Vtech VM351-2 User Manual

Go to www.vtechphones.com

CAUTION

THIS SIDE UP

OTMUT

]

M

 



1m (3ft)

to register your product for enhanced warranty support and latest VTech product news.

VM351-2

Quick start guide

What’s in the box

VM351-2 baby monitor system

Baby’s room Living room

Connect and power on - Baby unit Install the battery Connect and power on - Parent unit

> 3ft (1m)

3ft (1m)

The default volume of your parent unit

• is level 4. If you experience high-pitched screeching noise from your baby monitor while positioning:

Make sure your baby units and parent unit

are more than 3 feet (1 meter) apart, OR Turn down the volume of your parent unit.

Status check

Once you power on your baby monitor, your parent unit displays image from baby unit , and the LI NK LED light turns on.

The ON/OFF LED light of baby unit turns on. As baby unit is not being viewed, its ON/OFF LED light flashes.

Change different views - Single CAM

Select Single CAM as your monitoring mode to view a single baby unit in full screen.

Change different views - Split

Select Split as your monitoring mode to view the images from all baby units at once.

Change different views - Patrol

Select Patrol as your monitoring mode to alternately view the image from baby units and every 10 seconds.

10s

Change different views

In Single CAM or Patrol mode, press VIEW to switch between the image of baby units and .

Press VIEW

Dim mode

With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy.

10 min inactivity

Press any buttons

Install the lens (optional)

The wide-angle lens (VM101) provided allows you to view more of your baby’s room from the parent unit screen.

If you do not use the lens at the moment, cover both sides of the lens with the lens covers provided to avoid scratches.

OTM

L



]

M







NOTES

TIP

NOTES

Sound activation

Sound-activated Screen

O

ert

attery To

Aler

lit-

Automatically turns on the parent unit screen when the baby unit being viewed detects a sound after the screen is turned off. When no sound is detected within 50 seconds, the screen is automatically turned off to save power.

Overview - Parent unit Overview - Baby unit

Antenna

Basic operation - Parent unit

Adjust speaker volume

Press + / VOL / - to adjust your parent unit speaker volume. It determines the volume of sound transmitted from your baby units.

Zoom

Press to zoom in or out.

Light indicators

Volume

Zoom

Talk to your baby unit

Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit.

Turn off the screen

Press and hold LCD ON/OFF to switch off the screen. You can still hear sound from the selected baby unit.

Microphone

POWER

TALK

MENU / SELECT

Arrow keys

VIEW / LCD ON/OFF

Use the menu

Press MENU/SELECT to enter the menu, choose a menu item, or save a setting.

While in the menu:

Press or to scroll up or down.

•

Press to select an item.

•

Press to return to the main menu or idle

• screen.

Stand

Turn off the parent unit

Press and hold POWER to power off your parent unit.

Speaker

Power jack

Battery compartment cover

Basic operation - Baby unit

Adjust speaker volume

Press + / VOL / - to adjust your baby unit speaker volume. It determines the lullaby volume and talkback volume transmitted from your parent unit.

Light sensor

Camera

Infrared LEDs

Play/Stop

Microphone

ON/OFF slide

ON/OFF light

Lullaby

Press / to play lullaby on the baby units.

Press to skip to the other lullabies.

• Press / again to stop the lullaby.

•

Skip

+ / VOL / -

Temperature sensor

Speaker

Turn off the baby unit

Slide the ON/OFF switch to OFF to power off your baby unit.

Night vision

The baby unit has infrared LEDs that allow you to see your baby at night or in a dark room. When the baby unit detects low light levels, the infrared LEDs turn on automatically. The image from this baby unitunit is in black and white, and appears on screen.

It is normal if you see a short white glare on your parent

• unit scree n as the baby unit is ad apting to the dark environment.

When the i nfrared LEDs are on, t he image i s in black

• and whit e. This is no rmal due to extern al light s ources.

Depending on the surroundings and other interfering

• factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit’s angle, or place the baby unit at a higher level to prevent glare and blurry display.

Long press

Mount the baby monitor (optional)

Check for reception strength and

• camera angle before drilling the holes.

Place the wall mount bracket on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).

If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall.

Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole.

Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit.

Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.

Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place.

The default angle of the wall mount bracket is 90 degrees. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.