VTech VM342, VM342-2 User Manual

Congratulations

on purchasing your new VTech product. Before using this product, please read Important safety instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate your new VTech product. Please review this manual thoroughly to ensure proper installation and operation of this innovative and feature rich VTech product.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

What’s in the box

Install the battery

The parent unit runs on rechargeable batter y or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only.

NOTE

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.

Install the battery as shown below.

NOTES

• Press down on the battery compartment cover to pull it out.

NOTES

• Make sure the label THIS SIDE UP is facing up while inserting the battery.

Replace the battery

To replace the battery, press down on the battery compartment cover and pull it out , then follow the steps above to install the batte ry.

NOTE

• Use only the power adapters supplied with this product.

• Make sure the electrical outlets are not controlled by wall switches.

• The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if they are plugged into a ceiling, under-the-table or cabinet outlet.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

Connect the baby monitor

Charge the parent unit battery

When you have connected the parent unit and installed its battery for the first time or after power outage, the parent unit powers on automatically. The battery icon indicates the battery status (see the following table).

NOTE

• The parent unit battery is fully charged after

3 hours of continuous charging.

• It takes longer to charge the battery when the

parent unit is turned on. To shorten the charging time, turn the parent unit off while charging.

• The standby time varies depending on the

sensitivity level you set, your actual use and the age of the battery.

Battery indicators

Battery status

Action

The battery icon is off and

displays.

No battery is installed but operates using AC power, or the battery has been installed incorrectly.

Install the parent unit battery. Charge without interruption (at least 30 minutes).

The screen displays

Battery low at Parent Unit and

. The light flashes.

The battery has very little charge and may be used

for only a short time.

Charge without interruption (about 30 minutes).

The battery icon becomes solid .

The battery is fully charged.

To keep the battery charged, connect it to AC power when not in use.

Before use

NOTE

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such.

Test your baby monitor

You may test the baby monitor before initial use, and at regular times thereafter.

CAUTION

• For hearing protection, make sure the parent unit is more than 3 feet (1 meter) away from the baby unit. If you hear any high-pitched noise, move the parent unit further until the noise stops. You can also press

on the

parent unit to lower or mute the noise.

1. M ake sure your baby units and parent unit

are on.

2. The parent unit disp lays images from the

baby unit.

• Speak towards the baby unit microphone. You will hear the sound at the parent unit.

3. If you have two baby units, press VIEW on your parent unit. The screen switches to other baby units. Then, repeat step 2.

NOTE

• When the parent unit displays a nd then No link

to CAM # (# represents the baby unit number),

and the LINK LED light flashes, move the parent unit closer to the baby unit (observe the m inimum distance of 3 feet/ 1 meter). You can also check if the baby monitor is connected to a li ve power socket and switched on.

TIP

• Increase the parent unit speaker volume if you

cannot hear the sounds transmitted from the baby unit.

Positioning the baby monitor

CAUTION

• Keep the baby units out of the reach of your baby. Never place or mount the baby units inside the baby’s crib or playpen.

NOTE

• To avoid interference from other electronic devices, place your baby monitor far away from devices such as wireless routers, microwaves, cell phones and computers.

1. Pl ace the baby units more than 3 feet

(1 meter) away from your baby.

2. Adjust the angle of th e baby unit camera to

aim at your baby.

3. Bend down the temper ature sensor so

that it stays away from baby unit to avoid deviation of temperature detection.

4. Place the parent unit m ore than 3 feet

(1 meter) away from the baby units.

CAUTION

• The default volume of yo ur parent unit is

level 4, and the maximum volume is level 7. If you experience high-pitched screeching noise from your baby monitor while positioning:

- Make sure your baby units and parent unit are more than 3 feet (1 meter) apart, OR

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is up to 1,000 feet (300 meters) outdoors or 160 feet (50 meters) indoors. The actual operating range may vary depending on the environmental conditions and other interferences such as walls, doors and other obstructions.

Install the lens (optional)

The wide-angle lens (VM101) provided allows you to view more of your baby’s room from the parent unit screen. Install the wide-angle lens onto the baby unit camera as shown below.

Remove the lens

NOTE

• When the lens is not in use, cover both sides of the lens with the lens covers provided to avoid scratches.

• You can purchase and install an extra new wid eangle lens (VM101) onto your baby unit if necessary.

