R Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne p as retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
GHT 180 LE
GHT 220 LE
ENGLISH ESPAÑOL
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
A VERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
CopyrightE2002 Electrolux Home Products, Inc.
530086334 4/23/02
FRANÇAIS
SAFETY RULES
WARNING:
Safety Rules and Precautions can result in
serious injury.
DANGER:
BE DANGEROUS!
injury including amputation or blindness to the
operator and others. The warnings and safety
instructions in this manual must be followed to
provide reasonable safety and efficiency in using this unit. The operator is responsible for following the w ar nings and instructions in this
manual and on the unit. Never allow children to
use this tool.
KNOW YOUR UNIT
Read your instruction manual carefully until
S
you completely understand and can follow
all warnings and safety rules before operating the unit.
D
Restrict unit to users who understand and
will follow all warnings and safety rules in
this manual and on the unit.
PLAN AHEAD
WARNING:
ing unit. Remove all debris and hard objects
such as rocks, glass, wire, etc. that can ricochet, be thrown, or otherwise cause injury or
damage during operation.
D
Always wear eye protection when operating,
servicing, or performing maintenance on unit.
Wearing eye protection will help to prevent
brush or debris from being thrown or ricocheting into eyes and face which can result in
blindness and/or serious injury . Eye protection should be marked Z87.
D
Wear hearing protection when using this
unit.
D
Secure hair above shoulder length. Secure
or remove jewelry, loose clothing, or clothing with loosely hanging straps, ties, tassels, etc. They can be caught in moving
parts.
D
Stay alert. Do not operate unit when you are
tired, ill, upset, or if you are under the influence
of alcohol, drugs, or medication.
D
Keep children, bystanders, and animals
away from work area a minimum of 30 feet
(10 m) when starting or operating unit.
HANDLE FUEL WITH CAUTION
D
Eliminate all sources of sparks or flame (including smoking, open flames, or work that
can cause sparks) in the areas where fuel is
mixed, poured, or stored.
D
Mix and pour fuel in an outdoor area; store
fuel in a cool, dry, well ventilated place; use
an approved, marked container for all fuel
purposes.
D
Do not smoke while handling fuel or while
operating the unit.
D
Do not fill fuel tank while engine is running.
D
Make sure the unit is properly assembled
and in good operating condition.
Failure to follow all
THIS POWER TOOL CAN
This unit can cause serious
Inspect area before start-
-- 2 --
D
Avoid spilling fuel or oil. Wipe up fuel spills
before starting the engine.
D
Move at least 10 feet (3 meters) away from
fuel and fueling site before starting engine.
D
Always store gasoline in a container approved for flammable liquids.
OPERATE YOUR UNIT SAFELY
DANGER:
HANDS AWAY FROM BLADE
moves momentarily after the trigger is released. Do not attempt to clear away cut material when the blade is in motion. Make sure
the switch is in the OFF position, the spark
plug wire is disconnected, and the blade has
stopped moving before removing jammed
material from the cutting blade. Do not grab or
hold the unit by the cutting blade.
D
Inspect unit before each use for worn,
loose, missing, or damaged parts. Do not
use until unit is in proper working order.
D
Keep outside surfaces free from oil and
fuel.
D
Never start or run engine inside a closed
room or building. Breathing exhaust fumes
can kill.
D
Avoid dangerous environments. Do not use
in unventilated areas or where explosive
vapors or carbon monoxide build up could
be present.
D
Do not overreach or use from unstable surfaces such as ladders, trees, steep slopes,
rooftops, etc. Keep firm footing and balance
at all times.
D
Do not raise unit above your shoulders; the
cutting blade can come dangerously close
to your body.
D
Always keep unit in front of your body. Keep
all parts of your body away from the cutting
blade.
D
Keep the cutting blade and air vents free
from debris.
D
Use only for jobs explained in this manual.
RISK OF CUT; KEEP
--Blade
MAINTAIN YOUR UNIT PROPERLY
D
Have all maintenance other than the recommended procedures described in the instruction manual performed by an authorized service dealer.
