17
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Safety instructions
! DANGER
Danger caused by wrong
mounting or handling!
Wrong mounting or handling of this
unit can result in serious injuries
or death.
First read these ins- ¾
tructions and, where
appropriate, any other
instructions and information
attached to the unit!
Please observe the warnings ¾
and notes included in the instructions and attached to the
unit!
! DANGER
This symbol identifies items that
may directly result in serious injuries or death in case of non-observance or wrong handling.
! WARNING
This symbol identifies items that
may result in serious injuries or
death in case of non-observance
or wrong handling.
! CAUTION
This symbol identifies items that
may result in injuries or material
damage in case of non-observance or wrong handling.
CAUTION
This symbol identifies items that
may result in material damage in
case of non-observance or wrong
handling.
18
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Safety instructions
! DANGER
Explosion hazard!
Operating the light in rooms subject to explosion hazards can trigger an explosion.
Operate in rooms not subject to ¾
explosion hazards only!
! WARNING
Danger due to electrical shock
in case of contact!
Maintenance or repair work carried
out incorrectly may result in serious
injuries or death.
Disconnect the light from the ¾
mains before carrying out any
maintenance or repair work!
Maintenance and repair work ¾
must be carried out by a skilled
electrician only!
Only parts released by the ¾
manufacturer may be used as
spare parts!
CAUTION
Damage caused by wrong mains
voltage!
A wrong mains voltage can result in
damaging or destroying the lamp.
Operate units of protec- ¾
tion class III with safety
extra low voltage (SELV) only!
Connection only by a skilled ¾
electrician!
Before putting the light into ¾
operation, the user has to check
whether the mains voltage is
identical with the rated voltage
specified on the rating plate.
19
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Safety instructions
! WARNING
Risk of blinding!
Looking directly into the light source may cause temporarily impaired
vision and afterimages. This may
result in irritations, inconveniences,
impairments or even accidents.
Looking directly into the light ¾
source must be avoided.
Position light in such a way that ¾
looking directly into the light
source is avoided.
CAUTION
Damage caused by the incident
laser beam!
Direct or indirect incidence of a
laser beam may result in the destruction of the LED.
Use the light only outside the ¾
range of action of high-performance lasers (e.g. cutting laser,
welding laser).
20
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Description
SPOT LED 003
According to standard DIN EN 1837, an illuminance of 500 lx is required in the work area of machines. This is
often impossible to achieve using a light that is not in the immediate proximity of the tool. However, only in rare
cases is it possible to attach a light directly to the tool slide, since the restricted room available in the interior of
the machine room does not allow this.
In the ideal case, a well illuminated machining area is achieved by combining 2 or more lights:
a) Light for basic illumination of the machining area (using, for example, a Waldmann protective tube light)
b) Additionally mounted light for the immediate machining area (e.g. Waldmann machine light MCXFL 3, MCTFL
3 or MCBFL 3) or use of built-in light MCEYL 3.
The built-in light MCEYL 3 meets the requirements from the standardif the machining area is clearly defined
and no flexibility is required.
The use of light emitting diodes (LED) instead of halogen lights allows a significantly higher useful life to be
achieved. This results in fewer machine downtimes as a result of maintenance work.
A housing made of anodised aluminium and a protective borosilicate glass pane are resistant to hot and sharpedged chips. The housing is water-proof and resistant to coolants and lubricants.
The selection between several variants of different radiation characteristics makes for universal use.
21
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Designated use Abbreviations and symbols
Intended purpose:
Built-in luminaire - light for universal
use, but in particular as additional
lighting of the working area of machines and workstations.
Place of use:
Only suitable for rooms not subject
to explosion hazards.
Not for use in the range of action
of high-performance lasers.
Operating mode:
The light is designed for continuous
operation.
The manufacturer cannot be held liable for damage caused by using the unit for purposes contrary
to the designated use or by ignoring safety instructions and warnings.
Safety or warning
instructions!
Important information!
Unit corresponds to international protection class III
(Operation with savety
extra low voltage)
The light is suitable for
mounting on normally inflammable surfaces
Observe the disposal
instructions!
LED Light Emitting Diode
VDE Approval
ENEC Approval
SEV Approval
CE
Conformity mark
22
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Mounting
General
The light has been designed as
stationary light.
Both light and operating unit must
be mounted stationary.
Caution
Damage to the light caused by
improper cable layout!