Overview

Baby unit overview

Light sensor

Camera

Infrared LEDs

ON/OFF light

• On when the baby unit is turned on.

• Flashes when the baby unit is not being viewed; or when the link to the parent unit is lost.

Play/Stop

• Press to play or stop lullaby on the baby unit.

Microphone

Skip

• Press to play the next lullaby.

+ VOLUME -

• Press to adjust the speaker volume. It determines the lullaby volume and talkback volume transmitted from parent unit.

ON/OFF switch

• Slide to turn on or off the baby unit.

Speaker

Temperature sensor

12 Threaded socket

• For wall mount installatio n use.

PAIR

• Your baby units and parent unit provided are already paired.

Power jack

Parent unit overview

LED lights

• Indicate the different statuses of the parent unit. For details, refer to Parent unit lights.

Microphone

On/off

• Press and hold to power on.

• Press and hold again to power of f.

TALK

• Press and hold to talk to the s elected

baby unit in SINGLE-CA M or PATROL mode.

Zoom

• Press to zoom in or out while viewi ng

image in SINGLE-CA M or PATROL mode.

• While in a menu, press to ch oose an

item.

• While viewing zoomed im age,

press and hold to move the zoomed image rightward.

• While in SPLIT mod e, press to move

the selection box rightward.

BACK

• While in a menu, press to return to the main menu or idle screen.

• While viewing zoomed image, press and hold to move the zoomed image leftward.

• While in SPLIT mode, press to move the selection box leftward.

VIEW / LCD ON/OFF

• Press and hold to turn off t he parent

unit screen.

• Press to view the image of the

next baby unit in SINGLE- CAM or

PATROL mode.

PATROL

• Press to turn on or off the PATROL

mode.

SPLIT

• Press to turn on or off the S PLIT

mode.

• Press to increase the paren t unit

speaker volume.

• Pres s to decrease the parent unit

speaker volume.

MENU/SELECT

• Press to enter the menu.

• While in a menu, press to choose an item, or save a setting.

• While in a menu, press to scroll up.

• While viewing zoomed image, press and hold to move the zoomed image upward.

• While in SPLIT mode, press to move the selection box upward.

• While in a menu, press to scroll down.

• While viewing zoomed image, press and hold to move the zoomed image downward.

• While in SPLIT mode, press to move the selection box downward.

Antenna

Stand

Speaker

Power jack

Battery compartment cover

Parent unit lights

LINK

• On when the parent unit is linked to

the baby unit.

• Flashes when the link to t he baby

unit being viewed in SINGLE- CAM or PATROL mode is lost; or when the link to at least one baby unit being viewed in SPLIT mode is lost.

• On when the parent unit is

connected to AC power, or the battery is charging.

• Flashes when the parent u nit

battery is low and needs charging.

• Off when the pare nt unit is

disconnected from AC power.

It turns on:

• When the speaker volume of the

parent unit is turned off; or

• When the parent unit is in SPLIT

mode; or

• When the parent unit is talking to

the baby unit.

TALK

• On when the parent unit is talkin g

to the baby unit.

Parent unit status icons

Connection status

•

displays when strong signal strength is detected between

the baby unit and the parent unit.

•

or displays when moderate

or low signal strength is detected between the baby unit and the parent unit.

•

displays when the link between the baby unit and the parent unit

is lost.

Lullaby

• Displays when the baby unit being viewed is playing lullaby.

Current view status

• Displays the baby unit number of the baby unit that is being viewed when in SINGLE-CAM and PATROL mode.

• Displays the baby unit number of the selected baby unit when in

SPLIT mode.

PATROL mode

• Displays when the parent unit is in PATROL mode.

• For VM342-2 only

SPLIT mode

• Displays when the parent unit is in SPLIT mode.

• For VM342-2 only

Night vision

• Displays when the baby unit being viewed has activated the night vision feature.

Zoom

• Displays when the current image on the parent unit has zoomed in.

Temperature alert tone

• Displays when the temperature alert tone is set on.

F or

Real-time temperature

• Displays the real-time temperature detected by the baby unit in Fahrenheit (

F) or Celsius (oC)

(e.g. 57

F or 14 oC).

Mute alert

• Displays when the parent unit speaker volume is set to off.

• Displays when SPLIT mode is turned on.