D
Disconnect spark plug before performing
maintenance except for carburetor adjustments.
D
Do not use a cutting blade that is bent,
warped, cracked, broken, or damaged in
any other way. Have worn or damaged
parts replaced by an authorized service
dealer.
D
Use only recommended Weed Eater!cutting blades and replacement parts; use of
any other parts may void your warranty and
cause damage to your unit.
D
Empty fuel tank before storing the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops.
D
Hand carry the unit with the engine stopped
and the muffler and cutting blade away from
your body.
D
Allow engine to cool, empty the fuel tank,
and secure the unit before storing or transporting it in a vehicle.
Safety
Glasses
D
Do not store the unit or fuel in a closed area
Boots
30 ft.
(10 m)
Blades move
momentarily
after the
trigger is
released.
Allow blades to stop
before removing
them from the cut.
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D
Store the unit so the cutting blade cannot
accidentally cause injury.
D
Store in a dry area out of reach of children.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel damage in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condition of this tool.
WARNING:
Blades can throw objects violently.
D
You can be blinded or injured.
D
Wear safety glasses.
WARNING:
Hazard zone for thrown objects
D
Blades can throw objects violently.
D
Others can be blinded or injured.
D
Keep people and animals 30 feet
(10 m) away.
WARNING:
Blades move momentarily after the
trigger is released.
D
The blades can seriously cut you or
others.
D
Allow blades to stop before
removing them from the cut.
SPECIAL NOTICE:
with a temperature limiting muffler and spark
arresting screen which meets the requirements of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in alocale where such regulations exist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arresting screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an authorized service dealer.
This unit is equipped
ASSEMBLY
NOTE:
in the empty fuel tank.
ASSEMBLY
Your hedge trimmer is fully assembled; no assembly is required.
It is normal for the fuel filter to rattle
-- 3 --
OPERATION
KNOW YOUR HEDGE TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.
Muffler
Spark Plug
Hand Guard
Primer Bulb
ON/OFF SWITCH
The ON/OFF SWITCH is used to stop the engine. To stop engine, move switch to OFF.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving choke lever to the desired position. See
STARTING YOUR ENG INE for comple testarting information.
WARNING:
and after use. Do not touch the muffler or allow combustible material such as dry grass or
fuel to do so.
Muffler is very hot during
BEFORE STARTING ENGINE
WARNING:
information in the safety rules before you begin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-235-5878.
Be sure to read the fuel
FUELING ENGINE
WARNING:
when refueling.
This engine is certified to operate on unleaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/Weed Eater
brand synthetic oil is recommended. (A 40:1
ratio is obtained by mixing 3.2 ounces of oil
with 1 gallon of unleaded gasoline). DO NOT
USE automotive oil or boat oil. These oils will
cause engine damage. When mixing fuel, follow instructions printed on oil container. Once
oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly
mixed. Always read and follow the safety
rules listed under HANDLE FUEL WITH
CAUTION.
Remove fuel cap slowly
-- 4 --
ON/OFF
Switch
Throttle Lock
Throttle
Lock--out
Throttle
Trigger
Choke Lever
Fuel Mix Fill Cap
PRIMER BULB
The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original position.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed. Squeeze the trigger for full speed operation; release it for idle speed.
IMPORTANT
Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separation
and formation of acids during storage. Acidic
gas can damage the fuel system of an engine
while in storage. To avoid engine problems,
empty the fuel system before storage for 30
days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season.
Never use engine or carburetor cleaner products in the fuel tank or permanent damage
may occur.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 30 seconds at full
throttle. Releasing the trigger and allowing
the engine to briefly return to idle speed (5 -10 seconds) will be sufficient.
IMPORTANT POINTS
Use the minimum throttle speed necessary
S
to effectively cut hedges for optimal hedge
trimmer performance.
Never attempt to use this hedge trimmer to
S
cut hedges that have any branches with a
diameter larger than 7/16".
