Weed Eater GE1138 User Manual

REPAIR PARTS MANUAL
MODEL NO. GE1138 (SN1138A) Lawn Tractor
®
182360 1.16.02 TR
PRINTED IN U.S.A.
HOW TO USE THIS MANUAL
Each tractor has its own model number.
The model number for your tractor can be found on the fender under the seat.
When ordering parts, always give the following information:
• Product - “Lawn Tractor”
• Model Number - GE1138 (SN1138A)
• Part Number
• Part Description
TABLE OF CONTENTS
SCHEMATIC.............................................................................................................. 3
ELECTRICAL......................................................................................................... 4-5
CHASSIS AND ENCLOSURES ............................................................................ 6-7
DRIVE ..................................................................................................................... 8-9
STEERING WHEEL ...........................................................................................10-11
SEAT ........................................................................................................................ 12
DECALS .................................................................................................................. 13
ENGINE ................................................................................................................... 14
MOWER LIFT .......................................................................................................... 15
MOWER DECK .................................................................................................. 16-17
WARRANTY............................................................................................................ 19
2
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

SCHEMATIC

A
AMMETER
(OPTIONAL)
RED
B
G
IGNITION
SWITCH
BLACK
RED
BLACK
BATTERY
RED
FUSE
WHITE
RED
M
STARTER
BLACK
SOLENOID
S
M
L
CLUTCH / BRAKE
(PEDAL UP)
WHITE
SEAT SWITCH
(NOT OCCUPIED)
WHITE
BLACK
BLACK
HOUR
ATT'MENT CLUTCH
BLACK
(CLUTCH OFF)
BLACK
BLACK
GROUNDING
CONNECTOR
METER
BLUE
(OPTIONAL)
FUEL LINE
BLACK
IGNITION
UNIT
TWIN CYL. ENGINES)
SPARK
PLUG
GAP
(2 PLUGS ON
S
M
B
L
IGNITION SWITCH
CIRCUITPOSITION
OFF
M + G
B + LON
B + S + LSTART
CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM
FUEL SHUT-OFF SOLENOID
(IF SO EQUIPPED)
RED
LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM
WIRING INSULATED CLIPS
G
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR
28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED)
DIODE
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)
ALTERNATOR
NON-REMOVABLE
CONNECTIONS
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.
REMOVABLE
CONNECTIONS
3
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
ELECTRICAL
42
24
41
33
30
27
43
27
25
27
27
26
40
16
16
48
8
27
2
1
52
29
28
90
4
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
ELECTRICAL
KEY PART NO. NO. DESCRIPTION
1 163465 Battery 2 74760412 Bolt Hex Hd 1/4-20unc X 3/4 8 176689 Box Battery Fender 16 176138 Switch Interlock 24 4799J Cable Battery 25 146147 Cable Battery 6 Ga 44" red 26 175158 Fuse 20 AMP 27 73510400 Nut Keps Hex 1/4-20 Unc 28 4207J Cable Ground 6 Ga 12" black 29 121305X Switch Plunger Nc Gray 30 175567 Switch Ign 33 140401 Key Ign 40 179730 Harness Ignition 41 71110408 Bolt Blk Fin Hex 1/4 - 20 x 1/2 42 131563 Cover Terminal Red 43 178861 Solenoid 48 140844 Adapter Ammeter 52 141940 Protection Wire Loop 90 180449 Cover Terminal Battery
NOTE: All component dimensions give in U.S. inches
1 inch = 25.4 mm.
5
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
CHASSIS AND ENCLOSURES
212
208
26
30
25
31
17
24
29
18
24
25
26
3
11
209
9
15
209
5
5
209
58
53
12
51
28
52
55
57
33
206
26
8
209
6
16
3
35
37
10
2
38
3
205
35
38
3
34
26
205
1
145
37
54
13
208
6
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
CHASSIS AND ENCLOSURES
KEY PART NO. NO. DESCRIPTION
1 174620 Chassis 2 176554 Drawbar 3 17060612 Screw, 3/8-16 x 3/4 SMGML Tap/R 5 155272 Bumper Hood/Dash 6 174643X012 Saddle Flat 8 155138 Clip Retainer Slide-On 9 168347X011 Dash P/L 10 72140608 Bolt, Rdhd Sqnk 3/8-16 x 1 11 174996 Panel Asm.Dash LH 12 145660 Clip Tinnerman Grille P/L 13 172105X010 Dash, Panel RH 15 74180512 Screw Mach.Trhd 5/16-18 UNC x 3/4 16 73510500 Nut Keps 5/16-18 UNC 17 159639X550 Hood Pnt Stl PL 18 126938X Bumper Hood 24 74780616 Bolt, Hex , Fin. 3/8-16UNC x 1 Gr. 5 25 19131312 Washer 13/32 x 13/16 x12 Gauge 26 73800600 Nut Lock Hex w/Ins. 3/8-16 Unc 28 179780 Grille/Lens Asm. 29 150209X428 Lens Grille 30 169465X550 Fender Pnt 31 136619 Bracket Fender 33 179716X550 Footrest Pnt., LH 34 179717X550 Footrest Pnt., RH 35 72110606 Bolt Rdhd Sht. Sqnk 3/8-16 X 3/4 37 17490508 Screw Thdrol 5/16-18 x 1/2 Tyt 38 175710 Bracket Asm Pivot Mower Rear 51 73800400 Nut Lock Hex W/Ins 1/4-20 52 19091416 Washer 9/32 x 7/8 x 16 Ga. 53 144697 Bracket, Grille LH 54 161464 Screw Hex WSHD 8-18 x 7/8 55 144696 Bracket Grille RH 57 74780412 Bolt Fin Hex 1/4-20 x 3/4 58 150127 Duct Air Engine 145 156524 Rod Pivot Chassis/Hood 205 17490608 Screw Thdrol 3/8-16 x 1/2 206 170165 Bolt Shoulder 5/16-18 208 17670608 Screw Thdrol 3/8-16 x 1/2 209 17000612 Screw Hex Wsh Thdrol 3/8-16 x 3/4 212 156494 Insert Lens Reflect Quarda
- - 5479J Plug Btn Blk .359 Dia Ch/Inf
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
7
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