9-level sound indicator

•

(1 to 3 bars) indicates low sound level detected by the baby unit.

•

(4 to 6 bars) indicates moderate sound level detected by the baby unit.

•

(7 to 9 bars) indicates high sound level detected by the baby unit (e.g. baby crying loudly).

Speaker volume

• Displays the parent unit speaker volume level while adjusting.

Battery status

•

animates

when the battery is charging.

•

displays solid when the battery

is fully charged.

•

displays when the battery is low and needs charging.

AC power without battery

• Displays when the parent unit is connected to AC power without the battery.

Parent unit main menu icons

Alert Tone

You can set the parent unit to beep when

• the parent unit operates in low battery condition;

• the link between the parent unit and the baby unit is lost; or

• the baby unit detects sounds while in SPLIT mode.

Language

You can select a lan guage (English, French or Spanish) to be used in all screen displays.

LCD

You can change the br ightness of the parent unit screen, or turn on the Dim Mode to save power.

Pair/Unpair CAM

The baby unit and parent unit provided are already paired.

Rename

You can choose a sp ecific name for the baby unit from a pre-defined name list.

Sensitivity

With this feature, you can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit.

Sound-activated Screen

When the baby unit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen turns on automatically. It will then turn off again after 50 seconds of no sound detection.

Temperature

You can choose to set the maximum/ minimum temperature and turn on the Temperature alert tone, so that the parent unit beeps whenever the room temperature detected by the baby unit falls outside of the desired temperature range. You can choose to display the temperature in Fahrenheit (

F) or

Celsius (

C) on your parent unit.

Vibration

You can turn on the vibration alert so that the parent unit vibrates when it receives No link alert, Sound alert

in split-view or Temperature alert tone after turning on the respective

alert tones.

Parent unit display messages

No link to

CAM # *

The selected baby unit is out of range or is turned off.

Battery low at

Parent Unit

The battery level of the parent unit is very low and needs to be recharged.

Battery empty. Powering off ...

The battery is empty and needs to be recharged.

Sound

detected at CAM #

The sound level exceeds the threshold at CAM # in

SPLIT mode.

Temperature

too high at CAM #

Temperature too low at

CAM #

The temperature detected by the baby unit is higher/ lower than the desired temperature alert range.

Powering on...

The parent unit is turning on.

The parent unit is searching for baby units.

* # represents the baby unit number.

Using the baby monitor

Power on or off the baby unit

• Slide ON/OFF switch upward to turn on the baby unit. The ON/OFF LED light turns on.

• Slide

ON/OFF switch downward to turn off the baby unit. The ON/OFF LED light turns off.

Power on or off the parent unit

• Press and hold to turn on the parent unit. The screen turns on.

• Press and hold

again to turn off the

parent unit. The screen turns off.

Turn on or off the parent unit screen

You can turn on or off the parent unit screen without powering off the parent unit. You can still hear sound from the baby units.

• Press and hold LCD ON/OFF on the parent unit to turn off the screen.

• Press any keys on the parent unit to turn on the screen again.

Adjust speaker volume

To adjust parent unit speaker volume:

• Press or on the parent unit at any time when viewing images

NOTE

• When the parent unit speaker volume is set to

zero, appears on the scr een and the light turns on.

To adjust baby unit speaker volume:

The baby unit speaker volume determines the lullaby volume and talkback volume transmitted from parent unit.

• Press + VOLUME - on the baby unit to adjust the speaker volume.

Play lullaby on the baby unit

The baby monitor has five lullabies and four soothing sounds for you to comfort your baby.

To play lullaby or soothing sound on the baby unit:

You can play lullaby or soothing sound on the baby unit. You can also control the volume level.

• Press

/ on the baby unit to play lullaby.

• Press

on the baby unit to play the next

lulla by.

• Press

/ again to stop the lullaby.

• Press + VOLUME - to adjust the volume level of the lullaby on the baby unit.

TIP

• When the lulla by stops, press / again to replay.

Set the language

You can select a language (English, French or Spanish) to be used in all screen displays.

1. Press MENU when the parent unit is idle.

2. Press

or to choose Language, then

press SELECT.

3. Press

or to choose English, Français or Español, then press SELECT to confirm your selection.

Adjust LCD brightness

You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD brightness is preset to Level 3.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose LCD, then press SELECT.

