Page 1
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our
factory.
TO AVOID DELA YS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The technicians on our customer
hot line will provide immediate
assistance, free of charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WEBE08920
Serial No.
Write the serial number in the
space above for reference.
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual for future reference.
Serial Number Decal (under seat)
USER’S MANUAL
Patent Pending
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Page 2
WARNING DECAL PLACEMENT
TABLE OF CONTENTS
2
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: APART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.
The decals shown here have
been placed on the weight
bench in the locations shown. If
a decal is missing or illegible,
please call our Customer
Service Department toll-free at
1-800-999-3756, Monday
through Friday, 6 a.m. until 6
p.m. Mountain Time, to order a
free replacement decal. Apply
the replacement decal in the
location shown.
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
!
WARNING
• Misuse of this
product may result in
serious injury.
• Read user’s manual
and follow all warnings
and operating instructions prior to use.
• Do not allow children
on or around machine.
• Replace label if
damaged, illegible,
or removed.
Keep hands and
fingers clear of
this area.
Page 3
3
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
5. Make sure all parts are properly tightened
each time you use the weight bench. Replace
any worn parts immediately.
6. Keep children under 12 and pets away from
the weight bench at all times.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protection while exercising.
9. The weight bench is designed to support a
maximum user weight of 300 pounds. Do not
place more than 110 pounds, including the
barbell, on the weight rests. Do not place
more than 110 pounds on the lat tower. Do
not place more than 50 pounds on the leg
lever. Note: The weight bench does not
include a barbell or weights.
10. Always keep an equal amount of weight on
both ends of your barbell when you are
using it. When adding or removing weights,
always keep some weight on both ends of
the barbell to prevent the barbell from tipping.
11. Do not use a barbell that is longer than six
feet with the weight bench.
12. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
13. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
14. Always set both weight rests at the same
height. Make sure that the adjustment knobs
are inserted completely and tightened into
the uprights before beginning any exercise.
15. When adjusting the position of the backrest,
make sure the adjustment tube is securely
seated in the adjustment brackets.
16. Always remove the curl post and lat tower
from the front leg before performing leg curls
with the leg lever.
17. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
WARNING:Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
IMPORTANT PRECAUTIONS
Page 4
BEFORE YOU BEGIN
4
Thank you for selecting the versatile WEIDER®160
weight bench. The WEIDER®160 weight bench is
designed to be used with your own weight set (not
included) to help you develop every major muscle
group of the body. Whether your goal is a shapely figure, dramatic increase in muscle size and strength, or
a healthier cardiovascular system, the WEIDER
®
160
will help you achieve the specific results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE08920. The serial number can be
found on a decal attached to the weight bench (see
the front cover of this manual).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
Lat Bar
Lat Tower
Weight Carriage
Seat
Leg Lever
Weight Tube
Curl Pad
Adjustment Tube
Backrest
Weight
Rests
ASSEMBLED
DIMENSIONS:
Height: 77 in.
Width: 49 in.
Depth: 71 in.
Page 5
5
1.
Press a 38mm Square Inner Cap (32) into the
end of the Bench Frame (1).
Attach the Bench Frame (1) to the Front Leg (2)
using two M8 x 55mm Bolts (22), two M8
Washers (41), and two M8 Nylon Locknuts (43).
Do not tighten the Locknuts yet.
2. Insert a 25mm x 50mm Inner Cap (24) into the
Left Base (3). Attach the Left Base to the Bench
Frame (1) using an M8 x 35mm Carriage Bolt
(36), an M8 x 68mm Bolt (28), and two M8 Nylon
Locknuts (43). Do not tighten the Nylon
Locknuts yet.
Attach the Left Upright (4) to the Left Base (3)
with two M8 x 35mm Carriage Bolts (36) and two
M8 Nylon Locknuts (43). Be sure the indicated
nuts are oriented as shown. Do not tighten the
Nylon Locknuts yet.
Repeat this step with the Right Base (7) and
the Right Upright (5).
1
32
1
2
43
41
41
22
22
2
5
4
24
24
Nuts
43
43
7
3
36
36
28
1
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two people.
• For help identifying small parts, refer to the PART
IDENTIFICATION CHART.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Make Things Easier for Yourself
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. Most people find that by setting
aside plenty of time, assembly will go smoothly.
ASSEMBLY
Before assembling the weight bench, make
sure that you have read and understand the
information in the box above.
Page 6
4
6
3. Attach the Storage Tube (51) to the Right Base
(7) with two M8 x 35mm Carriage Bolts (36) and
two M8 Nylon Locknuts (43).