DRIVE

10
13
14
112
52
52
21
8
250
30
4
32
11
12
57
170
51
63
212
59
7
61
12
18
113
51
5
18
6
6
32
30
52
6
56
41
38
39
66
65
64
50
27
49
47
70
116
55
202
150
48
151 51
77
15
96
119
24
78
76
62
35
29
36
37
34
28
22
3
79
1
75
250
119
19
25
2
77
74
119
27
120
36
35
53
8
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
DRIVE
KEY PART NO. NO. DESCRIPTION
1 - - - - - - - Transaxle Peerless, Model 204-
506B (Order parts from transaxle
manufacturer) 2 146682 Spring, Brake Return 3 123666X Pulley, Transaxle 4 12000028 Rin g, Ret ainer 5 121520X Str ap, To rque 6 17060512 Screw, 5/16-18 x 3/4 SMGML 7 162240 Bracket, T/A, Saddle Shift 8 131679 Rod, Shifter 10 76020416 Pin, Cotter 1/8 x 1 11 105701X Washer, Shift Plate 12 19151216 Washer 15/32 x 3/4 x 16 13 74550412 Bolt 1/4-28 UNF Gr. 8 w/Patch 14 10040400 Washer Lock 18 74780616 Bolt, Fin Hex 3/8-16 Unc x 1 Gr. 5 19 73800600 Locknut 3/8-16 21 106933X Knob 22 130804 Rod, Brake 24 73350600 Nut, Hex Jam 3/8-16 25 106888X Spring, Rod, Brake 26 19131316 Washer 13/32 x 13/16 x 16 Gauge 27 76020412 Pin, Cotter 1/8 x 3/4 28 175765 Rod, Brake, Park 29 71673 Cap, Plunger 30 174973 Bracket, Transaxle, L.H. 32 74760512 Bolt Hex Hd 5/16-18 UNC x 3/4 34 175578 Shaft, Foot Pedal 35 120183X Bearing Nylon 36 19211616 Washer 21/32 x 1 x 16 Gauge 37 1572H Pin,Roll 3/16 x 1 38 179114 Pulley, Idler 39 74760648 Bolt, RDHD 3/8-16unc x 3 Gr. 5 41 175556 Keeper, Belt 47 127783 Pulley, Idler 48 154407 Bellcrank Asm Clutch 49 123205X Retainer, Belt
KEY PART NO. NO. DESCRIPTION
50 74760624 Bolt, Hex 3/8-16 x 1-1/2 51 73680600 Nut, Crownlock 3/8-16 52 73680500 Nut, Crownlock 5/16-18 53 105710X Link, Clutch 55 105709X Spring, Return, Clutch 56 17060620 Screw 3/8-16 x 1-1/4 57 130801 V-Belt, Drive 59 169691 Keeper Belt Center Span 61 17120614 Screw 3/8-16 x .875 62 8883R Cover, Foot Pedal 63 180219 Pulley, Engine 64 71170764 Bolt, Hex 7/16-20 x 4 Gr. 5 65 10040700 Washer, Lock Hvy Hlcl Spr 7/16 66 154778 Keeper, Belt Engine F-Proof 70 180218 Guide Belt Mower Drive RH 74 137057 Spacer, Split 75 121749X Washer 25/32 x 1-1/4 x 16 Ga. 76 12000001 E-Ring 77 123583X Key Square 78 121748X Washer 25/32 x 1-5/8 x 16 Ga. 79 2228M Key Woodruff #9 3/16 x 3/4 96 4497H Retainer Spring 1" Ziinc/Cad 112 19091210 