3. Press SELECT again to choose Brightness.

4. Press

or to choose the desired level of brightness, then press SELECT to confirm your selection.

Turn on or off the dim mode

The dim mode is preset to on to help you save the parent unit power. Your parent unit display will dim automatically after 10 minutes of inactivity, in which there is neither key pressed nor alert received from the baby unit.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose LCD, then press SELECT.

3. Press

or to choose Dim Mode, then press SELECT.

4. Press

or to choose On or Off, then press SELECT to confirm your selection.

NOTE

• While the scree n is dimmed, any keypress or alert message will trigger th e screen to return to the preset brightness level. After 10 minute s of inactivity, it will be dimmed again.

Adjust the sound sensitivity of the baby unit

You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sensitivity level is preset to HIGHEST.

Sensitivity

Level

Description

Highest

Highest sensitivity level

The parent unit speaker is constantly on, and you will hear all sounds (including background noises) from your baby’s room.

High

High sensitivity level

The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly.

Medium

Medium sensitivity level

The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

Low

Low sensitivity level

The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

Lowest

Lowest sensitivity level

The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Sensitivity, then

press SELECT.

• If you have two baby units, the system prompts you to choose both baby units or the desired baby unit, press

or to choose ALL CAM or CAM #, then press SELECT.

3. Press

or to choose the desired

sensitivity level, then press SELECT

confirm your selection.

VM342

VM342-2

Full Color Video Monitor

with Wide-Angle Lens

1 set for VM342

2 sets for VM342-2

1 set for both VM342 and VM342-2

Connect and charge the battery

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

User’s manual

Go to www.vtechphones.com for the latest VTech product news.

Strangula

tion

Hazard

Keep

th is cord

o ut of re

ach

o f ch il dren.

The

co rd nee

d s t o b e at l e as t three

feet

away fro

m the

ch il d at all ti

mes.

Do no

us e with

an exte

n sio n co

rd . D o n ot

re move t

h is tag.

Élo i g nez ce

co rdo n des enfan

ts. Le

cord

on d oit s e trou

ver à au m

oin s trois

pie d s d’un

en fant e

t ce,

en to ut te

mps.

N’ u ti li se z p as de

ral l o ng e . Ne retirez pas

cette

éti q uette

Ma n te n ga este

cab le fuera

de la alcanc

de l os n iñ os. Este ca

b le debe

es ta r por

lo meno

s t res p ies fu

era de

l a al cance

del ni

ño en tod

o m o me n to. No lo us

con

u na e

xtens

ió n i n alámbrica.

No q uit e

esta

etiq ueta.

Risque

d’étranglement

Riesgo de

est rangulación

63℉

> 3ft (1m)

63ē

＞3ft (1m)

＜3ft (1m)

j k

Low

sensitivity

High

sensitivity

TIP

• You can adjust the baby unit placement to improve the sound detection.

Turn on or off the sound activation

When sound activation is on, as long as no sound is detected within 50 seconds, the parent unit screen will turn off automatically to save power. When your baby unit detects a sound, which exceeds the selected sensitivity level, the sound activation triggers the parent unit screen to turn on automatically. When no sound is detected within 50 seconds, the screen will be off again.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Sound-activated

Screen, then press SELECT.

3. Press

or to choose On or Off, then press SELECT to confirm your selection. The screen returns to main menu.

NOTE

• Sound activati on is available in SINGLE-CAM and PATROL mode only.

• If the sound sensitivity is set to Highest, the parent unit screen may remain on continuously even though sound activation is on. This depends on whether the baby unit detects any sounds.

Monitoring mode

for VM342-2 only

Every time the parent unit is turned on, it displays a baby unit in SINGLE-CAM mode. If there are two baby units in your system, you can also monitor your baby in PATROL or

SPLIT mode.

SINGLE-CAM

The screen displays a single baby unit in full screen.

PATROL

A single cam view that transits to a different baby unit every 10 seconds.

SPLIT

The screen displays all baby units.

In SINGLE-CAM or PATROL mode:

• Press VIEW to view the next baby unit.

• Press PATROL to switch to PATROL mode if you are in SINGLE-CAM m ode, and vice versa.

• Press SPLIT to enter the SPLIT mode.

In SPLIT mode:

• Press

, , or to select a baby unit.