Press a 45mm x 38mm Bushing (23) onto the
Left Upright (4). Slide a Weight Rest (6) into the
Upright and secure it at the desired height with a
54mm Adjustment Knob (27).
Secure the other Weight Rest (6) to the Right
Upright (5) in the same manner. Be sure that
both Weight Rests are set at the same height.
3
6
6
5
4
27
23
23
27
36
7
43
43
51
4. Press two 38mm Square Inner Caps (32) into the
ends of the Leg Lever (9). Press two 25mm
Round Inner Caps (21) into the ends of the
weight tube.
Insert four 19mm Round Inner Caps (47) into the
ends of two Pad Tubes (48). Slide the Pad Tubes
into the holes at the ends of the Leg Lever (9).
Slide four Foam Pads (33) onto the ends of the
Pad Tubes.
33
32
Weight
Tube
32
33
33
21
33
47
47
47
47
48
48
21
9
5. Lubricate the M10 x 67mm Bolt (46). Attach the
Leg Lever (9) to the Front Leg (2) using the Bolt
and an M10 Nylon Locknut (45). Do not over-
tighten the Nylon Locknut; the Leg Lever
must be able to pivot easily.
Press two 19mm Round Inner Caps (47) into the
ends of a Pad Tube (48). Slide the Pad Tube
through the hole in the Front Leg (2). Slide a
Foam Pad (33) onto each end of the Pad Tube.
5
33
33
46
Lubricate
9
45
47
47
48
2
Page 7
7
7. Press two 25mm Square Inner Caps (39) into the
Adjustment Tube (37). With the pins on the
Adjustment Tube facing downward, slide the
Adjustment Tube into a set of adjustment brackets on the Uprights (4, 5).
Lubricate an M10 x 168mm Bolt (40). Attach the
Backrest Tubes (20) to the Bench Frame (1) with
the Bolt, two M10 Washers (29), and an M10
Nylon Locknut (45). Do not overtighten the
Nylon Locknut; the Backrest Tubes must be
able to pivot freely.
Tighten the M8 Nylon Locknuts (43) used in
step 2, and the four M6 x 38mm Screws (14)
used in step 6.
7
39
39
45
29
29
40
37
20
Bracket
Lubricate
4
5
1
6
20
14
14
14
14
15
Narrow
End
31
31
31
31
39
39
6. Press four 25mm Square Inner Caps (39) into the
ends of the Backrest Tubes (20). Be sure the
Caps are oriented as shown.
Attach the Backrest (15) to the Backrest Tubes
(20) using four M6 x 38mm Screws (14) and four
M6 Washers (31). Be sure the narrow end of
the Backrest is on the end shown. Do not
tighten the Screws yet.
8. Attach the Seat (16) to the Bench Frame (1)
using two M6 x 16mm Screws (10), an M6 x
50mm Screw (38), and an M6 Washer (31).
8
38
31
16
10
1
Page 8
8
10. Press a 38mm Square Inner Cap (32) into the top
of the Lat Tower (11).
Route the Cable (25) around the Pulley (26) as
indicated. Attach the Pulley inside the slot in the
Lat Tower (11) with an M10 x 55mm Bolt (49), two
M10 Washers (29), two M10 Spacers (42), and
an M10 Nylon Locknut (45). Do not overtighten
the Nylon Locknut; the Pulley must be able to
turn freely.
Attach the Cable Clip (35) to the end of the Cable
(25).
10
11. Slide the Lat Tower (11) into the Front Leg (2).
Tighten it in place with the 44mm Adjustment
Knob (34).
11
32
11
42
29
49
26
42
29
45
25
35
34
2
11
9. Press two 25mm Round Inner Caps (21) into the
weight tube of the Weight Carriage (12). Press
two 45mm x 38mm Outer Bushings (23) onto the
top and bottom of the Weight Carriage.
Insert an M8 x 16mm Bolt (44) into the bracket on
the Weight Carriage (12). Slide the Weight
Carriage onto the Lat Tower (11) as shown.
Route the Cable (25) through the slot of the Lat
Tower (11) in the indicated direction. Connect the
eyelet on the Cable to the Weight Carriage (12)
using the M8 x 16mm Bolt (44) and an M8 Nylon
Locknut (43).
9
Weight
Tube
Slot
Bracket
25
43
44
21
21
12
23
23
11
12. Wet the ends of the Lat Bar (18) with soapy
water. Slide a Handgrip (19) onto each end of the
Lat Bar. Attach the Lat Bar to the Cable Clip (35)
and place it in the lat bar rest on the Lat Tower
(11).
