VTech IS7121-2 User Manual

Abridged user’s manual

T

Compatible with

Hearing Aid T-Coil

TIA-1083

IS7121/IS7121-2/IS7121-22

DECT 6.0 cordless telephone
with wireless doorbell

Register online to get an additional 3-month warranty!

Go to www.vtechphones.com to register your product for enhanced warranty
support and latest VTech product news.

Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083 Compliant Logo is
a trademark of the Telecommunications Industry Association.
Used under license.

The ENERGY STAR® program (www.energystar.gov) recognizes
and encourages the use of products that save energy and help
protect our environment. We are proud to mark this product with
the ENERGY STAR® label indicating it meets the latest energy
efficiency guidelines.

IMPORTANT

Refer to the Installation guide provided in this product package to install this
product before you can configure your telephone system.

Introduction

To help protect the environment, this Abridged user’s manual provides you
with some basic setting and operation instructions. A limited set of features are
described in abbreviated form.

Please refer to the online Complete user’s manual for a full set of installation and
operation instructions at www.vtechphones.com.

Before using this VTech product, please read Important safety instructions on
page 12 of this user’s manual.

BC

1

Parts checklist

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.

Screw for doorbell
(bottom)

(1 for IS7121/IS7121-2)
(2 for IS7121-22)

Handset

(1 for IS7121)
(2 for IS7121-2/
IS7121-22)

Wall anchors

(2 for IS7121/
IS7121-2)
(4 for IS7121-22)

Double-sided
adhesive tape

(2 for IS7121/
IS7121-2)
(4 for IS7121-22)

Doorbell power
adapter

(1 for IS7121/
IS7121-2)
(2 for IS7121-22)

Battery compartment
cover

(1 for IS7121)
(2 for IS7121-2/IS7121-22)

Doorbell wall mount
plate

(1 for IS7121/IS7121-2)
(2 for IS7121-22)

Handset charger
and charger adapter

(1 for IS7121-2/
IS7121-22)

Battery

(1 for IS7121)

(2 for IS7121-2/
IS7121-22)

Telephone base

Doorbell

(1 for IS7121/
IS7121-2)
(2 for IS7121-22)

Abridged u ser’s manual Installati on guide

Screws for doorbell
wall mount

(2 for IS7121/IS7121-2)
(4 for IS7121-22)

Telephone base
power adapter

Doorbell wall
mount cover

(1 for IS7121/
IS7121-2)
(2 for IS7121-22)

Telephone
line cord

Wall mount
bracket

Doorbell overview

Infrared LEDs

/DOORBELL

Alkaline
batteries

(2 for IS7121/
IS7121-2)
(4 for IS7121-22)

Abridged
user’s manual

Camera lens

Doorbell light

Installation
guide

2

Handset overview

1

9

10

2

3

4

5

6

7

1 – CHARGE light

2 – q/VOL-/CID

Scroll down while in a menu, or in the

•
directory, caller ID log or redial list.

Decrease the listening volume.

•
Review the caller ID log.

•

3 – /FLASH

Make or answer a call.

•

4 – 1

Set or dial your voicemail number.

•

5 – Dialing keys

6 –

Switch to tone dialing temporarily.

•
Switch the character between upper

•
and lower case.

7 –

Make or answer a call.

•
Switch between the speakerphone and

•
the handset earpiece.

8 – MUTE/DELETE

Mute the microphone.

•
Delete digits or characters.

•

9 – PUSH TO TALK (PTT)/SNAPSHOT

Begin a one-to-one or one-to-group

•
broadcast.

Take a photo shot of the visitor.

•

10 – Softkeys (2)

Select a menu item displayed above

•
the key.

8

11 – p/VOL+/

Scroll up while in a menu, or in the

•
directory, caller ID log or redial list.

Increase the listening volume.

•
Review the directory.

•

12 – /VIEW

Start video streaming.

•

13 – OFF/CANCEL

Hang up a call.

•
Return to the previous menu or idle

•
mode without making changes.

14 – 5/

During video streaming, press to zoom

•
in or out.

15 – 2/p, 8/q, 4/t and 6/u

During video streaming, press to move

•
the zoomed image upward, downward,
leftward or rightward.

16 –

Set and turn on the quiet mode, or turn

•
it off.

Show other dialing options when

•
reviewing a caller ID log entry.

Toggle the name order when saving

•
the caller ID entry into the directory.

17 – REDIAL/PAUSE

Review the redial list.

•
Insert a dialing pause.

•

11
12

13

14

15

16

17

3

Telephone base overview

1

2

3

4

1 – Message window

2 – /ANS ON/OFF

Turn on or off the answering system.

•

3 – /FIND HANDSET

Page all system handsets.

•

4 – /REPEAT

Repeat a message.

•
Press twice to play the previous

•
message.

5 – IN USE light

Using the handset menu

5
6

7

8

9

10

6 – DOORBELL light

7 – X/DELETE

Delete the playing message.

•

8 – +/VOL/-

Adjust the listening volume.

•

9 – /SKIP

Skip to the next message.

•

10 – /PLAY/STOP

Play messages.

•
Stop playing messages.

•

Press OFF/CANCEL to wake up the sleeping screen.

i

Press MENU when the handset is not in use.

1.

Press q or p until the screen displays the desired

2.
feature menu.

Press SELECT.