Washer 9/32 x 3/4 x 10 Ga. 113 127285X Strap Torque L.H. Lt 116 72140608 Bolt, RdHd Sq Neck 3/8-16 x 1 120 73900600 Nut Lock Flg 3/8-16 145 74490540 Bolt, Hex Flghd 5/16-18 Gr. 5 150 175456 Spacer Retainer 151 19133210 Washer 13/32 x 2 x 10 Ga. 170 178394 Keeper, Belt, Transaxle 202 72110614 Bolt Carr Sh 3/8-16 x 1-3/4 Gr. 5 212 145212 Nut Hex Flange Lock 250 17060612 Screw, 3/8-16 x 3/4 SMGML
NOTE: All component dimensions give in U.S. inches.
1 inch = 25.4 mm.
9
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
STEERING WHEEL
38
63
11
39
1
41
42
37
37
36
44
51
91
43
29
68
29
15
15
54
88
71
29
17
82
29
15
46
8
6
9
2
7
9
5
3
40
47
65
85
11
10
68
13
46
8
85
32
26
28
30
6
67
67
67
9
47
7
9
5
4
43
43
6
8
10
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
STEERING WHEEL
KEY PART NO. NO. DESCRIPTION
1 133741X428 Wheel Steering 2 175131 Axle Asm Front 3 169840 Spindle Asm LH 4 169839 Spindle Asm RH 5 6266H Bearing, Race, Thrust Hardened 6 121748X Washer 25/32 X 1-5/8 X 16 Ga 7 19272016 Washer 27/32 X 1-1/4 X 16 Ga 8 12000029 Ring Klip 9 3366R Bearing 10 175121 Link Drag 11 10040600 Washer Lock Hvy Hlcl Spr 3/8 13 163518 Spacer Brg. Axle Front 15 145212 Nut Hexflange Lock 17 177876 Shaft Asm 26 126847X Bushing Link Drag Blk Lr 28 19131416 Washer 13/32 x 7/8 x 16 Ga. 29 17060612 Screw 3/8-16x3/4 SMGML Tap/R 30 76020412 Pin Cotter 1/8 x 3/4 CAD 32 130465 Rod Connecting 36 155099 Bushing Steering 37 152927 Screw TT #10-32 X 5 x 3/8 Flange 38 133742X428 Cap Wheel Steering 39 19133812 Washer 13/32 x 2-3/8 x 12 Ga 40 7810H Nut Lock Center 3/8-24 Unf 41 100711L Adapter Wheel Strg 42 145054X428 Boot Steering 43 121749X Washer 25/32 X 1 1/4 X 16 Ga 44 153720 Extension Steering 46 121232X Cap Spindle 47 6855M Fitting Grease 51 73800500 Nut Lock Hex W/Ins. 5/16-18 Unc P 54 74780520 Bolt Fin Hex 5/16-18 Unc 6 x 1-1/4 63 74780616 Bolt Fin Hex 3/8-16unc x 1 Gr. 5 65 160367 Spacer Brace Axle 67 72140618 Bolt RDHD SQ 3/8-16UNC x 2-1/4 68 169827 Brace Axle 71 175146 Steering Asm 82 169835 Bracket Susp. Chassis Front 85 133835 Fastener Christmas Tree 88 175118 Bolt Shoulder 7/16-20unc 91 175553 Cl ip St eering
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm
11
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

