VTech LS6405 User Manual

®
User’s manual
Accessory handset for use with VTech models LS6425/LS6426/ LS6475/LS6476
w w w.v t e c h p h o n e s . c o m
Model: LS6405
T
Compatible with
Hearing Aid T-Coil
TIA-1083
on purchasing your new VTech product. Before using this telephone, please read Important safety instructions on page 10 of this manual.
This manual has instructions on how to set up and register your new handset. For complete instructions on using the handset, see the user’s manual that came with your telephone base.
If you cannot nd the user’s manual, you can view or download it at www.vtechphones.com. In Canada, visit www.vtechcanada.com.
The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it meets the latest energy efficiency guidelines.
Telephones identified with this logo have reduced noise and interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license.
Table of contents
Getting started ........................................................................1
Parts checklist ..........................................................................1
Battery installation ....................................................................2
Battery charging .......................................................................3
Add and register a handset ......................................................4
Deregister handsets .................................................................5
Handset layout..........................................................................6
Appendix .................................................................................9
Battery ......................................................................................9
Important safety instructions...................................................10
Precautions for users of implanted cardiac pacemakers ........11
Operating range......................................................................11
Maintenance ...........................................................................11
About cordless telephones .....................................................12
The RBRC® seal .....................................................................12
FCC, ACTA and IC regulations ..............................................13
Limited warranty .....................................................................15
Technical specications..........................................................17
i
Getting started

Parts checklist

Your telephone package contains the following items. Save your sales receipt and original packaging in case it is necessary to ship your telephone for warranty service.
Battery Battery
compartment cover
®
User ’s man ual
Accessory handset for use with VTech models LS6425/LS6426/ LS6475/LS6476
ww w.v t ec hp ho ne s. co m
Model: LS6405
Handset charger and charger adapter
User’s manual
To purchase replacement batteries or power adapters, visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
1
Handset
Getting started
Battery installation
Install the battery as shown below.
Plug the battery connector securely into the socket inside the handset battery
1. compartment, matching the color-coded label.
Place the battery with the label THIS SIDE UP facing up and the wires inside
2. the battery compartment.
Align the cover flat against the battery compartment, then slide it towards the
3. center of the handset until it clicks into place.
Charge the handset by placing it in the telephone base or charger. The
4. CHARGE light is on when the handset is charging.
1 2
3
CHARGE light remains on when charging.
If the handset will not be used for a long time, disconnect and remove the
• battery to prevent possible leakage.
To purchase replacement batteries, visit our website at www.vtechphones.com
• or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
4
2
Getting started
Battery charging
Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 10 hours of continuous charging. See the table on page 9 for battery operating times.
If the screen is blank or displays Place in charger, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. When the battery is low, the handset displays Low battery along with a flashing icon. If you are on a call in low battery mode, the handset plays short beeps to alert you.
The following table summarizes the battery charge indicators and actions to take.
Battery indicators Battery status Action
The screen is blank, or displays Place in charger and flashes.
The screen displays Low battery and flashes.
The screen displays HANDSET X.
If you place the handset in the telephone base or charger without installing a battery, the screen displays No battery.
Battery has no or very little charge. The handset cannot be used.
Battery has enough charge to be used for a short time.
Battery is charged. To keep the battery charged,
Charge without interruption (about 30 minutes).
Charge without interruption (about 30 minutes).
place it in the telephone base or charger when not in use.
After you install your telephone or power returns following a power outage, the handset will prompt you to set the date and time. To skip setting the date and time, press OFF/CANCEL.
SET DATE MM/DD/YY
3
Getting started
Add and register a handset
You can add new handsets (LS6405, purchased separately) to your telephone system. Each handset must be registered with the telephone base before use. When first purchased, each handset displays Put HS on BASE to register. You may need to charge the handset before registering it to the telephone base. For more details on battery charging, see page 3.
To register a handset:
Make sure the handset is out of the telephone base
1. or handset charger and shows Put HS on BASE to register and then place the handset in the telephone base.
The handset displays Registering...Please wait and
2. the red IN USE light on the telephone base turns on. It takes about 90 seconds to complete the registration process. The handset displays HANDSET X Registered (X represents the registered handset number). The IN USE light turns off and the handset beeps when registration completes.
If registration fails, the system will automatically try to register again. If registration fails after the third try, the handset displays Registration failed then Put HS on BASE to register. This may take up to five minutes to occur.
To reset the handset, remove it from the telephone base. When the handset displays Put HS on BASE to register, try the registration process again.
After registration, the date and time need to be reset.
4
Loading...
+ 14 hidden pages