3.
To return to the previous menu, press CANCEL.

•
To return to idle mode, press and hold CANCEL.

•

HANDS E T

1:35am 8/20

INTCOM MENU

X

4

Telephone settings

Default settings are indicated by asterisks (*).

Settings menu Description Options

LCD language

CID time sync

Rename devices

Annc Caller ID

LCD brightness

Dim mode

Wallpaper

Voicemail #

Clr voicemail

Set the handset display language.

Enable the date and time to be set by
incoming caller ID information.

Change the name for each system device.

Enable the telephone base and/or the
handsets to announce the incoming caller ID
information.

Set the handset screen brightness.

Set the handset screen backlight when not
in use.

Set the handset wallpaper.

Set the speed dial voicemail number.

Turn off the voicemail indicators (see the
note below).

English*;
Français;
Español

On*;
Off

Local handset;
Doorbell

Set all On/Off;
Local handset;
Base

*

On*;
Off

Wallpaper 1*;
Wallpaper 2;
Wallpaper 3;
Wallpaper 4;
Wallpaper 5;
Wallpaper 6;
Wallpaper 7

VOICEMAIL #

Reset voicemail
indication?

-

Key tone

Dial mode

Doorbell setup

Use the Clr voicemail feature when the telephone indicates there is new voicemail

•
but there is none. For example, when you have accessed your voicemail while away
from home. The Clr voicemail feature only turns off the indicators; it does not delete
your voicemail messages. As long as you have new voicemail messages, your
telephone service provider continues to send the signal that turns on the indicators.

Set whether the handset beeps whenever a
key is pressed.

Set the telephone to be touch-tone or
pulse dialing.

Test the doorbell reception range and video
capture angle.

*

Off;

Touch-tone*;
Pulse

To test the
signal strength
between base
and doorbell,
press[Doorbell]
on doorbell now

The following are some of the telephone features you may wish to set. Refer
to Telephone settings in the online Complete user’s manual for complete
instructions for setting all telephone features.

Handset ringer volume

You can adjust the handset ringer volume level, or turn the ringer off.

Press MENU when the handset is not in use.

1.

Scroll to Ringers and then press SELECT twice.

2.

Press q or p to sample each volume level or press OFF to turn off the ringer,

3.

then press SET to save.

When the ringer volume is set to Off, the handset still rings when you press

•

/FIND HANDSET on the telephone base.

Chime volume

You can adjust the telephone base or handset chime volume level, or turn the
chime off.

Press MENU when the handset is not in use.

1.

Scroll to Chime and then press SELECT twice.

2.

Press q or p to choose Local handset or Base, then press SELECT.

3.

Press q or p to sample each volume level or press OFF to turn off the ringer,

4.

then press SET to save.

5

Quiet mode

You can turn on the quiet mode for a period of time. During this period, all tones
(except paging tone) and call screening are muted. When you turn on the quiet
mode, the answering system turns on automatically.

Press and hold when the handset is not in use.

1.

Use the dialing keys (0-9), or q or p to enter the duration (hour), then press SET

2.
to save.

To turn off the quiet mode, press and hold when the handset is not in use.

•

Set date and time

If you subscribe to caller ID service, the day, month and time are set automatically
with each incoming call. You can also set the date and time manually.

Press MENU when the handset is not in use.

1.
Scroll to Date & Time and then press SELECT.

2.
Use the dialing keys (0-9) to enter the month (MM), date (DD) and year (YY).

3.
Then press SET.

Use the dialing keys (0-9) to enter the hour (HH) and minute (MM).

4.
Then press q or p to choose AM or PM

Press SET to save.

5.

.

Doorbell operation

When a visitor presses /DOORBELL, it automatically captures a photo. You can
start a video streaming session without talking to the visitor.

Start a video streaming session

Press /VIEW or VIEW when the visitor presses /DOORBELL.

•

-OR-

Press /VIEW when the phone is not in use.

•

You can choose to talk to the visitor when the visitor presses /DOORBELL.

To talk to the visitor:

Press SPEAK when the visitor presses /DOORBELL.

•

-OR-

Press the flashing SPEAK during a video streaming.

•

If you do not connect the doorbell to AC power, you cannot start a video streaming

•
session with a handset.

If audio feedback occurs, press on the handset to turn off the speakerphone and

•
use the handset earpiece instead.

Options while video streaming:

Press 5/ to zoom in. Press 2/p, 8/q, 4/t or 6/u to move the zoomed image

•

upward, downward, leftward or rightward correspondingly. Press 5/ again to
zoom out.

Press SNAPSHOT on the side of handset to take a photo shot of the visitor.

•

Press , then press + or - to adjust the video streaming brightness.

•

Press the flashing /VIEW when the screen displays Session is ending...

•

Press [VIEW] to extend. to extend the video streaming session.

End a video streaming session

Press OFF.

•

Answering an incoming call during video streaming

If you receive an outside call during a video streaming session, there is an
alert tone.

To answer the outside call, press on the handset. The video streaming

•
session ends automatically.

To end the video streaming session without answering the outside call, press

•

OFF. The video streaming session ends and the telephone continues to ring.

View captured photos

When the visitor presses /DOORBELL, the system automatically captures
a photo.

Press MENU when the phone is not in use.

1.
Scroll to Photo log and then press SELECT.

2.