SEAT

1
8
8
9
7
5
14
9
7
10
6
22
24
26
16
25
15
23
13
17
KEY PART NO. NO. DESCRIPTION
1 175389 Seat 2 140551 Bracket, Pivot, Seat 3 71110616 Fin Hex 3/8-16unc x 1 4 19131610 Washer 13/32 x 1 x 10 Ga. 5 145006 Clip, Push-in 6 73800600 Nut 7 124181X Spring, Seat 8 17000616 Screw, 3/8-16 x 1.5 SMGML Tap/R 9 19131614 Washer 13/32 x 1 x 14 Ga. 10 174894 Pan, Seat 12 121246X Bracket, Mounting, Switch, Seat 13 121248X Bushing, Nylon
12
2
5
4
3
KEY PART NO. NO. DESCRIPTION
14 72050412 Nut, Crownlock 1/4-20 x 1-3/8 15 134300 Spacer, Split 16 121250X Spring 17 123976X Nut, Lock, Flange 1/4 Gr. 5 21 171852 Bolt, Shoulder 5/16-18 UNC-2A 22 73800500 Nut 23 71110814 Bolt Hex Black 24 19171912 Washer 17/32 x 1-3/16 x 12 Ga. 25 127018X Bolt Shoulder 5/16-18 x .62 26 10040800 Washer Lock Hvy Hclc Spr 1/2
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
21
12
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

DECALS

3
13
2
6
9
15
KEY PART NO. NO. DESCRIPTION
1 145498 Decal, Instruction, Operation 2 171448 Decal, Fender 3 163447 Decal, Hood R.H. 4 163448 Decal Hood. L.H. 5 182446 Decal 6 159736 Decal, Chassis Hot Muffler 7 159737 Decal, Brake/Clutch Symbol LT 9 181650 Decal, HP Engine 11 145494 Decal, Mower Cutfinger Symbol 12 180432 Decal 100 DBA
5
5
11
KEY PART NO. NO. DESCRIPTION
13 137042 Decal, Wheel Steering 14 145005 Decal, Btry Dngr/Psn P/L Sym 15 136832 Decal, V-Belt 16 162391 Decal, Deck 19 140837 Decal, Parking Brake
- - 138311 Decal, Handle, Lift, Height Adjust
- - 162598 Decal, Drawbar Load Limit
- - 182359 Manual, (Euro) Operator's
- - 182360 Manual, Repair Parts
4
6
12
7
16
(Lift Handle)
19
14
1
TIRES AND WHEELS
1
2
6
5,8
7
4,10
3,9
11
KEY PART NO. NO. DESCRIPTION
1 59192 Cap, Valve 2 65139 Stem, Valve 3 124157X Tire Front 4 59904 Tube, Front (not furnished) 5 106732X427 Rim, Asm. Front 6 278H Grease Fitting (rear tire only) 7 9040H Bearing, Flange (front tire only) 8 106108X427 Rim, Asm. Rear 9 123969X Tire, Rear 10 7152J Tube, Rear (not furnished) 11 104757X428 Cap, Axle
- - 144334 Sealant, Tire (10 oz. Tube)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
13
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