OPERATING POSITION
Hearing
Protection
Eye
Protection
STOPPING YOUR ENGINE
D
To stop the engine, move the ON/OFF
switch to the OFF position.
STARTING YOUR ENGINE
D
Fuel engine. Move at least 10 feet (3 meters) away from the fueling site.
D
Hold the unit on the ground in the starting
position as shown. Support unit so the
blade is off of the ground and away from
trees, bushes, onlookers, etc.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
Throttle Lock
Throttle
Lock-out
Throttle
Trigger
1. Move the ON/OFF switch to the ON posi-
tion.
2. Engage the throttle lock as follows:
D
press the throttle lock--out;
D
squeeze and hold throttle trigger;
D
press and hold throttle lock, then
D
release the throttle trigger
NOTE:
the engine starts.
Keep the throttle lock engaged until
ON
OFF
Switch
3. Slowly press the primer bulb 6 times.
4. Move the choke lever to the FULL CHOKE
position.
Primer Bulb
5. Pull starter rope handle sharply until engine sounds as if it is trying to run, but do
not pull rope more than 6 times.
6. Move the choke lever to the HALF
CHOKE position.
7. Pull starter rope sharply until the engine
runs, but no more than 6 pulls.
If the engine doesn’t start after 6 pulls
NOTE:
(at the HALF CHOKE position), check to
make sure the ON/OFF switch is in the ON
position. Move the choke lever to the FULL
CHOKE position and press the primer bulb 6
times; pull the starter rope 2 more times.
Move the choke lever to the HALF CHOKE
position and pull the starter rope until the engine runs, but no more than 6 more pulls. If
the engine still doesn’t start, it is probably
flooded. Proceed to STARTING A
FLOODED ENGINE.
8. Once the engine starts, allow the engine to
run 10 seconds, then move the choke lever
to the OFF CHOKEposition. Allow the unit to
run for 30 more seconds at the OFF CHO KE
position before squeezing and releasing the
throttle trigger to release the throttle lock.
NOTE:
If engine dies with the choke lever in
the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the
rope until the engine runs, but no more than 6
pulls.
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Slowly press the primer bulb 6 times.
3. Move the choke lever to the HALF
CHOKE position.
4. Engage the throttle lock as directed in
STARTING A COLD ENGINE.
NOTE:
Keep the throttle lock engaged until
the engine starts.
5. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
6. Allow the engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position.
7. Release the throttle lock by squeezing and
releasing the trigger.
NOTE:
rope 5 more pulls. If engine still does not run, it
is probably flooded. Proceed to STARTING A
FLOODED ENGINE.
If engine has not started, pull starter
-- 5 --
Choke
Lever
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the ON/OFF switch in the ONposition and the
choke lever in the OFF CHOKE position and
engaging the throttle lock as directed in the
STARTING A COLD ENGINE section; then,
pull the rope to clear the engine of excess
fuel. Starting could require pulling the starter
rope many times depending on how badly the
unit is flooded. If the unit still doesn’t start, refer
to the TROUBLESHOOTING TABL E or call
1-800-554-6723.
SERVICE
WARNING:
is in the OFF position and disconnect the
spark plug before performing maintenance
except for carburetor adjustments.
We recommend all service and adjustments
not listed in this manual be performed by an
authorized service dealer.
CLEAN AIR FILTER
Cleaning the air filter:
A dirty air filter decreases engine performance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
Clean the cover and the area around it to
S
keep debris from falling into the carburetor
chamber when the cover is removed.
Remove parts as illustrated.
S
NOTE:
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emissions.
S
S
S
S
Do not clean filter in gasoline or other
Wash the filter in soap and water.
Allow filter to dry.
Add a few drops of oil to the filter; squeeze
filter to distribute oil.
Replace parts.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
Ensure ON/OFF switch
Air Filter
Cover
Air Filter
Screw
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recommend that your muffler be serviced or replaced by an authorized service dealer.
CARBURETOR ADJUSTMENT
Your carburetor is equipped with limiter caps.