If you have more than one doorbell, scroll to the desired doorbell or scroll to

•

All, and then press SELECT.

Delete a captured photo

When the desired photo displays, press DELETE.

•

Delete all captured photos

Press MENU when the phone is not in use.

1.
Scroll to Photo log and then press SELECT.

2.
Scroll to Delete all and then press SELECT. Press YES.

3.

6

Telephone operation

Make a call

Press or and then dial the telephone number.

•

Answer a call

Press , or any dialing key.

•

End a call

Press OFF or put the handset back in the telephone base or

•
charger.

Handset speakerphone

During a call, press to switch between the speakerphone

•
and the
handset earpiece.

Volume

During a call, press q/VOL- or p/VOL+ to adjust the

•
listening volume.

Equalizer

During a call, press EQ repeatedly to change the quality of the audio to best suit

•
your hearing.

Mute

The mute function allows you to hear the other party but the
other party cannot hear you.

During a call, press MUTE. The handset displays

1.
Microphone off.

Press MUTE to resume the conversation. The handset

2.
displays Microphone on briefly.

Call waiting

When you subscribe to call waiting service from your telephone service provider,
you hear an alert tone if there is an incoming call while you are already on a call.

Press FLASH to put the current call on hold and take the new call.

•
Press FLASH at any time to switch back and forth between calls.

•

Temporary ringer silencing

When the telephone is ringing, you can temporarily silence the ringer without
disconnecting the call. The next call rings normally at the preset volume.

To silence the handset ringer:

Press OFF, MUTE or SILENCE, then displays and Ringer muted

•
displays briefly.

To silence the telephone base ringer:

Press VOL/- on the telephone base.

•

Temporary tone dialing

If you have pulse (rotary) service only, you can switch from pulse to touch-tone
dialing temporarily during a call.

During a call, press .

1.
Use the dialing keys to enter the relevant number. The telephone sends

2.
touch-tone signals. It automatically returns to pulse dialing mode after you end
the call.

Find handset

Use this feature to find all system handsets.

To start paging:

Press /FIND HANDSET on the telephone base. All idle handsets ring and

•
display ** Paging **.

To end paging:

Press /FIND HANDSET again on the telephone base.

•
Press , , CANCEL or any dialing key on the handset.

•

Press MUTE or SILENCE on other handsets to mute the ringer so that you can hear

•
the ringing of the handset you are looking for.

7

Redial list

Each handset stores the last 10 telephone numbers dialed. When there are
already 10 entries, the oldest entry is deleted to make room for the new entry.

To review and dial a number from the redial list:

Press REDIAL when the phone is not in use.

1.

Press q, p or REDIAL repeatedly until the desired entry displays.

2.
Press or to dial.

3.

To delete a redial entry:
When the desired redial entry displays, press DELETE.

Join a call in progress

You can use four cordless handsets at a time on an outside call. You can buy
additional expansion handsets (IS7101) for this telephone base. You can register
up to 12 handsets to the telephone base, including a maximum of two doorbells.

When a handset is on a call, press or on another handset to join the call.

•
Press OFF to exit the call. The call continues until all handsets hang up.

•

Transfer a call

While on an outside call, you can transfer the call from one handset to another.

During a call, press OPTION.

1.
Press q

2.

•

To answer the call on the destination handset, press or .

3.

or

p to scroll to Transfer, then press SELECT.

When you have more than two handsets, press q or p to scroll to a
destination handset number, then press SELECT; or use the dialing keys
to enter a destination handset number.

Intercom

Use the intercom feature for conversations between two cordless handsets.

Press INTCOM on the handset when not in use.

1.

When you have more than two handsets, press q or p to scroll to a

•

destination handset number then press SELECT; or use the dialing keys
to enter a destination handset number.

To answer the call, press , or any dialing key.

2.
To end the intercom call, press END, OFF or place the handset back in the

3.
telephone base or charger.

Answer an incoming call during an intercom call

If you receive an outside call during an intercom call, there is an alert tone.

To answer the outside call, press on the handset. The intercom call

•
ends automatically.

To end the intercom call without answering the outside call, press OFF. The

•
intercom call ends and the telephone continues to ring.

Push to talk (PTT)

You can directly broadcast messages from one handset to the speakerphone
of one or multiple handsets. Press and hold PUSH TO TALK to begin two-way
communication.

When the connection is made, both the caller and the destination handsets display
Press and hold [PTT] to talk and beep once. Only one handset can talk at a time.
To do so, press and hold PUSH TO TALK.

Directory

The directory can store up to 50 directory entries which is shared by all handsets.

To add a directory entry:

Enter the number (up to 30 digits) when the phone is not in use then press

1.

SAVE. Then go to Step 3.

-OR­When the phone is not in use, press MENU. Scroll to Directory and then press

SELECT. Press q or p to scroll to Add contact and then press SELECT.

Use the dialing keys to enter the number (up to 30 digits).

2.

-OR­Copy a number from the redial list by pressing REDIAL and then press q, p or

REDIAL repeatedly to select a number. Press INSERT to copy the number.

Press NEXT to move on to enter the name.

3.
Use the dialing keys to enter the name (up to 15 characters). Additional key

4.
presses show other characters of that particular key.

Press SAVE to save.

5.

8

While entering names and numbers, you can:

Press DELETE or BACKSP to backspace and erase a digit or character.

