Page 1
Model No. 831.290241
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and instructions
in this manual before using this
equipment. Save this manual for
future reference.
Serial Number
Decal
USER’S MANUAL
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Patent Pending
SEARS, ROEBUCK AND CO.,
HOFFMAN ESTATES, IL 60179
Page 2
Adjusting the Press Plate
To adjust the distance
between the Small Seat
(29) and the Press Plate
(6), remove the Adjustment
Pin (26) from the Base (2).
Slide the Adjustment Frame
(3) into or out of the Base
until the Press Plate is in
the correct position for the
exercise to be performed.
Note: For the correct starting positions, refer to the
Exercise Guide section of this manual. Insert the
Adjustment Pin into the indicated hole in the Base and a
hole in the Adjustment Frame.
This section explains how the body toning system can be adjusted. Inspect and tighten all parts each time you use the
body toning system. Replace any worn parts immediately. The body toning system can be cleaned with a damp cloth
and a mild, non-abrasive detergent. Do not use solvents.
Adjusting the Resistance
To change the amount of
resistance, remove the four
Spring Clips (5) from the
bench. Attach the 25-lb.
Bands (25) to the bars on
the Base (2) and the Pivot
Frame (7). Secure the
Bands with the four Spring
Clips.
The 10-lb. Bands (28) can be attached in the same manner. Attach both sets of Bands for maximum resistance.
WARNING:
Always place an equal
amount of resistance on each side of the body toning system.
WARNING: To reduce the risk of serious injury, read the following important precautions before
using the body toning system.
5
26
2
3
6
29
Bar
2
Bar
7
25
Adjusting The Body Toning System
Important Precautions
1. Read all instructions in this manual before using
the body toning system. Use the body toning
system only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the body toning system are adequately informed of all precautions.
3. The body toning system is intended for home
use only. Do not use the body toning system in a
commercial, rental or institutional setting.
4. The body toning system is designed to support a
maximum of 250 pounds.
5. Always make sure there is an equal amount of
resistance on each side of the body toning system. Only use the included bands; do not add
additional bands.
6. Keep children under 12 and pets away from the
body toning system at all times.
7. Use the body toning system only on a level surface. Cover the floor beneath the body toning
system to protect the floor.
8. Inspect and tighten all parts each time you use
the body toning system. Replace any worn parts
immediately.
9. Always wear athletic shoes for foot protection
while exercising.
10. Keep hands and feet away from moving parts.
11. I
f you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling
down.
WARNING: Before beginning this or any exercise program, consult your physician. This is
especially important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
Page 3
Thank you for selecting the versatile WEIDER®TWO
TONE body toning system. The TWO TONE body toning
system is designed to help you develop major muscle
groups of the body. Whether your goal is a shapely figure,
improvement in muscle size and strength, or a healthier
cardiovascular system, the TWO TONE body toning system will help you achieve the specific results you want.
For your benefit, read this manual carefully before
using the WEIDER
®
TWO TONE body toning system. If
you have additional questions, please call our toll-free
HELPLINE at 1-800-736-6879, Monday through Saturday,
7 a.m. until 7 p.m. Central Time (excluding holidays). To
help us assist you, please mention the product model
number (831.290241) and the serial number found on a
decal attached to the body toning system (see the front
cover of this manual).
1. Press two 2” Round
Outer Caps (23)
onto each of the two
Front Stabilizers (9)
and the two Rear
Stabilizers (not
shown). Note: The
Front Stabilizers
are shorter than the Rear Stabilizers.
Attach a Front Stabilizer (9) to the Ab Leg (12) with two
M8 x 63mm Carriage Bolts (31) and two M8 Nylon
Locknuts (34). Attach a Rear Stabilizer (not shown) to
the other end of the Ab Leg in the same manner.
2. Insert an M8 x
77mm Carriage Bolt
(41) into the center
hole in the Large
Support Plate (14).
Attach the Large
Support Plate to the
Large Seat (13) with
two M6 x 16mm
Button Screws (40).
Press a 1” x 2” Inner
Cap (30) into each
end of the Seat
Frame (15).
Insert an M8 x 77mm Carriage Bolt (41) into the indicated hole in the Seat Frame (15). Insert the M8 x
77mm Carriage Bolt in the Large Support Plate (14)
through the rear hole in the Seat Frame.
Attach the Large Seat (13) to the Seat Frame (15) with
the M6 x 16mm Button Screw (40).
Secure the two M8 x 77mm Carriage Bolts (41) to the
Ab Leg (12) with two M8 Washers (35) and two M8
Nylon Locknuts (34).
1
3. Hold the Ab Frame
(11) as shown.
Slide two M8 x
40mm Button Bolts
(33) through the Ab
Frame and the Seat
Frame (15). Secure
the Bolts with two
M8 Washers (35)
and two M8 Nylon
Locknuts (34).
4. If there are M6 x
34mm Button Bolts
(47) in the ends of
the Ab Frame (11),
remove them.