12
19
19
35
18
11
Lat Bar
Rest
Page 9
ADJUSTMENTS
9
13
13. Attach the Curl Pad (17) to the Curl Post (13)
using two M6 x 16mm Screws (10). The Curl
Post and the Lat Tower attach to the weight
bench in the same place. Instructions for
switching between the Curl Post and the Lat
Tower can be found in the following section.
14. Make sure all parts are properly tightened
before you use the weight bench.
17
13
10
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 12 for important information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
The Backrest (15) can be set to three different positions: a level position, a decline position, and an
incline position.
To change the position of the Backrest (15), move the
Adjustment Tube (37) to a different set of adjustment
brackets on the Uprights (4, 5).
Make sure the Adjustment Tube (37) is securely
seated in the adjustment brackets.
15
Brackets
5
4
37
11
18
35
25
ATTACHING THE LAT BAR TO THE LAT TOWER
To use the Lat Tower (11), attach the Lat Bar (18) to
the Cable (25) with a Cable Clip (35).
Page 10
10
ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE AND LEG LEVER
To use the Lat Tower (11) or the Leg Lever (9), slide
the desired amount of weight (not included) onto the
indicated weight tubes. Secure the weights onto the
Weight Carriage (12) with the two Weight Clips (50).
WARNING:Do not place more
than 50 pounds on the Leg Lever (9), or more
than 110 pounds on the Weight Carriage (12).
12
50
50
11
9
Weight
Tube
Weight
Tube
ADJUSTING THE WEIGHT RESTS
To change the height of the Weight Rests (6), first
remove your barbell (not included) from the
Weight Rests. Remove the 54mm Adjustment Knobs
(27) from both Uprights (4, 5). Position the Weight
Rests at the desired height and align the holes in the
Weight Rests and the Uprights. Secure the Weight
Rests with the Adjustment Knobs. Make sure that
you fully tighten the Adjustment Knobs.
WARNING:
The Adjustment Knob
(27) must be inserted through both the Weight
Rest (6) and the Upright (4, 5), and be firmly
tightened. Always set both Weight Rests at
the same height. Never tighten a Knob into an
Upright before inserting the Weight Rest.
6
6
5
4
27
ATTACHING THE CURL POST OR LAT TOWER
For some exercises, the Curl Post (13) must be
attached to the weight bench. Insert the Curl Post into
the Front Leg (2). Align the holes in the Front Leg and
the Curl Post and secure the Curl Post with the
44mm Adjustment Knob (34). Make sure that you
fully tighten the Knob.
For other exercises, the Lat Tower (11) must be
attached to the weight bench. Insert the Lat Tower
into the Front Leg (2). Align the holes in the Front Leg
and the Lat Tower and secure the Lat Tower with the
44mm Adjustment Knob (34). Make sure that you
fully tighten the Adjustment Knob.
34
13
11
2
Page 11
11
15
51
17
16
6
6
9
FOLDING THE BACKREST
To perform squat exercises, you will need to fold the
Backrest (15) to the upright position.
To fold the Backrest (15), lift and pull it forward as far
as it will go. It will be held in place by its own weight.
STORING THE CURL PAD
When the Curl Pad (17) is not in use, it can be stored
in the Storage Tube (51). However, for some exercises, the Curl Pad should be stored away from the
weight bench so it does not interfere with the exercise.
WARNING:Always fold the
Backrest (15) out of the way when performing
squat exercises. Do not sit on the Seat (16)
when the Backrest is folded.
Always place 50 pounds on the Leg Lever (9)
to balance the weight bench when performing
squat exercises.
Do not stand with your back to the weight
bench when performing squat exercises. You
should be able to see the Weight Rests (6)
while exercising so that you can safely return
the barbell when you finish the exercise.
Page 12
12
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your
muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You
can adjust the intensity level of an individual exercise
in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A“set” is a series of
repetitions.)
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is
right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight.
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a moderate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross Training
Cross training is an efficient way to get a complete
and well-balanced fitness program. An example of a
balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exercise will reshape and strengthen your body, plus
develop your heart and lungs.
