Vtech VM344-2 User Manual

Go to www.vtechphones.com

> 1m (3ft)

CAUTION

]KXOTMUT

< 1m (3ft)

> 1m (3ft)

to register your product for enhanced warranty support and latest VTech product news.

VM344-2

Quick start guide

What’s in the box

VM344-2 baby monitor system

Baby’s room Living room

Connect and power on - Baby unit

1m (3ft)

Install the battery

THIS SIDE UP

Connect and power on - Parent unit

1m (3ft)

The default volume of your parent unit

• is level 4. If you experience high-pitched screeching noise from your baby monitor while positioning:

Make sure your baby units and parent unit

are more than 1 meter (3 feet) apart, OR Turn down the volume of your parent unit.

Status check

Once you power on your baby monitor, your parent unit displays image from baby unit , and the LI NK LED light turns on.

The ON/OFF LED light of baby unit turns on. As baby unit is not being viewed, its ON/OFF LED light ﬂashes.

Change different views - View

Press VIEW to switch between the image of baby units and .

Press VIEW

Change different views - Patrol

Press PATROL to alternately view the image from baby units and every 10 seconds.

10s

Change different views - Split

Press SPLIT to view the images from all baby units at once.

Dim mode

With dim mode preset to on, your parent unit display will dim after 10 minutes of inactivity to conserve energy.

10 min inactivity

Press any buttons

At least 1 meter

(3 feet)

63ē

LCD is turning of

f...

Alert Tone

Low Battery Tone

No Link Alert

Sound alert in split-view

]KXOTMU

LL

]KXOTMU

LL

Sound-activated Screen

O

Sound activation

NOTES

TIP

Automatically turns on the parent unit screen when the baby unit being viewed detects a sound after the screen is turned off. When no sound is detected within 50 seconds, the screen is automatically turned off to save power.

Overview - Parent unit

Light indicators

Overview - Baby unit

Basic operation - Parent unit

Adjust speaker volume

Press + / VOL / - to adjust your parent unit speaker volume. It determines the volume of sound transmitted from your baby units.

Pan, tilt, zoom

Press and hold , , or to move the camera.

Microphone

Zoom

TALK

+ / VOL / -

Talk to your baby unit

Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit.

On/off

MENU/SELECT

Arrow keys

Turn off the screen

Press and hold LCD ON/OFF to turn off the screen. You can still hear sound from the selected baby unit.

VIEW / LCD ON/OFF

PATROL

SPLIT

Use the menu

Press MENU/SELECT to enter the menu, choose a menu item, or save a setting.

While in the menu:

Press or to scroll up or down.

• Press to select an item.

• Press BACK to return to the main menu or

• idle screen.

Antenna

Speaker

Stand

Turn off the parent unit

Press and hold to power off your parent unit.

Light sensor

Infrared LEDs

Speaker

Antenna

Camera

Temperature sensor

ON/OFF switch

Microphone

ON/OFF light

+ / VOL / -

Basic operation - Baby unit

Adjust speaker volume

Press + / VOL / - to adjust your baby unit speaker volume. It determines the talkback volume transmitted from your parent unit.

Turn off the baby unit

Slide the ON/OFF switch to the right to power off your baby unit.

Night vision

Press to zoom in or out.

Long press

Mount the baby monitor (optional)

The baby unit has infrared LEDs that allow you to see your baby at night or in a dark room. When the baby unit detects low light levels, the infrared LEDs turn on automatically. The images from this baby unit is in black and white, and appears on screen.

It is normal if you see a short white glare on your pare nt

• unit scree n as the baby unit is ad apting to the dark environment.

When the i nfrared LEDs are on, t he image i s in black

• and whit e. This is normal due to extern al light s ources .

Check for reception strength and

•

Depending on the surroundings and other interfering

• factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit’s angle, or place the baby unit at a higher level to prevent glare and blurry display.

camera angle before drilling the holes.

Place the wall mount bracket on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).

If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are ﬂush with the wall.

Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole ﬁrst, so that the wall mount bracket position is ﬁxed. You can tighten the other screw in the top hole.

Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit.

Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed.

Place the baby unit on the wall mount bracket. Tighten the screw into the threaded socket at the bottom to secure the baby unit. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place.

The default angle of the wall mount bracket is 90 degrees. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.