•
Press and hold DELETE to erase the entire entry.

•
Press q or p to move the cursor to the left or right.

•
Press and hold PAUSE to insert a dialing pause (for entering numbers only).

•
Press to switch the character between upper and lower case.

•
Press 0 to add a space (for entering names only).

•

To review and dial a number from the directory:

Entries are sorted alphabetically.

Press when the phone is not in use.

1.
Scroll to browse through the directory.

2.
When the desired entry appears, press or to dial.

3.

To edit a directory entry:

When the desired entry displays, press EDIT.

1.
Use the dialing keys to edit the number, then press NEXT.

2.
Use the dialing keys to edit the name, then press SAVE to confirm.

3.

To delete a directory entry:

When the desired entry displays, press DELETE.

1.
When the handset displays Delete contact? and the name of the entry,

2.
press YES.

Speed dial

You can copy up to nine directory entries into the speed dial locations (0 and 2-9)
so that you can dial these numbers more quickly.

To assign a speed dial entry:

Press MENU when the phone is not in use.

1.
Scroll to Directory, then press SELECT.

2.
Scroll to Speed dial, then press SELECT.

3.
Scroll to a desired speed dial location, then press ASSIGN.

4.
Scroll to a desired directory entry, then press ASSIGN to save.

5.

To dial a speed dial entry:

Press and hold a dialing key (0 or 2-9) to dial the number stored in the

•
corresponding location.

To delete a speed dial entry:

Press MENU when the phone is not in use.

1.
Scroll to Directory, then press SELECT.

2.
Scroll to Speed dial, then press SELECT.

3.
Scroll to a desired speed dial location, then press DELETE or DELETE. The

4.
handset displays Delete Entry A speed dial assignment? Press YES.

Caller ID

This product supports caller ID services provided by most telephone service
providers. Depending on your service subscription, you may see the caller’s name,
number, date and time of calls that are sent by your telephone service provider
after the first or second ring.

Caller ID log

The caller ID log stores up to 50 entries. If you answer a call before the caller ID
information displays, it will not be saved in the caller ID log.

The handset displays XX Missed calls when you have incoming calls that have

•
not been answered.

If you want to erase the missed call indicator, press and hold CANCEL on the

•
idle handset, then press YES.

To review and dial a number in the caller ID log:

Press CID when the phone is not in use.

1.
Scroll to browse through the caller ID log. When the desired entry appears:

2.

Press repeatedly to show different dialing options.

•

Press 1 repeatedly if you need to add or remove 1 in front of the

•

telephone number.

Press or to dial.

3.

To save a caller ID log entry to the directory:

When the desired caller ID log entry displays, press SAVE.

1.
Use the dialing keys to modify the number, if necessary. Then press NEXT.

2.
Use the dialing keys to modify the name, if necessary. Then press SAVE.

3.

To delete a caller ID log entry:

When the desired caller ID log entry displays, press DELETE.

•

To delete all caller ID log entries:

Press MENU when the phone is not in use.

1.
Scroll to Caller ID log and then press SELECT.

2.
Scroll to Del all calls and then press SELECT. Press YES.

3.

9

About answering system and voicemail

Your telephone has separate indicators for two different types of voice messages:
those left on the built-in answering system and those left at your telephone service
provider’s voicemail. Each alerts you to new messages differently.

If XX new msgs displays on the handsets, there are messages recorded on the

•
built-in answering system. It can record up to 99 messages, depending on the
length of each message. Each message can be up to three minutes in length.
The total recording time is approximately 14 minutes.

If and New voicemail display on the handsets, your telephone service

•
provider is indicating that it has new voicemail for you. Contact your telephone
service provider for more information on how to access your voicemail.

Answering system settings

Default settings are indicated by asterisks (*).

Settings menu Description Options

Call screening

# of rings

Remote code

Msg alert tone

Recording time

Set whether you hear the callers while they are
leaving messages to you.

Set the number of times the telephone rings
before the answering system answers.

Set a two-digit security code to access the
answering system remotely from any touch­tone telephone.

Set whether the telephone beeps every
10 seconds to alert you of new messages.

Set the recording time for each
incoming message.

On*;
Off

6; 5; 4*; 3; 2;
Toll saver

19*

On;
Off*

3 minutes*;
2 minutes;
1 minute

Set number of rings

You can set the answering system to answer an incoming call after two, three,
four, five or six rings; or toll saver. If you choose toll saver, the answering system
answers a call after two rings when you have new messages, or after four rings
when you have no new messages.

Press MENU when the phone is not in use.

1.
Scroll to AnsweringSys and then press SELECT.

2.
Scroll to Ans sys setup and then press SELECT.

3.
Scroll to # of rings and then press SELECT.

4.
Press q or p to choose 6, 5, 4, 3, 2 or Toll saver and then press SET to save.

5.

Record your own announcement

You can use the preset announcement to answer calls, or replace it with your own
recorded announcement. The announcement can be up to 90 seconds in length.

Press MENU when the phone is not in use.

1.
Scroll to AnsweringSys then press SELECT twice.

2.
Press RECORD. The handset announces, “Record after the tone. Press STOP

3.
when you are done.” After the tone, speak towards the handset microphone.

Press STOP when done.

4.

Answering system operation

Turn the answering system on or off

The answering system must be turned on to answer and record messages.

Press MENU when the phone is not in use.