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed, is an individual matter. It is important to avoid
overdoing it during the first few months of your exercise program. You should progress at your own pace
and be sensitive to your body’s signals. If you experience pain or dizziness at any time while exercising,
stop immediately and begin cooling down. Find out
what is wrong before continuing. Remember that adequate rest and a proper diet are important factors in
any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise,
and moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
13 to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
EXERCISE GUIDELINES
Page 13
13
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning workout.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. The
chart on pages 14 and 15 of this manual can be photocopied and used to schedule and record your workouts. List the date, the exercises performed, the
weight used, and the numbers of sets and repetitions
completed. Record your weight and key body measurements at the end of every month. Remember, the
key to achieving the greatest results is to make exercise a regular and enjoyable part of your everyday
life.
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
Q. Triceps (back of arm)
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
A
B
C
D
E
G
H
I
J
K
F
M
L
T
N
O
P
Q
R
S
U
V
W
Page 14
14
MONDAY
Date:
/ /
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
AEROBIC EXERCISE
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
FRIDAY
Date:
/ /
Make photocopies of this page for scheduling and recording your workouts.
Page 15
15
MONDAY
Date:
/ /
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
AEROBIC EXERCISE
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
FRIDAY
Date:
/ /
Make photocopies of this page for scheduling and recording your workouts.
Page 16
Part No. 187091 R0702B Printed in China © 2002 ICON Health & Fitness, Inc.
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WEBE08920)
• The NAME of the product (WEIDER
®
160 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the center of this manual)
ORDERING REPLACEMENT PARTS
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Page 17
REMOVE THIS PART IDENTIFICATION CHART
PART LIST/EXPLODED DRAWING
SAVE THIS PART IDENTIFICATION CHART
PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
81
Page 18
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
M10 Washer (29)
M8 Washer (41)
M6 x 16mm Screw (10)
M8 x 16mm Bolt (44)
M10 Spacer (42)
M6 Washer (31)
M10 Nylon Locknut (45)
M8 Nylon Locknut (43)
M6 x 50mm Screw (38)
M8 x 55mm Bolt (22)
M10 x 168mm Bolt (40)
M6 x 38mm Screw (14)
M8 x 35mm Carriage Bolt (36) M8 x 68mm Bolt (28)
M10 x 55mm Bolt (49)
M10 x 67mm Bolt (46)
Page 19
PART LIST—Model No. WEBE08920 R0702B
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
1 1 Bench Frame
2 1 Front Leg
3 1 Left Base
4 1 Left Upright
5 1 Right Upright
6 2 Weight Rest
7 1 Right Base
8 2 50mm x 45mm Outer Bushing
9 1 Leg Lever
10 4 M6 x 16mm Screw
11 1 Lat Tower
12 1 Weight Carriage
13 1 Curl Post
14 4 M6 x 38mm Screw
15 1 Backrest
16 1 Seat
17 1 Curl Pad
18 1 Lat Bar
19 2 Handgrip
20 2 Backrest Tube
21 4 25mm Round Inner Cap
22 2 M8 x 55mm Bolt
23 2 45mm x 38mm Outer Bushing
24 2 25mm x 50mm Inner Cap
25 1 Cable
26 1 Pulley
27 2 54mm Adjustment Knob
28 2 M8 x 68mm Bolt
29 4 M10 Washer
30 1 Storage Tube
31 5 M6 Washer
32 4 38mm Square Inner Cap
33 6 Foam Pad
34 1 44mm Adjustment Knob
35 1 Cable Clip
36 8 M8 x 35mm Carriage Bolt
37 1 Adjustment Tube
38 1 M6 x 50mm Screw
39 6 25mm Square Inner Cap
40 1 M10 x 168mm Bolt
41 2 M8 Washer
42 2 M10 Spacer
43 13 M8 Nylon Locknut
44 1 M8 x 16mm Bolt
45 3 M10 Nylon Locknut
46 1 M10 x 67mm Bolt
47 6 19mm Round Inner Cap
48 3 Pad Tube
49 1 M10 x 55mm Bolt
50 2 Weight Clip
# 1 User’s Manual
# 1 Exercise Guide
Key No. Qty. Description Key No. Qty. Description
Page 20
EXPLODED DRAWING—Model No. WEBE08920 R0702B
25
43
21
33
42
26
45
25
35
32
29
32
23
21
11
44
12
23
42
34
9
32
49
29
21
33
47
45
41
43
21
47
48
13
48
41
7
47
17
36
46
2
47
10
43
47
39
19
18
6
16
8
27
30
5
45
28
36
29
43
24
32
14
39
20
29
43
36
50
48
43
10
33
36
47
22
22
43
43
1
31
38
10
33
43
15
40
19
14
37
31
3131
14
3
39
6
27
8
39
39
4
43
43
24
36
Loading...