ENGINE

2
32
3
72
78
62
13
4
1
25
26
78
38
16
44
46
33
81
14
31
40
29
37
33
OPTIONAL EQUIPMENT
Spark Arrester
KEY PART NO. NO. DESCRIPTION
1 170551 Control Th/ch 2 17720408 Screw Hex Thd Cut 1/4-20 x 1/2 3 - - - - - - Engine, Briggs & Stratton 289707
Order parts from engine manufacturer 4 137348 Muffler Exhaust 13 165291 Gasket Muffler 14 148456 Tube Drain Oil Easy 16 11050600 Washer Lock Ext Tooth 3/8 23 169837 Shield BRN/DBR Guard 25 180945 Control Choke 26 73920600 Nut Keps 3/8-24 Unf 29 137180 Kit Spark Arrestor (Flat Scrn) 31 109202X Tank Fuel Front 32 140527 Cap Asm Fuel
45
23
KEY PART NO. NO. DESCRIPTION
33 123487X Clamp Hose Blk 37 137040 Line Fuel 38 148315 Plug Easy Oil Drain 40 124028X Bushing Snap Nyl Blk Fuel Line 44 17670412 Screw Hexwsh Thdrol 1/4-20x3/4 45 17000612 Screw Hex Wsh Thdrol 3/8-16 46 19091416 Washer 9/32 X 7/8 X 16 Ga 62 10040500 Washer 5/16 72 71070512 Screw Hex Hd Cap 5/16-18 x 3/4 78 17060620 Screw 3/8-16x1-1/4 SMGML Tap/R 81 73510400 Nut Keps Hex 1/4-20 UNC
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm.
14
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

MOWER LIFT

5
7
8
13
13
11
19
31 32
31 32
13
12
3
4
2
1
6
6
5
4
13
18
20
19
20
15
20
20
16
17
15
KEY PART NO. NO. DESCRIPTION
1 159460 Wire Asm. Inner/Sprg w/Plunger 2 159471 Shaft, Asm., Lift R/H 3 105767X Pin, Groove 4 12000002 Ring, E #5133-62 5 19211621 Washer 21/32 x 1 x 21 Ga. 6 120183X Bearing, Nylon 7 109413X Grip Handle Bicycle Matte Blk 8 124526X But ton, Plunger 11 139865 Link, Lift, Lh 12 139866 Link, Lift, Rh 13 4939M Spr ing, R etaine r
KEY PART NO. NO. DESCRIPTION
15 173288 Link, Front 16 73350800 Nut, Jam, Hex 1/2-13 Unc 17 175689 Trunnion 18 73800800 Nut, Lock w/Wsh 1/2-13 Unc 19 139868 Arm, Suspension, Rear 20 163552 Spring , Retainer Zinc 31 169865 Bearing, Pvt Lft 32 73540600 Nut Crownlock 3/8-24
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
15
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00