Wet the Ab Frame
(11) and the inside
of the Short
Sleeves (48) with
soapy water. Slide
the two Short
Sleeves onto the Ab
Frame, making sure
the angled ends
face each other.
Hold the Ab Handlebars (10) as shown, and attach
them to the Ab Frame (11) with the two M6 x 34mm
Button Bolts (47) and two M6 Nylon Locknuts (44).
Press a 28.6mm Round Inner Cap (16) into each Ab
Handlebar.
Wet the Ab Handlebars (10) and the inside of the
Long Sleeves (49) with soapy water. Slide the two
Long Sleeves onto the Ab Handlebars and the Ab
Frame (11), so that they cover the M6 x 34mm Button
Bolts (47) and the M6 Nylon Locknuts (44). Make
sure the angled ends of the Long Sleeves are by the
28.6mm Round Inner Caps (16).
2
3
11
33
23
23
34
12
34
31
13
15
14
41
41
40
12
40
40
30
34
35
9
35
34
30
15
4
10
10
11
16
44
47
47
48
49
44
16
Before You Begin
Assembly—AB TILT & TONE
Page 4
5. Attach a Rear
Stabilizer (8) to the
Base (2) with two
M8 x 63mm
Carriage Bolts (31)
and two M8 Nylon
Locknuts (34).
6. Attach a Front
Stabilizer (9) to the
Adjustment Frame
(3) with two M8 x
63mm Carriage
Bolts (31) and two
M8 Nylon Locknuts
(34).
Press the 30mm
Square Inner Cap (17) into the Adjustment Frame (3)
and secure it with the M4 x 12mm Screw (39). Slide
the Adjustment Frame through the Slider Bushing (27)
and into the Base (2). Insert the Adjustment Pin (26)
into the indicated hole in the Base and a hole in the
Adjustment Frame.
Attach the Press Plate (6) to the Adjustment Frame (3)
with two M8 x 43mm Carriage Bolts (32), two M8
Washers (35), and two M8 Nylon Locknuts (34).
7. Make sure the End
Plate (19) is inside
the Angled Cap
(18). Press the
Angled Cap onto
the bottom end of
the Backrest
Frame (1). Press a
38mm Square
Inner Cap (24) into
the top of the
Backrest Frame.
Attach the Pivot
Frame (7) to the
Backrest Frame (1)
with two M8 x
52mm Button Bolts
(42), two M8 Washers (35), and two M8 Nylon
Locknuts (34).
Attach the Pivot Frame (7) to the Base (2) with an M10
x 64mm Bolt (37) and an M10 Nylon Locknut (36). Do
not over tighten the Locknut; the Pivot Frame must
be able to pivot easily.
8. Slide a Grip (22)
onto each end of the
Handlebar (21).
Attach the
Handlebar (21) to
the Backrest Frame
(1) with two M8 x
52mm Button Bolts
(42), two M8
Washers (35), and
two M8 Nylon
Locknuts (34).
Attach the Small Seat (29) to the Handlebar (21) with
two M6 x 42mm Button Screws (46) and two M6
Washers (38).
9. Insert an M6 x
50mm Carriage Bolt
(45) into the center
hole of the Support
Plate (20).
Attach the Support
Plate (20) to the
Backrest (4) with
two M6 x 16mm
Button Screws (40).
Attach the Backrest (4) to the Backrest Frame (1) with
the M6 x 50mm Carriage Bolt (45), an M6 Washer
(38), and an M6 Nylon Locknut (44).
Secure the Backrest (4) with an M6 x 55mm Button
Screw (43) and an M6 Washer (38).
The use of the remaining parts will be explained in
Adjusting The Body Toning System.
7
8
9
26
27
17
34
34
35
31
24
1
42
35
35
18
19
2
7
34
36
37
34
9
2
3
39
32
29
1
22
22
21
42
46
38
42
38
34
35
4
20
40
45
44
38
38
43
1
35
6
5
31
8
34
34
2
6
Assembly—ROCK & TONE
Page 5
Ab Crunch
Twist
Back Extension
Side To Side*
One Leg Side Squat with Leg Extension
One Leg Squat with Leg Extension
One Leg Side Squat
One Leg Squat
Calf Raise
Leg Press
Exercise Guide
Cross Over**
Circulate
Criss Cross
Lower Ab Crunch
Crunch With Knee Lift
*This exercise can be performed leaning forward, upright, or lean-
ing back.
**From the starting position, lean back (see Back Extension), and
then to the finishing position.
Included with the TWO TONE body toning system
is an exercise video. This video will motivate and
guide you through a 30-minute workout, helping
you get the maximum benefit from the body toning
system. The personal trainer will demonstrate the
correct form for each of the exercises that can be
performed with the AB TILT & TONE and the
ROCK & TONE.
Page 6
Key
Qty. Description
No.
Key
Qty. Description
No.
Key
Qty. Description
No.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this
user’s manual for information about ordering replacement parts.
Part List—Model No. 831.290241
R0701A
Part Identification Chart
1 1 Backrest Frame
2 1 Base
3 1 Adjustment Frame
4 1 Backrest
5 4 Spring Clip
6 1 Press Plate
7 1 Pivot Frame
8 2 Rear Stabilizer
9 2 Front Stabilizer
10 2 Ab Handlebar
11 1 Ab Frame
12 1 Ab Leg
13 1 Large Seat
14 1 Large Support Plate
15 1 Seat Frame
16 2 28.6mm Round Inner
Cap
17 1 30mm Square Inner Cap
18 1 Angled Cap
19 1 End Plate
20 1 Support Plate
21 1 Handlebar
22 2 Grip
23 8 2” Round Outer Cap
24 1 38mm Square Inner Cap
25 2 25-lb. Band
26 1 Adjustment Pin
27 1 Slider Bushing
28 2 10-lb. Band
29 1 Small Seat
30 2 1” x 2” Inner Cap
31 8 M8 x 63mm Carriage Bolt
32 2 M8 x 43mm Carriage Bolt
33 2 M8 x 40mm Button Bolt
34 18 M8 Nylon Locknut
35 10 M8 Washer
36 1 M10 Nylon Locknut
37 1 M10 x 64mm Bolt
38 4 M6 Washer
39 1 M4 x 12mm Screw
40 5 M6 x 16mm Button
Screw
41 2 M8 x 77mm Carriage Bolt
42 4 M8 x 52mm Button Bolt
43 1 M6 x 55mm Button
Screw
44 3 M6 Nylon Locknut
45 1 M6 x 50mm Carriage Bolt
46 2 M6 x 42mm Button Screw
47 2 M6 x 34mm Button Bolt
48 2 ShortSleeve
49 2 Long Sleeve
# 1 User’s Manual
# 1 Exercise Video
M8 x 77mm Carriage Bolt (41)
M8 x 63mm Carriage Bolt (31)
M4 x 12mm
Screw (39)
M10 x 64mm Button Bolt (37)
M6 x 50mm Carriage Bolt (45)
M8 x 52mm Button Bolt (42)
M6 x 34mm Button Bolt (47)
M6 x 42mm Button Screw (46)
M8 Washer (35)
M6 Washer (38)
M8 x 40mm Button Bolt (33)
M8 x 43mm Carriage Bolt (32)
M6 Nylon
Locknut (44)
M8 Nylon
Locknut (34)
M6 x 16mm Button Screw (40)
M6 x 55mm Button Screw (43)
M10 Nylon
Locknut (36)
Page 7
Exploded Drawing—Model No. 831.290241
R0701A
43
38
7
34
24
44
34
38
31
40
35
19
18
42
10
13
42
47
23
22
44
34
33
11
16
30
41
40
40
23
34
47
10
14
35
41
34
34
48
44
49
30
8
35
34
35
15
40
12
34
16
4
20
45
1
35
29
42
21
38
22
46
23
34
8
23
5
34
37
25
36
28
9
23
2
32
34
26
17
27
31
39
3
34
23
31
6
23
35
34
23
9
31
Page 8
The decal shown below has been applied to the body
toning system in the indicated locations. If the decal is
missing, or if it is not legible, please call our toll-free
HELPLINE at 1-800-736-6879, Monday through
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays), to order a free replacement decal. Apply the
replacement decal in the location shown.
Ordering Replacement Parts
Warning Decal
Full 90-Day Warranty
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this SEARS
BODY TONING SYSTEM, contact the nearest SEARS Service Center throughout the United States and SEARS
will repair or replace the BODY TONING SYSTEM, free of charge.
This warranty does not apply when the BODY TONING SYSTEM is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 176258 R0701A Printed in China © 2001 Sears, Roebuck and Co.
The model number and serial number of your WEIDER
®
TWO TONE body toning system are listed on a decal
attached to the frame. See the front cover of this manual
to find the location of the decal.
All replacement parts are available for immediate purchase
or special order when you visit your nearest SEARS
Service Center. To request service or to order parts by
telephone, call the toll-free numbers listed above.
When requesting help or service, or ordering parts, please
be prepared to provide the following information:
• The MODEL NUMBER of the product (831.290241)
• The NAME of the product (WEIDER
®
TWO TONE body
toning system)
• The PART NUMBER and DESCRIPTION of the PART
(see the PART LIST and the EXPLODED DRAWING)
QUESTIONS?
If you find that:
• you need help assembling or operating the
WEIDER®Two Tone
• a part is missing
• or you need to schedule repair service
call our toll-free HELPLINE
1-800-736-6879
Monday–Saturday, 7 a.m.–7 p.m. Central Time
(excluding holidays)
REPLACEMENT PARTS
If parts become worn and need to be replaced,
call the following toll-free number
1-800-FON-PART
(1-800-366-7278)
!
WARNING
• Misuse of this product may result in serious
injury.
• Read user’s manual and follow all warnings
and operating instructions prior to use.
• Do not allow children on or around machine.
• Replace label if damaged, illegible, or removed.
Loading...