1.
Scroll to AnsweringSys and then press SELECT.

2.
Scroll to Answer ON/OFF and then press SELECT.

3.
Press q or p to choose On or Off and then press SET.

4.

Message playback at the telephone base

Press /PLAY when the phone is not in use.
Options during playback:

Press +/VOL or VOL/- to adjust the speaker volume.

•
Press /SKIP to skip to the next message.

•
Press /REPEAT to repeat the playing message. Press /REPEAT twice to

•
listen to the previous message.

Press X/DELETE to delete the playing message. The system advances to the

•
next message.

Press /STOP to stop.

•

Call intercept

If you want to talk to the person whose message is being recorded, press or .

10

Add and register a handset

The cordless handset provided with your phone system is already registered. Each
handset is assigned a number that displays on the handset. Additional handsets
registered to the telephone system are assigned numbers in the sequential order.
This telephone system accommodates up to 12 handsets, including a maximum of
two doorbells.

You can add new handsets (IS7101, purchased separately) to your telephone
system. Each handset must be registered with the telephone base before use.
When first purchased and properly charged, each expansion handset displays
Put handset on BASE to register. The new handset should be charged without
interruption for at least 30 minutes before registering it to the telephone base.

To register a handset:

Make sure the handset is out of the telephone base or handset charger and

1.
shows Put handset on BASE to register. Place the handset you wish to
register in the telephone base.

The handset displays Registering handset... then displays HANDSET X

2.
Registered, and you hear a confirmation tone from the handset when
registration completes. It takes about 60 seconds to complete the

registration process.

Add and register a doorbell

The doorbell provided is already paired to the telephone base. You can add or
replace doorbells (IS741, purchased separately) to your telephone system. This
telephone system accommodates up to two doorbells.

Each new doorbell must be paired to the telephone base before use.
Make sure you plug in AC power before pairing it to the telephone base.

Press and hold /FIND HANDSET on the telephone base for about four

1.
seconds until the IN USE light turns on.

Press and hold /DOORBELL for about 10 seconds until the doorbell light

2.
flashes slowly. The doorbell light turns on and you hear a confirmation tone
from the doorbell when registration completes. It takes about 60 seconds to

complete the registration process.

Deregister handsets and doorbells

If you want to replace a handset or doorbell, or reassign the designated handset
number of a registered handset, you must deregister all system devices and then
register each handset/doorbell individually.

Make sure you plug in AC power for the doorbells before deregistration.

To deregister all handsets and doorbells:

Press and hold /FIND HANDSET on the telephone base for about 10 seconds

1.
until the IN USE light flashes.

Immediately press /FIND HANDSET again. You must press /FIND HANDSET

2.
while the IN USE light is still flashing. The IN USE light flashes for about
five seconds.

All handsets show Put handset on BASE to register and all doorbell lights

3.
flash quickly. The deregistration process takes about 10 seconds to complete.

Troubleshooting

If you have difficulty with your telephone, please try the suggestions below.
For customer service, visit our website at www.vtechphones.com or call

1 [phone]. In Canada, go to www.vtechcanada.com or call 1 [phone].

My telephone does not work at all.

Make sure the battery is installed and charged correctly. For optimum daily

•

performance, return the handset to the telephone base after use.
Make sure the power adapter is securely plugged into an outlet not controlled by

•

a wall switch.
Make sure the telephone line cord is plugged firmly into the telephone base and

•

the wall jack.
Unplug the electrical power to the telephone base. Wait for approximately

•

15 seconds, then plug it back in. Allow up to one minute for the cordless handset
and telephone base to synchronize.

Charge the battery in the handset for up to 11 hours.

•

If the battery is completely depleted, charge the handset for at least 30 minutes

•

before use.
Remove the battery and then install it again. If that still does not work, it may be

•

necessary to purchase a new battery.
Disconnect the telephone base from the telephone wall jack and plug in a working

•

telephone. If the other telephone does not work, the problem is probably in the
wiring or telephone service. Contact your telephone service provider.

The display shows No line. I cannot hear the dial tone.

Disconnect the telephone line cord from your telephone and connect it to another

•

telephone. If there is no dial tone on that other telephone either, then the telephone
line cord may be defective. Try installing a new telephone line cord.

If changing telephone line cord does not help, the wall jack (or the wiring to this wall

•

jack) may be defective. Contact your telephone service provider.

11

You may be using a new cable or VoIP service, the existing telephone jacks in your

•

home may no longer work. Contact your service provider for solutions.

The answering system does not answer after the correct number of rings.

Make sure the answering system is on. When the answering system is on,

•

ANS ON should display on the handset and the telephone base.
If toll saver is selected, the number of rings changes to two when there are new

•

messages waiting.
If the memory is full or if the answering system is off, the answering system

•

answers after 10 rings.
In some cases, the answering system is affected by the ringing system used by

•

your telephone service provider.
If you subscribe to voicemail service, change the number of rings so that your

•

answering system answers before your voicemail answers. To determine how
many rings activate your voicemail, contact your telephone service provider.

If there is a fax machine connected to the same telephone line, try disconnecting

•

the fax machine. If that solves the problem, consult your fax machine
documentation for information on compatibility with answering systems.

The answering system does not record messages.

Make sure the answering system is on.