• Press

or VIEW key to view the selected baby unit temporarily in SINGLE- CAM mode. It returns to SPLIT mode after 10 seconds.

NOTES

• The parent unit is muted while in SPLIT mode.

Zoom

You can zoom in or out while viewing image from baby unit in SINGLE-CAM and PATROL mode.

• Press

to zoom in.

• Press and hold

or to move the zoomed

image upward or downward.

• Press and hold

or to move the zoomed

image leftward or rightward.

• Press

again to zoom out.

Talk

You can use the TALK function of the parent unit to comfort your baby in SINGLE-CA M and PATROL mode.

1. Press and hold TALK o n the parent unit. The TALK light turns on.

2. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.

3. Release TALK to stop the broadcast. The TALK light goes off. The speaker is then turned on for around 20 seconds, so you can hear your baby.

NOTE

• The parent unit sp eaker is muted during voice

broadcast. Sound transmiss ion from the baby unit resumes after TALK is released.

• After around 20 se conds of sound

re-transmission, the speaker r eturns to mute if you had set it to mute before pressing TAL K.

Set alert tone

Low battery tone

You can set the parent unit to beep when the parent unit operates in low battery condition.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Alert Tone, then

press SELECT.

3. Press SELECT again to choose Low Battery Tone.

4. Press

or to choose On or Off, then

press SELECT

to confirm your selection.

No link alert

You can set the parent unit to beep when the link between the parent unit and the baby unit is lost.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Alert Tone, then

press SELECT.

3. Press

or to choose No Link Alert, then

press SELECT.

4. Press

or to choose On or Off, then

press SELECT

to confirm your selection.

Sound alert in split-view

You can turn on the sound alert feature so that, while in SPLIT mode, the parent unit beeps and displays Sound detected at CAM # whenever the baby unit detects sounds.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Alert Tone, then

press SELECT to select.

3. Press

or to choose Sound Alert in

split-view, then press SELECT.

4. Press

or to choose On or Off, then

press SELECT

to confirm your selection.

NOTES

• The sound aler t feature is only available in SPLIT mode.

Monitor the temperature

Your baby unit monitors the temperature of your baby’s room with its built-in temperature sensor. If the detected temperature is outside of the preset temperature range, the parent unit will display alert message.

Set temperature range

You can set the desired room temperature alert range. The minimum temperature can be set between 52

F (11 oC) and 69 oF (20

C). The maximum temperature can be set

between 70

F (21 oC) and 86 oF (30 oC).

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Temperature, then

press SELECT.

3. Press

or to choose Minimum or

Maximum, then press SELECT.

• If you have two baby units, the system prompts you to choose both baby units or the desired baby unit, press

or to choose ALL CAM or CAM #, then press SELECT.

4. Press

or to choose the desired minimum or maximum temperature, then press SELECT

to confirm your selection.

Temperature alert tone

You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the detected temperature is out of range.

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Temperature, then

press SELECT.

3. Press

or to choose Alert Tone, then

press SELECT.

• If you have two baby units, the system prompts you to choose both baby units or the desired baby unit, press

or to choose ALL CAM or CAM #, then press SELECT.

4. Press

or to choose On or Off, then

press SELECT to confirm your selection.

Temperature format

You can choose to display the temperature in Fahrenheit (

F) or Celsius (oC).

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Temperature, then

press SELECT.

3. Press

or to choose Format, then press

SELECT.

4. Press

or to choose Fahrenheit or Celsius, then press SELECT to confirm your selection.

Turn on or off the vibration

You can turn on the vibration feature so that the parent unit vibrates when it receives any of these alerts (after turning on the respecti ve alert tones):

• Sound alert in split-view

• No link alert

• Temperature alert tone

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Vibration, then

press SELECT.

3. Press

or to choose On or Off.

4. Press SELECT

to confirm your selection.

NOTES

• If the vibration fea ture is turned on, the parent unit may vibrate as it receives sound broadcas t from the baby unit.

Rename the baby units

You can rename each baby unit. Once the baby unit is renamed, its new name together with the baby unit number will appear in the sub-menu of below options:

• Sensitivity • Rename

• Temperature • Pair/Unpair CAM

1. Press MENU when the parent unit is i dle.

2. Press

or to choose Rename, then press

SELECT.