MOWER DECK

152
151
158
21
1
153
157
154
153
109
156
67
55
123
155
54
89
107
69
122
89
40
2
4
56
3
8
113
146
36
89
40
150
45
108
36
30
33
31
53
32
148
68
2
110
21
88
87
26
28
25
24
96
97
21
2
2
86
16
3
2
15
29
14
21
23
5
6
4
19
21
149
13
11
10
27
9 8
16
REPAIR PARTS
TRACTOR - MODEL NO. GE1138 (SN1138A), PRODUCT NO. 964 77 54-00
MOWER DECK
KEY PART NO. NO. DESCRIPTION
1 170280 Deck Asm Weldment 2 72140506 Bolt 3 138017 Asm., Bar, Anti-Sway 4 169970 Bracket Sway Bar Deck 38/42" 5 4939M Spr ing, R etain er 6 178024 Bar Sway Deck 8 850857 Bolt 3/8-24 x 1.25 Gr. 8 9 10030600 Washer, Lock 10 140296 Washer, Hardened 11 138497 Blade, Mower, Hi Lift 13 137645 Asm., Shaft, Mandrel, Vented 14 128774 Housing, Mandrel, Vented 15 110485X Bearing, Ball, Mandrel 16 174493 Stripper, Mower 19 132827 Bolt, Shoulder 21 73680500 Nut, Crownlock 5/16 - 18 UNC 23 137607 Bracket, Deflector 24 105304X Cap, Sleeve 25 123713X Spring, Torsion, Deflector 26 110452X Washer, Lock 27 106736X428 Deflector, Shield 28 19111016 Washer 11/32 x 5/8 x 16 Ga. 29 106735X Rod, Hinge 30 173984 Screw Hex Thdrol 31 129963 Washer, Spacer 32 153532 Pulley , Man drel 33 178342 Nut Lock 36 131494 Pulley, Idler, Flat 40 73680600 Nut, Crownlock 3/8 - 16 UNC 45 4497H Retainer Spring 1: Zinc/Cad 53 130840 Brake Assembly 54 133943 Washer, Hardened 55 133840 Arm, Idler Assembly 56 165723 Spacer, Retainer 67 106932X Knob Rd 3/8-16 Plstc Thds Blk
KEY PART NO. NO. DESCRIPTION
68 180214 V-Belt, Mower 69 76020312 Pin, Cotter 3/32 x 3/4 86 7631J Runner, LH 87 128772 Runner, RH 88 19111216 Washer 11/32 x 3/4 x 16 Ga. 89 19131612 Washer 13/32 x 1 x 12 Ga. 96 74930620 Bolt 3/8-16 x 1-1/4 97 73930600 Nut Centerlock 3/8-16 107 133502 Spacer, Retainer 108 133503 Stiffener, Idler Arm 109 74760640 Bolt, hex Head 3/8-16 x 2-1/2 110 142587 Upstop Deck Front 38" 113 17060512 Screw, 5/16-18 x 3/4 122 131289 Rod, Brake, LH 123 169971 Rod, Brake, RH 146 165891 Bolt Carriage Idler 148 169022 Spring Return Idler 149 165898 Retainer Spring Yelow Zinc 150 19091216 Washer 9/32 x 3/4 x 16 Ga. 151 169670 Bracket Clutch Cable 152 172758 Clutch Cable 38"/42" 153 169674 Washer Flat 3/8" Type B 154 169675 Spr ing R etain er 155 169671 Spring Retention Lvr Cltch Cab 156 169672 Spacer Clutch Cable 3/8" 157 169669 Rod Clutch Cable 3/8" 158 17720408 Screw Hex Thd Cut 1/4-20 x 1/2
- - 130794 Mandrel Assembly (includes Housing, Shaft and Shaft Hardware Only - Pulley Not Included)
- - 181380 Replacement Mower, Complete
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
17
SERVICE
T
E
C
U
M
S
E
H
®
POLICY
®
T
E
C
U
M
Issued January 1980 Revised January 1991
Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below,will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFEC­TIVE IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and Series 1100 angle drive and ONE YEAR for all other Peerless products. New Power Train Components incorporated in equipment used for commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to the original purchaser.
1. Alterations or Modifications of Power Train Components.
2. Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturer’s Manual.
This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of service items which are not defective shall be paid for by the original purchaser.
Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/ o Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service can only be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of requesting warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any charges for making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work is performed. The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train Components and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.
The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any of its affiliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any of its parts, other than as set forth herein.
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s) may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume for Tecumseh any other obligations or liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or limitations of Tecumseh’s warranty in any way.
H
E
S
WARRANTY
LIMITED WARRANTIES
FOR
NEW PEERLESS GEAR POWER TRAIN COMPONENTS
A. Products Warranted
B. Products And Items Not Warranted
C. Securing Warranty Service
D. Limitation of Damages and Implied Warranties
E. No Dealer Warranty
18
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1. This warranty does not apply to the engine. Please contact your nearest dealer where they will send the machine to the engine manufacturer.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such return is requested by your dealer.
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90) days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the date of the original sale. Battery must be maintained in accordance with the instructions furnished.
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of original purchase.
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard hardware and normal maintenance.
7. In case of any problem within the boundaries of this warranty, contact the nearest department store, indicate the model number, serial number and the date of purchase of your machine. This warranty does not apply to accidental damages. All implicit warranties are limited to the same time frames. Or contact:
E.M. Services 54 Rue Lambrechts 92400 Courbevoie France Telephone: (1) 46678078 Fax: (1) 46678095
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES. ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN.
19
®
Loading...