•

When the answering machine memory is full, it does not record new messages

•

until some old messages are deleted.
If you subscribe to voicemail service, change the number of rings so that your

•

answering system answers before your voicemail answers. To determine how
many rings activate your voicemail, please contact your telephone service
provider.

If there is a fax machine connected to the same telephone line, try disconnecting

•

the fax machine. If that solves the problem, consult your fax machine
documentation for information on compatibility with answering systems.

The messages on the answering system are incomplete.

If a caller leaves a very long message, part of it may be lost when the answering

•

system disconnects the call after the preset recording time.
If the memory on the answering system becomes full during a message, the

•

answering system stops recording and disconnects the call.
If the caller’s voice is very soft, the answering system may stop recording and

•

disconnect the call.

I accidentally set my LCD language to Spanish or French, and I don’t
know how to change it back to English.

While the handset is in idle mode, press MENU and then enter 364 .

•

While the handset is on a call, press OPTION and then enter 364 .

•

The doorbell does not work.

Make sure the doorbell is installed correctly. Refer to the Installation guide

•

for details.
Make sure the doorbell is powered up.

•

Common cure for electronic equipment.

If the telephone is not responding normally, put the cordless handset in the

•

telephone base. If it does not respond, try the following (in the order listed):

1. Disconnect the power to the telephone base.

2. Disconnect the battery on the cordless handset.

3. Wait a few minutes before connecting power to the telephone base.

4. Install the battery again and place the cordless handset in the telephone base.

5. Wait for the cordless handset to synchronize with the telephone base. Allow up
to one minute for this to take place.

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury, including the following:

Read and understand all instructions.

1.
Follow all warnings and instructions marked on the product.

2.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a

3.
damp cloth for cleaning.

Do not use this product near water such as near a bath tub, wash bowl, kitchen sink, laundry tub or a

4.
swimming pool, or in a wet basement or shower.

Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

5.
Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation.

6.
To protect them from overheating, these openings must not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation is not provided.

This product should be operated only from the type of power source indicated on the marking label. If you

7.
are not sure of the type of power supply in your home or office, consult your dealer or local power company.

Do not allow anything to rest on the power cord. Do not install this product where the cord may be

8.
walked on.

Never push objects of any kind into this product through the slots in the telephone base or handset

9.
because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind
on the product.

To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service

10.
facility. Opening or removing parts of the telephone base or handset other than specified access doors
may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock
when the product is subsequently used.

Do not overload wall outlets and extension cords.

11.
Unplug this product from the wall outlet and refer servicing to an authorized service facility under the

12.
following conditions:

When the power supply cord or plug is damaged or frayed.

•

If liquid has been spilled onto the product.

•

If the product has been exposed to rain or water.

•

If the product does not operate normally by following the operating instructions. Adjust only those

•

controls that are covered by the operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized technician to restore the
product to normal operation.

12

If the product has been dropped and the telephone base and/or handset has been damaged.

•

If the product exhibits a distinct change in performance.

•
Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric

13.
shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain circumstances, a

14.
spark may be created when the adapter is plugged into the power outlet, or when the handset is replaced
in its cradle. This is a common event associated with the closing of any electrical circuit. The user should
not plug the phone into a power outlet, and should not put a charged handset into the cradle, if the
phone is located in an environment containing concentrations of flammable or flame-supporting gases,
unless there is adequate ventilation. A spark in such an environment could create a fire or explosion.
Such environments might include: medical use of oxygen without adequate ventilation; industrial gases
(cleaning solvents; gasoline vapors; etc.); a leak of natural gas; etc.

Only put the handset of your telephone next to your ear when it is in normal talk mode.

15.
The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs

16.
are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary

evaluation of the interference between portable wireless telephones and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at least six inches from the pacemaker.

•

Should NOT place wireless telephones directly over the pacemaker, such as in a breast pocket, when it

•

is turned ON.
Should use the wireless telephone at the ear opposite the pacemaker.

•

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using
wireless telephones.

Operating range

This cordless telephone operates with the maximum power allowed by the Federal Communications
Commission (FCC). Even so, this handset and telephone base can communicate over only a certain
distance - which can vary with the locations of the telephone base and handset, the weather, and the
layout of your home or office.

When the handset is out of range, the handset displays Out of range or no pwr at base.
If there is a call while the handset is out of range, it may not ring, or if it does ring, the call may not connect
well when you press . Move closer to the telephone base, then press to answer the call.
If the handset moves out of range during a telephone conversation, there may be interference. To improve

reception, move closer to the telephone base.

ECO mode

This power conser ving technology reduces power consumption for optimal battery performance. The ECO
mode activates automatically whenever the handset is synchronized with the telephone base.

Maintenance

Taking care of your telephone

Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original packing materials to protect your telephone if you ever
need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with
wet hands. Do not install the telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own
safety, take caution when using electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft
cloth slightly dampened with water or mild soap. Do not use dampened cloth or cleaning solvents of any kind.

Remember that electrical appliances can cause serious injury if used when you are wet or standing in
water. If the telephone base should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE
POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the
unplugged cords.

About cordless telephones

Privacy: The same features that make a cordless telephone convenient create some limitations.

•

Telephone calls are transmitted between the telephone base and the cordless handset by radio
waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio
receiving equipment within range of the cordless handset. For this reason, you should not think of
cordless telephone conversations as being as private as those on corded telephones.

Electrical power: The telephone base of this cordless telephone must be connected to a working

•

electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made
from the cordless handset if the telephone base is unplugged, switched off or if the electrical power
is interrupted.

Potential TV interference: Some cordless telephones operate at frequencies that may cause

•

interference to televisions and VCRs. To minimize or prevent such interference, do not place the
telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced,
moving the cordless telephone farther away from the TV or VCR often reduces or eliminates
the inter ference.

Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with

•

conducting material such as rings, bracelets and keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between the battery and the battery charger.

Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not

•

burn or puncture the batter y. Like other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.

13

The RBRC® seal

The RBRC® seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to collect
and recycle these batteries at the end of their useful lives, when taken out of ser vice
within the United States and Canada.

The RBRC® program provides a convenient alternative to placing used nickel-metal
hydride batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery
at local retailers participating in the RBRC® program or at authorized VTech product
service centers. Please call

1 (800) 8 BATTERYTM for information on Ni-MH battery recycling and disposal

bans/restrictions in your area. VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.

RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device
under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended
to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio /TV technician for help.

•

Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Privacy of communications may not
be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander according to the intended usage of the product. This
product has been tested and found to comply with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base and the door bell shall be installed and used such that
parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm
(8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must
comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line
and an RJ14 jack for two lines. See the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your
telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th
and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but
not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your
telephone service provider.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment
connected to your telephone line, ensure the connection of this equipment does not disable your alarm
equipment. If you have questions about what will disable alarm equipment, consult your telephone service
provider or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized
agents. For repair procedures, follow the instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service provider may temporarily
discontinue your telephone service. The telephone service provider is required to notify you before
interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be
given the opportunity to correct the problem and the telephone service provider is required to inform you
of your right to file a complaint with the FCC. Your telephone service provider may make changes in its
facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The
telephone service provider is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers

(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation.

Privacy of communications may not be ensured when using this phone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical

specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN is an indication of

the maximum number of devices allowed to be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices does not exceed five.

This product meets the applicable Industry Canada technical specifications.

For C-UL compliance only

Mesures de sécurité importantes

Afin de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez toujours ces
mesures préventives de base lorsque vous utilisez votre téléphone :

Lisez et comprenez bien toutes les instructions.

1.

Observez toutes les instructions et mises en garde inscrites sur l’appareil.

2.

Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de nettoyeurs liquides

3.

ni en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.
N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier de cuisine, d’un bac

4.

de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la douche.

14

Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil pourrait tomber et

5.

être sérieusement endommagé.
Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière ou en dessous.

6.

Afin d’empêcher la surchauffe, ces ouvertures ne doivent pas être obstruées en plaçant l’appareil sur
un lit, divan, tapis ou autre surface similaires. Ne placez pas cet appareil à proximité d’un élément de
chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet
fermé qui ne possède pas d’aération adéquate.

Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes de l’appareil. Si vous

7.

ne connaissez pas le voltage de votre maison, consultez votre marchand ou votre fournisseur d’électricité.
Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit sécuritaire, là où

8.

personne ne pourra trébucher sur la ligne d’alimentation ni le cordon téléphonique modulaire.
N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils pourraient toucher à

9.

des points de tension dangereux ou court-circuiter des pièces, ce qui constituerait un risque d’incendie
ou d’électrocution. N’échappez pas de liquides dans l’appareil.

Afin de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le plutôt à un

10.

centre de service qualifié s’il doit être réparé. En enlevant le couvercle, vous vous exposez à des
tensions dangereuses ou autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation ultérieure de l’appareil. Débranchez l’appareil avant de procéder au
nettoyage. Utilisez un chiffon humide et doux.

Ne surchargez pas les prises de courant et les rallonges.

11.

Débranchez cet appareil de la prise de courant et communiquez avec le département de service à la

12.

clientèle de VTech dans les cas suivants:

Lorsque le cordon d’alimentation est endommagé ou écorché.

•
Si du liquide a été échappé dans l’appareil.

•
Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

•
Si le produit ne fonctionne pas

•
normalement en respectant les instructions de fonctionnement. Réglez uniquement les

•
commandes indiquées dans le les instructions de fonctionnement. Les réglages incorrects des
autres commandes pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de la
part d’un technicien autorisé afin de rétablir le fonctionnement normal de l’appareil.

Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.

•
Si le produit affiche une nette diminution de sa performance.

•

Évitez d’utiliser un téléphone (autre qu’un sans fil) pendant un orage. Les éclairs peuvent être à

13.
l’origine d’une électrocution.

14. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En cer taines
circonstances, une flammèche pourrait être provoquée lorsque l’adaptateur est branché à une prise
de courant, ou lorsque le combiné est déposé sur le socle. Ceci est un événement commun associé
à la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher le téléphone à une prise
de courant, et ne devrait pas déposer le combiné chargé sur le socle, si le téléphone se trouve à
proximité d’un endroit comportant des concentrations de gaz inflammables, à moins que la ventilation
soit adéquate. Une flammèche dans un tel endroit pourrait provoquer un incendie ou une explosion.
De tels environnements peuvent comprendre: des endroits où l’on utilise de l’oxygène médical sans
ventilation adéquate; des gaz industriels (dissolvants de nettoyage, des vapeurs d’essence, etc.); une
fuite de gaz naturel, etc.

15. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de conversation.

16. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au sol. Les
broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci est barnché dans une
prise au plafond ou sous une table/ armoire.

CONSERVEZ CES INSTRUCTIONS

Pile

MISE EN GARDE : Risque d’explosion si la pile est remplacée par une pile de types incorrects. Jetez les

•

piles épuisées en respectant les instructions.
Ne jetez pas la pile au feu. Vérifiez les instructions spécifiques de mise aux rebus auprès des autorités locales.

•

N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et pourrait causer des

•

brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est toxique si avalé.
Soyez prudents lorsque vous manipulez les piles afin d’éviter les courts-circuits provoqués par des

•

matériaux conducteurs.
Rechargez la pile incluse avec cet appareil, selon les instructions et limites spécifiées dans ce guide d’utilisation.

•

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené

une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

Ils doivent tenir le téléphone sans fil à une distance d’au moins six pouces du stimulateur cardiaque.

•

Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une

•

poche de chemise, lorsque celui-ci est en marche.
Ils doivent utiliser le téléphone sans fil en l’appuyant sur l’oreille qui se trouve dans la direction opposée

•

au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs
cardiaques causés par les gens qui utilisent un téléphone sans fil à proximité de ceux-ci.

À propos des téléphones sans fil

Alimentation électrique: Les mêmes caractéristiques qui constituent des avantages pour les téléphones

•

sans fil affichent également des restrictions. Les appels téléphoniques sont transmis entre le combiné sans
fil et le socle par le biais d’ondes radio ; il y a donc la possibilité que vos conversations téléphoniques sans
fil soient interceptées par des équipements de réception radio se trouvant dans la portée du combiné sans
fil. Pour cette raison, vous ne devez pas percevoir les communications téléphoniques sans fil comme étant
aussi confidentielles.

Alimentation électrique: Le socle de ce téléphone sans fil doit être branché à une prise électrique

•

fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur mural. Les appels ne
pourront pas être effectués du combiné sans fil si le socle est débranché ou mis hors tension ou si le
courant est coupé.

Possibilité d’interférences aux téléviseurs: Certains téléphones sans fil fonctionnent sur des fréquences

•

pouvant causer des interférences aux téléviseurs et aux magnétoscopes. Pour réduire ou prévenir de telles
interférences, ne placez pas le socle du téléphone sans fil près ou sur un téléviseur ou magnétoscope. S’il
y a présence de parasites, il est conseillé d’éloigner le téléphone sans fil du téléviseur ou du magnétoscope
afin de réduire possiblement les interférences.

Piles rechargeables: Manipulez les piles avec soin afin de ne pas les court-circuiter avec des bagues,

•

bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des blessures. Respectez la
polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel: Jetez ces blocs-piles de manière

•

écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres piles de ce type,
elles pourraient dégager une matière toxique qui peut causer des blessures corporelles si elles sont
brûlées ou percées.

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or
“you” ) that the Product and all accessories provided in the sales package ( “Product”) are free from defects
in material and workmanship, pursuant to the following terms and conditions, when installed and used
normally and in accordance with the Product operating instructions. This limited warranty extends only to
the Consumer for Products purchased and used in the United States of America and Canada.

15

What will VTech do if the Product is not free from defects in materials and workmanship during the
limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at
VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new
or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or
refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment.
Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the
repaired or replacement Products to you in working condition. You should expect the repair or replacement
to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited
warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the
date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one­year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper

installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or modification by anyone other than an

authorized service representative of VTech; or

3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or

cable or antenna systems; or

4. Product to the extent that the problem is caused by use with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have

been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or

Canada, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes); or

7. Product returned without a valid proof of purchase (see item 2 below); or

8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems

outside the unit.

How do you get warranty service?

To obtain warranty service in the USA, visit our website at www.vtechphones.com or call 1 [phone].

In Canada, go to www.vtechcanada.com or call 1 [phone].
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and

features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and

are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is
not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty,
VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity.
You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by
this limited warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along

with a description of the malfunction or difficulty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other
written or oral communications related to this Product. VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other
express warranties. No one is authorized to make modifications to this limited warranty and you should not
rely on any such modification.

State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights,
which vary from state to state or province to province.

Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase.
Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other
associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use
of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

Technical specications

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Handset: 1921.536-1928.448 MHz

Channels 5

LCD 128 (RGB) x 160 DOTS; 1.77’’; TFT PANEL

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may

Power requirements Handset unit: 2.4V Ni-MH battery

Memory Directory: 50 memory locations; up to 30 digits and 15 characters

Specification are subject to change without notice.
© 2014 VTech Communications, Inc.
All rights reserved. 05/14. IS7121-X_ACIB_V3.0
Document order number: 91-007180-030-100

Telephone base: 1921.536-1928.448 MHz
Doorbell: 1921.536 -1928.448 MHz

vary according to environmental conditions at the time of use.

Doorbell unit: Two 2A batteries
Base unit power adapter: input: 100- 120V AC 50/60Hz
output: 5V DC @ 450mA
Doorbell unit power adapter: input: 100 - 240V AC 50/60Hz
output: 6V DC @ 600mA
Charger unit power adapter: input :117V AC 50/60Hz
output: 5V DC @ 300mA

Caller ID log: 50 memory locations; up to 24 digits and 15 characters

16