3. Press

or to choose the desired baby

unit, then press SELECT.

4. Press

or to choose the desired name for the baby unit, then press SELECT to confirm your selection.

Night vision

The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The image from this baby unit is in black and white, and

appears on screen.

NOTE

• It is normal if you see a sh ort white glare on your parent unit screen as the baby unit is adapti ng to the dark environment.

• When the infrare d LEDs are on, the images are in black and white. This is normal.

TIP

• Depending on the surroundings and other interfering factors, like lightings, objects, colors and backgrounds, the display resolution may vary. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry display.

Mount the baby unit (optional)

Your baby monitor comes ready for tabletop use. You can also choose to mount your baby unit on the wall. See Mount the baby unit (optional) in the Quick Start Guide for the wall mounting instructions.

To keep this product working well and looking good, follow these guidelines:

• Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or fluorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the baby

unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry

before you connect them to the mains again.

When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.

Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.

Why does the baby monitor not respond normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby units and the parent unit.

2. Remove the batteries in the parent unit. Then, install the batteries again.

3. Wait a few seconds before connecting power back to the baby units and the parent unit.

4. Turn on the baby units and the parent unit.

5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for this to take place.

Why don’t the power-on light of the baby unit and parent unit go on when I switch on the units?

Perhaps the parent unit is not connected to the mains. Insert the appliance plug into the parent unit and put the adapter in a wall socket. Then, press and hold POWER to switch on the parent unit and to establish connection with the baby unit.

Perhaps the baby unit is not connected to the mains. Connect the baby unit to the mains. Then, set the

ON/OFF switch to ON to switch on the baby unit and to establish connection with the parent unit.

Why doesn’t my parent unit charge while connected to AC power?

Make sure the power is not controlled by a wall switch.

Make sure the battery is correctly installed in your parent unit.

You may have used the battery for a long time. Replace a new battery.

Why is my screen in black and white?

The screen is in black and white during nighttime or in a dark room. This is normal.

Why do I get glare or blurry display on my screen when viewing my baby at night?

During nighttime or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect the image quality on your parent unit screen. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare and blurry display.

Why does the baby monitor produce a high-pitched noise?

The parent unit and baby units may be too close to each other.

• Move the parent unit away

from the baby units until the noise stops; OR

• Turn down the volume of your

parent unit.

The ON/OFF light on the baby unit flashes and the parent unit displays

in main menu.

Follow below steps to pair the baby unit. Make sure both parent unit and baby unit are on before pairing.

1. Press MENU when the parent unit is idle.

2. Press or to choose Pair/

Unpair CAM, then press SELECT.

3. Press SELECT again to

choose Pair CAM.

4. Press or to choose an

empty baby unit slot, then press SELECT. The parent unit screen displays Press

and hold the pair button at the CAM for 5 seconds until the power indicator flashes..

5. Immediately press and hold

PAIR on the bottom of the baby unit with a narrow pointed object such as a pencil. The LED light flashes quickly.

When pairing is successful, the screen displays the view of newly paired baby unit in SINGLE-CAM mode. The LED light on the baby unit remains on.

• If pairing fails, the screen

displays Pairing failed. Try the pairing process again.

• Only one baby unit can be

paired at a time.

I have accidentally unpaired my baby unit.

Why does the parent unit beep?

The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet).

If the parent unit is powered by the provided battery, it may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 3 hours.

If your parent unit is in SPLIT mode, some of your baby units may detect sounds.

The temperature of your baby’s room may be too high or too low.

Why does the parent unit beep/vibrate frequently in SPLIT mode?

You may have set the sound sensitivity level to Highest when the sound alert (and vibration) feature is turned on. The parent unit notifies you of all sounds including background noise with beeps (and vibrations). Adjust the sound sensitivity to a lower level.

Why does the parent unit react too quickly to other sounds?

The baby unit also picks up other sounds than those of your baby. Adjust the sensitivity level to a lower level or lower the parent unit speaker volume.

Why don’t I hear a sound/ Why can’t I hear my baby cry?

The parent unit speaker volume may be too low or off. Press

increase the volume. You may have set a low sound

sensitivity level. See Adjust the

sound sensitivity of the baby unit to set to a higher level.

Why does the sound from my baby monitor become intermittent or even drop out?