Damage will occur if you turn the needles beyond the limiter caps. Carburetor adjustment is
a complicated task. We recommend that you
take your unit to an authorized service dealer.
IGNITION TIMING
Ignition timing is fixed, non-adjustable.
SPARK PLUG
Replace spark plug yearly with a Champion
RCJ-7Y plug. Spark plug gap is 0.025 inch.
STORAGE
WARNING:
steps after each use:
Allow engine to cool, and secure the unit
S
before storing or transporting.
Store unit and fuel in a well ventilated area
S
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
Store unit with all guards in place. Position
S
unit so that any sharp object cannot accidentally cause injury.
Store unit and fuel well out of the reach of
S
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
Clean the entire unit.
S
Store in a clean dry area.
S
Clean all parts and check for damage.
S
Have damaged parts repaired or replaced
by an authorized service dealer.
Keep all nuts, bolts, and screws tight.
S
Lightly oil external metal surfaces, includ-
S
ing the blade.
To oil the blade, do the following:
Stop the engine and allow blade to come to
S
a complete stop.
Ensure ON/OFF switch is in the OFF posi-
S
tion.
Disconnect the spark plug wire.
S
Apply a light machine oil along the edge of
S
the top strap as shown.
Perform the following
OIL
WARNING:
uct contains chemicals known to the State of
California to cause cancer.
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire hazard or affecting engine performance.
The muffler on this prod-
-- 6 --
Top S t r a p
TROUBLESHOOTING TABLE
WARNING:
recommended remedies below other than remedies that require operation of the unit.
Always stop unit and disconnect spark plug before performing any of the
TROUBLE CAUSE REMEDY
Engine will not
start.
Engine will not
idle properly.
Engine will not
accelerate, lacks
power , or dies
under a load.
Engine
smokes
excessively.
Engine
runs hot.
NEED ASSISTANCE?
NEED ASSISTANCE?
Call 1-800-554-6723 for assistance.
NEED SERVICE PARTS?
Contact your dealer.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaser that each new
Weed Eater brand gasoline tool or attachment
is free from defects in material and workmanship and agrees to repair or replace under this
warranty any defective gasoline product or attachment as follows from the original date of
purchase.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS - - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTRO LUX HOME
Engine flooded.
S
Fuel tank empty.
S
Spark plug not firing.
S
Fuel not reaching carburetor .
S
Compression low.
S
Carburetor requires adjustment.
S
Crankshaft seals worn.
S
Compression low.
S
Air filter dirty.
S
Spark plug fouled.
S
Carburetor requires adjustment.
S
Carbon build up.
S
Compression low.
S
Choke partially on.
S
Fuel mixture incorrect.
S
Air filter dirty.
S
Carburetor requires adjustment.
S
Fuel mixture incorrect.
S
Spark plug incorrect.
S
Carburetor requires adjustment.
S
Carbon build up.
S
See “Starting Instructions.”
S
Fill tank with correct fuel mixture.
S
Install new spark plug.
S
Check for dirty fuel filter; replace.
S
Check for kinked or split fuel line;
repair or replace.
Contact an authorized service dealer.
S
See “Carburetor Adjustments.”
S
Contact an authorized service dealer.
S
Contact an authorized service dealer.
S
Clean or replace air filter.
S
Clean or replace spark plug; re-gap.
S
See “Carburetor Adjustments.”
S
Contact an authorized service dealer.
S
Contact an authorized service dealer.
S
Adjust choke.
S
Empty fuel tank and refill with
S
correct fuel mixture.
Clean or replace air filter.
S
See “Carburetor Adjustments.”
S
See “Fueling.”
S
Replace with correct spark plug.
S
See “Carburetor Adjustments.”
S
Contact an authorized service dealer.
S
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune--ups, spark
plugs, filters, starter ropes, starter springs, cutting line, or rotating head parts that will wear and
require replacement with reasonable use during
the warranty period. This warranty does not
cover predelivery setup or normal adjustments
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN.SOME
STATESDO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY
LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL ORCONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
The policy of ELECTROLUX HOME PRO-
DUCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, designs, specifications, and accessories of all
products at any time without notice or obligation
to any purchaser.
-- 7 --
U.S. EPA/CALIFORNIA
EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Environmental Protection
Agency/California Air Resources Board and
POULAN/W EED EATER, DIVISION OF WCI
OUTDOOR PRODUCTS are pleased to ex-
plain the emissions control system warranty on
your year 2000--2003 small off-- road engine. In
California, all new small off--road engines must
be designed, built, and equipped to meet the
State’s stringent anti--smog standards. POU-
LAN/WEED EATER must warrant the emission
control system on your small off--road engine for
the periods of time listed below provided there
has been no abuse, neglect, or improper maintenance of your small off--road engine engine.
Your emission control system includes parts
such as the carburetor and the ignition system.
Where a warrantable condition exists, POU-
LAN/WEED EATER will repair your small off--
road engine engine at no cost to you. Expenses
covered under warranty include diagnosis,
parts and labor. MANUFACTURER’S WAR-
RANTY COVERAGE: If any emissions related
part on your engine (as listed under Emissions
Control War r anty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced
by POULAN/WEED EATER. OWNER’S
WARRANTY RESPONSIBILITIES: As the
small off--road engine engine owner, you are responsible for the performance of the required
maintenance listed in your instruction manual.
POULAN/W EED EATER recommends that
you retain all receipts covering maintenance on
your small off--road engine, but POULAN/
WEED EA TER cannot deny warranty solely for
the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance.
As the small off--road engine engine owner , you
should be aware that POULAN /W EED EATER
may deny you warranty coverage if your small
off--road engine engine or a part of it has failed
due to abuse, neglect, improper maintenance,
unapproved modifications, or the use of parts
not made or approved by the original equipment
manufacturer. You are responsible for presenting your small off--road engine to a POULAN/
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount of
time, not to exceed 30 days. If you have any
questions regardingyour warranty rights and responsibilities, you should contact your nearest
authorized service center or call POULAN/
WEED EATER at 1--800--554--6723.
WARRANTY COMMENCEMENT DATE: The
warranty period begins on the date the small
off--road engine is purchased. LENGTH OF
COVERAGE: This warranty shall be for a period of two years from the initial date of purchase.
WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replace-
ment of any warranted part will be performed at
no charge to the owner at an approved POU-
LAN/WEED EATER servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
POULAN/W EED EATER at 1--800--554--6723
WARRANTY PERIOD: Any warranted part
which is not scheduled for replacement as required maintenance, or which is scheduled only
for regular inspection to the effect of “repair or
replace as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
for replacement as required maintenance shall
be warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be charged
for diagnostic labor which leads to the determination that a warranted part is defective if the
diagnostic work is performed at an approved
POULAN/W EED EATER servicing center.
CONSEQUENTIAL DAMAGES: POUL AN/
WEED EATER may be liable for damages to
other engine components caused by the failure
of a warranted part still under warranty. WHAT
IS NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD--ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty claim.
POULAN/W EED EATER is not liable to cover
failures of warranted parts caused by the use of
add--on or modified parts. HOW TO FILE A
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call POULAN/WEED EATER at
1--800--554--6723. W HERE TO GET WAR-
RANTY SERVICE: Warranty services or repairs shall be provided at all POULAN/WEED
EATER service centers. call: 1--800--554--6723
MAINTENANCE, REPLACEMENT AND REPA IR OF EMISSION RELATED PARTS:Any
POULAN/W EED EATER approved replace-
ment part used in the performance of any warranty maintenance or repair on emission related
parts will be provided without charge to the owner if the part is under warranty. EMISSION
CONTROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered
up to maintenance schedule), Ignition Module,
Muffler including catalyst. MAINTENANCE
STATEMENT: The owner is responsible for the
performance of all required maintenance as defined in the instruction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 8 --
Loading...