Page 1
Installation guide
IS7121/IS7121-2/IS7121-22
DECT 6.0 cordless telephone
with wireless doorbell
Before using this product, read this Installation guide for
instructions for installing the telephone base, handset and
doorbell. For basic settings and operation instructions, see
the provided Abridged user’s manual.
Basic steps to install your phone and doorbell
Basic installation
1
Install telephone base & charger
2
Install handset battery
3
Install wall mount bracket
4
Install doorbell battery
Doorbell installation
Doorbell location testing
5
6
Doorbell wall mount installation
1
Page 2
1
Install telephone base & charger
Click!
Plug!
DSL lter
Click!
Plug!
Plug!
2
Page 3
2
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING : DO NOT BURN OR
PUNCTURE BATTERIES
Made in China CR1222
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
Install handset battery
1
Plug!
3 4
2
Light on!
Charge for at least 30 minutes
before initial settings.
Charge for 13 hours before
initial use.
3
Page 4
3
Install wall mount bracket (optional)
1
Unplug!
Unplug!
2
3
Slide the base down!
Click!
4
Slide the bracket down!
Plug!
4
Page 5
4
Install doorbell battery
The doorbell can be supported by AC power only. See pages 10 and 12 on how to
•
install the power adapter.
BASIC INSTALLATION COMPLETED!
Keep reading for doorbell location testing.
5
Before mounting the doorbell on a wall, make sure you test if
the location you install the doorbell is in range, and adjust the
camera angle to best suit your needs.
To test the location for installation:
Hold the doorbell in the location where you want to install the
doorbell, then follow the steps below to test the reception range
and video capture angle.
1.
2.
3.
4.
Doorbell location testing
Press MENU >> Press q or p to Settings >> Press
SELECT.
Press q or p to Doorbell setup >> Press SELECT.
Press /DOORBELL to check the video streaming quality.
Press ISO, then press + or - to adjust the video streaming
brightness.
If audio feedback occurs, press on the handset to turn off
•
the speakerphone.
If the desired location is in good range, the handset
•
displays .
If the desired location is not in good range, the handset
•
ashes in red. Press INFO for instructions to relocate
your handset and/or telephone base. When the reception
is in good range, the handset displays . Press OK to
return to the video streaming.
Keep the video streaming on for camera lens adjustment.
5
Page 6
When you check for the desirable location to install the doorbell:
Make sure the visitor is standing in a reasonable distance
•
away from the doorbell.
Shooting area
50 degrees
18
inches
20
63 inches
inches
Avoid mounting it to where it is exposed to direct sunlight.
•
Avoid mounting it to where reections may be caused by
•
sunlight, for example, opposite to a white wall.
Avoid placing other cordless devices near the doorbell.
•
They may cause interference.
Two built-in infrared LEDs are for night vision. Make sure the
•
surrounding light source is sufcient for infrared operation.
Test at the front door to determine when the infrared LEDs
turn on. When they are in operation, they turn red.
Infrared LEDs
6
Page 7
To adjust the shooting area, you may either relocate the doorbell
View
Right
Angle
Adjustment
View
Left
View
Right
Angle
Adjustment
View
Left
CAUTION
in different height level, or adjust the camera angle (see below).
To adjust the camera angle:
Tilt the lever to adjust the angle of the camera lens. The
•
camera lens can be adjusted to left, right or down, up to
10 degrees.
After you have tested the reception range and found the
desirable location to install the doorbell, press OK on the
handset to end the video streaming and proceed to Step 6.
DOORBELL LOCATION TESTING COMPLETED!
Keep reading for doorbell wall mount installation.
7
Page 8
6
1.
Doorbell wall mount installation
Make sure you have done Step 5 above before you
mount the doorbell on the wall.
Use the two holes on the doorbell wall mount cover to mark
the desirable installation location on the wall.
If you drill the holes into a stud, go to Step 3.
2.
-OR-
If you drill the holes into the wall, insert the wall anchors into
the holes.
8
Page 9
Align the holes on the wall mount cover with the holes on
3.
the wall. Tighten the screws into the holes to secure the wall
mount cover onto the wall.
Align
Use a sharp object to open a hole on the soft plastic part on
4.
the doorbell wall mount cover, then route the power adapter
cord through the hole.
Open a hole
and route the
cord through
the hole.
9
Page 10
Loosen the screws and the metallic plates, then slide the
5.
metal part of the wires underneath the metallic plates as
shown. Twist the screws to secure.
Metallic
plate
Screws
Metallic
plate
Wire with
red end
Wire with
black end
If you already have a wired doorbell
installed, see Installing the doorbell
with an existing wired doorbell from
pages 14 to 16 to install your new
IS7121 doorbell unit.
10
Page 11
Push the doorbell gently onto the wall mount until they are
6.
sealed tightly.
This doorbell meets the IPX4 waterproof standard. Make
sure the doorbell is tightly sealed with its wall mount cover in
order to maintain its waterproof ability.
Seal tightly
Push
Push
Tighten the screw into the threaded socket at the bottom
7.
to secure.
Tighten the
screw
11
Page 12
Plug the adapter into the indoor domestic power supply.8.
Plug!
DOORBELL INSTALLATION COMPLETED!
Refer to the Abridged user’s manual for
common settings and operations.
12
Page 13
Detach doorbell from wall mount cover
After an extended exposure to cold, heat or humidity, the
doorbell gasket rubber may become sticky.
If you need to remove the doorbell from its wall mount cover in
case of battery replacement or doorbell relocation, follow the
steps below.
Remove the screw at the bottom.
1.
Remove
the screw
Insert a at-bladed screwdriver between the doorbell and its
2.
wall mount cover.
Pry open at
both sides
Pry the doorbell off.
3.
Pry off the
doorbell
13
Page 14
Installing the doorbell with an existing wired
Transformer
Transformer
View
Right
Angle
Adjustment
View
Left
doorbell (optional)
If you already have a wired doorbell installed, follow the
instructions below to install your new IS7121 doorbell unit.
Turn off the power supply to the existing wired doorbell.
1.
Follow Step 1 through Step 5 in Doorbell wall mount
2.
installation from pages 8 to 10.
Insert a cross-head screwdriver to the side of the battery
3.
compartment on the right, then twist and lift to loosen the
screw and the metallic plate. Using a wire, slide one end of
the metal part of the wire underneath the metallic plate, then
twist the screw to secure. Connect the other end to
the transformer.
Transformer
14
Page 15
Using another wire, slide one end of the metal part
View
Right
Angle
Adjustment
View
Left
4.
underneath the metallic plate on the doorbell, then connect
the other end to the Trans terminal of your chime/buzzer unit
of the wired doorbell.
Option 1: Ring the front doorbell of the existing wired
doorbell and the IS7121 doorbell simultaneously.
Transformer
Rear Trans
Front
Chime/buzzer of
wired doorbell
15
Page 16
Option 2: Ring the rear doorbell of the existing wired doorbell
View
Right
Angle
Adjustment
View
Left
and the IS7121 doorbell simultaneously.
Transformer
Transformer
Rear
Trans Front
Chime/buzzer of
wired doorbell
If you do not connect domestic power supply nor
install AA batteries to the IS7121 doorbell, only the
existing wired doorbell will ring when being pressed.
Follow Step 6 to Step 8 in Doorbell wall mount installation
5.
on pages 11 and 12 to complete the installation.
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc., Beaverton, Oregon 97008.
Distributed in Canada by VTech Technologies Canada Ltd., Richmond, B.C. V6W 1L5.
VTech is the registered trademark of VTech Holdings Limited.
Copyright © 2013 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Printed in China.
16
96-009141-050-100
Loading...