The baby unit does not pick up soft sounds if the sensitivity level is set to a lower level. Adjust the sensitivity level to Highest to hear all sounds from your baby’s room. See Adjust the sound sensitivity of the baby unit to set to a higher level.

Why can’t I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions?

The baby units may be out of range. Move the parent unit closer to the baby units (observe the minimum distance of 3 feet/ 1 meter).

Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible.

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such.

4. This product is not intended for use as a medical monitor.

5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT198555/ BT298555) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC

seal.

7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: Output: 6V DC 600mA Parent unit power adapter: Output: 5V DC 1A.

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

11. Unplug the power cords before replacing batteries.

12. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

20. You should test the sound reception every time you turn on the units or move one of the components.

21. Periodically examine all components for damage.

22. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc.

23. Children should be supervised to ensure that they do not play with the product.

24. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32

F and 104oF.

2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.

4. Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft away). Do not remove this tag.

5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket.

6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.

• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

The RBRC

seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The RBRC

program provides a convenient alternative to placing used lithium-ion batteries into the trash or municipal waste, which may be illegal in your area. VTech’s participation in RBRC

makes it easy for you to drop off the spent battery at local retailers participating in the RBRC

program or at authorized

VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Li-ion

battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

RBRC® and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery Recycling Corporation.

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation. The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.

This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.

RF radiation exposure statement

The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energyconserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. Ce produit a été conçu pour être un dispositif d’appoint seulement. Il n’est pas le remplacement d’une supervision responsable et adéquate par un adulte et ne devrait pas être utilisé comme telle.

4. Ce produit n’est pas conçu pour être utilisé en tant que moniteur médical.

5. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.

6. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le mauvais type de piles pour l’unité du parent. N’utilisez que le

bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT198555/BT298555). N’incinérez pas les piles. Celles-ci risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant

le sceau du RBRC

7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement le produit et mettre votre sécurité en péril. Adaptateur de l’unité du bébé : Sortie : 6 V CC 600mAAdaptateur de l’unité du parent : Sortie : 5 V CC 1A

8. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond, sous une table ou dans un meuble.

9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, aﬁn d’assurer une accessibilité sécuritaire à la prise de courant.

10. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer.

11. Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.

12. Ne coupez pas les cordons d’alimentation pour remplacer les ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.

15. Ne surchargez pas les prises de courant murales ni les rallonges électriques.

16. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.

17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

18. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

19. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.

20. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.

21. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas endommagées.

22. Soyez avisé de la perte de la conﬁdentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par d’autres moniteurs de bébé, des téléphones sans ﬁl, des scanneurs, etc.

23. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne jouent pas avec l’appareil.

24. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné sufﬁsamment de supervision ou d’instructions relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.

4. Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, à au moins 1 mètre (3 pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.

5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) : L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes es normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return

the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or

3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or

4. Product to the extent that the problem is caused by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see item 2 below); or

8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service, please visi t our website at www.vtechphones.com or call 1 (80 0) 595-9511. NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warra nty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further

repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents

including the Product to the VTech service location along with a description of the malfunction or difficulty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/ provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Frequency control

Crystal controlled PLL synthesizer

Transmit frequency

Baby unit: 2405 - 2475 MHz Parent unit: 2405 - 2475 MHz

Channels 32

LCD 4.3” Color LCD

(WQVGA 480 x 272 pixel)

Nominal effective range

Maximum power allowed by FCC. Actual operating range may vary according to environmental conditions at the time of use.

Power requirements

Parent unit: 3.7V Li-polymer battery Baby unit power adapter: Output: 6V DC @ 600mA Parent unit power adapter: Output: 5V DC @ 1A

Credits:

The Background Noise sound file was created by Caroline Ford, and is used under the Creati ve Commons license. The Stream Noise sound file was created by Carol ine Ford, and is used under the Creative Co mmons license. The Crickets At Night sound fi le wa s cre ated by Mik e Koen ig, and is used under the Creative Co mmons license. The Heart Beat sound file was crea ted by Za rabad eu, and is used under the Creative Commo ns license.

General product care

Storage

FCC and IC regulations

The RBRC® seal

Limited warranty

Frequently asked questions

Press VIEW

10s

For cETL compliance only

California Energy Commission battery charging testing mode

Important safety instructions

Technical specications

VTech VM342, VM342-2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual