) to the Bench Frame (3) with
four M6 x 16mm Screws (24).
Seat is oriented as shown.
12. Make sure that all parts are properly tightened
before you use the weight bench. The use of
all remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
Make sure the
10
11
31
30
7
3
Tube
9
Lubricate
3
24
30
23
Rounded
Edge
24
8
Page 9
ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 10 for important exercise information
and refer to the accompanying exercise guide to see the correct form for each exercise. Refer also to the
exercise information accompanying your weight set for additional exercises.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
1
The Backrest (8) can be used in a decline position, a
level position, or two incline positions. To use the
Backrest in the decline position, remove the Support
Rod (14) and lay the Backrest on the Crossbar (2).
To use the Backrest (8) in the level position, lift the
Backrest and insert the Support Rod (14) through the
bottom set of holes in the Uprights (1). Rotate the
locking pin into place around the Upright.
To use the Backrest (8) in an incline position, lift the
Backrest and insert the Support Rod (14) through an
upper set of holes in the Uprights (1). Rotate the locking pin into place around the Upright.
8
14
1
WARNING: When using the
Backrest (8) in a level or incline position,
insert the Support Rod (14) completely
through both Uprights (1) and turn it to the
locked position.
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (6), slide the desired weights
(not included) onto the weight tube.
WARNING: Do not place more
than 50 pounds on the Leg Lever (6).
ADJUSTING THE WEIGHT RESTS
To change the height of the Weight Rests (15),
remove them from the Uprights (1) and insert them
into the desired set of holes. Rotate the W
so that the locking pins wrap around the Uprights.
eight Rests
W
15
eight
T
ube
2
6
Weight
Locking
Pin
Locking
Pin
15
WARNING: Always set both
eight Rests (15) at the same height.
W
1
1
9
Page 10
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
right for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of resistance and increase the number of repetitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by completing more sets rather than by using high amounts of
resistance.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross T
Cross training is an ef
well-balanced fitness program.
anced program is:
• Plan strength training workouts on Monday,
W
Plan 20 to 30 minutes of aerobic exercise, such as
•
running on a treadmill or riding on an exercise bike,
on
Rest from both strength training and aerobic exercise
•
for at least one full day each week to give your body
time to regenerate.
The combination of strength training and aerobic exer
cise will reshape and strengthen your body, plus develop your heart and lungs.
raining
ficient way to get a complete and
ednesday
Tuesday and Thursday.
, and Friday
An example of a bal
.
-
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
fective exercise program.
ef
through the full range of motion for each exercise, and
moving only the appropriate parts of the body
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles af
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing.
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
-
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
fected. Refer to the muscle chart on the
This requires moving
The exertion stage of
.
-
10
Page 11
Rest for a short period of time after each set. The
O
P
Q
R
S
T
U
V
X
W
N
M
J
G
F
H
I
K
E
C
D
B
A
L
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
ideal resting periods are:
Rest for three minutes after each set for a muscle
•
building workout.
Rest for one minute after each set for a toning work-
•
out.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List the
date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to achieving the greatest results is to make exercise a regular
and enjoyable part of your everyday life.
11
Page 12
M6 Washer (22)
M10 Nylon Locknut (31)
M10 x 142mm Bolt (23)
M10 x 60mm Bolt (25)
M10 x 68mm Bolt (27)
M10 x 66mm Bolt (28)
M6 x 16mm Screw (24)
M6 x 38mm Screw (32)
M10 x 19mm Screw (5)
M10 Washer (30)
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part, from the PART LIST.
pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has
been pre-assembled. If a part is missing, call toll-free 1-877-992-5999.
Important: Some parts may have been
Page 13
PART LIST—Model No. 831.150292 R1104B
Key No.
1 2 Upright
2 1 Crossbar
3 1 Bench Frame
4 1 Front Leg
5 1 M10 x 19mm Screw
6 1 Leg Lever
7 2 Backrest Tube
8 1 Backrest
9 1 Seat
10 2 Upright Cover
11 4 Joint Plate
12 2 Pad Tube
13 4 Foam Pad
14 1 Support Rod
15 2 Weight Rest
16 3 50mm Square Inner Cap
17 1 25mm Round Angled Cap
18 2 38mm Square Inner Cap
19 4 25mm Square Inner Cap
“#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
this manual for information on ordering replacement parts.
Qty. Description Key No. Qty. Description
20 2 25mm Round Inner Cap
21 2 21mm Round Inner Cap
22 4 M6 Washer
23 1 M10 x 142mm Bolt
24 4 M6 x 16mm Screw
25 1 M10 x 60mm Bolt
26 6 25mm x 50mm Inner Cap
27 2 M10 x 68mm Bolt
28 9 M10 x 66mm Bolt
29 4 M4 x 16mm Screw
30 3 M10 Washer
31 13 M10 Nylon Locknut
32 4 M6 x 38mm Screw
33 1 25mm Round (Thick) Inner Cap
34 4 19mm Square Inner Cap
# 1 User’s Manual
# 1 Exercise Guide
# 1 Grease Pack
Page 14
3
9
16
4
6
5
13
12
13
1
11
2
10
1
10
20
15
14
7
7
8
11
11
11
13
12
13
15
16
26
26
26
26
16
26
26
18
18
34
34
34
34
33
17
19
19
21
21
20
23
32
32
24
24
25
27
28
28
28
29
29
29
29
3022
30
22
31
30
31
31
31
31
31
EXPLODED DRAWING—Model No. 831.150292 R1104B
Page 15
FULL 90-DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States
and Sears will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for
rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
104B
15 R1
Part No. 221
1
Printed in China
2004 Sears, Roebuck and Co.
©
Loading...