If the cable is laid incorrectly, it
may be damaged due to outside
influences (e.g. hot chips).
Make sure that the cable is laid ¾
in such a way that it cannot be
damaged!
Caution
Decrease in the useful life
In the case of insufficientheat dissipation, the useful life of the light
will decrease!
Operate light only when mount- ¾
ed!
Provide a sufficiently large ¾
metallic mounting surface (>
900 cm²).
Ensure good heat transfer ¾
between light and mounting
surface!
CAUTION
Danger due to insufficient
fastening!
When mounted incorrectly, the
light may fall down.
Mount light in a stable position ¾
using suitable screws [2.2] !
When using mounting elements ¾
which have not been proposed
by the manufacturer, the user
has to verify their reliability!
Mount light on a surface suita- ¾
ble for mounting only!
Mounting by a skilled electrician ¾
only!
23
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Connection
Caution
Damage caused by wrong mains
voltage!
A wrong mains voltage can result in
damaging or destroying the light.
Lights of internation- ¾
al protection class III
must be operated only
with safety extra low voltage
(SELV)!
Connection only by a skilled ¾
electrician!
Before putting the light into ¾
operation, the user has to check
whether the supply voltage is
identical with the rated voltage
specified on the rating plate!
All wiring termination shall be ¾
in accordance with the National
Electric Code!
Note
The light is protected against polarity reversal. The function is also
guaranteed when the two lines are
interchanged.
Light with connecting cable
The light is supplied with free
strand ends for connection to
safety extra low voltage (SELV).
For connection to the supply voltage use the terminal connector
provided with the light.
For lights with accompanying
terminal strip, the outlet must correspond to the protection type of
the light and be adequately dimensioned for the terminal strip.
Light with connector
See page 24.
Note for USA
This device must be connected to
a class 2 power supply!
24
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Connection (continued)
Fig. 15
Light with connector
For lights with built-in plug, a coupling which guarantees the compliance with the protection type must
be used for connection.
Connection assignment:
MCEYL 3 S
1 (not used)
2 (not used)
3 _
4 +
C Coding mark
Note:
Use a connection cable 1 mm².
Operation
Switching ON/OFF
The light is not equipped with a
switch of its own. It is usually switched on/off via external switching
elements.
25
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Maintenance and repair
WARNING
Danger due to electrical shock
in case of contact!
Maintenance or repair work carried
out incorrectly may result in serious
injuries or death.
¾
Disconnect the light from the
mains before carrying out any
maintenance or repair work!
Maintenance and repair work
¾
must be carried out by a skilled
electrician only!
Only parts released by the
¾
manufacturer may be used as
spare parts!
Fig. 17
LED
Defective light source
The light works with light
emitting diodes (LED). The
useful life of LEDs exceeds by far
that of conventional lamps (e.g.
light bulbs). Therefore, a lamp replacement is rarely necessary.
If nevertheless one of the three
LEDs should break down, the
entire LED module [Fig. 17] must
be replaced.
26
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Care Disposal
CAUTION
Risk of damage through wrong
care!
Wrong care may destroy the unit.
Clean the transparent cover at ¾
regular intervals!
Clean the light parts only with ¾
a cloth impregnated with a
suitable household cleaning
agent!
Make sure the agents used ¾
are compatible with paints and
plastics!
CAUTION
Environmental hazard!
Wrong disposal endangers our
environment.
Return the unit at the ¾
end of its useful life to
the available recycling
systems!
27
GB Instructions For Use Machine Light MCEYL 3 S „SPOT LED 003“
Technical data
General:
Protection class III
Protection type IP 67
Operating mode:
Continuous operation
Technical safety check
according to EN 60598-1
Rating according to DIN 60825-1
and VDE 0837 Class 1 laser
Dimensions:
MCEYL 3 S
Light body
approx. Ø 99 x 50 mm
Light with connecting cable
Connecting cable
approx. 3000 mm
Light with connector
Connector M12x1
Electrical values:
Nominal voltage 24 V AC/DC
Frequency range (AC) 50/60 Hz
Power consumption approx. 10 W
Luminous values:
Light current approx. 150 lm
Light colour amber
Useful life * approx. 50,000 h
* Decrease in luminous flux
approx. 70 %
CAUTION
Risk of damage due to differences from the standard design.
If required, this series of units will
be supplemented by further variants. The technical data may therefore be subject to modifications.
Always observe the data and ¾
symbols given on the rating
plate!
Loading...